D200ED MPD | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 2
Technical content
Key Features: 2W Output Power Miniature SIP Case UL Approved (File E245422) Dual Isolated Outputs 1,000 VDC Isolation >3.5 MHour MTBF 12 Standard Models Industry Standard Pin-Out LOWEST COST!! D200ED Very Low Cost, 2W SIP Dual Isolated Output DC/DC Con vert ers Series Electrical Specifi cations Specifi cations typical @ +25°C, nominal input voltage & rated output current, unless otherwise noted. Specifi cations subject to change without notice. Input Parameter Conditions Min. Typ. Max. Units Input Voltage Range 5 VDC Input 4.5 5.0 5.5 VDC12 VDC Input 10.8 12.0 13.2 24 VDC Input 21.6 24.0 26.4 Input Filter Internal Capacitor Reverse Polarity Input Current 0.3 A Output Parameter Conditions Min. Typ. Max. Units Output Voltage Accuracy ±3.0 % Line Regulation For Vin Change of 1% ±1.2 % Load Regulation Iout = 10% to 100% ±15.0 Ripple (20 MHz) See Note 2 75 150 mV P - P Noise (20 MHz) See Note 2 150 250 mV P - P Output Power Protection 120 % Temperature Coeffi cient ±0.01 ±0.02 %/ºC Output Short Circuit Momentary (0.5 Sec.) General Parameter Conditions Min. Typ. Max. Units Isolation Voltage, Input/Output 60 Seconds 1,000 VDC Isolation Voltage, Output/Output 1,000 VDC Isolation Resistance 500 VDC 1,000 MΩ Isolation Capacitance 100 kHz, 1V 60 pF Switching Frequency 70 kHz Environmental Parameter Conditions Min. Typ. Max. Units Operating Temperature Range Ambient -40 +25 +85 ºC Storage Temperature Range -55 +125 ºC Cooling Free Air Convection Humidity RH, Non-condensing 95 % Physical Case Material Non-Conductive Black Plastic (UL94-V0) Weight 0.09 Oz (2.8g) Reliability Specifi cations Parameter Conditions Min. Typ. Max. Units MTBF MIL HDBK 217F, 25ºC, Gnd Benign 3.5 MHours Absolute Maximum Ratings Parameter Conditions Min. Typ. Max. Units Input Voltage Surge (1 Sec) 5 VDC Input -0.7 9.0 VDC12 VDC Input -0.7 18.0 24 VDC Input -0.7 30.0 Lead Temperature 1.5 mm From Case For 10 Sec 300 ºC Internal Power Dissipation All Models 450 mW Caution: Exceeding Absolute Maximum Ratings may damage the module. These are not continuous operating ratings. MicroPower Direct
292 Page Street
Stoughton, MA 02072 USA T: (781) 344-8226 F: (781) 344-8481 E: sales@micropowerdirect.com W: www.micropowerdirect.com RoHS Compliant
Notes: All dimensions are typical in inches (mm) Tolerance x.xx = ±0.01 (±0.25) Pin 1 is marked by a “dot” or indentation on the side of the unit Derating Curve g Notes: 1. Output load regulation is specifi ed for a load change of 10% to 100%. 2. When measuring output ripple, it is recommended that an external ceramic capacitor (approx approx 1 µF to 10 µF) be placed from each output to common. 3. These units should not be operated with a load under 10% of full load. Operation at no-load may cause damage to the unit. 4. These converters are specifi ed for operation without external components. However, in some applications the addition of input/ouput capacitors will enhance stability and reduce output ripple. Recommended capacitor values are: Vin Input Capacitor Vout Output Capacitor 5 VDC 4.7 µF 5 VDC 4.7 µF 12 VDC 2.2 µF 9 VDC 2.2 µF 24 VDC 1.0 µF 12 VDC 1.0 µF 15 VDC 0.47 µF For applications requiring very low output noise levels, a simple LC fi lter should be effective. 5. It is recommended that a fuse be used on the input of a power supply for protection. See the Model Selection table above for the correct rating. MicroPower Direct www.micropowerdirect.com 292 Page Street Ste D Stoughton, MA 02072 TEL: (781) 344-8226 FAX: (781) 344-8481 E-Mail: sales@micropowerdirect.com Model Selection Guide Mechanical Dimensions Pin Connections Model Number Input Output 1 Output 2 Effi ciency (%, Typ) Fuse Rating Slow-Blow (mA) Voltage (VDC) Current (mA) Voltage (VDC) Current (mA, Max) Current (mA, Min) Voltage (VDC) Current (mA, Max) Current (mA, Min)Nominal Range Full-Load No-Load Pin Function 1+ V i n 2- V i n 4 -Vout 1 5 +Vout 1 6 -Vout 2 7 +Vout 2 Block Diagram