DGOF5S3 CONNOR-WINFIELD | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 2
Technical content
THE CONNOR-WINFIELD CORP. 2111 COMPREHENSIVE DRIVE. AURORA, IL 60505. FAX (630) 851-5040. PHONE (630) 851-4722. P R O D U C T D A T A S H E E T Specifications subject to change without notice. DATA SHEET #: REV: DATE: PAGE OF Copyright 2001 Connor-Winfield all rights reserved. a CRYSTAL CONTROLLED OSCILLATORS The Connor-Winfield DGOF5S3 is a hermetically sealed 14 Pin DIP, 5.0V Oven Controlled Crystal Oscillator (OCXO) HCMOS/TTL Compatible. The DGOF5S3 is designed for a higher stability Stratum 3 application requiring low jitter and tight stability. DGOF5S3 - 33.333333MHz OCXO SERIES CENTER FREQUENCY
FEATURES
DESCRIPTION
ORDERING INFORMATION
5.0V OPERATION LOW JITTER <3pS RMS TEMPERATURE STABILITY ±0.25ppm FREQUENCY TOLERANCE OF ±2.5ppm OVER TEN YEARS 14 PIN DIP 5.0V STRATUM 3 HCMOS OCXO Cx030 7/9/02 www.conwin.com DGOF5S3 CW 0107 DGOF5S3 33.333333M ABSOLUTE MAXIMUM RATINGS TABLE 1.0 PARAMETER UNITS MINIMUM NOMINAL MAXIMUM UNITS NOTE Storage Temperature -40 Supply Voltage (Vcc) -0.5 7.0 Vdc OPERATING SPECIFICATIONS TABLE 2.0 PARAMETER MINIMUM NOMINAL MAXIMUM UNITS NOTE Center Frequency (Fo) 2.50 38.88 MHz Frequency Calibration -1.0 1.0 ppm 1, 4 Frequency vs. change in Temperature -0.25 0.25 ppm Frequency vs. change in Supply Voltage -0.05 0.05 ppm Aging (Daily) -15 ppb/day Aging (1st Year) -0.7 0.7 ppm Total Frequency Tolerance -2.5 2.5 ppm Operating Temperature Range Supply Voltage (Vcc) 4.75 5.00 5.25 Vdc Supply Current (Icc) 300 mA Jitter (BW=10Hz to 20MHz) ps rms Allan Variance (1 second) 5.00E-10 SSB Phase Noise at 10Hz offset -90 dBc/Hz SSB Phase Noise at 10KHz offset -130 dBc/Hz Start Up Time: Oscillator mS Warm Up Time Minutes TDEV @ 1.0 Sec. nS TDEV @ 4.0 Sec. nS HCMOS OUTPUT CHARACTERISTICS TABLE 3.0 PARAMETER MINIMUM NOMINAL MAXIMUM UNITS NOTE LOAD pf Voltage (High) (Voh) 4.5 Vdc (Low) (Vol) 0.4 Vdc Current (High) (Ioh) mA (Low) (Ioh) mA Duty Cycle at 50% of Vcc Rise / Fall Time 10% to 90% nS PACKAGE CHARACTERISTICS TABLE 4.0 Package 14 pin DIP, hermetically sealed, grounded case, welded package Notes: 1) Initial calibration @ 25°C. 2) Overall frequency stability, 0 to 70°C. 3) Frequency stability per 5% change in supply voltage. 4) At the time of shipment after 48 hours of operation. 5) Inclusive of calibration, operating temperature range, supply voltage change, load change, shock and vibration, 10 years aging. 6) Measured @ 25°C, within 5 minutes, the unit will be within +/-0.1ppm of its reference frequency, measured after 30 minutes of continuous operation at a stable 25°C
THE CONNOR-WINFIELD CORP. 2111 COMPREHENSIVE DRIVE. AURORA, IL 60505. FAX (630) 851-5040. PHONE (630) 851-4722. P R O D U C T D A T A S H E E T Specifications subject to change without notice. DATA SHEET #: REV: DATE: PAGE OF Copyright 2001 Connor-Winfield all rights reserved. a CRYSTAL CONTROLLED OSCILLATORS Cx030 7/9/02 www.conwin.com ENVIRONMENTAL CHARACTERISTICS Temperature Cycle: Per MIL-STD-883, Method 1010, Condition B. -55°C to 125°C, 20 cycles,10 minute dwell, 1minute transition. Gross Leak Test: Per MIL-STD-202, Method 112, Condition D. No bubbles in flourinert (FC-43) at 125°C ±5°C for 20 seconds. SOLDERING Pin Solderability: Per MIL-STD-883, Method 200. 38 hour steam age prior to 254°C ±5°C Solder pot dip, 95% Coverage. Resistance to Solder Heat: Per MIL-STD-202, Method 210, Condition C. Wave: Topside board-mount product, 260°C ±5°C for 20 Seconds. MECHANICAL CHARACTERISTICS Vibration: Per MIL-STD-202, Method 204, Condition A. 10G’s peak, 10Hz to 500Hz, 15minute cycles 12 times each perpendicular axis. Shock: Per MIL-STD-202, Method 213, Condition D. 500G’s, 1ms, halfsine, 3 shocks per direction. Moisture Resistance: Per MIL-STD-202, Method 106. 95% RH @ 65°C, 10 cycles 10°C to 65°C.