CXP84400 SONY | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 5

Technical content

Features

  • A wide instruction set (213 instructions) which cover various types of data. —16-bit operation/multiplication and division/boolean bit operation instructions
  • Minimum instruction cycle 400ns at 10MHz operation
  • Applicable EPROM LCC type 27C128, LCC type 27C256 (Maximum 16K bytes are available)
  • Incorporated RAM capacity 448bytes
  • Peripheral functions —A/D converter 8-bit, 8-channel, successive approximation method (Conversion time of 32µs/10MHz) —Serial interface Incorporated 8-bit, 8-stage FIFO (Auto transfer for 1 to 8 bytes), 1 circuit 2 channels —Timer 8-bit timer 8-bit timer/counter 19-bit time base timer 32kHz timer/counter —Remote control receiving circuit 8-bit pulse measurement counter with on-chip 6-stage FIFO —PWM output 14bits, 1channel
  • Interruption 12 factors, 12 vectors, multi-interruption possible
  • Standby mode SLEEP/STOP
  • Package 80-pin ceramic PQFP Note)Mask option depends on the type of the CXP84400. Refer to the Products List for details. Structure Silicon gate CMOS IC – 1 – CXP84400 E94X13-PS CMOS 8-bit Single Chip Microcomputer Sony reserves the right to change products and specifications without prior notice. This information does not convey any license by any implication or otherwise under any patents or other right. Application circuits shown, if any, are typical examples illustrating the operation of the devices. Sony cannot assume responsibility for any problems arising out of the use of these circuits. 80 pin PQFP (Ceramic) Piggyback/ evaluator type

– 2 – CXP84400 PF3 PF4 PF5 PF6 PF7 PD0 PD1 PD2 PD3 PD4 PD5 PD6 PD7 PC0 PC1 PC2 PC3 PC4 PC5 PC6 PC7 PH0 PH1 PH2 PI4 PI3/INT3 PI2/INT2 PI1/INT1 PI0/INT0 PE5/TO/ADJ PE4/PWM PE3/NMI PE2/RMC PE1 PE0/EC PB7/SO1 PB6/SI1 PB5/SCK1 PB4/SO0 PB3/SI0 PB2/SCK0 PB1/CS0 PB0/CS1 PA7/AN7 PA6/AN6 PA5/AN5 PA4/AN4 PA3/AN3 PH3 PH4 PH5 PH6 PH7 RST EXTALXTAL Vss TX TEX AVssAV REF PA0/AN0 PA1/AN1 PA2/AN2 PF2 PF1 PF0 PG7 PG6 PG5 PG4 NC V DD PG3 PG2 PG1 PG0 PI7 PI6 PI5 A11 NC OE A10 CE NC A7 A12 A15 NC V DD A14 A13 D1 D2 GND NC D3 D4 D5 25 26 27 28 29 30 4039383736353431 32 33 70 69 68 67 6566 71727374757677787980 234 14 15 16 17 18 19 20 3031321 Pin Assignment in Piggyback Mode Note)NC (Pin 73) is always connected to VDD .

– 3 – CXP84400 PF3 PF4 PF5 PF6 PF7 PD0 PD1 PD2 PD3 PD4 PD5 PD6 PD7 PC0 PC1 PC2 PC3 PC4 PC5 PC6 PC7 PH0 PH1 PH2 PI4 PI3/INT3 PI2/INT2 PI1/INT1 PI0/INT0 PE5/TO/ADJ PE4/PWM PE3/NMI PE2/RMC PE1 PE0/EC PB7/SO1 PB6/SI1 PB5/SCK1 PB4/SO0 PB3/SI0 PB2/SCK0 PB1/CS0 PB0/CS1 PA7/AN7 PA6/AN6 PA5/AN5 PA4/AN4 PA3/AN3 PH3 PH4 PH5 PH6 PH7 RST EXTALXTAL Vss TX TEX AVssAV REF PA0/AN0 PA1/AN1 PA2/AN2 PF2 PF1 PF0 PG7 PG6 PG5 PG4 NC V DD PG3 PG2 PG1 PG0 PI7 PI6 PI5 A11 NC HALT A10 E/P I/T MON A6/D6 A5/D5 A4/D4 A3/D3 A2/D2 A1/D1 A0/D0 NC RD A7/D7 A12 A15 NC V DD A14 A13 WR SYNCGND NC C2 C1 RST 25 26 27 28 29 30 4039383736353431 32 33 70 69 68 67 6566 71727374757677787980 234 14 15 16 17 18 19 20 3031321 Pin Assignment in Evaluator Mode Note)NC (Pin 73) is always connected to VDD .

– 4 – CXP84400 EPROM Read Timing (Ta = –20 to +75°C, VDD = 4.5 to 5.5V, VSS = 0V reference) Products List Mask product CXP84412 CXP84416 80-pin plastic QFP 12K bytes 16K bytes Existent/Non-existent Address fi data Input delay time Address fi data Hold time Item Symbol Pin Min. Max. Unit tACC tIH A0 to A15 D0 to D7 A0 to A15 D0 to D7 0 120 ns ns tACC tIH 0.8VDD 0.8VDD 0.2VDD 0.2VDD Input data Address dataA0 to A15 D0 to D7 Products Option item Package ROM capacity Pull-up resistor for reset pin Piggyback/evaluator product CXP84400-U01Q 80-pin ceramic PQFP EPROM 16K bytes Existent

– 5 – CXP84400 Package Outline Unit: mm Pin 1 index Pin 1 marking LCC type EPROM Pin 1 marking Piggyback mode Piggyback/evaluator product Evaluator mode CPU probe Note) Note) Evaluation cap should be connected to CPU probe. Piggyback mode/evaluator mode can be switched as shown below. SONY CODE EIAJ CODE JEDEC CODE PACKAGE STRUCTURE PACKAGE MATERIAL LEAD TREATMENT LEAD MATERIAL PACKAGE WEIGHT CERAMIC GOLD PLATING

42 ALLOY

5.7g PQFP-80C-L01 AQFP080-C-0000-A 80PIN PQFP (CERAMIC) 18.7 16.3 ± 0.2 9.48 11.66 15.58 ± 0.2 4025 6580 22.3 ± 0.25 4.5 6.0 24.7 1.27 ± 0.13 12.02 14.22 18.12 ± 0.2 0.3 PIN No. 1 INDEX INDEX

9.59 MAX

0.15 – 0.02 + 0.05 3.57 ± 0.36 PIN No. 1 INDEX 1.3 ± 0.3 1.0 0.7 41 65 80 2540 0.6