DAX-25A

CDX-GT121 SONY | Alldatasheet

Document overview

• Manufacturer or author: Free Datasheet Search PDF
• PDF pages: 38

Technical content

Published by Sony Techno Create Corporation AEP Model UK Model 9-887-811-01 2007H04-1 © 2007. 08 Ver. 1.0 2007. 08 SPECIFICATIONS CD player section Signal-to-noise ratio 120 dB Frequency response 10 – 20,000 Hz Wow and flutter Below measurable limit Tuner section FM Tuning range 87.5 – 108.0 MHz Antenna terminal External antenna connector Intermediate frequency 10.7 MHz/450 kHz Usable sensitivity 9 dBf Selectivity 75 dB at 400 kHz Signal-to-noise ratio 67 dB (stereo), 69 dB (mono) Harmonic distortion at 1 kHz 0.5% (stereo), 0.3% (mono) Separation 35 dB at 1 kHz Frequency response 30 – 15,000 Hz MW/LW Tuning range MW: 531 – 1,602 kHz LW: 153 – 279 kHz Antenna (aerial) terminal External antenna (aerial) connector Intermediate frequency 10.7 MHz/450 kHz Sensitivity MW: 30 µV , LW: 40 µV Power amplifier section Outputs Speaker outputs (sure seal connectors) Speaker impedance 4 – 8 ohms Maximum power output

45 W × 4 (at 4 ohms)

Output Audio outputs terminal (sub/rear switchable) Power antenna (aerial) relay control terminal Power amplifier control terminal Inputs Telephone ATT control terminal Antenna (aerial) input terminal AUX input jack (stereo mini jack) Tone controls Low: ±10 dB at 60 Hz (XPLOD) Mid: ±10 dB at 1 kHz (XPLOD) High: ±10 dB at 10 kHz (XPLOD) Loudness +4 dB at 100 Hz +2 dB at 10 kHz

• The tuner and CD sections have no adjustments. Model Name Using Similar Mechanism NEW CD Drive Mechanism Type MG-101TC-188//Q Optical Pick-up Name DAX-25A – Continued on next page – FM/MW/LW COMPACT DISC PLAYER CDX-GT121/GT220/GT222 (Photo: CDX-GT220)

SAFETY -RELA TED COMPONENT W ARNING!! COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH MARK 0 ON THE SCHEMA TIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERA TION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE P ART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY. NOTES ON HANDLING THE OPTICAL PICK-UP BLOCK OR BASE UNIT The laser diode in the optical pick-up block may suffer electrostatic breakdown because of the potential difference generated by the charged electrostatic load, etc. on clothing and the human body. During repair, pay attention to electrostatic breakdown and also use the procedure in the printed matter which is included in the repair parts. The flexible board is easily damaged and should be handled with care. NOTES ON LASER DIODE EMISSION CHECK The laser beam on this model is concentrated so as to be focused on the disc reflective surface by the objective lens in the optical pick- up block. Therefore, w hen checking the laser diode emission, observe from more than 30 cm aw ay from the objective lens. If the optical pick-up block is defective, please replace the whole optical pick-up block. Ne ver turn the semi-fixed resistor located at the side of optical pick- up block. SER VICE NOTES CAUTION Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. Power requirements 12 V DC car battery (negative ground) Dimensions Approx. 178 × 50 × 179 mm Mounting dimensions Approx. 182 × 53 × 162 mm Mass Approx. 1.2 kg (2 lb. 11 oz.) Supplied accessoriesParts for installation and connections (1 set) Design and specifications are subject to change without notice. optical pick-up semi-fixed resistor Notes on Chip Component Replacement

• N ever reuse a disconnected chip component.
• N otice that the minus side of a tantalum capacitor may be damaged by heat. TEST DISCS Please use the following test discs for the check on the CD section. YDES-18 (Part No. 3-702-101-01) PATD-012 (Part No. 4-225-203-01)

• UNLEADED SOLDER Boards requiring use of unleaded solder are printed with the lead- free mark (LF) indicating the solder contains no lead. (Caution:Some printed circuit boards may not come printed with the lead free mark due to their particular size.) : LEAD FREE MARK Unleaded solder has the following characteristics.
• Unleaded solder melts at a temperature about 40°C higher than ordinary solder. Ordinary soldering irons can be used but the iron tip has to be applied to the solder joint for a slightly longer time. Soldering irons using a temperature regulator should be set to about 350°C. Caution:The printed pattern (copper foil) may peel aw ay if the heated tip is applied for too long, so be careful!
• Strong viscosity Unleaded solder is more viscous (sticky, less prone to flow) than ordinary solder so use caution not to let solder bridges occur such as on IC pins, etc.
• Usable with ordinary solder It is best to use only unleaded solder but unleaded solder may also be added to ordinary solder.
• CD Playback You can play CD-D A (also containing CD TEXT) and CD-R/ CD-R W (MP3/WMA f iles*). Type of discs Label on the disc CD-DA MP3 WMA * CDX-GT220/GT222 only TABLE OF CONTENTS 2. GENERAL 3. DISASSEMBL Y 5. DIAGRAMS 6. EXPLODED VIEWS This label is located on the bottom of the chassis. This compact disc player is classified as a CLASS 1 LASER product. The CLASS 1 LASER PRODUCT label is located on the exterior.

EXTENSION CABLE AND SER VICE POSITION When repairing or servicing this set, connect the jig (extension cable) as shown below .

• Connect the MAIN board (CNP301) and the SERV O board (CN2) with the extension cable (Part No. J-2502-076-1). NOTE FOR REPLACEMENT OF THE SER VO BOARD When repairing, the complete SERV O board (A-1177-201-A) should be replaced since any parts in the SERV O board cannot be repaired. NOTE FOR REPLACEMENT OF THE AUX JACK (J901) To replace the A UX jack requires alignment. 1. Insert the A UX jack into the KEY board. 2. Place the KEY board on the front panel. 3. Solder the three terminals of the jack. KEY board front panel AUX jack

• LOCATION OF CONTROL
• CONNECTIONS This section is extracted from instruction manual. Location of controls and basic operations Main unit This section contains instructions on the location of controls and basic operations. For details, see the respective pages. A OFF button To power off; stop the source. B EQ3 (equalizer) button page 10 To select an equalizer type (XPLOD, VOCAL, EDGE, CRUISE, SPACE, GRAVITY, CUSTOM or OFF). C Volume control dial/select button page 10 To adjust volume (rotate); select setup items (press and rotate). D SOU RCE button To power on; change the source (Radio/CD/ AUX). E Disc slot Insert the disc (label side up), playback starts. F Display window G AU X inpu t jack page 11 To connect a portable audio device. H Z (eject) button To eject the disc. SEEK SEEK PAUSEREP SHUF EQ3 DSPL OFF AF/TA PTY PUSH SELECT 16 23 54 MODE SOURCE AUX qa qsq;9 qd qgqf 4 5 8673 I (front panel release) button page 4 J DSP L (display)/SCRL (scroll) button (CDX-GT 225C/GT222 /GT220) page 8 To change display items (press); scroll the display item (press and hold). DS PL (display) button (CDX -GT121) page 8 To change display items. K SE EK –/+ buttons CD: To skip tracks (press); skip tracks continuously (press, then press again within about 1 second and hold); reverse/fast- forward a track (press and hold). Radio: To tune in stations automatically (press); find a station manually (press and hold). L MOD E button page 8 To select the radio band (FM/MW/LW). M AF (Alternative Frequencies)/ TA (Traffic Announcement)/ PT Y (Program Type) button page 10 To set AF and TA (press); select PTY (press and hold) in RDS. N Number b uttons CD: (1)/(2): AL BM –/+ (during MP3/WMA playback) (CDX-GT 225C/GT22 2/GT220) To skip albums (press); skip albums continuously (press and hold). (3): RE P page 8 (4): SHUF page 8 (6): PAU SE To pause playback. To cancel, press again. Radio: To receive stored stations (press); store stations (press and hold). O Receptor for the card remote command er (CDX-GT225C/GT 222/ GT22 0 only) Connection example Anschlussbeispiel Exemple de raccordement Esempio di collegamento Voorbeeldaansluitingen

L R REAR/SUB AU D IO OUT REAR / SUB A UDIO OUT *2 REMOTE IN Positions 1, 2, 3, and 6 do not have pins. An Position 1, 2, 3 und 6 befi nden sich keine Stifte. Les positions 1, 2, 3 et 6 ne comportent pas de broches. Le posizioni 1, 2, 3 e 6 non hanno piedini. De posities 1, 2, 3 en 6 hebben geen pins. Yellow Gelb Jaune Giallo Geel continuous power supply permanente Stromver sorgung alimentation continue alimentazione continua continu voeding Red Rot Roug e Rosso Rood sw itched power supply geschaltete Stromver sorgung alimentation commutée alimentazione commutata geschakelde voeding Blue Blau Bleu Blu Blauw power antenna (aerial) control Motorantennensteuerung antenne électrique comando dell’antenna elettrica elektrische antenne Black Schwarz Noir Nero Zwart ground (earth) Masse masse terra aarding Negative polarity positions 2, 4, 6, and 8 have striped leads. An den negativ gepolten Positionen 2, 4, 6 und 8 befi nden sich gestreifte Adern. Les positions de polarité négative 2, 4, 6 et 8 sont dotées de cordons rayés. Le posizioni a polarità negativa 2, 4, 6 e 8 hanno cavi rigati. De posities voor negatieve polariteit (2, 4, 6 en 8) hebben gestreepte kabels.

1 Purple

Speaker, Rear, Right Lautsprecher hinten rechts Haut-parleur, arrière, droit Diffusore, posteriore, destro Luidspreker, achter, rechts

5 White

We iß Blanc Bianco Wit Speaker, Front, Left Lautsprecher vorne links Haut-parleur, avant, gauche Diffusore, anteriore, sinistro Luidspreker, voor, links Speaker, Rear, Right Lautsprecher hinten rechts Haut-parleur, arrière, droit Diffusore, posteriore, destro Luidspreker, achter, rechts Speaker, Front, Left Lautsprecher vorne links Haut-parleur, avant, gauche Diffusore, anteriore, sinistro Luidspreker, voor, links

3 Gray

Speaker, Front, Right Lautsprecher vorne rechts Haut-parleur, avant, droit Diffusore, anteriore, destro Luidspreker, voor, rechts

