FC4A-J8C1 IDEC | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 2

Technical content

Features

Specifications con’t on following page Specifications For more information on these and other IDEC PLCs, visit: www.idec.com/PLC General Specifications Part Number FC4A-J8C1 FC4A-K2C1 Rated Power Voltage 24V DC Allowable Voltage Range 20.4 to 28.8V DC Terminal Arrangement See Analog I/O Module User’s Manual -pages 2-8 to 2-11 Connector on Mother Board MC1.5/10-G-3.81BK (Phoenix Contact) Connector Insertion/ Removal Durability 100 times minimum Internal Current Draw 40mA (5V DC) 60mA (5V DC) 0mA (24V DC) 0mA (24V DC) External Current Draw (Note) 50mA (24V DC) 85mA (24V DC) Weight 140g 110g Analog Input Specifications Part Number FC4A-J8C1 Analog Input Signal Type Voltage Input Current Input Input Range 0 to 10V DC 4 to 20mA Input Impedance 1 MΩ 100Ω AD Conversion Sample Duration Time 2ms maximum Sample Repetition Time 2ms maximum Total Input System Transfer TimeNote 1 8ms x channels + 1 scan time Type of Input Single-ended input Operating Mode Self-scan Conversion Method Successive approximation register method Input Error Maximum Error at 25°C ±0.2% of full scale Temperature Coefficient ±0.005% of full scale / °C Repeatability after Stabilization Time ±0.5% of full scale Non-lineality ±0.04% of full scale Maximum Error ±1% of full scale Analog Output Specifications Part Number FC4A-K2C1 Output Range Voltage –10 to +10V DC Current 4 to 20mA DC Load Load Impedance 2 kΩ minimum (voltage), 300Ω maximum (current) Applicable Load Type Resistive load DA Conversion Settling Time 1ms / ch Total Output System Transfer Time 1ms x channels + 1 scan time Output Error Maximum Error at 25°C ±0.2% of full scale Temperature Coefficient ±0.005% of full scale/°C Repeatability after Stabilization Time ±0.5% of full scale Output Voltage Drop ±1% of full scale Non-lineality ±0.2% of full scale Output Ripple ±0.1% of full scale Overshoot 0% Total Error ±1% of full scale Data Digital Resolution 50000 increments (16 bits) Output Value of LSB Voltage 0.4mV Current 0.32µA Data Type in Application Program –25000 to 25000 (voltage) 0 to 50000 (current) Optional: –32768 to 32767 (selectable for each channel)Note 2 Monotonicity Yes

Specifications con’t IDEC Corporation • 1175 Elko Drive • Sunnyvale, CA 94089 • 800-262-IDEC (4332) • Fax: 408-745-5258 • www.idec.com ©2007 IDEC Corporation. All Rights Reserved. 03/07 Analog Input Specifications Data Digital Resolution 50000 increments (16 bits) Input Value of LSB 0.2mV 0.32µA Data Type in Application Program Default: 0 to 50000 Monotonicity Optional: –32768 to 32767 (selectable for each channel)Note 2 Input Data Out of Range DetectableNote 3 Noise Resistance Maximum Temporary Deviation during Electrical Noise TestsNote 4 ±3% maximum Input Filter Software Recommended Cable for Noise Immunity Twisted pair cable Crosstalk 2 LSB maximum Isolation Isolated between input and power circuit Photocoupler-isolated between input and internal circuit Effect of Improper Input Connection No damage Maximum Permanent Allowed Overload (No Damage) 11V DC 22 mA DC Selection of Analog Input Signal Type Using software programming Notes: 1. Total input system transfer time = Sample repetition time + Internal processing time. The total input system transfer time increases in proportion to the number of of channels used. 2. The data processed in the analog I/O module can be linear-converted to a a value between –32768 and 32767. The the optional range designation, and analog I/O data minimum and maximum values can be selected using data registers allocated to analog I/O modules. 3. When an error is detected, a corresponding error code is stored to a data register allocated to analog I/O operating status. 4. The value is measured when a 500V clamp voltage is applied to the power supply and I/O lines. Analog Output Specifications Current Loop Open Not detectable Noise Resistance Maximum Temporary Deviation during Electrical Noise TestsNote 4 ±3% maximum Recommended Cable for Noise Immunity Twisted pair cable Crosstalk 2 LSB maximum Isolation Isolated between output and power circuit Photocoupler-isolated be- tween output and internal circuit Effect of Improper Output Connection No damage Selection of Analog Output Signal Type Using software programming 103.0 90.0 2-ø4.36.3 23.5 3.0 113.0±0.2 Mounting Hole Layout (mm) FC4A-J8C1 23.5 14.6 70.0 90.04.5* 3.8 *8.5 mm when the clamp is pulled out. Dimensions (mm) 23.5 14.6 70.0 90.04.5* 3.8 *8.5 mm when the clamp is pulled out. FC4A-K2C1