CXA2000

CXA2000Q SONY | Alldatasheet

Document overview

• Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
• PDF pages: 48

Technical content

Features

• I 2C bus compatible
• Compatible with both PAL and NTSC systems (also compatible with SECAM if a SECAM decoder is connected)
• Built-in deflection compensation circuit capable of supporting various wide modes
• Countdown system eliminates need for H and V oscillator frequency adjustment
• Automatic identification of 50/60Hz vertical frequency (forced control possible)
• Non-interlace display support (even/odd selectable)
• Automatic identification of PAL, NTSC, and SECAM color systems (forced control possible)
• Automatic identification of 4.43MHz/3.58MHz crystal (forced control possible)
• Non-adjusting Y/C block filter
• One CV input, one set of Y/C inputs, two sets of analog RGB inputs (one set of which can serve as both analog and digital inputs)
• Built-in AKB circuit
• Support for forcing YS1 off

Applications

Color TVs (4:3, 16:9) Structure Bipolar silicon monolithic IC Absolute Maximum Ratings (Ta = 25°C, SGND, DGND = 0V)

• Supply voltage SV CC 1, 2, DVCC 1, 2 –0.3 to 12 V
• Operating temperature Topr –20 to +65 °C
• Storage temperature Tstg –65 to +150 °C
• Allowable power dissipation PD 1.7 W (when mounted on 50mm · 50mm board)
• Voltages at each pin –0.3 to SV CC 1, SVCC 2, DV CC 1, DVCC 2 + 0.3 V Operating Conditions Supply voltage SV CC 1, 2 9.0 ± 0.5 V DV CC 1, 2 9.0 ± 0.5 V – 1 – CXA2000Q E96103-ST Y/C/RGB/D for PAL/NTSC Color TVs Sony reserves the right to change products and specifications without prior notice. This information does not convey any license by any implication or otherwise under any patents or other right. Application circuits shown, if any, are typical examples illustrating the operation of the devices. Sony cannot assume responsibility for any problems arising out of the use of these circuits. 64 pin QFP (Plastic)

– 2 – CXA2000Q Block Diagram S SEP VIDEO SW SHARP NESSSUB CONT TRAP KILLER DET ACC DET DL DC TRAN CLP D PIC WIDE Sawtooth Gen. AKB BLK CV/YC TRAP OFF DLSHARP DC TRAN D PICAGINGSTATUS VM OFF SUB COLOR TRAP F0 TOT ACC PRE/OVER TOT PAL ID PAL/ NTSC DEM APC HUE VCO DEM AXISIREF fsc ID COLOR SW fsc R-Y fsc B-Y V SYNC SEP H SYNC SEP 1Vp-p CVIN YIN CIN SV CC 1 SV CC 2 SGND1 SGND2 XTAL HUE IREF APCFIL X358 X443 FSCOUT SECAMREF –(R-Y) OUT –(B-Y) OUT YOUT YRET –(R-Y) IN –(B-Y) IN YS1 R1IN G1IN B1IN YS2 YM R2IN G2IN B2IN ABLFIL CUT OFF GB DRVBRT COL γ OSD MIXPICYS/YM SW Y/C MIX COLOR & AXIS COL CLP CLP DIG HV COMP ABL EHT H, V AKB OFF IKIN BOUT GOUT ROUT E-WOUT VD–OUT /VPROT VD+OUT /VPROT SAWOSC VAGCSH VTIM SCPOUT HD OUT DGND DV CC 2 DV CC 1 ABLIN/ VCOMP RSH GSH BSH L2FIL AFCPIN/ HOFF CERA AFCFIL HSIN VSIN VSFIL BLHOLD DCTRAN VM SCL SDA SYNCOUT EXT SYNC IN GB CUTGB DRVBRTγPIC WIDE Parabola Gen. VLIN, SCORR VPOSI, VOFF, VSIZE Count Down INTER -LACE D-COL GATE 50/60 ID GATE PHASE DET. 1/32 PHASE SHIFT PHASE DET 32fH VCO 2fH H POSI AFC C MODE INTERLACE V FREQ SCP BGR/BGF 40 39384145 46 4748 495051 525456 43 60 646162 1 3 4 5 6 7 8 11 12 13 14 15 16 17 18 19 21 23 252829 2Vp-p 1Vp-p EXT SYNC 6dB H.DRIVE YS1 OFF YS SW SUB CONT Sand Castle

– 3 – CXA2000Q Pin Configuration HSIN E-WOUTVSFIL L2FILIREF SAWOSCCERA HDOUTSDA VAGCSHVSIN AFCFILDV CC DV CC DGND AFCPIN/HOFFVMSCL SYNCOUT EXT SYNC IN TEST APCFIL X358 BLHOLD CIN NC SV CC 1 X443 DCTRAN CVIN YIN ABLIN/VCOMP BOUT SV CC 2 GOUT ROUT IKIN RSH BSH GSH VTIM VD–OUT/VPROT ABLFIL 40 39 38 37 364142434445464748495051 35 34 33 YOUT B2IN –(R-Y) IN G1IN SGND2 R2INYS1 YS2 SECAMREF G2INYRET R1IN –(B-Y) IN YM SCPOUT B1IN –(R-Y) OUT SGND1 –(B-Y) OUT 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 191 FSCOUT VD+OUT/VPROT

– 4 – CXA2000Q SECAM decoder interface. This pin serves as both a 4.43MHz output and as a SECAM identification input/output pin. Pin Description Pin No. Symbol Equivalent circuit Description

1 SECAMREF

–(R-Y) OUT –(B-Y) OUT Color difference signal outputs. Go to high impedance when the SECAM system is detected. Standard output levels for 75% CB: B-Y: 0.665Vp-p R-Y: 0.525Vp-p

5 YOUT

Luminance signal output. Black level is 3.5VDC. Standard output level for 100 IRE input: 1Vp-p

6 YRET

Luminance signal input. Clamped to 4.8V at the burst timing. Standard input level for 100 IRE input: 1Vp-p –(R-Y) IN –(B-Y) IN Color difference signal inputs. Clamped to 5.5V at the burst timing. Standard input levels for 75% CB: B-Y: 1.33Vp-p R-Y: 1.05Vp-p 2 SGND1 GND for Y/C block. 9 SGND2 GND for the RGB block. 250µA 6k 20p 7.2V 200µA 400µA 500 30k 1.5k 70k 8 1.5k 70k

– 5 – CXA2000Q YSSW control input. When YS is high, the RGB1 block signal is selected; when YS is low, the Y/C block is selected. This function can be disabled by the YS1OFF setting for the I 2C bus. VILMAX = 0.4V VIHMIN = 1.0V

10 SCPOUT

Sand castle pulse output. The 0 to 5V BGP pulse, the phase of which is controlled through the bus, is superimposed with the 0 to 2V H and VBLK pulse for output.

11 YS1

Analog R, G and B signal inputs. Input a 0.7Vp-p (no sync, 100 IRE) signal via a capacitor. The signal is clamped to 5.7V at the burst timing of the signal input to the HSIN input pin (Pin 47).

15 YS2

YS/YMSW YS control input. When YS is high, the RGB2 block signal is selected; when YS is low, the YSSW output signal is selected. VILMAX = 0.4V VIHMIN = 1.0V 10k 100µA 40k 30k 200 100µA 40k 16 YM YS/YMSW YM control input. When YM is high, the YSSW output signal is attenuated by 9.6dB. VILMAX = 0.4V VIHMIN = 1.0V 100µA 40k Pin No. Symbol Equivalent circuit Description

– 6 – CXA2000Q Power supply for RGB block. R2IN G2IN B2IN Analog/digital (dual-purpose) RGB signal inputs. The input signals are input via capacitors. When using analog input, input a 0.7Vp-p signal (no sync, 100 IRE); when using digital input, input a signal of at least 1.5Vp-p (Vth = 1.2V). The display level is 67 IRE. When using digital input, digital input is selected regardless of the YS setting. In addition, the VM output is turned off. These pins are clamped to 5.7V at the burst timing of the signal input to the sync input pin (Pin 47). 30k 200 100µA RSH GSH BSH Sample-and-hold for R, G and B AKB. Connect to GND via a capacitor. When not using AKB (manual CUTOFF mode), R, G and B cut-off voltage can be controlled by applying a control voltage to each pin. The control voltage is 4.5 ± 1V. 200 ROUT GOUT BOUT R, G and B signal outputs. 2.5Vp-p is output during 100% white input. 1.1mA 200 12k

27 IKIN

Input the signal converted from the CRT beam current (cathode current Ik) to a voltage via a capacitor. The V blanking part is clamped to 2.7V at the V retrace timing. The input for this pin is the reference pulse return, and the loop operates so that the Rch is 1Vp-p and the G and Bch are 0.81Vp-p. The G and Bch can be varied by ±0.5V by the bus CUTOFF control. When not using AKB, this pin should be open. 50µA

20 SV CC 2

No. Symbol Equivalent circuit Description

– 7 – CXA2000Q Connect a capacitor to form the LPF of the ABL control signal.