7 Green

Grün Vert Verde Groen Speaker, Rear, Left Lautsprecher hinten links Haut-parleur, arrière, gauche Diffusore, posteriore, sinistro Luidspreker, achter, links Speaker, Front, Right Lautsprecher vorne rechts Haut-parleur, avant, droit Diffusore, anteriore, destro Luidspreker, voor, rechts Speaker, Rear, Left Lautsprecher hinten links Haut-parleur, arrière, gauche Diffusore, posteriore, sinistro Luidspreker, achter, links ATT Fuse (10 A) Sicherung (10 A) Fusible (10 A) Fusibile (10 A) Zekering (10 A) Light blue Hellblau Bleu ciel Azzurro Lichtblauw from the car’s power connector vom Stromansc hluss des Fahrzeugs du connecteur d’alimentation de la voiture dal connettore di alimentazione dell’auto v an de autovoedingsaansluitingSee “Power connection diagram” on the reverse side for details. Näheres dazu fi nden Sie im „Stromansc hlussdiagramm“. Blättern Sie dazu bitte um. Voir le « Schéma de raccordement d’alimentation » au verso pour plus de détails. Per ulteriori informazioni, vedere “Diagramma dei collegamenti di alimentazione” che si trova sul retro. Zie "Voedingsaansluitschema" op de achterkant voor meer details. from the car’s speaker connector vom Lautsprecheranschluss des Fahrzeugs du connecteur de haut-parleur de la voiture dal connettore dei diffusori dell’auto v an de autoluidsprekeraansluiting *1 from car antenna (aerial) von Autoantenne de l’antenne de la voiture dall’antenna dell’auto van een auto-antenne CDX-GT225C *1 Note for the antenna (aerial) connecting If your car antenna (aerial) is an ISO (International Organization for Standardization) type, use the supplied adaptor 2 to connect it. First connect the car antenna (aerial) to the supplied adaptor, then connect it to the antenna (aerial) jack of the master unit. *2 AUDIO OUT can be switched SUB or REAR. For details, see the supplied Operating Instructions. *3 Insert with the cord upwards (CDX-GT225C only) *1 Hinweis zum Anschließen der Antenne W enn Ihre Autoantenne der ISO-Norm (Internationale Norm ungsgemeinschaft) entspricht, schließen Sie sie mithilfe des mitgelieferten Adapters 2 an. Verbinden Sie zuerst die Autoantenne mit dem mitgelieferten Adapter und verbinden Sie diesen dann mit der Antennenbuchse des Hauptgeräts. *2 AUDIO OUT kann zwischen SUB und REAR umgeschaltet werden. Näheres hierzu fi nden Sie in der Bedienungsanleitung. *3 Mit dem Kabel nach oben einsetzen (nur CDX-GT225C) *1 Remarque sur le raccordement de l’antenne Si votre antenne de voiture est de type ISO (Organisation internationale de normalisation), utilisez l’adaptateur fourni pour la raccorder. Raccordez d’abord l’antenne de voiture à l’adaptateur fourni et, ensuite, à la prise d’antenne de l’appareil principal. *2 AU DIO OUT peut être commuté sur SUB ou REAR. Pour obtenir plus de détails, reportez-vous au mode d’emploi. *3 nsérez avec le câble vers le haut (CDX- GT225C uniquement) *1 Nota per il collegamento dell’antenna Se l’antenna dell’auto è di tipo ISO (International Organization for Standardization), utilizzare l’adattatore in dotazione per collegar 2 la. Collegare prima l’antenna della macchina all’adattatore in dotazione, quindi collegarla alla presa dell’antenna dell’apparecchio principale. *2 AU DIO OUT può essere impostato su SUB o su REAR. Per ulteriori informazioni, consultare il manuale di istruzioni per l’uso. *3 Inserire con il cavo rivolto verso l’alto (solo CDX-GT225C) *1 Opmer king bij de antenne-aansluiting Indien uw auto is uitgerust met een antenne van het type ISO (International Organization for Standardization), moet u die aansluiten met behulp van de bijgeleverde adapter 2. Sluit eerst de auto-antenne aan op de bijgeleverde adapter en vervolgens de antennestekker op het hoofdtoestel. *2 AU DIO OUT kan worden ingesteld op SUB of REAR. Raadpleeg de gebruiksaanwijzing voor meer informatie. *3 Plaatsen met het snoer naar boven. (CDX-GT225C alleen) Aansluitschema A Naar het interface-snoer van een autotelefoon W aarschuwing Indien u een elektrische antenne heeft zonder relaiskast, kan het aansluiten van deze eenheid met de bijgeleverde voedingskabel 3 de antenne beschadigen. Opmerking en over de bedienings- en voedingskabels

• De bedieningskabel van de elektrische antenne (blauw) levert +12 V gelijkstroom wanneer u de tuner inschakelt of de AF (alternatieve frequenties) of TA (verkeersinformatie) functie activeert.
• W anneer uw auto is uitgerust met een FM/MW/LW -antenne in de achterruit/voorruit, moet u de bedieningskabel van de elektrische antenne (blauw) of de voedingskabel van de accessoires (rood) aansluiten op de voedingsingang van de bestaande antenneversterker. Raadpleeg uw dealer voor meer details.
• M et dit apparaat is het niet mogelijk een elektrische antenne zonder relaiskast te gebruiken. Instandhouden van het geheug en Zolang de gele voedingskabel is aangesloten, blijft de stroomvoorziening van het geheugen intact, ook wanneer de contactschakelaar van de auto wordt uitgeschakeld. Opmerking en betreffende het aansluiten van de luidsprekers
• Zorg dat het apparaat is uitgeschakeld, alvorens de luidsprekers aan te sluiten.
• G ebruik luidsprekers met een impedantie van 4 tot 8 Ohm en let op dat die het vermogen van de versterker kunnen verwerken. Als dit wordt verzuimd, kunnen de luidsprekers ernstig beschadigd raken.
• V erbind in geen geval de aansluitingen van de luidsprekers met het chassis van de auto en sluit de aansluitingen van de rechter- en linkerluidspreker niet op elkaar aan.
• V erbind de aarddraad van dit apparaat niet met de negatieve (–) aansluiting van de luidspreker.
• Probeer nooit de luidsprekers parallel aan te sluiten.
• S luit geen actieve luidsprekers (met ingebouwde versterkers) aan op de luidsprekeraansluiting van dit apparaat. Dit zal leiden tot beschadiging van de actieve luidsprekers. Sluit dus altijd uitsluitend luidsprekers zonder ingebouwde versterker aan.
• O m defecten te vermijden mag u de bestaande luidsprekerbedrading in uw auto niet gebruiken wanneer er een gemeenschappelijke negatieve (–) draad is voor de rechter- en linkerluidsprekers.
• V erbind de luidsprekerdraden niet met elkaar. Opmerking over aansluiten Als de luidspreker niet goed is aangesloten, wordt "FAILURE" in het display weergegeven. In dit geval moet u zorgen dat de luidspreker correct is aangesloten. Schémas de raccordement A Vers le cordon de liaison d’un téléphone de voiture Avertissement Si vous disposez d’une antenne électrique sans boîtier de relais, le branchement de cet appareil au moyen du câble d’alimentation fourni 3 risque d’endommager l’antenne. Remar ques sur les câbles de commande et d’alimentation
• Le câble de commande d’antenne (bleu) fournit du courant continu de +12 V lorsque vous mettez le tuner sous tension ou lorsque vous activez la fonction AF (fréquence alternative) ou TA (messages de radioguidage).
• Lorsque votre voiture est ÈquipÈe d’une antenne FM/MW (GO)/LW (PO) intégrée dans la vitre arrière/latérale, raccordez le câble de commande d’antenne (bleu) ou le câble d’alimentation des accessoires (rouge) à la borne d’alimentation de l’amplifi cateur d’antenne existant. Pour plus de détails, consultez votre revendeur.
• Une antenne électrique sans boîtier de relais ne peut pas être utilisée avec cet appareil. Raccordement pour la conservation de la mémoire Lorsque le câble d’alimentation jaune est connecté, le circuit de la mémoire est alimenté en permanence même si la clé de contact est en position d’arrê. Remar ques sur le raccordement des haut-parleurs
• Avant de raccorder les haut-parleurs, mettre l’appareil hors tension.
• Utiliser des haut-parleurs ayant une impédance de 4 à 8 ohms et une capacité adéquate sous peine de les endommager .
• Ne pas raccorder les bornes du système de haut-parleurs au châssis de la voiture et ne pas connecter les bornes du haut- parleur droit à celles du haut-parleur gauche.
• Ne pas raccorder le câble de mise à la masse de cet appareil à la borne négative (–) du haut-parleur.
• Ne pas tenter de raccorder les haut-parleurs en parallèle.
• Connecter uniquement des haut-parleurs passifs. La connexion de haut-parleurs actifs (avec des amplifi cateurs intégrés) aux bornes des haut-parleurs pourrait endommager l’appareil.
• Pour éviter tout dysfonctionnement, n’utilisez pas les câbles des haut-parleurs intégrés installés dans votre voiture si l’appareil dispose d’un câble négatif commun (–) pour les haut-parleurs droit et gauche.
• Ne raccordez pas entre eux les cordons des haut-parleurs de l’appareil. Remar que sur le raccordement Si les haut-parleurs ne sont pas raccordés correctement, le message « FAILURE » s’affi che. Dans ce cas, assurez-vous que les haut-parleurs sont raccordés correctement. Anschlussdiagramm A An Schnittstellenkabel eines Autotelefons W arnung Wenn Sie eine Motorantenne ohne Relaiskästchen verwenden, kann durch Anschließen dieses Geräts mit dem mitgelieferten Stromversorgungskabel 3 die Antenne beschädigt werden. Steuer- und Stromver sorgungsleitungen
• Die Motorantennen-Steuerleitung (blau) liefert +12 V Gleichstrom, wenn Sie den Tuner einschalten oder die AF- (Alternativfrequenzsuche) oder die TA-Funktion (Verkehrsdurchsagen) aktivieren.
• W enn das Fahrzeug mit einer in der Heck-/ Seitenfensterscheibe integrierten FM (UKW)/MW/LW - Antenne ausgestattet ist, schließen Sie die Motorantennen- Steuerleitung (blau) oder die Zubehörstromversorgungsleitung (rot) an den Stromversorgungsanschluss des vorhandenen Antennenverstärkers an. Näheres dazu erfahren Sie bei Ihrem Händler.
• Es kann nur eine Motorantenne mit Relaiskästchen angeschlossen werden. Stromver sorgung des Speichers W enn die gelbe Stromversorgungsleitung angeschlossen ist, wird der Speicher stets (auch bei ausgeschalteter Zündung) mit Strom versorgt. Hinweise zum Lautsprecheranschluss
• Schalten Sie das Gerät aus, bevor Sie die Lautsprecher anschließen.
• Verwenden Sie Lautsprecher mit einer Impedanz zwischen 4 und 8 Ohm und ausreichender Belastbarkeit. Ansonsten können die Lautsprecher beschädigt werden.
• Verbinden Sie die Lautsprecheranschlüsse nicht mit dem W agenchassis und verbinden Sie auch nicht die Anschlüsse des rechten mit denen des linken Lautsprechers.
• Verbinden Sie die Masseleitung dieses Geräts nicht mit dem negativen (–) Lautsprecheranschluss.
• Versuchen Sie nicht, Lautsprecher parallel anzuschließen.
• An die Lautsprecheranschlüsse dieses Geräts dürfen nur Passivlautsprecher angeschlossen werden. Schließen Sie keine Aktivlautsprecher (Lautsprecher mit eingebauten Verstärkern) an, da das Gerät sonst beschädigt werden könnte.
• Um F ehlfunktionen zu vermeiden, verwenden Sie nicht die im Fahrzeug installierten, integrierten Lautsprecherleitungen, w enn am Ende eine gemeinsame negative (–) Leitung für den rechten und den linken Lautsprecher verwendet wird.
• Verbinden Sie nicht die Lautsprecherkabel des Geräts miteinander. Hinweis zum Anschließen W enn die Lautsprecher nicht richtig angeschlossen sind, erscheint „FAILURE“ im Display. Vergewissern Sie sich in diesem Fa ll, dass die Lautsprecher richtig angeschlossen sind. Schema di collegamento A Al cavo interfaccia di un telefono per auto Avvertenza Quando si collega l’apparecchio con il cavo di alimentazione in dotazione 3, si potrebbe danneggiare l’antenna elettrica se questa non dispone di scatola a relè. Note sui cavi di controllo e di alimentazione
• Il cavo (blu) di controllo dell’antenna elettrica fornisce alimentazione pari a +12 V CC quando si attiva il sintonizzatore oppure la funzione TA (notiziario sul traffi co) o AF (frequenza alternativa).
• Se l’utomobile è dotata di antenna FM/MW/LW incorporata nel vetro posteriore/laterale, collegare il cavo (blu) di controllo dell’antenna elettrica o il cavo (rosso) di ingresso dell’alimentazione accessoria al terminale di alimentazione dell’amplifi catore di potenza dell’antenna esistente. Per ulteriori informazioni, consultare il proprio fornitore.
• Non è possibile usare un’antenna elettrica senza scatola a relè con questo apparecchio. Collegamento per la conservazione della memoria Quando il cavo di alimentazione giallo è collegato, viene sempre fornita alimentazione al circuito di memoria anche quando líinterruttore di accensione è spento. Note sul collegamento dei diffusori
• Prima di collegare i diffusori spegnere l’apparecchio.
• Usare diffusori di impedenza compresa tra 4 e 8 ohm e con capacità di potenza adeguata, altrimenti i diffusori potrebbero venir danneggiati.
• Non collegare i terminali del sistema diffusori al telaio dell’auto e non collegare i terminali del diffusore destro a quelli del diffusore sinistro.
• Non collegare il cavo di terra di questo apparecchio al terminale negativo (–) del diffusore.
• Non collegare i diffusori in parallelo.
• Assicurarsi di collegare soltanto diffusori passivi, poiché il collegamento di diffusori attivi, dotati di amplifi catori incorporati, ai terminali dei diffusori potrebbe danneggiare l’apparecchio.
• Per evitare problemi di funzionamento, non utilizzare i cavi dei diffusori incorporati installati nell’automobile se l’apparecchio condivide un cavo comune negativo (–) per i diffusori destro e sinistro.
• Non collegare fra loro i cavi dei diffusori dell’apparecchio. Nota sui collegamenti Se il diffusore non è collegato correttamente, “FAILURE” viene visualizzato nel display. In tal caso, accertarsi che il diffusore sia collegato correttamente. Connection diagram A To the interface cable of a car telephone W arning If you have a power antenna (aerial) without a relay box, connecting this unit with the supplied power supply lead may damage the antenna (aerial).3 Notes on the control and power supply leads
• The pow er antenna (aerial) control lead (blue) supplies +12 V DC when you turn on the tuner, or when you activate the AF (Alternative Frequency) or TA (Traffi c Announcement) function.
• When your car has built-in FM/MW/LW antenna (aerial) in the rear/side glass, connect the pow er antenna (aerial) control lead (blue) or the accessory pow er supply lead (red) to the pow er terminal of the existing antenna (aerial) booster. For details, consult your dealer.
• A pow er antenna (aerial) without a relay box cannot be used with this unit. Memor y hold connection When the yellow pow er supply lead is connected, pow er will always be supplied to the memory circuit even when the ignition switch is turned off. Notes on speaker connection
• Before connecting the speakers, turn the unit off.
• Use speakers with an impedance of 4 to 8 ohms, and with adequate pow er handling capacities to avoid its damage.
• Do not connect the speaker terminals to the car chassis, or connect the terminals of the right speakers with those of the left speaker.
• Do not connect the ground (earth) lead of this unit to the negative (–) terminal of the speaker.
• Do not attempt to connect the speakers in parallel.
• Connect only passive speakers. Connecting active speakers (with built-in amplifi ers) to the speaker terminals may damage the unit.
• To avoid a malfunction, do not use the built-in speaker leads installed in your car if the unit shares a common negative (–) lead for the right and left speakers.
• Do not connect the unitís speaker leads to each other. Note on connection If speaker is not connected correctly, “FAILURE” appears in the display. In this case, make sure the speaker is connected correctly.

