D100D MPD | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 2

Technical content

Key Features:

  • 1W Output Power
  • Miniature SIP Case
  • Dual Isolated Outputs
  • 1,000 VDC Isolation
  • >2 MHour MTBF
  • 24 Standard Models
  • Industry Standard Pin-Out MicroPower Direct

232 Tosca Drive

Stoughton, MA 02072 USA T: (781) 344-8226 F: (781) 344-8481 E: sales@micropowerdirect.com W: www.micropowerdirect.com D1 00D Miniature, 1W SIPMiniature, 1W SIP Dual Isolated OutputDual Isolated Output DC/DC Con vert ersDC/DC Con vert ers Series Electrical Specifi cations Specifi cations typical @ +25°C, nominal input voltage & rated output current, unless otherwise noted. Specifi cations subject to change without notice. Input Parameter Conditions Min. Typ. Max. Units Input Voltage Range 5 VDC Input 4.5 5.0 5.5 VDC12 VDC Input 10.8 12.0 13.2 24 VDC Input 21.6 24.0 26.4 48 VDC Input 43.2 48.0 52.8 Input Filter Internal Capacitor Reverse Polarity Input Current 0.3 A Output Parameter Conditions Min. Typ. Max. Units Output Voltage Accuracy ±3.0 % Line Regulation For Vin Change of 1% ±1.2 % Load Regulation Iout = 20% to 100% ±8.0 Ripple & Noise (20 MHz) See Note 2 75 mV P - P Output Power Protection 120 % Temperature Coeffi cient ±0.01 ±0.02 %/ºC Output Short Circuit Momentary (0.5 Sec.) General Parameter Conditions Min. Typ. Max. Units Isolation Voltage, Input/Output 60 Seconds 1,000 VDC Isolation Voltage, Output/Output 1,000 VDC Isolation Resistance 500 VDC 1,000 MΩ Isolation Capacitance 100 kHz, 1V 60 pF Switching Frequency 125 kHz Environmental Parameter Conditions Min. Typ. Max. Units Operating Temperature Range Ambient -40 +25 +85 ºC Operating Temperature Range Case -40 +90 ºC Storage Temperature Range -40 +125 ºC Cooling Free Air Convection Humidity RH, Non-condensing 95 % Physical Case Material Non-Conductive Black Plastic (UL94-V0) Weight 0.07 Oz (2.1g) Reliability Specifi cations Parameter Conditions Min. Typ. Max. Units MTBF MIL HDBK 217F, 25ºC, Gnd Benign 2.0 MHours Absolute Maximum Ratings Parameter Conditions Min. Typ. Max. Units Input Voltage Surge (1 Sec) 5 VDC Input -0.7 9.0 VDC12 VDC Input -0.7 18.0 24 VDC Input -0.7 30.0 48 VDC Input -0.7 55.0 Lead Temperature 1 .5 mm From Case For 10 Sec 260 ºC Internal Power Dissipation All Models 450 mW Caution: Exceeding Absolute Maximum Ratings may damage the module. These are not continuous operating ratings.

Notes: All dimensions are typical in inches (mm) Tolerance x.xx = ±0.01 (±0.25) Pin 1 is marked by a “dot” or indentation on the side of the unit For 5V, 12V & 24V input models, “W” = 0.24 in (6.0 mm) For 48V input models, “W” = 0.28 in (7.2 mm) Notes: 1. Output load regulation is specifi ed for a load change of 20% to 100%. 2. When measuring output ripple, it is recommended that an external ceramic capacitor (approx 10 µF) be placed across the output. 3. The 5V, 12V and 24V input units do not require external components to operate, but the use of an input capacitor (10 µF) may enhance performance in some applications. An output capacitor (1.0 µF to 10 µF) may be used to reduce ripple. The 48V input models require an input capacitor of 4.7 uF to 47 uF (dependent upon the application). 4. It is recommended that a fuse be used on the input of a power supply for protection. See the table above for the correct rating. Derating Curve -40 -10 0 5 15 25 35 45 55 65 75 85 95 105 100 Ambient Temperature 1C Output Power % 0.02 (0.50) 0.01 (0.25) 0.77 (19.5) 7612 0.08 (2.13) 0.10 (2.54) 0.37 (9.5) 0.12 (3.05) 0.05 (1.25) Bottom Side “W” 0.20 (5.08) 0.02 (0.50) 0.02 (0.50) MicroPower Direct www.micropowerdirect.com 232 Tosca Drive Stoughton, MA 02072 ■ TEL: (781) 344-8226 ■ FAX: (781) 344-8481 ■ E-Mail: sales@micropowerdirect.com Model Selection Guide Mechanical Dimensions Pin Connections Model Number Input Output 1 Output 2 Effi ciency (%, Typ) Fuse Rating Slow-Blow (mA) Voltage (VDC) Current (mA) Voltage (VDC) Current (mA, Max) Current (mA, Min) Voltage (VDC) Current (mA, Max) Current (mA, Min)Nominal Range Full-Load No-Load Pin Function 1+ V i n 2- V i n 4 +Vout 1 5 -Vout 1 6 +Vout 2 7 -Vout 2 Output 1 μF Max Output 2 μF Max 100 100 Capacitive Load T1+VIN -VIN Input Filter Switching Transistors Output Rectifier Filter Output Rectifier Filter Block Diagram