28 ABLIN/VCOMP

ABL control signal input and VSAW high voltage fluctuation compensation signal input. High voltage compensation has linear control characteristics for the pin voltage range of about 8V to 1V. The control characteristics can be varied through EHT-V control of the bus. ABL begins to have effect below a threshold voltage of about 1.2V. ABL functions as PIC/BRT-ABL (average value type).

29 ABLFIL

30 VTIM

V timing pulse output. Outputs the timing pulse from V sync identification to the end of V blanking. Pulses are positive polarity from 1 to 6V. During zoom mode, the V blanking pulse which has been expanded before and after the V sync is superimposed and output as the 1 to 3V pulse. 1.5V 147 1.2k 100k 10k

31 VD–OUT/VPROT

V sawtooth wave output and V protect signal input. When a large current (3mA) is drawn from this pin, the RGB outputs are all blanked and "1" is output to the status register VNG. 400µA 700 24k 30k

32 VD+OUT/VPROT

Serves as both a V sawtooth wave output with the reverse polarity of VD–OUT, and a Vprotect signal input. The Vprotect function can even be applied to this pin. 400µA 700 30k 24k Pin No. Symbol Equivalent circuit Description

– 8 – CXA2000Q H deflection pulse input for H AFC. Input an about 5Vp-p pulse via a capacitor. Set the pulse width to 10 to 12µs. This pin is also used as the hold- down signal input for the HD output, and if this pin is 1V or less for a 7V cycle or longer, the hold-down function operates and the HD output is held to 9VDC. In addition, the RGB outputs are all blanked. Outputs "1" to the status register XRAY. 33 E-WOUT V parabola wave output.

34 VAGCSH

Sample-and-hold for AGC which maintains the V sawtooth wave at a constant amplitude. Connect to GND via a capacitor. 800µA 15k 78k 1.4k 1.2k

35 SAWOSC

Connect a capacitor to generate the V sawtooth wave. For the capacitor, use an MPS (metalized polyester capacitor), etc., with a small tan d. 100 300 36 DV CC 1 Power supply for the V deflection block.

37 HD OUT

H drive signal output. This signal is output with the open collector. 147 20k AFCPIN/HOFF 10k 68k 10k147 4.2V Pin No. Symbol Equivalent circuit Description

– 9 – CXA2000Q CR connection for the AFC lag-lead filter. IREF

39 L2FIL

Filter for H AFC. Connect to GND via a capacitor. The H phase can also be controlled from this pin by leading current in and out of this capacitor. As the pin voltage rises, the picture shifts to the left; as the pin voltage drops, the picture shifts to the right.

40 AFCFIL

1.2k

41 CERA Connect the 32 · FH VCO ceramic

oscillator.41 400µA 10k DGND DV CC 2 Power supply for the H deflection block. GND for the deflection block. Internal reference current setting. Connect to GND via a resistor with an error of less than 1% (such as a metal film resistor). 147 20k 45 VSFIL Filter for V sync separation. Connect to GND via a capacitor. Pin No. Symbol Equivalent circuit Description

– 10 – CXA2000Q Sync signal output for VSIN and HSIN. The output can be selected from the internal sync signals (Pin 53 or Pin 55) or the external sync signal (Pin 56) by the I 2C bus. Output signal level: 2Vp-p (0.6Vp-p sync only) Input/output gain: 6dB

46 VSIN

Sync signal input for V sync separation. Input a 2Vp-p Y signal (or a 0.6Vp-p sync signal).

47 HSIN

Sync signal input for H sync separation. Input a 2Vp-p Y signal (or a 0.6Vp-p sync signal).

48 SYNCOUT

4.1V 20µA 15k 147 3.2V 10µA 14k 240µA 1.2k 40k 147 49 VM Outputs the differential waveform of the VM (Velocity Modulation) Y signal. (6.6VDC, 1.1Vp-p) The signal advanced for 200ns from YOUT is output. The delay time versus YIN is determined by the DL setting of the I 2C bus. This output can be turned off through the I2C bus. This output can also be turned off by YS1, YM, and YS2. 400µA 500 30k147 1.2k

50 SCL

I2C bus protocol SCL (Serial Clock) input. VILMAX = 1.5V VIHMIN = 3.5V Pin No. Symbol Equivalent circuit Description

– 11 – CXA2000Q Capacitor connection for black peak hold of the dynamic picture (black expansion).

51 SDA

I2C bus protocol SDA (Serial Data) I/O. VILMAX = 1.5V VIHMIN = 3.5V VOLMAX = 0.4V

52 BLHOLD

53 CVIN

Composite video signal input. Input the 1Vp-p (100% white including sync) CV signal via a capacitor. The sync level of the input signal is clamped to 3.8V. In addition, this pin detects input video signal HSYNC, and outputs the status via the status register CVSYNC. 1.2k 9µA 20k 20k 4.6V 1µA 4.6V

54 DCTRAN Connect a capacitor that determines the

DC transmission ratio to GND. 1.2k4k

55 YIN

Y signal input. Input a 1Vp-p (100% white including sync) Y signal via a capacitor. The sync level of the input signal is clamped to 3.8V. 1µA 4.6V Pin No. Symbol Equivalent circuit Description

– 12 – CXA2000Q Chroma signal input. Input a C signal with a burst level of 300mVp-p via a capacitor. Input signal is biased to 4.5V internally.

56 EXT SYNC IN

External sync signal input. Input a 0.3Vp-p sync signal (or a 1Vp-p CV signal or Y signal) via a capacitor. The sync level of the input signal is clamped to 3.8V.

57 CIN

1µA 4.6V 30k 5.2V 50k

58 TEST

Test pin. Outputs a 0 to 3V V-SYNC SEP with positive polarity. If not used, leave this pin open. 15k 59 SV CC 1 Power supply for Y/C block.

60 APCFIL CR connection for the chroma APC lag-

lead filter. 1.2k 4.6V 1.2k 61 X443 Connect a 4.433619MHz crystal oscillator. 200µA 500 Pin No. Symbol Equivalent circuit Description

– 13 – CXA2000Q Not connected. Normally connected to GND to prevent interference with other pins. 62 X358 Connect a 3.579545MHz crystal oscillator. 200µA 500 64 FSCOUT Subcarrier output. Output level: 5.2VDC, 0.4Vp-p 280µA 1.2k 147 63 NC Pin No. Symbol Equivalent circuit Description