Note: This set can be disassemble according to the following sequence. 3-1. SUB PANEL ASSY (Page 8) 3-2. CD MECHANISM BLOCK (Page 8) SET 3-3. MAIN BO ARD (Page 9) 3-5. CHASSIS (T) SUB ASSY (Page 10) 3-6. R OLLER ARM ASSY (Page 10) 3-7. CHASSIS (OP) ASSY (Page 11) 3-8. CHUCKING ARM SUB ASSY (Page 11) 3-9. SLED MO TOR ASSY (Page 12) 3-10.OPTICAL PICK-UP SECTION (Page 13) 3-11. OPTICAL PICK-UP (Page 13) 3-4. SER VO BO ARD (Page 9)

3-2. CD MECHANISM BLOCK Note: Follow the disassembly procedure in the numerical order given. 3-1. SUB P ANEL ASSY 2 two claws 3 two claws 4 sub panel assy 1 two screws (+PTT 2.6 × 6)

4 CNP301

(+PTT 2.6 × 6) 2 screw (+PTT 2.6 × 6) 5 two screws (+PTT 2.6 × 4) 6 bracket (CD)7 CD mechanism block

3-4. SER VO BOARD 3-3. MAIN BOARD

9 MAIN board

(+PTT 2.6 × 8) 1 three ground point screws (+PTT 2.6 × 6) 7 screw (+PTT 2.6 × 10) 8 heat sink 4 two screws (+P 2.6 × 8) 6 screw (+P 2.6 × 10) 5 two screws (+PTT 2.6 × 10)

5 SERVO board

(M 1.7 × 2.5) 2 toothed lock screw (M 1.7 × 2.5) 1 Remove the eleven solders. GRY YEL BLE ORG RED BLK RED WHT BLK RED WHT 4 optical pick-up (16 core) (CN1)

3-6. ROLLER ARM ASSY 3-5. CHASSIS (T) SUB ASSY 4 chassis (T) sub assy 3 claw 1 two precision screws (+P 1.7 × 2.2) 2 two precision screws (+P 1.7 × 2.2) 3 washer 4 gear (RA1) 5 roller arm assy 1 spring (RAL) 2 spring (RAR)

3-7. CHASSIS (OP) ASSY 7 coil spring (damper) (natural) 8 coil spring (damper) (blue) 6 chassis (OP) assy 1 tension spring (KF) 2 gear (LE1) 3 lever (D) 4 slider (R) 3-8. CHUCKING ARM SUB ASSY 3 chucking arm sub assy 1 spring Note: Have this portion receive the chassis. Note: Have this portion receive the chassis. Note: Be careful not to touch the turn table.

3-9. SLED MOT OR ASSY 3 sled motor assy sled motor assy 1 spring spring stand stand turn table 2 three serration screws (M 2 × 3) three serration screws (M 2 × 3) Note: Place the stand with care not to touch the turn table. Note: Never remove these parts since they were adjusted. Note for Assembly Note: Take care to prevent the chassis from being bent when tightening the three machine screws.

3-10.OPTICAL PICK-UP SECTION 3-11.OPTICAL PICK-UP 2 optical pick-up section Note: Be careful not to touch the lens and hologram terminal when removing the optical pick-up section. There is space at the end of the leaf spring (sub guide) to avoid contact with the slide. 1 pan tapping screw (M 1.4 × 2.5) 2 leaf spring (sub guide) 3 leaf spring (OP) 5 optical pick-up 4 lead screw assy Notes for Assembly Prevent the end of the leaf spring (sub guide) from being in contact with the OP slide base. Prevent the end of the leaf spring (sub guide) from being in contact with the OP slide base.

Description of the Diagnostics function: 1. Setting the Diag display mode W ith the power off, press the [4] button, [5] button, and [4] button on the set body or the remote control (for more than 2 seconds) in turn. 2. Canceling the Diag display mode During the Diag function mode, press the [OFF] button. 3. Initial display in the Diag display mode. Just when the Diag mode is entered, “reset count” is displayed. The display mode is switched by each rotation of M >/SEEK + or . m/SEEK – keys. 4. Contents of each display mode 4-1. Reset count display mode 4-2. Reset count by watchdog timer display mode 4-3. Number of connected units display mode The display mode is switched by each rotation of [2] or [1] keys during the number of connected units display mode. 4-4. Operating hours display mode Reset count display OFFSET/F AILURE error display CD error information display Operating hours display Number of connected units display Reset count by watchdog timer display 01 XX 02 XX

031 XXX

04 XXXX

(in hexadecimal format) Diag code 01: Reset count 01 XX Reset count (in hexadecimal format) Diag code 02: Number of resets by watchdog timer 02 XX Show the number of connected units for CD-C , MD-C and XM respectively from the rightmost (in hexadecimal format). Recency of information 1-3: 1 represents the latest. Diag code 03: Number of connected unit. No. of connected units history 1 (latest) display No . of connected units history 3 display No. of connected units history 2 display

032 XXX

033 XXX

(in hexadecimal format) Diag code 04: Operating hours

4-5. CD error information display mode 4-5-1. Error description 4-5-2. Disc type and operating hours The display mode is switched by each rotation of [2] or [1] keys during the CD error information display mode. 4-6. OFFSET/FAILURE error display mode The display mode is switched by each rotation of [2] or [1] keys during the OFFSET/FAILURE error display mode. Error description (in hexadecimal format) Recency of information 1-3: 1 represents the latest. Diag code 05: CD error information 051 XX Operating hours Recency of information 1-3: 1 represents the latest. Diag code 05: CD error information Disc type 051XXXXX CD error info history 1 (latest) Error description plus error details display CD error info history 3 Disc type plus operating hours display CD error info history 3 Error description plus error details display CD error info history 2 Disc type plus operating hours display CD error info history 2 Error description plus error details display CD error info history 1 (latest) Disc type plus operating hours display 051XXXXX 052 XX 052XXXXX 053 XX 053XXXXX 051 XX Operating hours Recency of information 1-3: 1 represents the latest. Diag code 06: OFFSET/FAILURE Error description (0: OFFSET , 1: FAILURE) 061XXXXX OFFSET/F AILURE error history 1 (latest)display OFFSET/FAILURE error history 3 display OFFSET/F AILURE error history 2display 062XXXXX 063XXXXX 061XXXXX Error information Indication Description 1X SERVO ERROR 3X LOADING ERROR 4X TRACK JUMP 5X TEXT ERROR FX MECHA ERROR Disc type Indication Disc type

0 MP3

1 WMA

2 AAC

8 CD/DA

F UNKNOWN

5-1. BLOCK DIAGRAM — MAIN SECTION — SECTION 5 DIAGRAMS

• Signal Path
• R-CH is omitted due to same as L-CH. 1,2 AU_LCH AU_RCH UNI_SO UNI_SI UNI_CLK Z_MUTE CD_ON CDM_ON SYS_RST EJECT_OK BUS_ON BU+3.3V A_ATT BU_IN D_+3.3V A_+3.3V BU_+3.3V DR_+6V R-CH R-CH R-CH R-CH R-CH SERVO +3.3V BU_+3.3V MECHA +6V R-CH

