D100ER MPD | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 2

Technical content

Key Features:

  • 1W Output Power
  • Tightly Regulated
  • Single & Dual Outputs
  • Miniature SIP Case
  • 1,000 VDC Isolation
  • >3.5 MHour MTBF
  • 24 Standard Models
  • Industry Standard Pin-Out
  • LOWEST COST!! D100ER Low Cost, 1W SIP Tightly Regulated DC/DC Con vert ers Series Input Parameter Conditions Min. Typ. Max. Units Input Voltage Range 5 VDC Input 4.75 5.0 5.25 VDC12 VDC Input 11.4 12.0 12.6 24 VDC Input 22.8 24.0 25.2 Input Filter Internal Capacitor Reverse Polarity Input Current 0.3 A Output Parameter Conditions Min. Typ. Max. Units Output Voltage Accuracy ±3.0 % Output Voltage Balance Dual Output , Balanced Loads ±0.1 ±1.0 % Line Regulation For Vin Min to Max ±0.25 % Load Regulation (Note 1) For Iout = 10% to 100% ±1.0 % Ripple & Noise (20 MHz) (Note 3) 10 20 mV P - P Output Power Protection 120 % Temperature Coeffi cient ±0.03 %/ºC Output Short Circuit Momentary (1.0 Sec.) General Parameter Conditions Min. Typ. Max. Units Isolation Voltage 60 Seconds 1,000 VDC Isolation Resistance 500 VDC 1,000 MΩ Isolation Capacitance 100 kHz, 1V 60 pF Switching Frequency 100 kHz Environmental Parameter Conditions Min. Typ. Max. Units Operating Temperature Range Ambient -40 +25 +85 ºC Operating Temperature Range Case -40 +90 ºC Storage Temperature Range -55 +125 ºC Cooling Free Air Convection Humidity RH, Non-condensing 95 % Physical Case Material Non-Conductive Black Plastic (UL94-V0) Weight 0.07 Oz (2.1g) Reliability Specifi cations Parameter Conditions Min. Typ. Max. Units MTBF MIL HDBK 217F, 25ºC, Gnd Benign 3.5 MHours Absolute Maximum Ratings Parameter Conditions Min. Typ. Max. Units Input Voltage Surge (1 Sec) 5 VDC Input -0.7 9.0 VDC12 VDC Input -0.7 18.0 24 VDC Input -0.7 30.0 Lead Temperature 1.5 mm From Case For 10 Sec 300 ºC Internal Power Dissipation All Models 450 mW Caution: Exceeding Absolute Maximum Ratings may damage the module. These are not continuous operating ratings. MicroPower Direct

292 Page Street

Stoughton, MA 02072 USA T: (781) 344-8226 F: (781) 344-8481 E: sales@micropowerdirect.com W: www.micropowerdirect.com RoHS Compliant Electrical Specifi cations Specifi cations typical @ +25°C, nominal input voltage & rated output current, unless otherwise noted. Specifi cations subject to change without notice.

Notes:

  • All dimensions are typical in inches (mm)
  • Tolerance x.xx = ±0.01 (±0.25)
  • Pin 1 is marked by a “dot” or indentation on the side of the unit Model Number Input Output Effi ciency (%, Typ) Fuse Rating Slow-Blow (mA) Voltage (VDC) Current (mA) Voltage (VDC) Current (mA, Max) Current (mA, Min)Nominal Range Full-Load No-Load Pin Single Dual 1 +Vin +Vin 2 -Vin -Vin 4 -Vout No Pin 6 +Vout No Pin

7 No Pin +Vout

9 No Pin -Vout

10 No Pin Common

Notes: 1. Output load regulation is specifi ed for a load change of 10% to 100%. 2. These units should not be operated with a load under 10% of full load. Operation at no-load may cause damage to the unit. 3. These converters will operate without external components. However, when measuring output ripple, it is recommended that an external ceramic capaci- tor be placed from the +Vout pin to the -Vout pin for single output units and from each output to common for dual output units. An input capacitor will enhace stability over temperature and input line variations. Recommended capaci- tor values are given in the table at right. For applications requir- ing very low output noise levels, a simple LC fi lter should be effective. 4. It is recommended that a fuse be used on the input of a power supply for protection. See the Model Selection table above for the correct rating. Vin Input Capacitor Vout Output Capacitor Single Dual 5 VDC 4.7 μF 5 VDC 10.0 μF 4.7 μF 12 VDC 2.2 μF 9 VDC 4.7 μF 2.2 μF 24 VDC 1.0 μF 12 VDC 2.2 μF 1.0 μF 15 VDC 1.0 μF 0.47 μF Model Selection Guide Mechanical Dimensions (Single Output) Pin Connections Mechanical Dimensions (Dual Output) Notes: All dimen Tolerance Pin 1 is ma on the sid MicroPower Direct www.micropowerdirect.com 292 Page Street, STE D, Stoughton, MA 02072 • TEL: (781) 344-8226 • FAX: (781) 344-8481 • E-Mail: sales@micropowerdirect.com