E15C5H2F-125.000M ECLIPTEK | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 6
Technical content
R REGULATORY COMPLIANCE (Data Sheet downloaded on Dec 7, 2016) 2011/65 +
169 SVHC
E15C5H2F-125.000M ITEM DESCRIPTION Quartz Crystal Clock Oscillators XO (SPXO) LVPECL (PECL) 2.5Vdc 6 Pad 3.2mm x 5.0mm Ceramic Surface Mount (SMD) 125.000MHz ±50ppm over -40°C to +85°C ELECTRICAL SPECIFICATIONS Nominal Frequency 125.000MHz Frequency Tolerance/Stability ±50ppm Maximum over -40°C to +85°C (Inclusive of all conditions: Calibration Tolerance (at 25°C), Frequency Stability over the Operating Temperature Range, Supply Voltage Change, Output Load Change, First Year Aging at 25°C, and Vibration) Supply Voltage 2.5Vdc ±5% Input Current 75mA Maximum Output Voltage Logic High (Voh) Vdd-1.085Vdc Minimum, 1.55Vdc Typical, Vdd-0.88Vdc Maximum Output Voltage Logic Low (Vol) Vdd-1.83Vdc Minimum, 0.80Vdc Typical, Vdd-1.555Vdc Maximum Rise/Fall Time 300pSec Typical, 700pSec Maximum (Measured at 20% to 80% of Waveform) Duty Cycle 50 ±5(%) (Measured at 50% of Waveform) Load Drive Capability 50 Ohms into Vdd-2.0Vdc Output Logic Type LVPECL Phase Noise -60dBc/Hz at 10Hz Offset, -95dBc/Hz at 100Hz Offset, -125dBc/Hz at 1kHz Offset, -143dBc/Hz at 10kHz Offset, - 145dBc/Hz at 100kHz Offset, -145dBc/Hz at 1MHz Offset, -146dBc/Hz at 10MHz Offset (All Values are Typical) Logic Control / Additional Output Tri-State and Complementary Output Tri-State Input Voltage (Vih and Vil) Vih of 70% of Vdd Minimum or No Connect to Enable Output and Complementary Output, Vil of 30% of Vdd Maximum to Disable High Impedance Output and Complementary Output Standby Current 30µA Maximum (Without Load) RMS Phase Jitter 0.4pSec Typical, 1pSec Maximum (Fj=12kHz to 20MHz; Random) Start Up Time 10mSec Maximum Storage Temperature Range -55°C to +125°C ENVIRONMENTAL & MECHANICAL SPECIFICATIONS ESD Susceptibility MIL-STD-883, Method 3015, Class 1, HBM: 1500V Fine Leak Test MIL-STD-883, Method 1014, Condition A Flammability UL94-V0 Gross Leak Test MIL-STD-883, Method 1014, Condition C Mechanical Shock MIL-STD-883, Method 2002, Condition B Moisture Resistance MIL-STD-883, Method 1004 Moisture Sensitivity J-STD-020, MSL 1 Resistance to Soldering Heat MIL-STD-202, Method 210, Condition K Resistance to Solvents MIL-STD-202, Method 215 Solderability MIL-STD-883, Method 2003 Temperature Cycling MIL-STD-883, Method 1010, Condition B Vibration MIL-STD-883, Method 2007, Condition A www.ecliptek.com | Specification Subject to Change Without Notice | Revision D 02/25/2013 | Page 1 of 6 Ecliptek Corporation 3545 Cadillac Ave., Costa Mesa, CA 92626 1-800-ECLIPTEK or 714.433.1200
R E15C5H2F-125.000M MECHANICAL DIMENSIONS (all dimensions in millimeters) 3.20 ±0.15 1.30 MAX 1.20 ±0.15 1.27 ±0.15 1.00 ±0.15 0.64 ±0.10 2.54 ±0.15 5.00 ±0.15 MARKING ORIENTATION PIN CONNECTION Tri-State No Connect Case/Ground Output Complementary Output Supply Voltage LINE MARKING E125.00 E=Ecliptek Designator XXXXX XXXXX=Ecliptek Manufacturing Identifier All Tolerances are ±0.1 Suggested Solder Pad Layout Solder Land (X6) All Dimensions in Millimeters 0.27 (X4) 0.80 (X2) 1.40 (X6) 1.00 (X6) www.ecliptek.com | Specification Subject to Change Without Notice | Revision D 02/25/2013 | Page 2 of 6 Ecliptek Corporation 3545 Cadillac Ave., Costa Mesa, CA 92626 1-800-ECLIPTEK or 714.433.1200