9 AUX-LCH

7 AUX-RCH

CD_ON98 CDM_ON99 RESET77 SYSRST88 BUSON BU +3.3V VOUT1 VDD 2 D512 D510 : MW/LW : CD PLAY : FM : AUX

1 ANT 4 TU-LCH

8 AUX GND

(ANTENNA) TU1 (TUNER UNIT) CNP301 CD MECHANISM UNIT (MG-101TC) I2C BUS CONTROLLED POWER AMP/MULTIPLE VOLTAGE REGULATOR IC750 SYSTEM CONTROL IC501 (1/2) RESET IC602 CN601

3 TU-RCH

6 CD-LCH

5 CD-RCH

R-CH (FRONT) R-CH (REAR) VOLATT BATT R-CH 13TU-SCL 14TU-SDA 6S-METER 5QUALITY 7TU-MUTE 16E2P-SCL 17E2P-SDA

39 VSM

38 QUALITY

10 VCC (+8.3V)

11 TU-VDD (TU+5V)

15 E2P-VDD

AUDIO +8.3V TU+5V B.U +3.3V

12 TU ATT

25 EEP_CKO

24 EEP_SIO

56 DAVN

OUT-FL– OUT-RL+ OUT-RL– R-CH ANT-REM 35VP 20VP1 6VP2 30AUDIO+8.3V SERVO+3.3V MECHA+6V 34PANEL+B TU+5V OUT-FR OUT-RR R-CH R-CH SUBOUT L SUBOUT R 28MUTE

4 SCL

AUDIO +8.3V SERVO+3.3V MECHA+6V PANEL+B

2 SDA

16 BEEP

22 STB

25 DIAG

AUDIO +8.3V SCL SDA I2C-SCL I2C-SDA I2C-SCL I2C-SDA I2C-SCL I2C-SDA I2C-SCL I2C-SDA VSM QUALITY 8TU–ATTIN 9RDS–OUT

53 QUALITY

30 RDS ON

33I2C_CKO 34I2C_SIO 9VOL ATT 86ATT 5BEEP 26AMPSTB 8DIAG 54BU IN

12 IN-FL FL+

FL– L J330 R RL+ RL– FR+ FR– RR+ RR– ANT-REM BATT ACC 25OUT-FL

11 IN-RL23OUT-RL

Q478,479 BATT 72ACC_IN BATTERY LEVEL CHECK Q580–582 ACCESSORY CHECK Q631 TU+5V REG Q1,D1 MUTE Q461 29AMP-REM 5 AMP-REM TEST AUDIO OUT REAR D479 D511 D580 D581 FU601 73TESTIN TEL–ATT74TELATT TELEPHONE ATTENATION CHECK Q651 37B.UP+B BU +3.3V B.U+3.3V BATT RDS DEMODULATOR IC51 11SCL 12SDA 15INTN 1VDDA 7VDDB BU+3.3V

16 MPX

RDS+3.3V SWITCH Q51 X51 8.664MHz

9 XTI

13 NSMASK

• Waveforms — MAIN Board — 5-2. BLOCK DIAGRAM — DISPLA Y SECTION — • NOTE FOR PRINTED WIRING BOARDS AND SCHEMA TIC DIAGRAMS THIS NOTE IS COMMON FOR PRINTED WIRING BOARDS AND SCHEMA TIC DIAGRAMS. (In addition to this, the necessary note is printed in each block.) For schematic diagrams. Note:
• All capacitors are in µF unless otherwise noted. (p: pF)

50 WV or less are not indicated except for electrolytics

and tantalums.

• All resistors are in Ω and 1/4 W or less unless otherwise specified.
• f : internal component.
• C : panel designation. For printed wiring boards. Note:
• X : parts extracted from the component side.
• Y : parts extracted from the conductor side.
• a : Through hole.
• : Pattern from the side which enables seeing. (The other layers' patterns are not indicated.)
• A : B+ Line.
• B : B– Line.
• H : adjustment for repair.
• V oltages and waveforms are dc with respect to ground under no-signal (detuned) conditions. no mark: FM () : MW/LW <> : CD PLA Y ∗ : Impossible to measure
• V oltages are taken with a VOM (Input impedance 10 MΩ). Voltage variations may be noted due to normal production tolerances.
• W aveforms are taken with a oscilloscope. Voltage variations may be noted due to normal production tolerances.
• Circled numbers refer to waveforms.
• Signal path. J : CD PLAY F : FM f : MW/LW L : AUX Caution: Pattern face side:Parts on the pattern face side seen from the (Side B) pattern face are indicated. Parts face side: Parts on the parts face side seen from the (Side A) parts face are indicated. Q C These are omitted EB E These are omitted CB C These are omitted BE KEY ACKNOWLEDGE SWITCH Q664 X502 32.768kHz SYSTEM CONTROL IC501 (2/2) DISPLAY CONTROL IC901 KEYIN1 CL CE LCD_SO LCD_CKO LCD_CE 64 3SIRCS OUT DIMMER KEYIN0

31 RE-IN0RE-0

AD_ON XIN XOUT X501 18.432MHz

83 OSCOUT

7 NOSE_SW

|DI LCD BACK LIGHT SWITCH Q932 DIMMER SWITCH Q931 LED931 PANEL+B KEY MATRIX LSW901–911, S901–904 (VOLUME) PUSH SELECT RE901 ROTARY ENCODER BACK LIGHT LCD BACK LIGHT LSW901–911, LED941,942, 944,945,951–953 KEY ILLUMINATE GT220/GT222 IR REMOTE CONTROL SIGNAL RECEIVER IC971 Note:The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. 0.7Vp-p 32.768kHz

1 IC501 ul (XOUT)

1.8Vp-p 18.432MHz

2 IC501 id (OSCOUT)

0.5 V/DIV, 20 µsec/DIV

0.5 V/DIV, 20 nsec/DIV

8.664MHz

3 IC51 9 (XTI)

0.5 V/DIV, 0.1 µsec/DIV

: Uses unleaded solder.5-3. PRINTED WIRING BOARD — MAIN SECTION — A B C D E F G H I J 23456789 1 0 11 12 13 14 A KEY BOARD CN901 L -1 -2 R (ANTENNA) (CHASSIS) (CHASSIS) AUDIO OUT REAR CD MECHANISM UNIT (MG-101TC) FU601 Q478 Q479 Q651 Q582 R509 R513 R514 C504 C508 C507 R510R511 R512 Q664R517 R524 R526 R527 R528 C413 Q22R29 C501 R503 R582 D580 R651 GT121 R653 R654 D651 R632 R634 R633 Q631 R636 Q580 R521 R522 R585 R584 D581 R583 R532 R531 JC753 C343 R674 R671 R672 R534 R756 C755 R752 R479 C770 R536 R535 C404 C405 C756 R537 FMB3 FMB4 C509 R504 R505 R673 R540 R541 C510 C512 C513 C514 C516 R544C53 C54 C55 C56 C57 C58 C59 C60 C62 R51 R52 R53R54 R56 R57 JC681 R550 R461 R451 C763 D719 R557 R563 R564 R551 C617 C764C765C751 C602 C12 C13 R59 Q51 R60 R61 R301 R302 C306 C308 C309 C310 FB604 R652 D609 R609 C771 R573 FB1 JC754JC755 R533 D512 IC602 D510 D511 R431 Q431 R432 R441 R442 C312 R561 R565 R567 R529 R570 R12 R13 C519 R502 R462 R452 R401 JC533 R601 D502 R519 GT220/GT222 GT220/GT222 GT121JC504 C774C775 R566 R543 R578 GT121 R539 R675 R676 R677 R679 D617 R661 R662 R663 R664 Q581 R506 R692 IC51 C776 R694 C435 C455 C465 C445 C442 C432 C452 C462 R690 R693 C769 D704 C522 C523 R559 C63C64 IC501 R153 R154 R155 IC401 R412 R481 R482 R472 D153 C154 C155 R151 R152L151 C618 C454C464 R413 R414 C750 Q471 R471 Q481 Q441 Q451 Q461 R572 R575 D479 D503 R542 R547 JC510 C550 R631 C601 TU1 X51 X502 X501 D757 D760 RED D601 D758 D754 D755D756 D762 L601 CNP301 CN601 X501 D753 D752D751 CN701 JW63 JW62 JW119 JW86 JW67 JW60 JW89 JW102 JW22 JW42 JW3 RED JW65 JW82 JW53JW51JW52 JW94 JW93 JW18 JW111 JW133 JW54 JW24 JW23 JW25 JW39 JW1 JW2 JW31 JW26 JW9 JW17 JW50JW56 JW99 JW45 JW115 JW117 JW109 JW141 JW27 C441 C431 C451 C461 C401 C754 C407 C406 C51 C631 C753 C758 C479 C302 C301 C305 C511 C503 C412 IC750 C481 C471 C151 C152 JW84 JW85 JW108 JW139 C623 C622 JW70JW71 JW20 J330 JW106 JW132JW131 JW19 D761 D759 JW32 JW35 JW38 JW46 JW55 JW57 JW59 JW61 JW137 JW142 JW138 C153 JW21JW5JW8JW6 JW4 JW44 JW10 JW92 JW88 JW96 JW97 JW95 JW40 JW69 JW101 JW100 JW105JW104 JW68 JW73 JW124JW127 JW80 JW121 JW122 JW103 JW130 JW129 JW91 JW114 JW123 JW83 JW135 JW98 JW74JW126JW76 JW14 JW15 JW16 JW90 JW34 JW78 JW79 JW7 JW120 JW29 JW72 JW118 JW30 JW28 JW75 JW49 JW48 JW140JW125 JW87 JW77 JW66 JW11JW12JW13 1-874-377- (21) (Page 24) D1 F-3 D153 I-2 D479 E-6 D502 H-7 D503 I-5 D510 G-8 D511 F-6 D512 H-8 D580 F-10 D581 F-10 D601 C-10 D609 D-8 D617 C-9 D651 C-8 D704 I-3 D719 I-4 D751 D-7 D752 D-7 D753 D-6 D754 D-7 D755 C-6 D756 C-6 D757 C-6 D758 C-6 D759 D-8 D760 D-8 D761 C-9 D762 D-9 IC51 G-2 IC401 E-3 IC501 H-6 IC602 I-9 IC750 B-6 Q1 F-2 Q22 E-2 Q51 G-2 Q431 C-4 Q441 C-4 Q451 C-4 Q461 D-4 Q471 C-3 Q478 E-6 Q479 E-6 Q481 C-3 Q580 F-10 Q581 I-10 Q582 I-10 Q631 G-9 Q651 D-8 Q664 I-7

• Semiconductor Location Ref. No. Location

5-4. SCHEMA TIC DIAGRAM — MAIN SECTION (1/4) —

• Refer to page 18 for Waveforms.
• Refer to page 26 for IC Block Diagrams. (Page 22) (Page 21) (Page 23)

5-5. SCHEMA TIC DIAGRAM — MAIN SECTION (2/4) — • Refer to page 26 for IC Block Diagrams. IC B/D C479 C602 C618C617 C432 C452 C442 C462 C755 C751 JC753 C771 C769 C764C765 C750 JC754 JC755 C775 C774 C435 C455 C445 C465 JW111 C601 R479 C753 R752 C758 C754 R652 C756Q478 Q479 R651 D601 C776 CN601 FU601 C763 C770 D479 D751 D752 D753 D754 D755 D756 D757 D758 D759 D760 D761 D762 D651 D617 L601 R609 IC750 (Page 20) (Page 23)(Page 22)

