DSA480 XPPOWER | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 5

Technical content

DSA 480 Series AC -D C Pow er Supplies xxx Series w w w .xppow er.com 1 M odels & Ratings M echanical Details N otes 1. T ypical efficiency at 230 VAC and full load. 2. Peak load is for a m axim um of 3 s, see A pplication N otes. Average pow er is not to exceed nom inal output pow er. 3. O utput current should be lim ited so that nom inal output pow er is not exceeded.

  • Ultra Slim Design
  • 150% Peak Load for 3 seconds
  • Ambient Operation from -25 °C to +70 °C
  • High Efficiency – Up to 94%
  • Selectable Overload Characteristic
  • Selectable Remote Inhibit or Enable
  • 3 Year Warranty Dim ensions: DSA 480:

480 Watts

O utput Voltage O utput Pow er O utput Voltage Trim (3) O utput C urrent Peak Load (2) Typical Efficiency (1) M odel N um ber 24 V 4 80 W 23.5 2-25 .92 V 20.0 A 30.0 A 93% D SA 4 80PS24 4 8 V 4 80 W 4 7 .04 -5 1 .84 V 1 0.0 A 1 5 .0 A 94 % D SA 4 80PS4 8 Pin C onnector C onn Pin D esignation AC I/P

1 G round

9 D C O K

www.xppower.c om LN +V +V +V -V -V -V +RC -RC DC OK ON VOUT ADJ. 1 10 4.91 (124.8) 4.85 (123.3) 3.39 (86.3)

w w w .xppow er.com 2 AC -D C Pow er Supplies Input O utput C haracteristic M inim um Typical M axim um U nits N otes & C onditions O utput Voltage - V1 24 4 8 VD C See M odels and R atings table Initial Set A ccuracy ±1 % A t 1 00% load O utput Voltage Adjustm ent ±5 % See M odels and R atings table M inim um Load 0A N o m inim um load required Start U p D elay 1 .0 s Start U p R ise Tim e 1 30 m s H old U p Tim e 1 0 m s A t full load and 1 1 5 VAC Line R egulation ±0.5 % Load R egulation ±1 % T ransient R esponse - V1 4% R ecovery w ithin 1 % in less than 2 m s for a 5 0% step load change at 0.2 A /µs R ipple & N oise 1 % pk-pk M easured at 20 M H z bandw idth O vervoltage Protection 29 33 V 24 V m odel 5 6 65 V 4 8 V m odel O verload Protection % See A pplication N otes Short C ircuit Protection T rip & restart (hiccup m ode) for 5 cycles then latch. R ecycle AC to reset. Therm al Protection 95 (±5 ) °C M easured on internal heatsink auto recovery T em perature C oefficient 0.03 % /˚C R em ote O n/O ff Selectable as Enable or Inhibit using front panel sw itch C haracteristic M inim um Typical M axim um U nits N otes & C onditions Input Voltage - O perating 90 264 VAC Input Frequency 4 7 5 0/60 63 H z Pow er Factor 0.96 A t 230 VAC . C onform s to EN 61 000-3-2 C lass A Input C urrent - Full Load 5 .0/2.5 A 1 1 5 /230 VAC Inrush C urrent 33/65 A A t 1 1 5 /230 VAC Earth Leakage C urrent 1 .0 m A A t 264 VAC , 60 H z Input Protection T1 0.0 A / 25 0 V internal in-line fuse G eneral C haracteristic M inim um Typical M axim um U nits N otes & C onditions Efficiency 92 94 % See M odels & R atings table Isolation: Input to O utput Input to G round O utput to G round

3000 VAC

Sw itching Frequency 100 kH z PF C & M ain converter D C O K Signal Isolated opto-coupler output O utput LED G reen LED to indicate output on. M ean Tim e Betw een Failure >200 kH rs M IL-H D BK-21 7 F , +25 °C G B W eight 3.2 (1 .4 5 ) lb (kg)