– 14 – CXA2000Q

Electrical Characteristics

Setting conditions • Ta = 25°C, SVCC 1, 2 = DVCC 1, 2 = 9V, SGND1, 2 = DGND = 0V

• Measures the following after setting the I2C bus register as shown in "I2C Bus Register Initial Settings". SICC DICC fHFR ∆fHR HDw VBLKh VBGPh VSp-p VSdc 15.90 400 26.5 12.6 3.3 1.1 3.1 15.55 –400 24.5 11.6 2.5 0.9 2.9 Measure the pin inflow current. Measure the pin inflow current. HDRIVE output frequency Confirm that I2C status register HLOCK is 1 (the pull-in range when f H is shifted from 15.734kHz). Measure the pulse width for the section where the HDRIVE output is high. Measure the VDRIVE output Vp-p. VCC = 9.0V, Bus data = center VCC = 9.0V, Bus data = center AFC MODE = 0h SYNCIN: composite sync SYNCIN: composite sync SCP Measure the pulse width for the section where the BLK output is high. SCP Measure the pulse width for the section where the BGP output is high. SYNCIN: composite sync Signal block current consumption Sync block current consumption Horizontal free-running frequency Horizontal sync pull-in range HD output pulse width SCP BLK output pulse width SCP BGP output pulse width VDRIVE output amplitude VDRIVE output center potential 20, 59 36, 44 31, 32 31, 32 mA mA kHz Hz µs µs µs V V No. Item Symbol Measurement conditions Measurement pins Measurement contents Min. Typ. Max. Unit Sync deflection block items VBGPh VBLKh VSp-p 10.79ms VDRIVE+ VSdc 46: VSIN in 15.734 25.5 12.1 2.9 1.0 3.0

– 15 – CXA2000Q Measure the EWDRIVE output Vp-p. Output amplitude when a video signal with an amplitude of 0.7Vp-p/100 IRE is input. Input fsc to CVIN. Ratio of the fsc component of the Yout amplitude when CTRAP = 1 against the Yout amplitude when CTRAP = 0. SYNCIN: composite sync TRAPOFF = 0/1 TRAP-F0 = 7h EWDRIVE output amplitude EWDRIVE output center potential R, G and B output amplitude R, G and B output linearity C-TRAP attenuation (3.58MHz) VEWp-p VEWdc VRout1 Lin C-Trap3.58 22, 24, 26 22, 24, 26 0.42 3.8 2.25 0.52 3.95 2.5 100 –30 0.62 4.1 2.85 104 V V V dB No. Item Symbol Measurement conditions Measurement pins Measurement contents Min. Typ. Max. Unit Signal block items VEWp-p 10.79ms VEW dc 46: VSIN in Lin = V2 × 2 V1 × 100 f = 3.58MHz CVIN: 0.7Vp-p /100 IRE CVIN: 100 IRE

50 IRE

CVIN: fsc, 50 IRE

– 16 – CXA2000Q Input fsc to CVIN. Ratio of the fsc component of the Yout amplitude when CTRAP = 1 against the Yout amplitude when CTRAP = 0. TRAPOFF = 0/1 TRAP-F0 = 7h CVIN: 3MHz, 50 IRE VMOFF = 0 4.43MHz PAL input burst fsc 300mVp-p 640mVp-p fsc + 90° SUB-COLOR = 7h PAL input: COLOR = 1Fh PAL input: COLOR = 1Fh C-TRAP attenuation (4.43MHz) VM output Color difference –(R-Y) output Color difference –(B-Y) output Color gain –(R-Y) Color gain –(B-Y) C-Trap4.43 Vvm Vr-y Vb-y Vcolr-y Vcolb-y 0.75 440 570 1.4 1.1 –30 0.95 510 640 1.6 1.3 1.15 570 710 1.8 1.5 dB V mV mV V V No. Item Symbol Measurement conditions Measurement pins Measurement contents Min. Typ. Max. Unit BOUT Vcolb-y ROUT Vcolr-y –(B-Y) OUT Vb-y –(R-Y) OUT Vr-y f = 3MHz f = 4.43MHz CVIN: fsc, 50 IRE 450mVp-p fsc + 0°, fsc + 180° CIN –(R-Y) IN: 525mVp-p –(B-Y) IN: 665mVp-p

– 17 – CXA2000Q Confirm that the burst frequency is pulled in at 3.58MHz ±400Hz. ROUT, BOUT ∆GdcolR = · 100 ∆GdcolB = · 100 Output amplitude ratio when the R, G and BOUT YM = 1 and 0 VLR1out = Vout VLG1out = Vout VLB1out = Vout HUE = 1Fh, SUB – HUE = 7h CVIN: Burst only D-COL = 0/1 YS1: 1V RGB1IN: 0.7Vp-p YS1: 1V RGB1IN: 0.7Vp-p YS1: 1V RGB1IN: 0.7Vp-p Hue center offset Killer point APC pull-in range Dynamic color operation R output Dynamic color operation B output YM gain R output amplitude during linear R1 input G output amplitude during linear G1 input B output amplitude during linear B1 input foffset KP ∆fAPC ∆GdcolR ∆GdcolB ∆GYM VLR1out VLG1out VLB1out 22, 24, 26 –400 102 –10.6 1.85 1.85 1.85 –35 104 –9.6 2.05 2.05 2.05 400 106 –8.6 2.25 2.25 2.25 deg dB Hz dB V V V No. Item Symbol Measurement conditions Measurement pins Measurement contents Min. Typ. Max. Unit Vp-p (DCOL = 1) Vp-p (DCOL = 0) Vp-p (DCOL = 1) Vp-p (DCOL = 0) Vp-pCVIN: 100 IRE RGB1 IN R, G, B out

– 18 – CXA2000Q Unit VLR2out = Vout VLG2out = Vout VLB2out = Vout VDRout = Vout VDGout = Vout VDBout = Vout YS2: 1V RGB2IN: 0.7Vp-p YS2: 1V RGB2IN: 0.7Vp-p YS2: 1V RGB2IN: 0.7Vp-p RGB2IN: 1.5Vp-p RGB2IN: 1.5Vp-p RGB2IN: 1.5Vp-p SYNCIN: composite sync GCUTOFF = 0h BCUTOFF = 0h R output amplitude during linear R2 input G output amplitude during linear G2 input B output amplitude during linear B2 input R output amplitude during digital R2 input G output amplitude during digital G2 input B output amplitude during digital B2 input IK level R IK level G IK level B VLR2out VLG2out VLB2out VDRout VDGout VDBout VIKR VIKG VIKB 1.85 1.85 1.85 0.85 0.22 0.22 2.05 2.05 2.05 1.00 0.35 0.35 2.25 2.25 2.25 1.15 0.5 0.5 V V V IRE IRE IRE V V V No. Item Symbol Measurement conditions Measurement pins Measurement contents Min. Typ. Max. RGB2 IN RGB2 IN VIKG VIKR VIKB R, G, B out R, G, B out

– 19 – CXA2000Q Electrical Characteristics Measurement Circuit Signal sources are all GND unless otherwise specified in the Measurement conditions column of Electrical Characteristics. YOUT B2IN –(R-Y) IN G1IN SGND2 R2IN YS1 YS2 SECAMREF G2IN YRET R1IN –(B-Y) IN YM SCPOUT B1IN –(R-Y) OUT SGND1 –(B-Y) OUT 120µ SECAMREF –(R-Y) OUT –(B-Y) OUT Y OUT 0.1µ –(R-Y) IN 0.1µ 0.1µ –(B-Y) IN SCP OUT 220 YS1 0.01µ 220 YS2 220 YM 0.01µ 0.01µ RGB1IN RGB2IN 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 191 3.3k 4700p 500k SDA 220 SCL 220 VM 100p 560 4700p 100 +9V 330k +9V 0.47µ 0.01µ 47µ 10k 270 8.2k 0.01µ E/W 1000.1µ0.1µ (MPS) +9V 0.01µ 47µ +9V 2.7k 0.01µ HP GEN. 10k HOFF 40 39 38 37 364142434445464748495051 35 34 33 HSIN E-WOUT VSFIL L2FIL IREF SAWOSC DGND HDOUT SDA VAGCSH VSIN AFCFIL DVCC2 DVCC1 CERA AFCPIN/HOFF VM SCL SYNCOUT10µ 10µCV IN 0.47µ 10µY IN 10µEXT SYNC IN 10µC IN TEST EXT SYNC IN TEST FSC OUT APCFIL X358 BLHOLD CIN NC SV CC 1 X443 DCTRAN CVIN YIN FSC OUT 1.5k3.58MHz15p 4704.43MHz15p 470p 0.01µ 47µ0.47µ 15k +9V +9V 0.01µ 47µ0.1µ 0.1µ 100 100 0.1µ 100 20k 51k 20k ABLIN/VCOMP BOUT SV CC 2 GOUT ROUT VD+OUT/VPROT IKIN RSH BSH GSH VTIM VD–OUT/VPROT ABLFIL 0.001µ +9V IK IN 100 10µ 100 100 10k 820 VPROT R OUT G OUT B OUT 0.01µ 0.01µ 0.01µ VTIM VDRV– VDRV+

– 20 – CXA2000Q 1T1 VSS 1T2 1CD VDD 2T1 2T2 2CD TC4538BP from HDOUT 10k 2 3 4 5 6 7 81 2000p 10k 2000p 910111213141516 47µ to AFCPIN HDOUT delay 7µs AFCPIN width12µs HP GEN.