5-6. SCHEMA TIC DIAGRAM — MAIN SECTION (3/4) —

• Refer to page 18 for Waveforms.
• Refer to page 27 for IC Pin Description of IC501. (Page 20) (Page 21) (Page 23)

5-7. SCHEMA TIC DIAGRAM — MAIN SECTION (4/4) — R633 R632 R631 R634 R583 R582 C623 JW53 CN701 R153 R151 R152 C155 C154 R155 JW140 C622 JW52 R584 C631 C519 R601 C151 C152C153 R540 R541 JC681 R654 R653 Q582 R585 Q581 L151 R154 IC602 Q631 Q651 Q580 FB604 D580 D581 D704 D153 D609 D719 (Page 20)(Page 21) (Page 22) (Page 25)

5-8. PRINTED WIRING BOARD — KEY SECTION — : Uses unleaded solder. A B C D E F G H I 23456789 1 0 1 1 1 2 13 14 A MAIN BOARD CN701 137 LIQUID CRYSTAL DISPLAY PANEL IC971 OFF EQ3 LSW901 LSW904 SEEK– M > SEEK+ LSW903 DSPL/SCRL LED951–953 (RING ILLUMINATION) 3/REP 4/SHUF LSW909LSW908LSW907LSW905 AF/TA /PTY 2/ALBUM+ (GT220/GT222) (GT121) (GT220/GT222) (GT121) LSW906 1/ALBUM– 5 6/PAUSE LSW911LSW910 1-874-378- 1-874-378- (21) (21) PUSH SELECT (VOLUME) RE901 LED941, S901 AUX J901 Z LED942, S902 LED943 S902 LED931 S903 S901 LED942 LED953 LED951 LED952 LED944 LED945 R975 C971 GT220/GT222 R943 R948 R944 R905 R946 LCD901 R945 R902 R901 IC971 LSW910LSW909LSW908LSW907LSW906LSW905 LSW903 LSW902 LSW902 DSPL (GT220/GT222) (GT121) SOURCE LED944, S903 LSW904 LSW901 S904 LED941 LSW911 LED931 (LCD BACK LIGHT) C985 R979 R978 R977 R982 C986 R974 GT220/GT222 GT220/GT222 C983 D982 C984 R986R985R984 D981 R981 R987 C981 FB903 D993 R933 R931 R932 R903 Q932 R972 R904 R907 R947R908 R909 D998 R913 R949 R912 R911 R914 R952R950 D991 D994 R951 IC901 R910 CN901 R971 C987 R988 Q931 R934 R942 R941 R992 R953R954 R915 D903 D992 J901 RE901 MODE LED945, S904 34 5 (Page 19) IC901 G-8 IC971 D-14 LED931 C-13 LED941 B-13 LED942 A-1 LED944 B-4 Ref. No. Location D903 G-11 D981 H-10 D982 H-10 D991 G-11 D992 G-11 D993 G-11 D994 F-14

• Semiconductor Location Ref. No. Location LED945 C-4 LED951 B-3 LED952 C-4 LED953 C-3 Q931 G-10 Q932 G-10 Ref. No. Location

901(1/2) LSW 902(1/2) LSW 903(1/2) LSW 904(1/2) S904 LSW 905(1/2) LSW 906(1/2) LSW 907(1/2) LSW908(1/2) LSW909(1/2) LSW 910(1/2) LSW 911(1/2) LSW901(2/2) LSW902(2/2) LSW904(2/2) LSW905(2/2) LSW906(2/2) LSW907(2/2) LSW908(2/2) LSW909(2/2) LSW911(2/2) LSW910(2/2) LSW903(2/2) J901 R934 D998 R992 Q931 LED942 LED941 R941 R942 LED943 LED931 R944 R943 R946 LED945 LED944 R945 R947 R948 R949 R950 R952 R951 R953 R954 R972 LED953 LED952 LED951 R971 R975 IC971 C971 D982 IC901 R974 RE901 D981 D994 D903 D991 D992 D993 5-9. SCHEMA TIC DIAGRAM — KEY SECTION — (Page 23)

• IC Block Diagrams IC401 BD3442FS-E2 (MAIN Board (1/4)) IC750 TDA8589BJ/N2/R1/M5 (MAIN Board (2/4)) MUTEMUTE ENABLE LOGIC STANDBY/ MUTE BATTERY DETECTION CHIP DETECT/ DIAGNOSTIC PROTECTION/ DIAGNOSTIC SWITCH REGULATOR SWITCH REFERENCE VOLTAGE LOADDUMP PROTECTION TEMPERATURE PROTECTION BACK-UP SWITCHREGULATOR TAB OUT-FL- OUT-FL+ OUT-RL- OUT-RL+ IN-RL S-GND IN-RR OUT-RR+ OUT-RR- OUT-FR+ OUT-FR- DIAG ANT-REM AMP-REM SERVO5V MECH6V VP B.UP+B SDA SCL VP2 PGND3 SVR IN-FL IN-FR BEEP PGND2 VP1 STB PGND1 RST CRES AUDIO8.3V GND PANEL+B CBU FL RL RR VP FR I C BUS BUS-L 100k 100k 100k 100k 100k 100k 250k 250k 250k BUS-R TU-L 3 4TU-R 5CD-L 6CD-R 7AUX-L 8AUX-G 9AUX-R 10DS32 11DS11 12DS22 13EBIAS 14DS21 15DS11 16DS31

26 OUTF1

27 VCCVCC

28 MUTE

29 SCL

30 SDA

31 GND

32 FIL

/MUTE VOLUME2 I2C BUS LOGIC TREBLE /BASS /MIDDLE SPECTRUM ANALYZER FADER

25 OUTF2

24 OUT-R1

23 OUT-R2

22 OUTS1

IC51 TDA7333013TR (MAIN Board (1/4)) VDDA INTERPOLATOR RAM BUFFER CONTROL LOGIC TEST LOGIC PIN MUX'S I C/SPI INTERFACE BAND PASS FILTER SIGMA DELTA CONVERTER SINC4 FILTER REF3 REF2 REF1 VSS VDDD RESETN TM MPX16 CSN SDAOUT RDSREG INTN MPX SINC4REG SDAIN SCK SPI TESTREG INTN15 SA13 SDA12 SCL11 OSCILLATOR XTO10 XTI9 RDS DEMODULATOR & SYNCHRONIZATION

• IC PIN DESCRIPTIONS
• IC501 MB90F045PF-G-9065-SPE2 (SYSTEM CONTROL) (MAIN BOARD (3/4)) Pin No. Pin Name I/O Pin Description

1 AREASEL0 I

Destination function setting pin 0

2 AREASEL1 I Destination function setting pin 1

3 AREASEL2 I Destination function setting pin 2

4 AREASEL3 I Destination function setting pin 3

5 BEEP O BEEP signal output to power amplifier

6 CYRIL_SEL I Cyril correspondence discrimination signal input “L”: No correspondence

7 NOSE_SW I Front panel attachment detect signal input “L”: Panel on, “H”: Panel off

8 DIAG I Status signal input from power amplifier

9 VOLA TT O Electronic volume attenuate control signal output

10 NCO O Not used. (Open)

11 VSS — Ground pin

12 TU ATT O Tuner mute control signal output

13 NSMASK O Noise mask signal output

14 to 22 NCO O Not used. (Open) 23 VCC5 — Power supply pin (+3.3V)

24 EEP_SIO I/O EEPROM bus serial data signal input/output

25 EEP_CKO O EEPROM bus serial clock signal output

26 AMPSTB O Stand-by signal output to power requlation

27 LCD_CE O Chip enable signal output to LCD driver

28 LCD_SO O Serial data signal output to LCD driver

29 LCD_CKO O Serial clock signal output to LCD driver

30 RDS ON O RDS (radio data system) ON signal output

31 RE-IN0 I Rotary encoder signal input 0

32 RE-IN1 I Rotary encoder signal input 1

33 I2C _C KO O I2C bus serial clock signal output

34 I2C_SIO I/O I2C bus serial data signal input/output

35 DA VDD — A/D converter power supply pin (+3.3V) 36 AVRH — A/D converter external reference power supply pin (+3.3V)

37 DA VSS — A/D converter Ground pin

38 QUALITY I Noise detect signal input

39 VSM I S-meter voltage detect signal input

40 KEYIN1 I Key signal input 1

41 KEYIN0 I Key signal input 0

42 VSS — Ground pin

43 RC_IN0 I Rotary commander key signal input Not used in this set. (Pull up) 44 to 48 NCO O Not used. (Open)

49 MD0 I Operation mode setting pin 0 (Pull up)

50 MD1 I Operation mode setting pin 1 (Pull up)

51 MD2 I Operation mode setting pin 2 (Pull down)

52 KEYAC K I Key acknowledgment detect signal input

53 TU_A TTIN I Tuner mute zero cross detect signal input

54 BUIN I Back-up power supply detect signal input

55 NCO O Not used. (Open)

56 DA VN I RDS data block synchronized detect signal input

57 NCO O Not used. (Open)

58 UNISI I S-BUS data signal input

59 UNISO O S-BUS data signal output

60 UNISCK O S-BUS clock signal output

61 CODEC_SEL I MP3 select signal input “H”: MP3, “L”: Non-MP3

62 ILLUMI SEL I Illumination voltage setting signal input “H”: 10.4 V, “L”: 9.0 V 63 NCO O Not used. (Open)

64 SIRCS I Remote control signal input

65 to 67 NCO O Not used. (Open) 68 FLASH_W I Memory mode select signal input Not used in this set. (Pull up) Normally “H” input: Single chip mode, after reset “L”: Flash write mode 69, 70 NCO O Not used. (Open) 71 RC_IN1 I Rotary commander shift key signal input Not used in this set. (Pull up)

72 AC C _IN I Accessory power supply detect signal input

73 TESTIN I Test mode detect signal input

74 TELA TT I Telephone attenuate detect signal input

75 NCO O Not used. (Open)

76 AD_ON O A/D converter power supply control signal output

77 RESET I System reset signal input

78 NCO O Not used. (Open) 79 XOUT O Low speed operation clock signal output (32.768 kHz) 80 XIN I Low speed operation clock signal input (32.768 kHz)

81 VSS1 — Ground pin

82 OSCIN I High speed operation clock signal input (18.432 MHz) 83 OSCOUT O High speed operation clock signal output (18.432 MHz) 84 VCC3 — Power supply pin (+3.3 V)

85 DEMOSEL I DEMO select signal input “H”: DEMO on, “L”: DEMO off

86 ATT O Audio mute control signal output

87 BUSON O BUS ON signal output

88 SYSRST O System reset signal output

89 to 92 NCO O Not used. (Open)

93 Z-MUTE I CD zero cross mute detect signal input

94 B OUT SEL I Black out with/without discrimination select signal input “H”: Black out

95 INI RS I REAR/SUB INITIAL setting signal input “H”: REAR INITIAL, “L”: SUB INITIAL

96 MO-DISP I Motion display signal input “H”: Motion display on, “L”: Motion display off

97 DIM_SEL I Dimmer select signal input “H”: Dimmer, “L”: No dimmer

Not used in this set. (Pull down)

