F06CT

F01 XPPOWER | Alldatasheet

Document overview

• Manufacturer or author: Provided By alldatasheet.com(free datasheet download site)
• PDF pages: 6

Technical content

Features

• Output Voltages from 100V to 12kV
• Output Voltage Proportional to Input
• Low Turn-on Voltage 0.7VDC
• Input to Output Isolation
• Dual Output Option
• Arc & Short Circuit Protected
• No Minimum Load
• 3 Year Warranty Typical Applications
• Mass Spectrometry
• Electrostatic Chucks
• Electrophoresis
• Capacitor Charging
• Particle Counter
• Isolation Testing
• Medical Laser Treatment Dimensions Block Diagram RECTIFIER & MULTIPLIE R Transforme r OSCILLATOR (+) Out put C ent er ta p( for Dual output op/g2462on) (-) Out pu t (+) In (-)I n

Notes: 1. Maximum rated output current is available at maximum rated output voltage and derates linearly as input voltage is decreased. 2. Output voltage is load dependent. Under light or no-load conditions, reduce the input voltage so maximum rated output voltage is not exceeded. 3. Specifications after 1 hour warm-up, full load, at 25°C unless otherwise indicated. 4. Proper thermal management techniques are required to maintain safe case temperature at maximum power output. 5. Ripple specification for center-tapped units applies to the voltage between the positive and negative output terminals. DC-HVDC CONVERTERF Series Output Characteristic Minimum Typical Maximum Units Notes & Conditions Output Voltage 12 000 VDC See Models & Ratings table Output Current 100 mA See Models & Ratings table Output Voltage Tolerance ±5 % At Max Vout, Full Load Minimum Load No minimum load required Regulation Unregulated, Output is proportional to Input. See Application Notes Short Circuit Protection Protected against short circuit conditions indefinitely Ripple and Noise 0.1 2.5 % 1See Models & Ratings table Response Time 260 msec 0 to Max Vout, Full Load Input Characteristic Minimum Typical Maximum Units Notes & Conditions Input Voltage Range 0.7 12, 15 VDC See Models & Ratings table Input Current, No Load 500 mA Input Current, Full Load 1.5 A Characteristic Minimum Typical Maximum Units Notes & Conditions Isolation: Input to Output 3500 V <±3,500 Bias for Models F01 to F60 Isolation: Input to Output 500 V <±500 Bias for Models F70 to F121 Switching Frequency 25 125 kHz Stable frequency over entire output voltage range. Construction Case material is black anodized aluminum. UL 94 V-0 rated solid vacuum encapsulation. Mean Time Between Failure 810 khrs Bellcore TR 332 General Environmental Characteristic Minimum Typical Maximum Units Notes & Conditions Operating Temperature -10 +70 °C Standard operating temperature Storage Temperature -25 +90 °C Cooling Natural convection Humidity 95 %RH Non-condensing

Specifications subject to change without notice. 3 Model Number Output Voltage Output Current(1) Input Voltage Ripple F01 0 to 100V 100mA 0 to 12V <0.6% F02 0 to 200V 50mA 0 to 12V <1.0% F02CT 0 +/-100V 50mA 0 to 12V <1.0% F02RH 0 to 200V 50mA 0 to 12V <1.0% F03 0 to 300V 33.3mA 0 to 12V <1.0% F03CT 0 to +/-150V 33.3mA 0 to 12V <1.0% F03H 0 to 300V 33.3mA 0 to 12V <1.0% F04 0 to 400V 25mA 0 to 12V <1.0% F04CT 0 to +/-200V 25mA 0 to 12V <1.0% F04CTH 0 to +/-200V 25mA 0 to 12V <1.0% F04H 0 to 400V 25mA 0 to 12V <1.0% F05 0 to 500V 20mA 0 to 12V <0.1% F05H 0 to 500V 20mA 0 to 12V <0.1% F06 0 to 600V 16mA 0 to 12V <0.1% F06CT 0 to +/-300V 16mA 0 to 12V <0.1% F08 0 to 800V 12.5mA 0 to 12V <0.1% F10 0 to 1000V 10mA 0 to 12V <0.1% F10CT 0 to +/-500V 10mA 0 to 12V <0.1% F12 0 to 1200V 8.3mA 0 to 12V <0.1% F12CT 0 to +/-600V 8.3mA 0 to 12V <0.1% F15 0 to 1500V 6.6mA 0 to 12V <0.1% F15CTH 0 to +/-750V 6.6mA 0 to 12V <0.1% F15H 0 to 1500V 6.6mA 0 to 12V <0.1% F20 0 to 2000V 5mA 0 to 12V <1.0% F30 0 to 3000V 3.3mA 0 to 15V <1.0% F30CT 0 to +/-1500V 3.3mA 0 to 15V <1.0% F30H 0 to 3000V 3.3mA 0 to 15V <1.0% F40 0 to 4000V 2.5mA 0 to 15V <1.0% F40CT 0 to +/-2000V 2.5mA 0 to 15V <1.0% F50 0 to 5000V 2mA 0 to 15V <1.0% F50CT 0 to +/-2500V 2mA 0 to 15V <1.0% F60 0 to 6000V 1.66mA 0 to 15V <1.0% F60CT 0 to +/-3000V 1.66mA 0 to 15V <1.0% F60H 0 to 6000V 1.66mA 0 to 15V <1.0% F80 0 to 8000V 1.25mA 0 to 15V <2.5% F80CT 0 to +/-4000V 1.25mA 0 to 15V <2.5% F101R 0 to 10,000V 1mA 0 to 15V <2.5% F121 0 to 12,000V 0.83mA 0 to 15V <2.5% F121CT 0 to +/-6000V 0.83mA 0 to 15V <2.5% Models & Ratings Notes: 1. All orderable part numbers are listed above. 2. CT indicates dual output, center tap. 3. H suffix indicates drilled mounting holes for F01 to F60. 4. R suffix is used as a RoHS indicator for legacy models.