w w w .xppow er.com AC -D C Pow er Supplies Environm ental C haracteristic M inim um Typical M axim um U nits N otes & C onditions O perating T em perature -25 +7 0 °C See derating curve in A pplication N otes Storage T em perature -4 0 +85 °C C ooling N atural convection O perating H um idity 20 95 % R H N on-condensing O perating A ltitude 3000 m Shock IEC 68-2-27 , 4 g, 22 m s half sine, 3 tim es in each of 6 axes Vibration IEC 68-2-6, 1 0-5 00 H z, 2 g 1 0 m ins/sw eep. 60 m ins for each of 3 axes Safety A pprovals EM C: Im m unity Phenom enon Standard Test Level C riteria N otes & C onditions ESD Im m unity EN 61 000-4 -2 6 kV A C ontact 8 kV A ir D ischarge R adiated Im m unity EN 61 000-4 -3 1 0 V/m A EF T/Burst EN 61 000-4 -4 3A Surges EN 61 000-4 -5 Installation class 3 A C onducted EN 61 000-4 -6 1 0 V A M agnetic F ields EN 61 000-4 -8 4A D ips and Interruptions EN 5 5 024 D ip: 30% , 1 0 m s A D ip: 60% , 1 00 m s A /B H igh Line/Low Line D ip: 1 00% , 5 000 m s B EM C: Em issions Phenom enon Standard Test Level C riteria N otes & C onditions C onducted EN 5 5 022 C lass B R adiated EN 5 5 022 C lass B H arm onic C urrent EN 61 000-3-2 C lass A Voltage F luctuations EN 61 000-3-3 Safety Agency Safety Standard N otes & C onditions U L U L508 Industrial C ontrol Equipm ent TU V EN 60950-1 A12:2011 Inform ation Technology C B IEC 60950-1 +A1:2009 Inform ation Technology

-25 Ambient Temperature (°C) 0 10 20 30 40 50 60 70 (V ertical) 90 100 110 135 264V ac Input V oltage(V) 230 100 112.5 150 Load (%) For typ. 3sec Continuous Load (%) 100 Derating Curves DC O K A pplication N otes DSA 480 Series w w w .xppow er.com 4 AC -D C Pow er Supplies 1 . A ll dim ensions in inches (m m ) 2. W eight: 3.2 lbs (1 .4 5 kg) 3. T olerance: ±0.02 in (±0.5 m m ) 4 . Screw term inal: 1 0-24 AW G cables size. N otes M echanical Details DC OK Emitter DC OK Collector 9

10 M axim um rating is 60VD C w hen pin 9 is positive W RT pin 1 0, 5 0m A sink current,

1 5 00 VAC isolation to output O pen (O ff): O utput fail, if voltage drops below 4 5 % of nom inal C losed (O n): O utput good 1 2 OCP Mode RC Mode DSA480 www.xppower.c om L N +V +V +V -V -V -V +RC -RC DC OK ON VOUT ADJ. 1 10 4.91 (124.8) 4.85 (123.3) 3.39 (86.3) Pin C onnector C onn Pin D esignation AC I/P

9 D C O K C ollector

w w w .xppow er.com AC -D C Pow er Supplies

19 March 15

I OCP Mode switch set to position 1 T I-recovery I-peak T-peak T-recovery OCP Mode switch set to position 2 I T I-peak T-peak 3 ~ 4 sec 10% 20% 30% 40% 50% 60% 70% 80% 90% I-norm al 110%115%120%125%130%135%140%145%150% Peak duration - I-peak GRAPH A GRAPH B (Sec.) Recovery duration (Sec.) Load (%) Load (%) The peak loading and overload characteristics can be program m ed into one of tw o m odes by appropriate selection of the O C P m ode sw itch on the front panel. A peak load of up-to 1 5 0% can be taken for a given duration. This duration depends on the percentage of peak load taken and can be determ ined by graph A below. If the load is reduced to less than 1 00% of nom inal either before or at the end of the duration, then there is a period of recovery needed to allow the pow er supply to cool dow n before the peak load can be re-applied. The tim e required for recovery depends on the am ount of reduction of load and can be determ ined by graph B below. H ow ever, if the peak load period exceeds the duration indicated by graph A the output w ill go into constant current m ode for protection. The constant current value w ill be 1 05 % of the nom inal rating. D uring constant current operation, if the output voltage should fall below 4 0% of the rated voltage then the output w ill turn off and try to restart for five tim es before turning off perm anently. O nce this has happened, the output w ill need to be reset by turning the AC m ains off and on again. The output can be controlled by applying a voltage betw een pin 3 of the D C output w ith respect to pin 4 . The effect of the control is dependant upon the R C sw itch setting on the front panel. If the sw itch is set to position 1 then the output can be disabled by applying a suitable voltage. If the sw itch is set to position 2 then the output can be enabled by applying a voltage. In the range of 2.5 V to 9.0 V lim ited to 20 m A . A peak load of up-to 1 5 0% can be taken for a given duration. This duration depends on the percentage of peak load taken as described by graph A . O nce the peak load duration is exceeded, the output w ill turn off for 3-4 seconds before autom atically restarting. Sw itch Position Pin 3 Voltage w ith respect to Pin 4 O utput 1 <0.8 V or O pen C ircuit O N 1 >2.5 V, <9.0 V O FF 2 <0.8 V or O pen C ircuit O FF 2 >2.5 V, <9.0 V O N