F3000TERU MPD | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 2
Technical content
Key Features: 30W Output Power 4:1 Input Voltage Range 1,500 VDC Isolation Triple Outputs Compact 1.6 x 2 In. Case -40ºC to +85ºC Operation >1.0 MHour MTBF Remote ON/OFF Industry Standard Pin-Out F3000TERU Compact, 4:1 Input 30W, Triple Output DC/DC Con vert ers Series Electrical Specifi cations Specifi cations typical @ +25°C, nominal input voltage & rated output current, unless otherwise noted. Specifi cations subject to change without notice. Input Parameter Conditions Min. Typ. Max. Units Under Voltage Shutdown 24 VDC Input 8.0 9.0 VDC48 VDC Input 16.0 17.8 Input Filter, See Note 1 /H9266 (Pi) Filter Input Refl ected Ripple Current 30 mA Start Up Time 10 mS Output Parameter Conditions Min. Typ. Max. Units Output Voltage Accuracy Main Output ±1.0 ±3.0 %Auxiliary Outputs ±3.0 ±5.0 Line Regulation, For VIN Min to Max Main Output ±1.0 % Auxiliary Outputs ±5.0 Load Regulation, IOUT = 10% to 100% Main Output ±2.0 % Auxiliary Outputs ±5.0 Ripple & Noise, See Note 2 85 120 mV P - P Output Power Protection 110 130 % Transient Recovery Time, See Note 3 25% Load Step Change 300 500 µSec Transient Response Deviation ±3.0 ±5.0 % Temperature Coeffi cient ±0.03 %/°C Output Short Circuit Continuous (Autorecovery) General Parameter Conditions Min. Typ. Max. Units Isolation Voltage 60 Seconds 1,500 VDC Isolation Resistance 500 VDC 1,000 M/H9024 Isolation Capacitance 100 kHz, 0.1V 2,000 pF Switching Frequency 400 kHz Remote On/Off (Note 4) Parameter Conditions Min. Typ. Max. Units Supply On 3.5 12.0 VDC Supply Off -0.0 1.2 VDC Standby Input Current 1m A Control Common Referenced to Negative Input (pin 2) Environmental Parameter Conditions Min. Typ. Max. Units Operating Temperature Range Ambient -40 +85 °C Case +105 °C Storage Temperature Range -55 +125 °C Cooling Free Air Convection Humidity RH, Non-condensing 95 % Physical Case Material Metal with Non-Conductive Base Weight 1.76 Oz (50g) Reliability Specifi cations Parameter Conditions Min. Typ. Max. Units MTBF MIL HDBK 217F , 25°C, Gnd Benign 1,000 kHours Absolute Maximum Ratings Parameter Conditions Min. Typ. Max. Units Input Voltage Surge (1 Sec) 24 VDC Input -0.7 40.0 VDC48 VDC Input -0.7 80.0 Lead Temperature 1.5 mm From Case For 10 Sec 300 °C Caution: Exceeding Absolute Maximum Ratings may damage the module. These are not continuous operating ratings. www.micropowerdirect.com MicroPower Direct
292 Page Street
Stoughton, MA 02072 USA T: (781) 344-8226 F: (781) 344-8481 E: sales@micropowerdirect.com W: www.micropowerdirect.com Single & Dual Output Models Available F3000ERU Series
Mechanical Notes:
- All dimensions are typical in inch es (mm)
- Tolerance x.xx = ±0.01 (±0.25) Notes: 1. With the addition of a simple external circuit, the units will pass EN 55022 and EN 61000 EMI specifi cations. Contact the factory for recommendations. 2. When measuring output ripple, it is recommended that an external ceramic capacitor (see table at right) be placed from the +Vout pin to the -Vout pin for single output units and from each output to common for dual output units. 3. Transient recovery is measured to within a 1% error band for a load step change of 75% to 100%. 4. The Remote On/Off Control input (Pin 4) is referenced to -Vin (Pin 2). This input may be tied directly to ground, but it is recommended that connection to the pin should be made through a 1k/H9024 resistor and diode (1N4148). If it is not used, the control pin should be left open. 5. Operation at no-load will not damage these units. However, they may not meet all specifi cations. 6. It is recommended that a fuse be used on the input of a power supply for protection. See the table above for the correct rating. MicroPower Direct We Power Your Success - For Less! 292 Page Street Ste D Stoughton, MA 02072 TEL: (781) 344-8226 FAX: (781) 344-8481 E-Mail: sales@micropowerdirect.com Model Number Input Output 1 Outputs 2/3 Effi ciency (Typ %) Fuse Rating Slow-Blow (mA) Voltage (VDC) Current (mA) Voltage (VDC) Current (A, Max) Current (A, Min) OVP (VDC) Voltage (VDC) Current (A, Max) Current (A, Min) OVP (VDC)Nom. Range Full-Load No-Load VOUT Output Cap.
3.3 VDC 10 µF
5 VDC 10 µF
±12 VDC ±4.7 µF ±15 VDC ±4.7 µF Pin Function 1+ V IN 2- V IN
4 ON/OFF
www.micropowerdirect.com For Heatsink Option, add suffi x “H” to model number (i.e. F3003ERU-H) Heatsink Dimensions (Optional)