D200RU MPD | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 2

Technical content

Key Features:

  • 2W Output Power
  • 4:1 Input Voltage Range
  • 1,000 VDC Isolation
  • Short Circuit Protected
  • Miniature SIP Case
  • Single & Dual Outputs
  • 1.0 MH MTBF
  • Industry Standard Pin-Out D200RU Miniature SIP, 2W Ultra-Wide 4:1 Input DC/DC Con vert ers Series Input Parameter Conditions Min. Typ. Max. Units Input Filter Capacitor Filter Reverse Polarity Input Current 0.5 A Short Circuit Input Power 1,500 mW Output Parameter Conditions Min. Typ. Max. Units Output Voltage Accuracy ±1.0 ±2.0 % Output Voltage Balance ±1.0 ±2.0 % Line Regulation Vin = Min to Max ±0.3 ±0.5 % Load Regulation Iout = 25% to 100% ±0.5 ±0.75 % Ripple & Noise (20 MHz) (Note 1) 30 50 mV P - P Ripple & Noise (20 MHz) Over Line, Load & Temp. 75 mV P - P Ripple & Noise (20 MHz) 15 mV rms Output Power Protection 120 % Transient Response Time (Note 2) 25% Load Step Change 100 300 μSec Transient Response Deviation ±3.0 ±5.0 % Temperature Coeffi cient ±0.01 ±0.02 %/°C Output Short Circuit Continuous General Parameter Conditions Min. Typ. Max. Units Isolation Voltage 60 Seconds 1,000 VDC Isolation Test Voltage Flash Tested For 1 Sec 1,100 VDC Isolation Resistance 500 VDC 1,000 MΩ Isolation Capacitance 100 kHz, 1V 250 500 pF Switching Frequency 300 kHz Environmental Parameter Conditions Min. Typ. Max. Units Operating Temperature Range Ambient -40 +25 +65 °C Operating Temperature Range Case -40 +25 +65 °C Storage Temperature Range -55 +105 °C Cooling Free Air Convection Humidity RH, Non-condensing 95 % Physical Case Material Non-Conductive Black Plastic (UL94-V0) Weight 0.23 Oz (6.5g) Reliability Specifi cations Parameter Conditions Min. Typ. Max. Units MTBF MIL HDBK 217F, 25°C, Gnd Benign 1,000 kHours Absolute Maximum Ratings Parameter Conditions Min. Typ. Max. Units Input Voltage Surge (1 Sec) 24 VDC Input -0.7 50.0 VDC48 VDC Input -0.7 100.0 Lead Temperature 1.5 mm From Case For 10 Sec 260 °C Internal Power Dissipation All Models 2,500 mW Caution: Exceeding Absolute Maximum Ratings may damage the module. These are not continuous operating ratings. Electrical Specifi cations Specifi cations typical @ +25°C, nominal input voltage & rated output current, unless otherwise noted. Specifi cations subject to change without notice. MicroPower Direct

292 Page Street

Stoughton, MA 02072 USA T: (781) 344-8226 F: (781) 344-8481 E: sales@micropowerdirect.com W: www.micropowerdirect.com RoHS Compliant

Mechanical Notes:

  • All dimensions are typical in inch es (mm)
  • Tolerance x.xx = ±0.01 (±0.25) Notes: 1. When measuring output ripple, it is recommended that an external 0.47 μF ceramic capacitor be placed from the +Vout pin to the -Vout pin for single output units and from each output to common for dual output units. For noise sensitive applications, the use of 3.3 μF capacitors will reduce the output ripple. 2. Transient recovery is measured to within a 1% error band for a load step change of 75% to 100%. 3. Operation at no-load will not damage these units. However, they may not meet all specifi cations. 4. Dual output units may be connected to provide a 10 VDC, 24 VDC, or 30 VDC output. To do this, connect the load across the positive (+Vout) and negative (-Vout) outputs and fl oat the output com- mon. 5. The converter should be connected to a low ac-impedance source. An input source with a highly inductive impedance may affect the stability of the converter. In applications where the converter output loading is high and input power is supplied over long lines, it may be necessary to use a capacitor on the input to insure start- up. In this case, it is recommended that a low ESR (ESR <1.0Ω at 100 kHz) capacitor be mounted close to the converter. For all models, it is recommended a 1.5 μF be used. 6. The optional remote on/off control pin is referenced to the -Vin pin. The standby input current is typically 0.1 mA (0.2 ma maximum). 7. It is recommended that a fuse be used on the input of a power sup- ply for protection. See the table above for the correct rating. Model Number Input Output Refl ected Ripple Current (mA) Effi ciency (%, Typ) Fuse Rating Slow-Blow (mA) Voltage (VDC) Current (mA) Voltage (VDC) Current (mA, Max) Current (mA, Min)Nominal Range Full-Load No-Load Pin Single Dual 1 -Vin -Vin 2 +Vin +Vin

3 Remote ON/OFF

7 NC Common

NF = No Connection Pin Connections Output (VDC) μF Max 3.3 2,200 5.0 1,000 12.0 170 15.0 110 ±5.0 470 ±12.0 100 ±15.0 47 Note: For dual output units, Cap load is given for each output. Capacitive Load Min Max On <0.6 VDC to Open Circuit Off 2.7 VDC 15.0 VDC In. Current (on) -1 mA In. Current (off) 1 mA Derating Curve MicroPower Direct www.micropowerdirect.com 292 Page Street Ste D Stoughton, MA 02072 • TEL: (781) 344-8226 • FAX: (781) 344-8481 • E-Mail: sales@micropowerdirect.com