– 21 – CXA2000Q Application Circuit YOUT B2IN –(R-Y) IN G1IN SGND2 R2IN YS1 YS2 SECAMREF G2IN YRET R1IN –(B-Y) IN YM SCPOUT B1IN –(R-Y) OUT SGND1 –(B-Y) OUT SECAM reference input/output for SECAM IC 0.1µ 3.3k 4700p 500k I2C BUS input/output 220 220 VM output 100p 470 0.0047µ 100 2.2k +9V +9V 0.47µ 47µ 0.01µ 10k 470 5.6k 2.2µ 0.01µ 1000.1µ0.1µ +9V 0.01µ 47µ0.1µ 10k HSIN E-WOUT VSFIL L2FIL IREF SAWOSC DGND HDOUT SDA VAGCSH VSIN AFCFIL DVCC2 DVCC1 CERA AFCPIN/HOFF VM SCL SYNCOUT4.7µ CV signal input 0.47µ 2.2µ 2.2µ 0.47µ EXT SYNC IN TEST APCFIL X358 BLHOLD CIN NC SV CC 1 X443 DCTRAN CVIN YIN FSC OUT 1.5k 3.579545MHz 15p 510 4.433619MHz 15p 470p 0.01µ 47µ 0.47µ 15k +9V +9V 0.01µ 47µ0.1µ 0.1µ 100 100 0.1µ 100 ABLIN/VCOMP BOUT SV CC 2 GOUT ROUT VD+OUT/VPROT IKIN RSH BSH GSH VTIM VD–OUT/VPROT ABLFIL 0.001µ 220 100 10µ 100 100 820 Color difference outputs for 1H delay line Color difference outputs from 1H delay line 0.1µ 0.1µ Sand castle pulse output YS1 input 220 Analog RGB inputs YS2/YM inputs 220 220 Analog/digital RGB inputs RGB outputs 1µ 10µ Ik input ABL/Vertical high voltage fluctuation compensation signal input 10k V protect signal input V timing pulse output V sawtooth wave outputs HD outputHP outputHold-down input 330k 220 Y signal input External sync signal input C signal input 2.2µ 40 39 38 37 364142434445464748495051 35 34 33 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 191 ∗1: Metal film resistor recommended ∗2: MPS capacitor recommended V parabola wave output 0.01µ 0.01µ 0.01µ 0.01µ 0.01µ 0.01µ 2.7k 1000.1µ Application circuits shown are typical examples illustrating the operation of the devices. Sony cannot assume responsibility for any problems arising out of the use of these circuits or for any infringement of third party patent and other right due to same.

– 22 – CXA2000Q Electrical Characteristics Measurement Conditions "I2C Bus Register Initial Settings" Register name No. of bits Initial setting Description PICTURE TRAPOFF VMOFF HUE DCTRAN D-PIC COLOR TOT BRIGHT D-COL SHARPNESS PRE-OVER COLOR SW SUB-CONT TRAP F0 SUB-COLOR SUB-HUE SUB-BRIGHT GAMMA G-DRIVE AGING B-DRIVE INTERLACE G-CUTOFF B-CUTOFF RON GON BON PICON VOFF FHHI CD-MODE AKBOFF V-SIZE 3Fh 1Fh 1Fh 1Fh 1Fh 2Ah 2Ah 1Fh Maximum value TRAP off VM off Center value DCTRAN off DPIC off Center value TOT off Center value DCOL off Center value Maximum value Automatic switching Center value Center value Center value Center value Center value Minimum value Center value AGING off Center value Interlace Minimum value Minimum value R output on G output on B output on Picture mute off VD output on FH normal Automatic switching AKB on Center value V FREQ V-POSITION AFC-MODE S-CORR V-LIN H-SIZE REF-POSI PIN-COMP VBLKW H-POSITOPN PIN-PHASE AFC-BOW AFC-ANGLE SCP BGR SCP BGF XTAL EXT SYNC CV/YC V-ASPECT ZOOM SW HBLKSW V-SCROLL JMPSW HSIZESW UP-VLIN LO-VLIN LEFT-BLK RIGHT-BLK EHT H EHT V CORNER-PIN YS1OFF DL 1Fh 1Fh 1Fh 1Fh Automatic switching Center value Low gain Minimum value Center value Center value Maximum value Center value Minimum value Center value Center value Center value Center value Center value Center value Automatic switching Internal sync CV input Minimum value ZOOM SW off HBLKSW off Center value JMPSW off HSIZESW off Minimum value Minimum value Center value Center value EHT H off EHT V off Center value YS1 normal Center value Register name No. of bits Initial setting Description

– 23 – CXA2000Q TRAP F0 SUB-HUE B-CUTOFF V-LIN PIN-PHASE AFC-ANGLE LO-VLIN RIGHT-BLK CORNER-PIN PICTURE HUE COLOR BRIGHT SUB-BRIGHT G-DRIVE B-DRIVE V-SIZE V-POSITION H-SIZE PIN-COMP V-ASPECT V-SCROLL SHARPNESS SUB-CONT SUB-COLOR G-CUTOFF S-CORR H-POSITION AFC-BOW UP-VLIN LEFT-BLK Definition of I2C Bus Registers Slave Addresses 88h: Slave Receiver 89h: Slave Transmitter Register Table "*": Undefined Control Register Bit0Bit1Bit2Bit3Bit4Bit5Bit6Bit7 Sub Address

• ·· 0 0 0 0 0 00 h
• ·· 0 0 0 0 1 01 h
• ·· 0 0 0 1 0 02 h
• ·· 0 0 0 1 1 03 h
• ·· 0 0 1 0 0 04 h
• ·· 0 0 1 0 1 05 h
• ·· 0 0 1 1 0 06 h
• ·· 0 0 1 1 1 07 h
• ·· 0 1 0 0 0 08 h
• ·· 0 1 0 0 1 09 h
• ·· 0 1 0 1 0 0A h
• ·· 0 1 0 1 1 0B h
• ·· 0 1 1 0 0 0C h
• ·· 0 1 1 0 1 0D h
• ·· 0 1 1 1 0 0E h
• ·· 0 1 1 1 1 0F h
• ·· 1 0 0 0 0 10 h
• ·· 1 0 0 0 1 11 h
• ·· 1 0 0 1 0 12 h
• ·· 1 0 0 1 1 13 h
• ·· 1 0 1 0 0 14 h
• ·· 1 0 1 0 1 15 h
• ·· 1 0 1 1 0 16 h
• ·· 1 0 1 1 1 17 h
• ·· 1 1 0 0 0 18 h
• ·· 1 1 0 0 1 19 h TRAPOFF DC-TRAN TOT D-COL VMOFF D-PIC PRE-OVER COLOR SW GAMMA AGING 0 AKBOFFCD-MODEFHHIVOFFPICONBONGONRON V-FREQ AFC-MODE REF-POSI VBLKW EXT SYNC ZOOM SW JMP SW CV/YC HBLKSW HSIZESW Status Register Bit0 CV SYNC Bit1Bit2Bit3Bit4 XRAY Bit5 VNG Bit6 IKR Bit7 H LOCK INTERLACE SCP BGR SCP BGF XTAL EHT H EHT V ** * YS1 OFF DL* COLOR SYS

– 24 – CXA2000Q Description of Registers Register name (No. of bits) 1. Video switch register CV/YC (1) : CV input/YC input selector 0 = CV input selected 1 = YC input selected EXT SYNC (1) : EXT SYNC selector switch 0 = Internal sync (CV or Y) selected 1 = EXT SYNC selected 2. Y signal block register SUB-CONT (4) : Contrast gain control (Y gain control) 0h = –3.5dB 7h = 0dB Fh = +2.5dB TRAP-F0 (4) : Chroma trap f0 fine adjustment (Y block chroma trap current control) 0h = High 7h = Center Fh = Low SHARPNESS (4) : Sharpness gain control (Sharpness F0 3MHz) 0h = –6dB 7h = +2.5dB Fh = +6.5dB PRE-OVER (2) : Sharpness preshoot/overshoot ratio control 0h = 1:1 (PRE: OVER) 3h = 2:1 VM OFF (1) : Y signal output ON/OFF for VM 0 = ON 1 = OFF TRAP OFF (1) : Y block chroma trap ON/OFF 0 = Trap ON 1 = Trap OFF DL (3) : Y signal delay time control (80ns/step) 0h = Max. 7h = Min.

