D200ERU MPD | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 2
Technical content
Key Features: 2W Output Power 4:1 Input Voltage Range 1,500 VDC Isolation Short Circuit Protected Miniature SIP Case Single & Dual Outputs 1.0 MH MTBF Industry Standard Pin-Out Low Low Cost!! D200ERU Low Cost, 4:1 Input Miniature, 2W SIP DC/DC Con vert ers Series Input Parameter Conditions Min. Typ. Max. Units Reverse Polarity Input Current 1.0 A Short Circuit Input Power 1,500 mW Output Parameter Conditions Min. Typ. Max. Units Output Voltage Accuracy ±1.0 ±3.0 % Output Voltage Balance ±1.0 ±2.0 % Line Regulation Vin = Min to Max ±0.2 ±0.75 % Load Regulation Iout = 10% to 100% ±0.5 ±1.5 % Ripple (20 MHz) See Note 1 15 30 mV P - P Noise (20 MHz) 50 150 mV P - P Output Power Protection 120 % Temperature Coeffi cient ±0.03 %/°C Output Short Circuit Continuous (Autorecovery) General Parameter Conditions Min. Typ. Max. Units Isolation Voltage 60 Seconds 1,500 VDC Isolation Resistance 500 VDC 1,000 MΩ Isolation Capacitance 100 kHz, 1V 65 pF Switching Frequency , Single Output Iout = 100% 100 650 kHz Switching Frequency , Dual Output Iout = 100% 200 400 kHz Environmental Parameter Conditions Min. Typ. Max. Units Operating Temperature Range Ambient -40 +25 +85 °C Storage Temperature Range -55 +125 °C Cooling Free Air Convection Humidity RH, Non-condensing 95 % Physical Case Material Non-Conductive Black Plastic (UL94-V0) Weight 0.24 Oz (7.0g) Reliability Specifi cations Parameter Conditions Min. Typ. Max. Units MTBF MIL HDBK 217F, 25°C, Gnd Benign 1.0 MHours Absolute Maximum Ratings Parameter Conditions Min. Typ. Max. Units Input Voltage Surge (1 Sec) 24 VDC Input -0.7 40.0 VDC48 VDC Input -0.7 80.0 Lead Temperature 1.5 mm From Case For 10 Sec 300 °C Internal Power Dissipation All Models 1,800 mW Caution: Exceeding Absolute Maximum Ratings may damage the module. These are not continuous operating ratings. MicroPower Direct
292 Page Street
Stoughton, MA 02072 USA T: (781) 344-8226 F: (781) 344-8481 E: sales@micropowerdirect.com W: www.micropowerdirect.com Electrical Specifi cations Specifi cations typical @ +25°C, nominal input voltage & rated output current, unless otherwise noted. Specifi cations subject to change without notice. RoHS Compliant
Input Output Effi ciency (%, Typ) Fuse Rating Slow-Blow (mA) Voltage (VDC) Current (mA) Voltage (VDC) Current (mA, Max) Current (mA, Min)Nominal Range Full-Load No-Load Pin Single Dual Pin Single Dual 1 -Vin -Vin 7 NC Common 2 +Vin +Vin 8 NC NC
3 Remote ON/OFF 9 -Vout -Vout
NC = No Connection Pin Connections Notes: 1. When measuring output ripple, it is recommended that an external ceramic capacitor (approx. 1 µF to 10 µF) be placed from the +Vout pin to the -Vout pin for single output units and from each output to common for dual output units. 2. These units should not be operated with a load under 10% of full load. Operation at no-load may cause damage to the unit. 3. These converters are specifi ed for operation without external compo- nents. However, in some applica- tions the addition of input/output capacitors will enhance stability and reduce output ripple. Recommended capacitor values are given at right. Output ripple on single output units may be further enhanced by using the CS terminal (single output units operated at 50% load or below should use this function). A low ESR capacitor is connected between the CS pin and the -Vout pin (the capcitor anode connected to the -Vout pin). Recommended capacitor values are given in the table at right. If not used, the CS pin should be left open. 4. Dual output units may be connected to provide a 10V, 24V or 30 VDC output. To do this, connect the load across the +Vout and -Vout outputs and fl oat the output com- mon. 5. The remote on/off control pin is referenced to the -Vin pin. Input current to the pin should be between 5 - 10 mA with a maximum of 20 mA. 6. It is recommended that a fuse be used on the input of a power supply for protection. See the Model Selection table above for the correct rating. Vin Input Capacitor Vout Output Capacitor
12 VDC 100 µF 5 VDC 47 µF
15 VDC 100 µF 9 VDC 47 µF
24 VDC 10 µF 12 VDC 47 µF
48 VDC 10 µF 15 VDC 47 µF
3.3 5 9 12 15 820 µF 660 µF 470 µF 330 µF 220 µF ±5 ±9 ±12 ±15 ±330 µF ±220 µF ±150 µF ±120 µF Min Max On <0.6 VDC to Open Circuit Off 2.7 VDC 15.0 VDC Mechanical Notes: All dimensions are typical in inch es (mm) Tolerance x.xx = ±0.01 (±0.25) Mechanic All dime TolerancMicroPower Direct www.micropowerdirect.com 292 Page Street Ste D Stoughton, MA 02072 TEL: (781) 344-8226 FAX: (781) 344-8481 E-Mail: sales@micropowerdirect.com Derating Curve Max. Capacitive Load