EVW-AE4001B14 PANASONIC | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 7

Technical content

ELECTROMECHANICAL COMPONENTS BUSINESS UNIT AUTOMOTIVE DEVICE COMPANY Matsushita Electronic Components Co.,Ltd. OSAKA JAPAN SAMPLE SUBMISSION SHEET TO: DIGI-KEY CORPORATION Ref. No. 3116951-4 ATT: Date Jun.3:03 cc: CIISD: DEM: Ms.ITO T™: Mr.MATSUMOTO. Part Name VARIABLE RESISTOR Refer to A) MFirst submission for approval Mintroduction OResubmission B) SiThe samples are our standard product. (The samples meet your specifications (Dwg No. Rev. ) a Part No. Spec. No. Quantity Cost or Quotation No. mmm EVWAE4 001 B14. REFERENCE ONLY Spes. nn Remarks. + This product has not been manufactured with any ozone depleting chemical controlled under the Montreal Protocol. + All the materials used in this part contain no brominated materials or PPBOs or PBBs as the flame-retadant. + All the materials used in this part are registered material under the + Law Concerning the Examination and Regulation of Manufacture etc. or Chemical Substances. File: Name

ALL DIMENSIONS ARE IN MILLIMETERS. DO NOT SCALE DRAWING General dimension toleranace : 0.3 Mounting surface 0.8 2:8 ote 0.2 #2° oe cy 21k, sae 7 J oO O b, Ka Lo 1 4” ol Oe 2 54-4 WF Sith | L Jog | qo OF ie 7 Om OdO © | | —+ 5 N pap pe 2 \\ =, Amin oy Poj.0-1 oO ff a 3-1 g 0.2 2.5 2.5 12 8.4 2.2 e) oo} a cS , ols P.W.B piercing plan (lA (View from parts side.) ° W @ P.C.B thickness i=1.6 2-91-81 <J Tolerance : +0.1 9.4 e g. 410.05 8% Solder _lond 3 Ny 2 #2 #2’ #3 ge Shoft hole’s figure al 1 rat 2.8 tk P a seh ff \\\\ SY 41 #2 43 no ge) } ‘ ale J . aan +7 %

371.4 Xn #2 #1

2.5 2.5 Circuit diagram [besin [Y.SakamelalJan. 6. ’a3] NAME re ee [orw [ {| VARIABLE RESISTOR [ cHeck |QGGraeb Junk o3| TYPE NO. | DRAWING NO. W (evra Wize Planats] EV AEA O01 Bia | everenence owy/e Tsuyama Matsushita Electric Co.,Ltd. sen/sen-aeO-e0-evwae4001 -r00 :

Scope: 1) Control shown is designed in reference with our specifications. 2) Also see sample attached. General specifications: 1) Measurement condition Environment : Standard condition (According to JIC C5020) Temperature :15 C to35 Humidity 125 “RH to 85 %RH 2) Operating temperature range :-40 °C to90 °C 3) Storage temperature range 1-40 °C to 105 CT 4) Usage Voltage divided method (Potentiometer Connection) E Input impedance --- 1 MQ min. Mechanical specifications: 1) Mechanical Operating angle :360 ° (Endless) 2) Rotational torque :3mN-m or less (at 5 °C to 35 C) (expect No-output range) 3) Shaft pull-push strength :10N min. 4) Side thrust strength :10 mN-m min. F Shaft ‘orce Pull-push g _——_o eee pS Mie TRE {Mi | A | i —S Electrical specifications: 1) Nominal total resistance 710kQ+430% 2) Taper : Our code “B” 3) Power rating 0.05 W Power Derating Curve 100 , o | |N 1 2 o | | INT Sof [| i | I ae o 1 | | [| 0 20 40 60 80 90 Ambient Temperature (°C) 4) Maximum voltage :D-C5V 5) Insulation resistance :50MQ min. AtD-C 100 V (Between all VR terminals and a mounting bracket.) 6) Withstand voltage :A+C 100 V for 1 min. (Between all VR terminals and a mounting bracket.) 7) Noise level : Less than 100 mV (at D-C 5 V) (Micro linearity) NAME [| [| VARIABLE RESISTOR, ISSUE REVISIONS DATE TYPE No. DRAWING No. 2 EVW AE4 001 B14 RV-H— REFERENCE ONLY Wo Tsuyama Matsushita Electric Co.,Ltd.

8) Out put characteristic (346.65° ) 100% > g i ee} ia (13.35° ) 5 i oS 0% i <I o (so ° ) 360 AngleC ) (333.3 ° ) o No output. Electrical Rotation Angle No output _ Voltage between terminal #1 - #2 % Output = Voltage between terminal #1 #3 10008) 9) Linearity : Less than +2.5 % 100 % ° | ; Shaft shown in 180 ° position] < Theoretical straight line 3 #2 cw x 5 ch \\ : Cy > AN

3 YA ow 4

B | - 2g WA Deviation Ve oy, = P GS 3 0% i ° 320 ° GGunrantee range) | 33.3 ° ) Ser Operating angle 4 #2 #3 * Linearity :Ve/V X 100% (Deviation for theoretical straight line.) * Theoretical straight line : The straight line passing 50 % out put voltage. and having inclination of 100 % / 333.3 ° . * Measurement direction >CW NAME a VARIABLE RESISTOR. ISSUE REVISIONS DATE TYPE No. DRAWING No. EVW AE4 001 B14 RV-H— REFERENCE ONLY Hp Tsuyama Matsushita Electric Co.,Ltd.