– 25 – CXA2000Q DC-TRAN (1) : Y DC transmission ratio selector switch 0 = 100% 1 = 81% D-PIC (1) : Y black expansion ON/OFF switch 0 = OFF 1 = ON Point of inflection: 30 IRE 3. C signal block register TOT (1) : Chroma TOT filter band selector switch 0 = TOT — TRAP OFF 1 = TOT — TRAP ON (TRAP fo 2MHz) COLOR (6) : Color gain control (Chroma gain control) 0h = Color OFF (–40dB or less) 1Fh = 0dB B output: 1.02Vp-p (I/O gain: +11dB, 0.285Vp-p input) 3Fh = +6dB SUB-COLOR (4) : Color gain control (ACC reference level control) 0h = –5dB 7h = 0dB Fh = +3dB HUE (6) : Hue control (Phase control for chroma demodulation axis when SUB-HUE is 7h) Control not possible for a PAL system. 0h = +35° Flesh color appears red. 1Fh = 0° 3Fh = –35° Flesh color appears green. SUB-HUE (4) : Hue control (Phase control for chroma demodulation axis when HUE is 1Fh) B-Y axis adjustable to 0°. Control not possible for a PAL system. 0h = +10° 7h = 0° Fh = –10° XTAL (2) : XTAL selection setting switch 0h = Automatic identification 1h = Force to XTAL1 (3.58MHz) 2h = Force to XTAL2 (4.43MHz) COLOR SW (2) : Color system setting 0h = Automatic identification 1h = Force to PAL 2h = Force to NTSC 3h = Force to SECAM

– 26 – CXA2000Q 4. RGB signal block register PICTURE (6) : Picture gain control (RGB gain control) 0h = –14dB 3Fh = 0dB RGB output: 2.5Vp-p (I/O gain: +8dB, 1Vp-p input) BRIGHT (6) : Bright control (RGB DC bias control) 0h = –440mV 1Fh = 0mV (–300mV for REF-P level) 3Fh = +450mV SUB-BRIGHT (6) : Bright control (RGB DC bias control) 0h = –440mV 1Fh = 0mV (–300mV for REF-P level) 3Fh = +450mV G-DRIVE (6) : Gch drive gain adjustment (Gch gain control) 0h = G/R –4.5dB 2Ah = G/R 0dB (G/R 0dB) 3Fh = G/R +1.5dB B-DRIVE (6) : Bch drive gain adjustment (Bch gain control) 0h = B/R –4.5dB 2Ah = B/R 0dB (B/R 0dB) 3Fh = B/R +1.5dB G-CUTOFF (4) : Gch cut-off adjustment (Gch reference pulse value control of IKIN pin input) 0h = +34% 7h = +81% (G/R) Fh = +135% B-CUTOFF (4): Bch cut-off adjustment (Bch reference pulse value control of IKIN pin input) 0h = +34% 7h = +81% (B/R) Fh = +135% D-COL (1) : Dynamic color ON/OFF switch 0 = Dynamic color OFF 1 = Dynamic color ON (R, Bch level control) GAMMA (2) : Gamma control (RGB gamma correction amount control) 0h = Gamma OFF 3h = Gamma peak 17 IRE (at input 40 IRE), +400mV (at 2.5Vp-p OUT)

– 27 – CXA2000Q REF-POSITION (2) : Reference pulse timing setting 0h = From rising edge of V TIM: Rch 22H, Gch 23H, Bch 24H 1h = From rising edge of V TIM: Rch 20H, Gch 21H, Bch 22H 2h = From rising edge of V TIM: Rch 18H, Gch 19H, Bch 20H 3h = From rising edge of V TIM: Rch 16H, Gch 17H, Bch 18H PIC-ON (1) : ON/OFF switch for RGB output with a reference pulse (Set to OFF mode at power-on.) 0 = RGB output OFF (All blanked status) 1 = RGB output ON R ON (1) : ON/OFF switch for Rch video output without a reference pulse (Operates when PIC ON = 1, set to OFF mode at power-on.) 0 = Rch video output OFF (Blanked status, reference pulse only output) 1 = Rch video output ON G ON (1) : ON/OFF switch for Gch video output without a reference pulse (Operates when PIC ON = 1, set to OFF mode at power-on.) 0 = Gch video output OFF (Blanked status, reference pulse only output) 1 = Gch video output ON B ON (1) : ON/OFF switch for Bch video output without a reference pulse (Operates when PIC ON = 1, set to OFF mode at power-on.) 0 = Bch video output OFF (Blanked status, reference pulse only output) 1 = Bch video output ON AKB OFF (1) : AKB ON/OFF switch (Set to ON mode at power-on.) 0 = AKB ON 1 = AKB OFF (IK CLAMP, IK S/H and reference pulse fixed to OFF) R, G and B cut-off adjustment at AKB OFF performed by voltage applied to RSH, GSH and BSH pins, respectively. YS1 OFF (1) : YS1 forced OFF mode/YS1 normal mode 0 = YS1 normal mode 1 = YS1 forced OFF mode

– 28 – CXA2000Q 5. Deflection block register AFC-MODE (2) : AFC loop gain control (PLL between H SYNC and H VCO) 0h = H free run mode 1h = Small gain 2h = Medium gain 3h = Large gain FH-HI (1) : H oscillator frequency fixation ON/OFF switch (Set to ON mode at power-on.) 0 = H oscillator frequency fixation OFF AFC normal mode 1 = H oscillator frequency fixation ON Oscillator frequency fixed to maximum value (approx. 16.2kHz). V FREQ (1) : V frequency mode setting 0, 1h = Automatic identification 2h = Forced mode (50Hz) 3h = Forced mode (60Hz) V OFF (1) : V sawtooth wave oscillation stop ON/OFF switch (Set to OFF mode at power-on.) 0 = Oscillation stop OFF (V DRIVE– and V DRIVE+: normal output) 1 = Oscillation stop ON (V DRIVE– and V DRIVE+: DC output and DC value vary according to V POSITION.) CD-MODE (1) : V countdown system mode selector (Set to automatic selection mode during power-on.) 0 = Non-standard signal mode, standard signal mode and no signal mode automatically selected 1 = Fixed to non-standard signal mode (V oscillator frequency is 55Hz during no signal mode "free run".) VBLKW (2) : VBLK width control (Blanked pulses after reference pulse. Operates when JMPSW = 1; blanked pulses after reference pulse fixed to 1H when JMPSW = 0.) 0h = 12H from Bch reference pulse 1h = 11H from Bch reference pulse 2h = 10H from Bch reference pulse 3h = 9H from Bch reference pulse H-POSITION (4) : Horizontal position adjustment (HAFC phase control) 0h = 1µs delay Picture position shifts to right. (Picture delayed with respect to HD.) 7h = 0µs Fh = 1µs advance Picture position shifts to left. (Picture advanced with respect to HD.) V-POSITION (6) : Vertical position adjustment (V SAW output DC bias control) 0h = –0.09V Picture position drops, V DRIVE+ output DC Down. 1Fh = 0V Center potential: DC 3V 3Fh = +0.09V Picture position rises, V DRIVE+ output DC Up.