98 CD_ON I CD mechanism servo power supply control request signal input

99 CDM_ON I CD mechanism deck power supply control request signal input

100 COL_SW I Illumination color select signal input Not used in this set. (Pull down) “H”: Two colors selection/initial slave, amber, “L”: Color/slave, amber Pin No. Pin Name I/O Pin Description

1 X-2186-975-1 PANEL ASSY, SUB

23 -042-244-11 SCREW (T)

3 X-2108-670-1 LOCK ASSY (S)

43 -376-464-11 SCREW (+PTT 2.6X6), GROUND POINT

5 A-1313-874-A MAIN BOARD, COMPLETE (GT220/GT222)

5 A-1313-999-A MAIN BOARD, COMPLETE (GT121)

62 -021-848-01 SHEET (TU), GROUND 71 -831-838-11 CORD (WITH CONNECTOR) (ISO) (POWER) FU601 1-532-877-11 FUSE (BLADE TYPE) (AUTO FUSE) 10A TU1 A-3220-961-B TUNER UNIT (TUX-032) #1 7-685-792-09 SCREW +PTT 2.6X6 (S) #2 7-685-790-01 SCREW +PTT 2.6X4 (S) #3 7-685-793-09 SCREW +PTT 2.6X8 (S) #4 7-685-794-09 SCREW +PTT 2.6X10 (S) #5 7-685-134-19 SCREW +P 2.6X8 TYPE2 NON-SLIT #6 7-621-284-40 SCREW +P 2.6X10 NOTE:

• The mechanical parts with no reference number in the exploded views are not supplied.
• Items marked “*” are not stocked since they are seldom required for routine service. Some delay should be anticipated when ordering these items.
• -XX and -X mean standardized parts, so they may have some difference from the original one.
• Color Indication of Appearance Parts Example : KNOB, B ALANCE (WHITE) ... (RED) Parts Color Cabinet’s Color
• Accessories are given in the last of this parts list. 6-1. MAIN SECTION RR The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. not supplied not supplied FU601 not supplied TU1 not supplied not supplied MG-101TC-188//Q A A B B A not supplied

51 A-1313-876-A PANEL COMPLETE ASSY, FRONT (GT220)

51 A-1313-970-A PANEL COMPLETE ASSY, FRONT (GT222)

51 A-1314-001-A PANEL COMPLETE ASSY, FRONT (GT121)

52 X-2179-451-1 BUTTON ASSY (S)

53 3-251-320-01 EMBLEM (NO. 2.5), SONY

54 X-2179-388-1 PANEL SUB ASSY, FRONT (GT121)

54 X-2179-389-1 PANEL SUB ASSY, FRONT (GT220)

54 X-2179-465-1 PANEL SUB ASSY, FRONT (GT222)

55 X-2179-452-1 KNOB (VOL) (SV) ASSY (GT220/GT222)

55 X-2186-464-1 KNOB (VOL) (SV) ASSY (GT121)

56 2-639-881-01 SPRING (RELEASE) 57 1-780-533-21 CONDUCTIVE BOARD, CONNECTION 58 3-214-259-11 ILLUMINATOR (LCD) 59 3-214-246-01 PANEL, BACK 60 3-250-543-21 SCREW (+B P-TITE M2)

61 X-2149-228-2 CASE ASSY (for FRONT PANEL)

(GT220/GT222) J901 1-820-624-11 SMALL TYPE JACK (VERTICAL) (AUX) LCD901 1-802-511-11 DISPLAY PANEL, LIQUID CRYSTAL RE901 1-479-902-21 ENCODER, ROTARY (PUSH SELECT/VOLUME) 6-2. FRONT P ANEL SECTION LCD901 not supplied not supplied not supplied not supplied (KEY board) not supplied not supplied not supplied not supplied RE901 J901

101 A-1289-450-A MECHANICAL BLOCK ASSY (08)

102 A-1284-705-A DAXEV08//Q

0103 X-2149-672-1 SERVICE ASSY, OP (DAX-25A)

104 2-626-869-01 SCREW (M2X3), SERRATION 105 3-348-998-31 SCREW (M1.4X2.5), TAPPING, PAN 106 3-352-758-31 SCREW (M1.7X2.5), TOOTHED LOCK

107 A-1177-201-A SERVO BOARD, COMPLETE

#7 7-627-000-08 SCREW, PRECISION +P 1.7X2.2 TYPE 3 6-3. CD MECHANISM SECTION (MG-101TC-188//Q) not supplied #7 #7 not supplied not supplied not supplied not supplied not supplied not supplied not supplied not supplied not supplied not supplied 101 102 103 105 104 107 106 106

1-780-533-21 CONDUCTIVE BOARD, CONNECTION 3-214-259-11 ILLUMINATOR (LCD) < CAPACITOR > C971 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V (GT220/GT222) C981 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V C983 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V C984 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V C986 1-125-891-11 CERAMIC CHIP 0.47uF 10% 10V C987 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V < CONNECTOR > CN901 1-819-758-12 PLUG, CONNECTOR 15P < DIODE > D903 6-501-782-01 DIODE MAZ8180GMLS0 D981 6-501-730-01 DIODE MAZ8051GMLS0 D982 8-719-988-61 DIODE 1SS355TE-17 D991 6-501-743-01 DIODE MAZ8068GMLS0 D992 6-501-743-01 DIODE MAZ8068GMLS0 D993 6-501-743-01 DIODE MAZ8068GMLS0 D994 6-501-743-01 DIODE MAZ8068GMLS0 (GT220/GT222) D998 1-216-295-11 SHORT CHIP 0 < JUMPER RESISTOR > FB903 1-216-295-11 SHORT CHIP 0 < IC > IC901 6-710-047-01 IC LC75836WH-US-E IC971 6-600-629-01 IC RS-470 (IR) (GT220/GT222) < JACK > J901 1-820-624-11 SMALL TYPE JACK (VERTICAL) (AUX) < LIQUID CRYSTAL DISPLAY > LCD901 1-802-511-11 DISPLAY PANEL, LIQUID CRYSTAL < DIODE > LED931 6-501-339-01 LED NESW505CT-AST (LCD BACK LIGHT) LED941 8-719-053-09 LED SML-310VTT86 (Z) LED942 8-719-053-09 LED SML-310VTT86 (OFF) LED943 1-216-864-11 SHORT CHIP 0 LED944 8-719-053-09 LED SML-310VTT86 (SOURCE) LED945 8-719-053-09 LED SML-310VTT86 (MODE) LED951 8-719-053-09 LED SML-310VTT86 (RING ILLUMINATION) LED952 8-719-053-09 LED SML-310VTT86 (RING ILLUMINATION) LED953 8-719-053-09 LED SML-310VTT86 (RING ILLUMINATION) < SWITCH > LSW901 1-786-805-12 SWITCH, TACTILE (WITH LED) (EQ3) LSW902 1-786-805-12 SWITCH, TACTILE (WITH LED) (DSPL) (GT121) LSW902 1-786-805-12 SWITCH, TACTILE (WITH LED) (DSPL/SCRL) (GT220/GT222) LSW903 1-786-805-12 SWITCH, TACTILE (WITH LED) (M > SEEK+) LSW904 1-786-805-12 SWITCH, TACTILE (WITH LED) (. m SEEK–) LSW905 1-786-805-12 SWITCH, TACTILE (WITH LED) (AF/TA/PTY) LSW906 1-786-805-12 SWITCH, TACTILE (WITH LED) (1) (GT121) LSW906 1-786-805-12 SWITCH, TACTILE (WITH LED) (1/ALBUM–) (GT220/GT222) LSW907 1-786-805-12 SWITCH, TACTILE (WITH LED) (2) (GT121) LSW907 1-786-805-12 SWITCH, TACTILE (WITH LED) (2/ALBUM+) (GT220/GT222) LSW908 1-786-805-12 SWITCH, TACTILE (WITH LED) (3/REP) LSW909 1-786-805-12 SWITCH, TACTILE (WITH LED) (4/SHUF) LSW910 1-786-805-12 SWITCH, TACTILE (WITH LED) (5) LSW911 1-786-805-12 SWITCH, TACTILE (WITH LED) (6/PAUSE) < TRANSISTOR > Q931 8-729-027-44 TRANSISTOR DTC114TKA-T146 Q932 6-551-444-01 TRANSISTOR RT1N436C-TP-1 < RESISTOR > R901 1-216-820-11 METAL CHIP 820 5% 1/10W R902 1-216-821-11 METAL CHIP 1K 5% 1/10W R903 1-216-821-11 METAL CHIP 1K 5% 1/10W R904 1-216-822-11 METAL CHIP 1.2K 5% 1/10W R905 1-216-823-11 METAL CHIP 1.5K 5% 1/10W R907 1-216-820-11 METAL CHIP 820 5% 1/10W R908 1-216-821-11 METAL CHIP 1K 5% 1/10W R909 1-216-821-11 METAL CHIP 1K 5% 1/10W R910 1-216-822-11 METAL CHIP 1.2K 5% 1/10W R911 1-216-823-11 METAL CHIP 1.5K 5% 1/10W NOTE:

• Due to standardization, replacements in the parts list may be different from the parts specified in the diagrams or the components used on the set.
• -XX and -X mean standardized parts, so they may have some difference from the original one.
• RESIST ORS All resistors are in ohms. MET AL:Metal-film resistor. MET AL O XIDE: Metal oxide-film resistor. F:nonflammable
• Items marked “*” are not stocked since they are seldom required for routine service. Some delay should be anticipated when ordering these items.
• SEMICONDUCT ORS In each case, u : µ, for example:
• CAP A CITORS uF : µF
• COILS uH : µH The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. When indicating parts by reference n umber, please include the board. KEY