Environmental specifications: ITEM TEST CONDITION __ SPECIFICATION. __ eee "eycle) Total resistance Rotation life Operation speed : 600 cycles/1 h, non-load chance ratio for ta =15% At normal temp. : 15 °C to 35 °C inearity - Within 9. 85 °C+3 °C, 240 h, non-load Total resistance High temperature (Measurement should be after Change ratio for initial : a4 % normalization in room temperature for 2h) | Linearity : Within +3.5% ~ 40 *C+3 C, 90 %RH to 95 %RH . 240 h. load. Total resistance Humidity » noneoae’ Change ratio for initial : +29 % (Measurement should be after : Tepe -10 ren Linearity : Within +3.5 % normalization in room temperature for 2 h) -40 +3 °C, 240 h, non-load. Total resistance Low temperature (Measurement should be after Change ratio for initial: +20 % normalization in room temperature for 2h) _| Linearity : Within +3.5 % 20 cycles, non-load [Below condition cycling 1-2°3-4-Le- T t li 1.-40 CT+3 C, ih Total resistance ome ae, oe) ng 2, Deviations time 5 min. Change ratio for initial: +15 % earn 3.85 C+3 C,ih Linearity : Within +3.5 % 4. Deviations time 5 min (Measurement should be after normalization in room temperature for 2 h) Soldering heat : No intermittent and breakdown after the below soldering. In case of hand soldering --- 300 “C max. 3s max. In case of reflow soldering --- In the below temperature profile. (Only 1 time) (c) S240 pmrree

3 Fl 3200 |-———aa mene ifO

g & 5 50~60 ar | 100~120 _|90 max, ° 0 Time(s) Notes: D Marking : (1) Our identification mark @) (2) Nominal total resistance (3) Taper code (4) Date code 2) Others : Correspond to JIS-C-6443 requirements. NAME a VARIABLE RESISTOR ISSUE REVISIONS DATE TYPE No. DRAWING No. EVW AE4 001 B14 RV—H-— REFERENCE ONLY Yo Tsuyama Matsushita Electric Co.,Ltd.

g [Je a oy | ri SESRSSS HSS FSGS SSS 7A Wa a Ps Oe Ds oe a a ae ed 4 jE 1 Cn CO CE i i i Take out direction x oS fals[eclo[elrle;uls{x«[ule| * Top tape (shall tape) strip strength : 0.2 N to 1.2 N Reel (1500pes./reel) Ly f £ ‘ 0 a - 4 \\ 1 p A - W t [ats [ec lofe«etwt. tne | NAME a VARIABLE RESISTOR lissiz[ REVISIONS | aE | EVW AE4 001 B14 RV-H— REFERENCE ONLY Ab Tsuyama Matsushita Electric Co.,Ltd.

III I TT LL CC | DIGI-KEY CORPORATION Prohibitions and precautions for handling. 1) Because of the construction of this product, an excessive stress, pressure to the body, or pressure or excessive force other than rotation to the hollow shaft portion may cause performance degradation in electrical, mechanical, life, or, feeling. To prevent this, please avoid any stress, pressure or force other than rotational one to the hollow shaft, and mounting the body should be by soldering pads only. 2) Avoid storing the products in a place at high temperature, high humidity and in corrosive gases. 8) Be careful to avoid excessive force when handling products, especially when inserting into PR W.B. so as to avoid deformation of terminals. 4) Prohibited items on fire and smoking + Absolutely avoid use of a potentiometer beyond its rated range because doing so may cause a fire. If misuse or abnormal use may result in conditions in which the potentiometer is used out of its rated range, take proper measures such as current interruption using a protective circuit. + The grade of nonflammability for resin used in potentiometers is “94HB”, which is based on UL94 Standards (flammability test for plastic materials). Prohibit use in a location where a spreading fire may be generated or prepare against a spreading fire. 5) For use in equipment for which safety requested + Although care is taken to ensure potentiometer quality, inferior characteristics, short circuits, open circuits are some problems that might be generated. To design a set which places maximum emphasis on safety , review the affect of any single fault of a potentiometer in advance and perform virtually fail-safe design to ensure maximum safety by: + Preparing a protective circuit or a protective device to improve system safety, and + Preparing a redundant circuit to improve system safety so that the single fault of a potentiometer does not cause a dangerous situation. 6) Reliability + The item designed mainly corresponds to JIS(Japan Industry Standard) on the reliability conditions. Handling of reference specification. + Since the contents of this reference specification are subjected to change without prior notifications, please request us a formal specification again for your investigations before using. NAME a a VARIABLE RESISTOR ISSUE REVISIONS TYPE No. DRAWING No. b EVW AE4 001 B14 RV-H— REFERENCE ONLY %, Tsuyama Matsushita Electric Co.,Ltd.