– 29 – CXA2000Q V-SIZE (6) : Vertical amplitude adjustment (V SAW output gain control) 0h = –14% Vertical picture size decreases. 1Fh = 0%Amplitude: 1.23Vp-p, center potential: DC 3V when V-ASPECT is 2FH. 3Fh = +14% Vertical picture size increases. V-LIN (4) : Vertical linearity adjustment (Gain control for V SAW secondary component) 0h = 115% (Bottom/top of picture) Top of picture compressed; bottom of picture expanded. 7h = 100% (Bottom/top of picture) Fh = 85% (Bottom/top of picture) Top of picture expanded; bottom of picture compressed. S-CORR (4) : Vertical S correction amount adjustment (V SAW secondary component gain control) 0h = Secondary component amplitude by adding sawtooth and other signals = 0 Fh = Secondary component amplitude by adding sawtooth and other signals = Maximum AFC-BOW (4) : Vertical line bow compensation amount adjustment (Phase control according to HAFC parabola wave) 0h = Top and bottom of picture delayed 500ns with respect to picture center. 7h = 0 ns Fh = Top and bottom of picture advanced 500ns with respect to picture center. AFC-ANGLE (4) : Vertical line slope compensation amount adjustment (Phase control according to HAFC V SAW) 0h = Top of picture delayed 500ns, bottom of picture advanced 500ns with respect to picture center. 7h = 0 ns Fh = Top of picture advanced 500ns, bottom of picture delayed 500ns with respect to picture center. PIN-COMP (6) : Horizontal pin distortion compensation amount adjustment (V parabola wave gain control) 0h = 0.10Vp-p Horizontal size for top/bottom of picture increases. (Compensation amount minimum) 1Fh = 0.58Vp-p Amplitude, center potential: DC 4V when V-ASPECT is 2Fh 3Fh = 1.06Vp-p Horizontal size for top/bottom of picture decreases. (Compensation amount maximum) H-SIZE (6) : Horizontal amplitude adjustment (V parabola wave DC bias control) 0h = –0.5V Horizontal picture size decreases, EW-DRIVE output DC Down. 1Fh = 0V Amplitude: 0.58Vp-p, center potential: DC 4 V when V-ASPECT is 2Fh 3Fh = +0.5V Horizontal picture size increases, EW-DRIVE output DC Up. EHT-H (2) : Horizontal high-voltage fluctuation compensation amount setting (DC adjustment for parabolic output) 0h = 0V (Compensation amount when 1V is applied to ABL IN versus 8V applied to ABL IN) 3h = –0.1V (Compensation amount when 1V is applied to ABL IN versus 8V applied to ABL IN) EHT-V (2) : Vertical high-voltage fluctuation compensation amount setting (V SAW output gain control) 0h = 0% (Compensation amount when 1V is applied to ABL IN versus 8V applied to ABL IN) 3h = –7% (Compensation amount when 1V is applied to ABL IN versus 8V applied to ABL IN) INTERLACE (1) : Interlace mode and non-interlace display selector switch 0,1h = Interlace mode 2h = Interlace mode; 1/2H shift applied to EVEN lines 3h = Interlace mode; 1/2H shift applied to ODD lines

– 30 – CXA2000Q PIN-PHASE (4) : Horizontal trapezoidal distortion compensation amount adjustment (V parabola wave center timing control) 0h = 1.5ms advance Horizontal size for top of picture increases; horizontal size for bottom of picture decreases. 7h = 0ms 8.9ms from 4VDC VTIM Fh = 1.5ms delay Horizontal size for top of picture decreases; horizontal size for bottom of picture increases. CORNER-PIN (4) : Horizontal pin distortion compensation amount adjustment for top/bottom of picture (V parabola wave top/bottom gain control) 0h = –0.2V Horizontal size for top/bottom of picture decreases. (compensation amount maximum) 7h = 0V (0.7Vp-p 4:3 mode) Fh = +0.2V Horizontal size for top/bottom of picture increases. (compensation amount minimum) V-ASPECT (6) : Aspect ratio control. (Gain control for sawtooth wave) 0h = 75% 16:9 CRT full 2Fh = 100% 4:3 CRT full, amplitude: 1.23Vp-p 3Fh = 112% ZOOM SW (1) : Zoom mode ON/OFF switch for 16:9 CRT (25% of video cut) 0 = Zoom OFF Sawtooth wave amplitude: 1.23Vp-p 1 = Zoom ON Sawtooth wave amplitude: 70% HBLKSW (1) : HBLK width control ON/OFF switch during 4:3 software full display mode on a 16:9 CRT 0 = Control OFF HBLK pulse generated from HPIN. 1 = Control ON HBLK pulse generated as pulse generated from HPIN or as pulse generated from HVCO and width adjusted. Width adjustment is performed by the LEFT-BLK and RIGHT-BLK registers. V-SCROLL (6) : Vertical picture scroll control during zoom mode on a 16:9 CRT (DC component added to sawtooth wave AGC output to control ZOOMSW cut timing.) 0h = –0.2V Scrolled toward top of screen by 32H and top of picture zoomed. 1Fh = 0V 3Fh = +0.2V Scrolled toward bottom of screen by 32H and bottom of picture zoomed. JUMPSW (1) : Reference pulse jump mode ON/OFF switch (In addition to V-ASPECT control, sawtooth wave gain control performed for 100% of VBLK interval and 67% of picture interval) 0 = Jump mode OFF 1 = Jump mode ON On a 4:3 CRT, jump mode expands the sawtooth wave amplitude to 112% with V- ASPECT; on a 16:9 CRT, jump mode compresses the sawtooth wave amplitude to 75% with V-ASPECT. The V blanking width is expanded at both the top and bottom of the picture. Blanking for the bottom of the picture starts 251H after VTIM, and blanking for the top of the picture can be varied as the blanking width after the reference pulse from the VBLKW register. HSIZESW (1) : Lowers the E-W OUT DC level (during H-SIZE compression) 0 = Normal 1 = –1.35V

– 31 – CXA2000Q UP-VLIN (4) : Vertical linearity adjustment for top of picture (Secondary component gain control for sawtooth wave added to sawtooth wave AGC output) 0h = 100% (Bottom/top of picture) Fh = 115% (Bottom/top of picture) Top of picture compressed. LO-VLIN (4) : Vertical linearity adjustment for bottom of picture (Tertiary component gain control for sawtooth wave added to sawtooth wave AGC output) 0h = 100% (Bottom/top of picture) Fh = 85% (Bottom/top of picture) Bottom of picture compressed. LEFT-BLK (4) : HBLK width control for the left side of picture when HBLKSW = 1 (Phase control for timing pulse generated from HVCO) 0h = +1.3µs HBLK width maximum 7h = 0µs Center HBLK: 13µs Fh = –1.3µs HBLK width minimum RIGHT-BLK (4) : HBLK width control for the right side of picture when HBLKSW = 1 (Phase control for timing pulse generated from HVCO) 0h = +1.3µs HBLK width maximum 7h = 0µs Center HBLK: 13µs Fh = –1.3µs HBLK width minimum SCP BGR (2) : Controls the phase of the rising edge of the burst pulse in sand castle pulse output (0.4µs/step) 0h = +0.4µs 1h = Center 3h = –0.8µs SCP BGF (2) : Controls the phase of the falling edge of the burst pulse in sand castle pulse output (0.4µs/step) 0h = +0.4µs 1h = Center 3h = –0.8µs 6. Other AGING (1) : White output aging mode ON/OFF switch (Takes priority over RGB ON and PIC ON control. Set to OFF mode at power-on.) 0 = Aging mode OFF 1 = Aging mode ON (When there is no input signal, a 60 IRE flat signal is output from the Y block)