R E15C5H2F-125.000M HIGH IMPEDANCE STATE OUTPUT WAVEFORM & TIMING DIAGRAM VOH VOL 80% 50% 20% Fall Time Rise Time TW T Duty Cycle (%) = TW/T x 100 VIH VIL tPLZ tPZL Q & Q OUTPUTS TRI-STATE INPUT Q Q www.ecliptek.com | Specification Subject to Change Without Notice | Revision D 02/25/2013 | Page 3 of 6 Ecliptek Corporation 3545 Cadillac Ave., Costa Mesa, CA 92626 1-800-ECLIPTEK or 714.433.1200
R E15C5H2F-125.000M Power Supply Power Supply Power Supply Power Supply Oscilloscope Probe 2 (Note 2) Probe 1 (Note 2) Current Meter Voltage Meter Frequency Counter Switch 0.01µF (Note 1) 0.1µF (Note 1)
50 Ohms
(VDD) Tri-State Complementary Output Output No Connect Ground Note 1: An external 0.01µF ceramic bypass capacitor in parallel with a 0.1µF high frequency ceramic bypass capacitor close (less than 2mm) to the package ground and supply voltage pin is required. Note 2: A low capacitance (<12pF), 10X attenuation factor, high impedance (>10Mohms), and high bandwidth (>500MHz) passive probe is recommended. Note 3: Test circuit PCB traces need to be designed for a characteristic line impedance of 50 ohms. Test Circuit for Tri-State and Complementary Output www.ecliptek.com | Specification Subject to Change Without Notice | Revision D 02/25/2013 | Page 4 of 6 Ecliptek Corporation 3545 Cadillac Ave., Costa Mesa, CA 92626 1-800-ECLIPTEK or 714.433.1200
R E15C5H2F-125.000M Recommended Solder Reflow Methods High Temperature Infrared/Convection TS MAX to TL (Ramp-up Rate) 3°C/Second Maximum Preheat - Temperature Minimum (TS MIN) 150°C - Temperature Typical (TS TYP) 175°C - Temperature Maximum (TS MAX) 200°C - Time (tS MIN) 60 - 180 Seconds Ramp-up Rate (TL to TP) 3°C/Second Maximum Time Maintained Above: - Temperature (TL) 217°C - Time (tL) 60 - 150 Seconds Peak Temperature (TP) 260°C Maximum for 10 Seconds Maximum Target Peak Temperature (TP Target) 250°C +0/-5°C Time within 5°C of actual peak (tp) 20 - 40 Seconds Ramp-down Rate 6°C/Second Maximum Time 25°C to Peak Temperature (t) 8 Minutes Maximum Moisture Sensitivity Level Level 1 Additional Notes Temperatures shown are applied to body of device. www.ecliptek.com | Specification Subject to Change Without Notice | Revision D 02/25/2013 | Page 5 of 6 Ecliptek Corporation 3545 Cadillac Ave., Costa Mesa, CA 92626 1-800-ECLIPTEK or 714.433.1200
R E15C5H2F-125.000M Recommended Solder Reflow Methods Low Temperature Infrared/Convection 240°C TS MAX to TL (Ramp-up Rate) 5°C/Second Maximum Preheat - Temperature Minimum (TS MIN) N/A - Temperature Typical (TS TYP) 150°C - Temperature Maximum (TS MAX) N/A - Time (tS MIN) 60 - 120 Seconds Ramp-up Rate (TL to TP) 5°C/Second Maximum Time Maintained Above: - Temperature (TL) 150°C - Time (tL) 200 Seconds Maximum Peak Temperature (TP) 240°C Maximum Target Peak Temperature (TP Target) 240°C Maximum 2 Times / 230°C Maximum 1 Time Time within 5°C of actual peak (tp) 10 Seconds Maximum 2 Times / 80 Seconds Maximum 1 Time Ramp-down Rate 5°C/Second Maximum Time 25°C to Peak Temperature (t) N/A Moisture Sensitivity Level Level 1 Additional Notes Temperatures shown are applied to body of device. Low Temperature Manual Soldering 185°C Maximum for 10 Seconds Maximum, 2 times Maximum. (Temperatures shown are applied to body of device.) High Temperature Manual Soldering 260°C Maximum for 5 Seconds Maximum, 2 times Maximum. (Temperatures shown are applied to body of device.) www.ecliptek.com | Specification Subject to Change Without Notice | Revision D 02/25/2013 | Page 6 of 6 Ecliptek Corporation 3545 Cadillac Ave., Costa Mesa, CA 92626 1-800-ECLIPTEK or 714.433.1200