Case T emperature Hot Spot 1.70 (43.18) 2.80 (71.12) “HOT SPOT” CASE TEMPERATURE POINT

Specifications subject to change without notice. 5 Mechanical Details Notes: 1. All dimensions are in inches (mm) 2. Weight 5oz (142g) 3. Tolerance: X.XX±0.02 (0.51) 4. Pin Tolerance: ±0.005 (0.127) 5. Case is inter nally connected to (-) Input. F01-F60 PCB Layout Pin Function 1 (+) Input 2 (-) Input 3 (+) Output 4 (-) Output

5 Dual Output/Center T ap (Optional)

#4/M3 CLEARANCE 2 HOLES. MTG HOLE (OPTIONAL) 2.80 (71.1)0.20 (5.1) 0.85 (21.6) 0.20 (5.1) 0.20 (5.1) 2.400 (60.96) PC PINS 0.031 (0.79) 1.70 (43.2) 2 4 1.750 (44.45) 0.650 (16.51) 0.250 (6.35) 0.100 (2.54) 0.400 (10.16) 0.900 (22.86) 0.800 (20.32) 1.050 (26.67) LOCATION OF MTG. HOLES (OPTIONAL) Ø 0.140 (3.56) 2PL 1.200 (30.48) HIGH VOLTAGE 1.300 (33.02) RECOMMENDED HOLE & PAD O.D. SIZE: *5 PLACES OPTIONAL DUAL OUTPUT (CENTER TAP) 0.45 (11.4) 0.85 (21.6) 6.00" (152.4mm) #22 AWG, 30KV OUTPUT LEADS: SILICONE MINIMUM LENGTH. 2 PLACES. 2 4 RECOMMENDED HOLE & PAD SIZE:

3 PLACES

Ø0.250 (6.35) CLEARANCE FOR 0.215" (5.46mm) O.D. OUTPUT LEADS

2 PLACES

0.85 (21.6) 0.400 (10.16) 1.400 (35.56) TOP VIEW 2.80 (71.1) 1.70 (43.2) MIN 0.25 (6.4) 0.95 (24.1) PC PINS ø0.040 (1.02) 0.800 (20.32) 0.45 (11.4) 1.200 (30.48) 1.30 (33.0) .25 (6.4) HIGH VOLTAGE Ø.140 (3.56) MTG HOLES, 2X #4/M3 CLEARANCE OPTIONAL DUAL OUTPUT (CENTER TAP) RECOMMENDED PCB LAYOUT TOP VIEW TOP VIEW RECOMMENDED PCB LAYOUT TOP VIEW #4/M3 CLEARANCE 2 HOLES. MTG HOLE (OPTIONAL) 2.80 (71.1)0.20 (5.1) 0.85 (21.6) 0.20 (5.1) 0.20 (5.1) 2.400 (60.96) PC PINS 0.031 (0.79) 1.70 (43.2) 2 4 1.750 (44.45) 0.650 (16.51) 0.250 (6.35) 0.100 (2.54) 0.400 (10.16) 0.900 (22.86) 0.800 (20.32) 1.050 (26.67) LOCATION OF MTG. HOLES (OPTIONAL) Ø 0.140 (3.56) 2PL 1.200 (30.48) HIGH VOLTAGE 1.300 (33.02) RECOMMENDED HOLE & PAD O.D. SIZE: *5 PLACES OPTIONAL DUAL OUTPUT (CENTER TAP) 0.45 (11.4) 0.85 (21.6) 6.00" (152.4mm) #22 AWG, 30KV OUTPUT LEADS: SILICONE MINIMUM LENGTH. 2 PLACES. 2 4 RECOMMENDED HOLE & PAD SIZE: Ø0.250 (6.35) CLEARANCE FOR 0.215" (5.46mm) O.D. OUTPUT LEADS 0.85 (21.6) 0.400 (10.16) 1.400 (35.56) TOP VIEW 2.80 (71.1) 1.70 (43.2) MIN 0.25 (6.4) 0.95 (24.1) PC PINS ø0.040 (1.02) 0.800 (20.32) 0.45 (11.4) 1.200 (30.48) 1.30 (33.0) .25 (6.4) HIGH VOLTAGE Ø.140 (3.56) MTG HOLES, 2X #4/M3 CLEARANCE OPTIONAL DUAL OUTPUT (CENTER TAP) RECOMMENDED PCB LAYOUT TOP VIEW TOP VIEW RECOMMENDED PCB LAYOUT TOP VIEW #4/M3 CLEARANCE 2 HOLES. MTG HOLE (OPTIONAL) 2.80 (71.1)0.20 (5.1) 0.85 (21.6) 0.20 (5.1) 0.20 (5.1) 2.400 (60.96) PC PINS 0.031 (0.79) 1.70 (43.2) 2 4 1.750 (44.45) 0.650 (16.51) 0.250 (6.35) 0.100 (2.54) 0.400 (10.16) 0.900 (22.86) 0.800 (20.32) 1.050 (26.67) LOCATION OF MTG. HOLES (OPTIONAL) Ø 0.140 (3.56) 2PL 1.200 (30.48) HIGH VOLTAGE 1.300 (33.02) RECOMMENDED HOLE & PAD O.D. SIZE: *5 PLACES OPTIONAL DUAL OUTPUT (CENTER TAP) 0.45 (11.4) 0.85 (21.6) 6.00" (152.4mm) #22 AWG, 30KV OUTPUT LEADS: SILICONE MINIMUM LENGTH. 2 PLACES. 2 4 RECOMMENDED HOLE & PAD SIZE: Ø0.250 (6.35) CLEARANCE FOR 0.215" (5.46mm) O.D. OUTPUT LEADS 0.85 (21.6) 0.400 (10.16) 1.400 (35.56) TOP VIEW 2.80 (71.1) 1.70 (43.2) MIN 0.25 (6.4) 0.95 (24.1) PC PINS ø0.040 (1.02) 0.800 (20.32) 0.45 (11.4) 1.200 (30.48) 1.30 (33.0) .25 (6.4) HIGH VOLTAGE Ø.140 (3.56) MTG HOLES, 2X #4/M3 CLEARANCE OPTIONAL DUAL OUTPUT (CENTER TAP) RECOMMENDED PCB LAYOUT TOP VIEW TOP VIEW RECOMMENDED PCB LAYOUT TOP VIEW PCB LayoutT op View

622 Jun 2022

Positive Output Negative Output Dual Output +Vin +Vout -Vout-Vin 2 1 3 +Vin -Vin 2 1 3 +Vin +Vout -Vin 2 1 3 -Vout4 +Vin +Vout -Vout-Vin 2 1 3 +Vin -Vin 2 1 3 +Vin +Vout -Vin 2 1 3 -Vout4 +Vin +Vout -Vout-Vin 2 1 3 +Vin -Vin 2 1 3 +Vin +Vout -Vin 2 1 3 -Vout4 Output Voltage vs. Input Voltage Typical HV output vs. Control voltage 100 150 200 250 300 01 02 03 04 05 06 07 08 09 01 00 % Control voltage % HV output Full load output No load output (A) No load output (AH) Safe operating limit Voltage input vs. Output voltage 100 120 140 01 02 03 04 05 06 07 08 09 0 100 % Output Voltage Full Load No Load % Input Voltage