– 32 – CXA2000Q 7. Status register HLOCK (1) : Lock status between H SYNC and H VCO 0 = HVCO free run status 1 = Locked to H SYNC IKR (1) : AKB operation status 0 = REF-P at Ik small and AKB loop unstable. 1 = REF-P at Ik sufficient and AKB loop stable. VNG (1) : Signal input status to V PROT pin 0 = No V PROT input 1 = V PROT input (In this case, the RGB output is blanked.) XRAY (1) : Signal input status to XRAY control pin (HOFF pin) 0 = No XRAY control input 1 = XRAY control input (In this case, the RGB output is blanked.) COLOR SYS (3) : Color system status 0h = — 1h = — 2h = NO STANDARD 3h = SECAM 4h = 3.58MHz NTSC 5h = 4.43MHz NTSC 6h = 3.58MHz PAL 7h = 4.43MHz PAL CV SYNC (1) : CV input SYNC SEP result When VIDEO is input to CVIN, "1" is returned when the SYNC level is 100mV or more (standard: 300mV) 0 = No SYNC 1 = SYNC

– 33 – CXA2000Q Description of Operation 1. Power-on sequence The CXA2000Q does not have an internal power-on sequence. Therefore, power-on sequence is all controlled by the set microcomputer (I 2C bus controller). 1) Power-on The IC is reset and the RGB outputs are all blanked. Hdrive starts to oscillate, but oscillation is at the maximum frequency (16kHz or more) and is not synchronized to the input signal. Output of vertical signal VTIM starts, but Vdrive is DC output. Bus registers which are set by power-on reset are as follows. AGING = 0: All white output aging mode OFF RON = 0: Rch video blanking ON GON = 0: Gch video blanking ON BON = 0: Bch video blanking ON PICON = 0: RGB all blanking ON VOFF = 1: VDRIVE output stopped mode VFREQ = 0: Automatic identification mode (identification starts at 50Hz) FHHI = 1: H oscillator maximum frequency mode HSIZESW = 0: Normal CD-MODE = 0: Automatic selection mode of the countdown mode AKBOFF = 0: AKB mode 2) Bus register data transfer The register setting sequence differs according to the set sequence. Register settings for the following sequence are shown as an example. Set sequence CXA2000Q register settings Power-on Reset status in 1) above. flfl Degauss Reset status in 1) above. The CRT is degaussed in the completely darkened condition. flfl VDRIVE oscillation The IC is set to the power-on initial settings. (See the following page.) A sawtooth wave is output to VDRIVE and the IC waits for the vertical deflection to stabilize. The HDRIVE oscillator frequency goes to the standard frequency. flfl AKB operation start PICON is set to 1 and a reference pulse is output from Rout, Gout and Bout. Then, the IC waits for the cathode to warm up and the beam current to start flowing. flfl AKB loop stable Status register IKR is monitored. IKR = 0: No cathode current IKR = 1: Cathode current Note that the time until IKR returns to 1 differs according to the initial status of the cathode. flfl Video output RON, GON and BON are set to 1 and the video signal is output from Rout, Gout and Bout.

– 34 – CXA2000Q Bit0Bit1Bit2Bit3Bit4Bit5Bit6Bit7 Sub Address

• ·· 0 0 0 0 0 00 h
• ·· 0 0 0 0 1 01 h
• ·· 0 0 0 1 0 02 h
• ·· 0 0 0 1 1 03 h
• ·· 0 0 1 0 0 04 h
• ·· 0 0 1 0 1 05 h
• ·· 0 0 1 1 0 06 h
• ·· 0 0 1 1 1 07 h
• ·· 0 1 0 0 0 08 h
• ·· 0 1 0 0 1 09 h
• ·· 0 1 0 1 0 0A h
• ·· 0 1 0 1 1 0B h
• ·· 0 1 1 0 0 0C h
• ·· 0 1 1 0 1 0D h
• ·· 0 1 1 1 0 0E h
• ·· 0 1 1 1 1 0F h
• ·· 1 0 0 0 0 10 h
• ·· 1 0 0 0 1 11 h
• ·· 1 0 0 1 0 12 h
• ·· 1 0 0 1 1 13 h
• ·· 1 0 1 0 0 14 h
• ·· 1 0 1 0 1 15 h
• ·· 1 0 1 1 0 16 h
• ·· 1 0 1 1 1 17 h
• ·· 1 1 0 0 0 18 h
• ·· 1 1 0 0 1 19 h I2C bus power-on initial settings The initial settings listed here for power-on when VDRIVE starts to oscillate are reference values; the actual settings may be determined as needed according to the conditions under which the set is to be used. Register Table "*" Undefined Control Register

– 35 – CXA2000Q 3) Power-on initial settings The initial settings listed here for power-on when VDRIVE starts to oscillate are reference values; the actual settings may be determined as needed according to the conditions under which the set is to be used. PICTURE = 3Fh Max (User Control) TRAP OFF = 0 Chroma Trap ON VM OFF = 0 VM out ON HUE = 1Fh Center (User Control) DC-TRAN = 0 Y DC transmission ratio 100% D-PIC = 1 Y black expansion ON COLOR = 1Fh Center (User Control) TOT = 0 Chroma low frequency increased BRIGHT = 1Fh Center (User Control) D-COL = 1 Dynamic Color ON SHARPNESS = 7h Center (User Control) PRE-OVER = 0 Sharpness pre/over ratio 1:1 COLOR SW = 0 AUTO SUB-CONT = 7h Center (Adjust) TRAP F0 = 7h Center (Adjust) SUB-COLOR = 7h Center (Adjust) SUB-HUE = 7h Center (Adjust) SUB-BRIGHT = 1Fh Center (Adjust) GAMMA = 0 Gamma OFF G-DRIVE = 1Fh Center (Adjust) AGING = 0 Aging Mode OFF B-DRIVE = 1Fh Center (Adjust) INTERLACE = 0 INTERLACE mode G-CUTOFF = 7h Center (Adjust) B-CUTOFF = 7h Center (Adjust) RON = 0 Rch video output OFF GON = 0 Gch video output OFF BON = 0 Bch video output OFF PICON = 0 RGB all blanked VOFF = 0 Vdrive oscillation FHHI = 0 Horizontal oscillator frequency standard CD-MODE = 0 V countdown auto mode AKBOFF = 0 AKB ON V-SIZE = 1Fh Center (Adjust) V-FREQ = 0 AUTO V-POSITION = 1Fh Center (Adjust) AFC-MODE = 2 Center S-CORR = 7h Center (Adjust) V-LIN = 7h Center (Adjust) H-SIZE = 1Fh Center (Adjust) REF-POSI = 0 PIN-COMP = 1Fh Center (Adjust) VBLKW = 0

– 36 – CXA2000Q (Power-on initial settings cont.) H-POSITION = 7h Center (Adjust) PIN-PHASE = 7h Center (Adjust) AFC-BOW = 7h Center (Adjust) AFC-ANGLE = 7h Center (Adjust) SCP BGR = 1 Center SCP BGF = 1 Center XTAL = 0 AUTO EXT SYNC = 0 Internal SYNC CV/YC = 0 CV input V-ASPECT = 0h 16:9 CRT Full Mode ZOOMSW = 1 16:9 CRT HBLKSW = 1 Hblk width adjust ON V-SCROLL = 1Fh Center (User Control) JMPSW = 0 16:9 CRT Full Mode HSIZE SW = 0 Normal UP-VLIN = 7h 16:9 CRT Full Mode LO-VLIN = 7h 16:9 CRT Full Mode LEFT-BLK = Fh Hblk width Min. RIGHT-BLK = Fh Hblk width Min. EHT-H = 0 Hdrive high-voltage compensation OFF EHT-V = 3 Vdrive high-voltage compensation amount maximum CORNERPIN = 7h Center (Adjust) YS1 OFF = 0 Normal DL = 3 Normal (Adjust) 2. Various mode settings The CXA2000Q contains bus registers for deflection compensation which can be set for various wide modes. Wide mode setting registers can be used separately from registers for normal picture distortion adjustment, and once deflection adjustment has been performed in full mode, wide mode settings can be made simply by changing the corresponding register data.