R912 1-216-824-11 METAL CHIP 1.8K 5% 1/10W R913 1-216-825-11 METAL CHIP 2.2K 5% 1/10W R914 1-216-827-11 METAL CHIP 3.3K 5% 1/10W R915 1-216-828-11 METAL CHIP 3.9K 5% 1/10W R931 1-216-812-11 METAL CHIP 180 5% 1/10W R932 1-216-812-11 METAL CHIP 180 5% 1/10W R933 1-216-812-11 METAL CHIP 180 5% 1/10W R934 1-216-822-11 METAL CHIP 1.2K 5% 1/10W R941 1-216-813-11 METAL CHIP 220 5% 1/10W R942 1-216-813-11 METAL CHIP 220 5% 1/10W R943 1-216-812-11 METAL CHIP 180 5% 1/10W R944 1-216-811-11 METAL CHIP 150 5% 1/10W R945 1-216-812-11 METAL CHIP 180 5% 1/10W R946 1-216-811-11 METAL CHIP 150 5% 1/10W R947 1-216-812-11 METAL CHIP 180 5% 1/10W R948 1-216-811-11 METAL CHIP 150 5% 1/10W R949 1-216-809-11 METAL CHIP 100 5% 1/10W R950 1-216-809-11 METAL CHIP 100 5% 1/10W R951 1-216-812-11 METAL CHIP 180 5% 1/10W R952 1-216-811-11 METAL CHIP 150 5% 1/10W R953 1-216-812-11 METAL CHIP 180 5% 1/10W R954 1-216-811-11 METAL CHIP 150 5% 1/10W R971 1-216-809-11 METAL CHIP 100 5% 1/10W R972 1-216-809-11 METAL CHIP 100 5% 1/10W R974 1-216-809-11 METAL CHIP 100 5% 1/10W (GT220/GT222) R975 1-216-809-11 METAL CHIP 100 5% 1/10W (GT220/GT222) R977 1-216-809-11 METAL CHIP 100 5% 1/10W R978 1-216-809-11 METAL CHIP 100 5% 1/10W R979 1-216-809-11 METAL CHIP 100 5% 1/10W R981 1-216-811-11 METAL CHIP 150 5% 1/10W R982 1-216-811-11 METAL CHIP 150 5% 1/10W R984 1-216-821-11 METAL CHIP 1K 5% 1/10W R985 1-216-821-11 METAL CHIP 1K 5% 1/10W R986 1-216-821-11 METAL CHIP 1K 5% 1/10W R987 1-216-857-11 METAL CHIP 1M 5% 1/10W R988 1-216-840-11 METAL CHIP 39K 5% 1/10W R992 1-216-864-11 SHORT CHIP 0 < ROTARY ENCODER > RE901 1-479-902-21 ENCODER, ROTARY (PUSH SELECT/VOLUME) < SWITCH > S901 1-786-653-11 SWITCH, TACTILE (Z) S902 1-786-653-11 SWITCH, TACTILE (OFF) S903 1-786-653-11 SWITCH, TACTILE (SOURCE) S904 1-786-653-11 SWITCH, TACTILE (MODE) A-1313-874-A MAIN BOARD, COMPLETE (GT220/GT222) A-1313-999-A MAIN BOARD, COMPLETE (GT121) 7-621-284-40 SCREW +P 2.6X10 7-685-134-19 SCREW +P 2.6X8 TYPE2 NON-SLIT 7-685-794-09 SCREW +PTT 2.6X10 (S) < CAPACITOR > C1 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V C2 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V C3 1-126-963-11 ELECT 4.7uF 20% 50V C4 1-126-947-11 ELECT 47uF 20% 35V C5 1-126-947-11 ELECT 47uF 20% 35V C6 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V C7 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V C12 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V C13 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V C51 1-126-947-11 ELECT 47uF 20% 35V C53 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V C54 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V C55 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V C56 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V C57 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V C58 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V C59 1-164-237-11 CERAMIC CHIP 16PF 5% 50V C60 1-162-917-11 CERAMIC CHIP 15PF 5% 50V C62 1-162-959-11 CERAMIC CHIP 330PF 5% 50V C63 1-162-923-11 CERAMIC CHIP 47PF 5% 50V C64 1-162-923-11 CERAMIC CHIP 47PF 5% 50V C151 1-126-960-11 ELECT 1uF 20% 50V C152 1-126-960-11 ELECT 1uF 20% 50V C153 1-126-961-11 ELECT 2.2uF 20% 50V C154 1-163-017-00 CERAMIC CHIP 0.0047uF 10% 50V C155 1-163-017-00 CERAMIC CHIP 0.0047uF 10% 50V C301 1-124-248-00 ELECT 22uF 20% 25V C302 1-124-584-00 ELECT 100uF 20% 10V C305 1-124-584-00 ELECT 100uF 20% 10V C306 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V C308 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V C309 1-162-966-11 CERAMIC CHIP 0.0022uF 10% 50V C310 1-162-966-11 CERAMIC CHIP 0.0022uF 10% 50V C312 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V C343 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V C401 1-126-964-11 ELECT 10uF 20% 50V C404 1-127-715-11 CERAMIC CHIP 0.22uF 10% 16V C405 1-127-715-11 CERAMIC CHIP 0.22uF 10% 16V C406 1-126-160-11 ELECT 1uF 20% 50V C407 1-126-160-11 ELECT 1uF 20% 50V C412 1-104-665-11 ELECT 100uF 20% 25V C413 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V C431 1-126-964-11 ELECT 10uF 20% 50V C432 1-165-908-11 CERAMIC CHIP 1uF 10% 10V C435 1-165-908-11 CERAMIC CHIP 1uF 10% 10V C441 1-126-964-11 ELECT 10uF 20% 50V C442 1-165-908-11 CERAMIC CHIP 1uF 10% 10V C445 1-165-908-11 CERAMIC CHIP 1uF 10% 10V C451 1-126-964-11 ELECT 10uF 20% 50V C452 1-165-908-11 CERAMIC CHIP 1uF 10% 10V MAINKEY

C454 1-163-251-11 CERAMIC CHIP 100PF 5% 50V C455 1-165-908-11 CERAMIC CHIP 1uF 10% 10V C461 1-126-964-11 ELECT 10uF 20% 50V C462 1-165-908-11 CERAMIC CHIP 1uF 10% 10V C464 1-163-251-11 CERAMIC CHIP 100PF 5% 50V C465 1-165-908-11 CERAMIC CHIP 1uF 10% 10V C471 1-126-964-11 ELECT 10uF 20% 50V C479 1-124-589-11 ELECT 47uF 20% 16V C481 1-126-964-11 ELECT 10uF 20% 50V C501 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V C503 1-124-584-00 ELECT 100uF 20% 10V C504 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V C507 1-162-917-11 CERAMIC CHIP 15PF 5% 50V C508 1-162-916-11 CERAMIC CHIP 12PF 5% 50V C509 1-162-966-11 CERAMIC CHIP 0.0022uF 10% 50V C510 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V C511 1-124-584-00 ELECT 100uF 20% 10V C512 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V C513 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V C514 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V C516 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V C519 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V C522 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V C523 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V C550 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V C601 1-112-302-11 ELECT 3300uF 20% 16V C602 1-165-319-11 CERAMIC CHIP 0.1uF 50V C617 1-163-009-11 CERAMIC CHIP 0.001uF 10% 50V C618 1-163-009-11 CERAMIC CHIP 0.001uF 10% 50V C622 1-126-926-11 ELECT 1000uF 20% 10V C623 1-126-926-11 ELECT 1000uF 20% 10V C631 1-126-160-11 ELECT 1uF 20% 50V C750 1-115-340-11 CERAMIC CHIP 0.22uF 10% 25V C751 1-115-340-11 CERAMIC CHIP 0.22uF 10% 25V C753 1-128-551-11 ELECT 22uF 20% 63V C754 1-124-257-00 ELECT 2.2uF 20% 50V C755 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V C756 1-216-864-11 SHORT CHIP 0 C758 1-124-261-00 ELECT 10uF 20% 50V C763 1-127-715-11 CERAMIC CHIP 0.22uF 10% 16V C764 1-115-340-11 CERAMIC CHIP 0.22uF 10% 25V C765 1-115-340-11 CERAMIC CHIP 0.22uF 10% 25V C769 1-127-715-11 CERAMIC CHIP 0.22uF 10% 16V C770 1-127-715-11 CERAMIC CHIP 0.22uF 10% 16V C771 1-127-715-11 CERAMIC CHIP 0.22uF 10% 16V C774 1-115-340-11 CERAMIC CHIP 0.22uF 10% 25V C775 1-115-340-11 CERAMIC CHIP 0.22uF 10% 25V C776 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V < CONNECTOR > CN601 1-774-701-21 PIN, CONNECTOR 16P CN701 1-819-773-13 SOCKET, CONNECTOR 15P CNP301 1-820-611-11 CONNECTOR, BOARD TO BOARD 28P < DIODE > D1 6-501-734-01 DIODE MAZ8056GMLS0 D153 6-501-743-01 DIODE MAZ8068GMLS0 D479 8-719-988-61 DIODE 1SS355TE-17 D502 6-502-131-01 DIODE LRB751V-40T1G (GT220/GT222) D503 8-719-988-61 DIODE 1SS355TE-17 D510 6-501-656-01 DIODE LBAT54ALT1G D511 6-500-335-01 DIODE MC2838-T112-1 D512 6-501-654-01 DIODE LBAT54CLT1G D580 6-501-747-01 DIODE MAZ8075GMLS0 D581 6-501-782-01 DIODE MAZ8180GMLS0 D601 6-501-571-01 DIODE 1N5404-C311-3 D609 6-501-743-01 DIODE MAZ8068GMLS0 (GT121) D617 6-501-782-01 DIODE MAZ8180GMLS0 D651 6-501-782-01 DIODE MAZ8180GMLS0 D704 6-501-743-01 DIODE MAZ8068GMLS0 D719 6-501-782-01 DIODE MAZ8180GMLS0 D751 6-500-522-01 DIODE 10EDB40-TA1B2 D752 6-500-522-01 DIODE 10EDB40-TA1B2 D753 6-500-522-01 DIODE 10EDB40-TA1B2 D754 6-500-522-01 DIODE 10EDB40-TA1B2 D755 6-500-522-01 DIODE 10EDB40-TA1B2 D756 6-500-522-01 DIODE 10EDB40-TA1B2 D757 6-500-522-01 DIODE 10EDB40-TA1B2 D758 6-500-522-01 DIODE 10EDB40-TA1B2 D759 6-500-522-01 DIODE 10EDB40-TA1B2 D760 6-500-522-01 DIODE 10EDB40-TA1B2 D761 6-500-522-01 DIODE 10EDB40-TA1B2 D762 6-500-522-01 DIODE 10EDB40-TA1B2 < FERRITE BEAD > FB1 1-500-245-11 INDUCTOR, FERRITE BEAD FB604 1-500-245-11 INDUCTOR, FERRITE BEAD < IC > IC51 6-803-747-01 IC TDA7333013TR IC401 6-710-065-01 IC BD3442FS-E2 IC501 6-807-750-01 IC MB90F045PF-G-9065-SPE1 IC602 6-709-458-01 IC XC61CN2802NR IC750 6-705-363-11 IC TDA8589BJ/N2/R1/M5 < JACK > J1 1-815-185-13 JACK (ANTENNA) J330 1-774-698-11 JACK, PIN 2P (AUDIO OUT REAR) < JUMPER RESISTOR > JC504 1-216-864-11 SHORT CHIP 0 JC510 1-216-864-11 SHORT CHIP 0 JC533 1-216-864-11 SHORT CHIP 0 JC681 1-216-864-11 SHORT CHIP 0 JC753 1-216-296-11 SHORT CHIP 0 JC754 1-216-296-11 SHORT CHIP 0 JC755 1-216-296-11 SHORT CHIP 0 < COIL > L1 1-469-844-11 INDUCTOR 2.2uH L151 1-216-295-11 SHORT CHIP 0 L601 1-456-617-11 COIL, CHOKE < TRANSISTOR > Q1 6-551-431-01 TRANSISTOR 2SC6027T100-QR Q22 8-729-038-28 TRANSISTOR RT1N441C-TP-1 MAIN

