E200I MPD | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 2
Technical content
Key Features: 2W Output Power Ultra-Miniature SIP Case 3,000 VDC Isolation >2 MHour MTBF 18 Standard Models Industry Standard Pin-Out E200I High Isolation, 2W Ultra-Miniature, SIP DC/DC Con vert ers Series MicroPower Direct
292 Page Street
Stoughton, MA 02072 USA T: (781) 344-8226 F: (781) 344-8481 E: sales@micropowerdirect.com W: www.micropowerdirect.com Electrical Specifi cations Specifi cations typical @ +25°C, nominal input voltage & rated output current, unless otherwise noted. Specifi cations subject to change without notice. Input Parameter Conditions Min. Typ. Max. Units Input Voltage Range 5 VDC Input 4.5 5.0 5.5 VDC12 VDC Input 10.8 12.0 13.2 24 VDC Input 21.6 24.0 26.4 48 VDC Input 44.0 48.0 52.0 Reverse Polarity Input Current 0.3 A Input Filter Internal Capacitor Output Parameter Conditions Min. Typ. Max. Units Output Voltage Accuracy ±3.0 % Line Regulation For Vin Change of 1% ±1.2 % Load Regulation (Note 1) See Model Selection Guide Ripple & Noise (20 MHz) (Note 2) 100 mV P - P Output Power Protection 120 % Temperature Coeffi cient ±0.01 ±0.02 %/ºC Output Short Circuit Momentary (0.5 Sec.) General Parameter Conditions Min. Typ. Max. Units Isolation Voltage 60 Seconds 3,000 VDC Isolation Resistance 1,000 VDC 1,000 MΩ Isolation Capacitance 100 kHz, 1V 60 pF Switching Frequency 125 kHz Environmental Parameter Conditions Min. Typ. Max. Units Operating Temperature Range Ambient -40 +25 +85 ºC Operating Temperature Range Case +90 ºC Storage Temperature Range -55 +125 ºC Cooling Free Air Convection Humidity RH, Non-condensing 95 % Physical Case Material Non-Conductive Black Plastic (UL94-V0) Weight 0.06 Oz (1.8g) Reliability Specifi cations Parameter Conditions Min. Typ. Max. Units MTBF MIL HDBK 217F, 25ºC, Gnd Benign 2.0 MHours Absolute Maximum Ratings Parameter Conditions Min. Typ. Max. Units Input Voltage Surge (1 Sec) 5 VDC Input -0.7 9.0 VDC12 VDC Input -0.7 18.0 24 VDC Input -0.7 30.0 48 VDC Input -0.7 55.0 Lead Temperature 1.5 mm From Case For 10 Sec 260 ºC Internal Power Dissipation All Models 650 mW Caution: Exceeding Absolute Maximum Ratings may damage the module. These are not continuous operating ratings. RoHS Compliant
Notes: 1. Output load regulation is specifi ed for a load change of 20% to 100%. 2. When measuring output ripple, it is recommended that an external 0.33 µF ceramic capacitor be placed from the +Vout pin to the -Vout pin. 3. Operation at no-load will not damage these units. However, they may not meet all specifi cations. 4. The 5V, 12V and 24V input units do not require external components to operate, but the use of a low ESR capacitor (approximately 10 µF, ESR <1.0Ω at 100 kHz) mounted close to the converter input pins is recom- mended. For 48 VDC input units, an input capacitor should always be used. Depen- dent upon the application, a value between 4.7 µF and 47 µF should be suffi cient. 5. Out put capacitive load capability of these units is 33 µF max. Exceeding this may cause start up problems. 5. It is recommended that a fuse be used on the input of a power supply for protection. See the table above for the correct rating. Model Selection Guide Notes: All dimensions are typical in inches (mm) Tolerance x.xx = ±0.01 (±0.25) Pin 1 is marked by a “dot” or indentation on the side of the unit Mechanical Dimensions Pin Description 1- V i n 2+ V i n 3 -Vout 4 +Vout Pin Connections Model Number Input Output Load Regulation (% Max) Effi ciency (%, Typ) Fuse Rating Slow-Blow (mA) Voltage (VDC) Current (mA) Voltage (VDC) Current (mA, Max) Current (mA, Min)Nominal Range Full-Load No-Load MicroPower Direct www.micropowerdirect.com 292 Page Street Ste D Stoughton, MA 02072 TEL: (781) 344-8226 FAX: (781) 344-8481 E-Mail: sales@micropowerdirect.com Derating Curve