Q51 6-551-696-01 TRANSISTOR ISA1235AC1TP-1EF Q431 8-729-027-44 TRANSISTOR DTC114TKA-T146 Q441 8-729-027-44 TRANSISTOR DTC114TKA-T146 Q451 8-729-027-44 TRANSISTOR DTC114TKA-T146 Q461 8-729-027-44 TRANSISTOR DTC114TKA-T146 Q471 6-551-856-01 TRANSISTOR LTC614TKFP8T146 Q478 8-729-027-43 TRANSISTOR DTC114EKA-T146 Q479 8-729-027-23 TRANSISTOR DTA114EKA-T146 Q481 6-551-856-01 TRANSISTOR LTC614TKFP8T146 Q580 8-729-027-43 TRANSISTOR DTC114EKA-T146 Q581 8-729-038-28 TRANSISTOR RT1N441C-TP-1 Q582 8-729-620-07 TRANSISTOR 2SC3052EF-T1-LEF Q631 8-729-620-07 TRANSISTOR 2SC3052EF-T1-LEF Q651 8-729-620-07 TRANSISTOR 2SC3052EF-T1-LEF Q664 8-729-027-23 TRANSISTOR DTA114EKA-T146 < RESISTOR > R1 1-216-821-11 METAL CHIP 1K 5% 1/10W R2 1-414-595-11 INDUCTOR, FERRITE BEAD R3 1-414-595-11 INDUCTOR, FERRITE BEAD R4 1-216-839-11 METAL CHIP 33K 5% 1/10W R5 1-216-843-11 METAL CHIP 68K 5% 1/10W R6 1-216-839-11 METAL CHIP 33K 5% 1/10W R7 1-216-843-11 METAL CHIP 68K 5% 1/10W R8 1-216-839-11 METAL CHIP 33K 5% 1/10W R9 1-216-843-11 METAL CHIP 68K 5% 1/10W R12 1-414-595-11 INDUCTOR, FERRITE BEAD R13 1-414-595-11 INDUCTOR, FERRITE BEAD R29 1-216-809-11 METAL CHIP 100 5% 1/10W R51 1-216-797-11 METAL CHIP 10 5% 1/10W R52 1-216-803-11 METAL CHIP 33 5% 1/10W R53 1-414-595-11 INDUCTOR, FERRITE BEAD R54 1-216-845-11 METAL CHIP 100K 5% 1/10W R56 1-414-595-11 INDUCTOR, FERRITE BEAD R57 1-414-595-11 INDUCTOR, FERRITE BEAD R59 1-216-833-11 METAL CHIP 10K 5% 1/10W R60 1-216-833-11 METAL CHIP 10K 5% 1/10W R61 1-216-821-11 METAL CHIP 1K 5% 1/10W R151 1-216-817-11 METAL CHIP 470 5% 1/10W R152 1-216-817-11 METAL CHIP 470 5% 1/10W R153 1-216-834-11 METAL CHIP 12K 5% 1/10W R154 1-216-834-11 METAL CHIP 12K 5% 1/10W R155 1-216-825-11 METAL CHIP 2.2K 5% 1/10W R301 1-216-821-11 METAL CHIP 1K 5% 1/10W R302 1-216-821-11 METAL CHIP 1K 5% 1/10W R401 1-216-797-11 METAL CHIP 10 5% 1/10W R412 1-218-883-11 METAL CHIP 33K 0.5% 1/10W R413 1-216-864-11 SHORT CHIP 0 R414 1-216-864-11 SHORT CHIP 0 R431 1-216-821-11 METAL CHIP 1K 5% 1/10W R432 1-216-833-11 METAL CHIP 10K 5% 1/10W R441 1-216-821-11 METAL CHIP 1K 5% 1/10W R442 1-216-833-11 METAL CHIP 10K 5% 1/10W R451 1-216-821-11 METAL CHIP 1K 5% 1/10W R452 1-216-833-11 METAL CHIP 10K 5% 1/10W R461 1-216-821-11 METAL CHIP 1K 5% 1/10W R462 1-216-833-11 METAL CHIP 10K 5% 1/10W R471 1-216-813-11 METAL CHIP 220 5% 1/10W R472 1-216-833-11 METAL CHIP 10K 5% 1/10W R479 1-216-805-11 METAL CHIP 47 5% 1/10W R481 1-216-813-11 METAL CHIP 220 5% 1/10W R482 1-216-833-11 METAL CHIP 10K 5% 1/10W R502 1-216-821-11 METAL CHIP 1K 5% 1/10W R503 1-216-821-11 METAL CHIP 1K 5% 1/10W R504 1-218-871-11 METAL CHIP 10K 0.5% 1/10W R505 1-218-871-11 METAL CHIP 10K 0.5% 1/10W R506 1-216-845-11 METAL CHIP 100K 5% 1/10W R509 1-216-813-11 METAL CHIP 220 5% 1/10W R510 1-216-821-11 METAL CHIP 1K 5% 1/10W R511 1-216-821-11 METAL CHIP 1K 5% 1/10W R512 1-216-821-11 METAL CHIP 1K 5% 1/10W R513 1-216-845-11 METAL CHIP 100K 5% 1/10W R514 1-216-845-11 METAL CHIP 100K 5% 1/10W R517 1-216-841-11 METAL CHIP 47K 5% 1/10W R519 1-216-845-11 METAL CHIP 100K 5% 1/10W R521 1-216-825-11 METAL CHIP 2.2K 5% 1/10W R522 1-216-825-11 METAL CHIP 2.2K 5% 1/10W R524 1-216-845-11 METAL CHIP 100K 5% 1/10W R526 1-216-845-11 METAL CHIP 100K 5% 1/10W R527 1-216-845-11 METAL CHIP 100K 5% 1/10W R528 1-216-845-11 METAL CHIP 100K 5% 1/10W R529 1-216-821-11 METAL CHIP 1K 5% 1/10W R531 1-216-845-11 METAL CHIP 100K 5% 1/10W R532 1-216-845-11 METAL CHIP 100K 5% 1/10W R533 1-216-845-11 METAL CHIP 100K 5% 1/10W R534 1-216-833-11 METAL CHIP 10K 5% 1/10W R535 1-216-833-11 METAL CHIP 10K 5% 1/10W R536 1-216-833-11 METAL CHIP 10K 5% 1/10W R537 1-216-845-11 METAL CHIP 100K 5% 1/10W R539 1-216-845-11 METAL CHIP 100K 5% 1/10W R540 1-216-845-11 METAL CHIP 100K 5% 1/10W R541 1-216-845-11 METAL CHIP 100K 5% 1/10W R542 1-216-821-11 METAL CHIP 1K 5% 1/10W R543 1-216-821-11 METAL CHIP 1K 5% 1/10W R544 1-216-821-11 METAL CHIP 1K 5% 1/10W R547 1-216-821-11 METAL CHIP 1K 5% 1/10W R550 1-216-845-11 METAL CHIP 100K 5% 1/10W R551 1-216-845-11 METAL CHIP 100K 5% 1/10W R557 1-216-825-11 METAL CHIP 2.2K 5% 1/10W R559 1-216-845-11 METAL CHIP 100K 5% 1/10W R561 1-216-845-11 METAL CHIP 100K 5% 1/10W R563 1-216-845-11 METAL CHIP 100K 5% 1/10W R564 1-216-845-11 METAL CHIP 100K 5% 1/10W R565 1-216-845-11 METAL CHIP 100K 5% 1/10W R566 1-216-845-11 METAL CHIP 100K 5% 1/10W R567 1-216-845-11 METAL CHIP 100K 5% 1/10W R570 1-216-817-11 METAL CHIP 470 5% 1/10W R572 1-216-845-11 METAL CHIP 100K 5% 1/10W R573 1-216-845-11 METAL CHIP 100K 5% 1/10W R575 1-216-845-11 METAL CHIP 100K 5% 1/10W R578 1-216-821-11 METAL CHIP 1K 5% 1/10W R582 1-216-821-11 METAL CHIP 1K 5% 1/10W R583 1-216-821-11 METAL CHIP 1K 5% 1/10W R584 1-216-849-11 METAL CHIP 220K 5% 1/10W R585 1-216-849-11 METAL CHIP 220K 5% 1/10W R601 1-216-845-11 METAL CHIP 100K 5% 1/10W MAIN

R609 1-249-425-11 CARBON 4.7K 5% 1/4W (GT121) R631 1-249-425-11 CARBON 4.7K 5% 1/4W R632 1-216-841-11 METAL CHIP 47K 5% 1/10W R633 1-216-841-11 METAL CHIP 47K 5% 1/10W R634 1-216-829-11 METAL CHIP 4.7K 5% 1/10W R636 1-216-845-11 METAL CHIP 100K 5% 1/10W R651 1-216-821-11 METAL CHIP 1K 5% 1/10W R652 1-216-841-11 METAL CHIP 47K 5% 1/10W R653 1-216-833-11 METAL CHIP 10K 5% 1/10W R654 1-216-833-11 METAL CHIP 10K 5% 1/10W R661 1-216-821-11 METAL CHIP 1K 5% 1/10W R662 1-216-833-11 METAL CHIP 10K 5% 1/10W R663 1-216-821-11 METAL CHIP 1K 5% 1/10W R664 1-216-833-11 METAL CHIP 10K 5% 1/10W R671 1-216-809-11 METAL CHIP 100 5% 1/10W R672 1-216-809-11 METAL CHIP 100 5% 1/10W R673 1-218-871-11 METAL CHIP 10K 0.5% 1/10W R674 1-216-845-11 METAL CHIP 100K 5% 1/10W R675 1-216-821-11 METAL CHIP 1K 5% 1/10W R676 1-216-821-11 METAL CHIP 1K 5% 1/10W R677 1-216-821-11 METAL CHIP 1K 5% 1/10W R679 1-216-821-11 METAL CHIP 1K 5% 1/10W R690 1-216-845-11 METAL CHIP 100K 5% 1/10W R692 1-216-845-11 METAL CHIP 100K 5% 1/10W (GT220/GT222) R693 1-216-845-11 METAL CHIP 100K 5% 1/10W (GT121) R694 1-216-821-11 METAL CHIP 1K 5% 1/10W R752 1-216-811-11 METAL CHIP 150 5% 1/10W R756 1-216-841-11 METAL CHIP 47K 5% 1/10W < TUNER UNIT > TU1 A-3220-961-B TUNER UNIT (TUX-032) < VIBRATOR > X51 1-813-532-11 VIBRATOR, CRYSTAL (8.664MHz) X501 1-813-524-21 VIBRATOR, CERAMIC (18.432MHz) X502 1-767-317-11 VIBRATOR, CRYSTAL (32.768kHz) A-1177-201-A SERVO BOARD, COMPLETE MISCELLANEOUS 7 1-831-838-11 CORD (WITH CONNECTOR) (ISO) (POWER) FU601 1-532-877-11 FUSE (BLADE TYPE) (AUTO FUSE) 10A Ref. No. Part No. Description Remark MAIN SERVO ACCESSORIES 3-218-435-11 MANUAL, INSTRUCTION (ENGLISH,GERMAN, FRENCH,ITALIAN,DUTCH) 3-218-436-11 MANUAL, INSTRUCTION, INSTALL (ENGLISH, GERMAN,FRENCH,ITALIAN,DUTCH) X-2149-228-2 CASE ASSY (for FRONT PANEL) (GT220/GT222) PARTS FOR INSTALLATION AND CONNECTIONS

151 X-2187-305-1 FRAME ASSY, FITTING

153 3-246-471-01 KEY (FRAME)

154 X-3382-926-1 SCREW ASSY (BS), FITTING

156 1-465-459-31 ADAPTOR, ANTENNA 157 1-831-838-11 CORD (WITH CONNECTOR) (ISO) (POWER) Ref. No. Part No. Description Remark 151 154 152 156 157 153 × 2 155

Clicking the version allows you to jump to the revised page. Also, clicking the version at the top of the revised page allows you to jump to the next revised page. Ve r. Date Description of Revision 1.0 2007. 08 New