• VDRIVE signal picture distortion adjustment registers V-SIZE, V-POSITION, S-CORR, V-LIN
• E/WDRIVE signal picture distortion adjustment registers H-SIZE, PIN-COMP, PIN-PHASE, CORNER-PIN
• Wide mode setting registers V-ASPECT, ZOOMSW, HBLKSW, V-SCROLL, JMPSW, HSIZESW, UP-VLIN, LO-VLIN, LEFT-BLK, RIGHT-BLK

– 37 – CXA2000Q Examples of various modes are listed below. These modes are described using 570 (NTSC: 480) lines as the essential number of display scanning lines. Wide mode setting register data is also listed, but settings may differ slightly due to IC variation. The standard setting data differs for 16:9 CRTs and 4:3 CRTs. Register 16:9 CRT 4:3 CRT V-ASPECT 0h 2Fh V-SCROLL 1Fh 1Fh ZOOMSW 1 0 UP-VLIN 0h 0h LO-VLIN 0h 0h JMPSW 0 0 HSIZESW 0 0 HBLKSW 0 0 LEFT-BLK 7h 7 RIGHT-BLK 7h 7h 1) 16:9 CRT full mode This mode reproduces the full 570 (NTSC:480) lines on a 16:9 CRT. 4:3 images are reproduced by stretching the picture to the left and right. Normal images are compressed vertically, but 16:9 images can be reproduced in their original 16:9 aspect ratio with a video source which compresses (squeezes) 16:9 images to 4:3 images. The register settings are the 16:9 CRT standard values. 2) 16:9 CRT normal mode In this mode, 4:3 images are reproduced without modification. A black border appears at the left and right of the picture. In this mode, the H deflection size must be compressed by 25% compared to full mode. The CXA2000Q permits compression with a register (HSIZESW) that compresses the H size by 25%. Because excessive current flows to the horizontal deflection coil in this case, adequate consideration must be given to the allowable power dissipation, etc., of the horizontal deflection coil in the design of the set. In addition, this concern can also be addressed through measures taken external to the IC, such as by switching the horizontal deflection coil. Full mode should be used when using memory processing to add a black border to the video signal. H blanking of the image normally uses the flyback pulse input to AFCPIN (Pin 38). However, the blanking width can be varied according to the control register setting when blanking is insufficient for the right and left black borders. The following three settings are added to the 16:9 CRT standard values for the register settings. HBLKSW = 1 LEFT-BLK = Adjustment value RIGHT-BLK = Adjustment value The H angle of deflection also decreases, causing it to differ from the PIN compensation amount during H size full status. Therefore, in addition to the wide mode registers, PIN-COMP must also be readjusted only for this mode. 3) 16:9 CRT zoom mode In this mode, 4:3 images are reproduced by enlarging the picture without other modification. The top and bottom of normal 4:3 images are lost, but almost the entire picture can be reproduced for vista size video software, etc. which already has black borders at the top and bottom. The enlargement ratio can be controlled by the V-ASPECT register, and enlarging the picture by 33% compared to full mode allows zooming to be performed for 4:3 images without distortion. In this case, the number of scanning lines is reduced to 430 lines compared to 570 lines for full mode. The zooming position can be shifted vertically by the V-SCROLL register. V blanking of the image normally begins from V sync and continues for 2H after the AKB reference pulse, and the top and bottom parts are also blanked during this mode. Adjust the following two registers with respect to the 16:9 CRT standard values for the register settings. V-ASPECT = 2Fh V-SCROLL = 1Fh or user control

– 38 – CXA2000Q 4) 16:9 CRT subtitle-in mode When CinemaScope size images which have black borders at the top and bottom of the picture are merely enlarged with the zoom mode in 3) above, subtitles present in the black borders may be lost. Therefore, this mode is used to super-compress only the subtitle part and reproduce it on the display. Add the LO-VLIN adjustment to the zoom mode settings for the register settings. V-ASPECT = 2Fh V-SCROLL = 1Fh or user control LO-VLIN = Adjustment value The LO-VLIN register causes only the linearity at the bottom of the picture to deteriorate. Therefore, UP-VLIN should also be adjusted if the top and bottom of the picture are to be made symmetrical. Since the picture is compressed vertically, the number of scanning lines exceeds 430 lines. 5) 16:9 CRT V compression mode This mode is used to reproduce two 4:3 video displays such as for PandP. The V size must be compressed to 67% in order to reproduce two displays on a 16:9 CRT without distortion using 480 scanning lines, and this can be set by JMPSW. Compression is performed after the AKB reference pulse, so the reference pulse remains in the overscan position. The V blanking width after the reference pulse becomes larger than normal and can be varied by the VBLKW register. During this mode, the bottom V blanking width is also expanded to 3H wider than normal so that the bottom of the picture is not overscanned. 16:9 CRT standard values are used with only the JMPSW setting changed for the register settings. JMPSW = 1 6) 16:9 CRT wide zoom mode This mode reproduces 4:3 video software naturally on wide displays by enlarging 4:3 images without other modification and compressing the parts of the image which protrude from the picture into the top and bottom parts of the picture. The display enlargement ratio is controlled by V-ASPECT, and the compression ratios at the top and bottom of the picture are controlled by UP-VLIN and LO-VLIN. Adjust the following three registers with respect to the 16:9 CRT standard values for the register settings. V-ASPECT = Adjustment value UP-VLIN = Adjustment value LO-VLIN = Adjustment value 7) 4:3 CRT normal mode This is the standard mode for 4:3 CRTs. The register settings are the 4:3 CRT standard values. 8) 4:3 CRT V compression mode This mode is used to reproduce M-N converter output consisting of 16:9 images expanded to a 4:3 aspect ratio and other squeezed signals without distortion on a 4:3 CRT. The V size must be compressed to 75% in order to reproduce a 4:3 squeezed signal at a 16:9 aspect ratio without any distortion. Compressing the V size with the JMPSW register used in mode 5) above, compresses the V size to 67%. Therefore, V-ASPECT is set to enlarge the V size by 8%. AKB reference pulse handling and V blanking are the same as for mode 5) above. 4:3 CRT standard values are used with the V-ASPECT and JMPSW settings changed for the register settings. V-ASPECT = 3Fh JMPSW = 1

– 39 – CXA2000Q Mode Settings 1)-1 1)-2 16:9 16:9 16:9 16:9 16:9 16:9 16:9 4:3 4:3 16:9 4:3 4:3 4:3 4:3 (16:9 + subtitle area) 4:3 4:3 4:3 16:9 16:9 CRT full Wide full 16:9 CRT normal 16:9 CRT zoom 16:9 CRT with subtitle area on 16:9 CRT V compression 16:9 CRT wide zoom 4:3 CRT normal 4:3 CRT V compression V-ASPECT = 0h: V size 75% V-ASPECT = 0h: V size 75% V-ASPECT = 0h: V size 75% HBLKSW = 1h: HBLK width adjustment ON LEFT-BLK = Adjustable RIGHT-BLK = Adjustable PIN-COMP = Adjustable (External support: H-DY H amplitude 75%) V-ASPECT = 2Fh: V size 100% ZOOMSW = 1h: Zoom ON V size limited at 75% V-SCROLL = 0h: Zoom bottom of video image 1Fh: Zoom center of video image 3Fh: Zoom top of video image Adjustable: Open to user V-ASPECT = 2Fh: V size 100% UP-VLIN = Adjustable: Slightly compresses top of video image LO-VLIN = Adjustable: Significantly compresses bottom of video image ZOOMSW 1h: V size limited at 75% (V-SCROLL = Adjustable) V-ASPECT = 0h: V size 75% JMPSW = 1h: Reference pulse skipping ON V size compressed 67% after the reference pulse (compressed to 50% total) VBLKW = Adjustable: VBLK width expanded at top and bottom of video image V-ASPECT = Adjustable: V size 90% UP-VLIN = Adjustable: LO-VLIN = Adjustable: (S-CORR = Adjustable): V-ASPECT = 2Fh: V size 100% V-ASPECT = 3Fh: V size 112% JMPSW = 1h: Reference pulse skipping ON (compressed to 75% total) VBLKW = Adjustable: VBLK width expanded at top and bottom of video image Setting CRT SIZE SOFT SIZE MODE NAME I 2C BUS REGISTER * The amount of picture distortion compensation in a vertical direction position of the CRT does not change in response to the above modes; as a result, the initial values of each picture distortion register can be used as is. Compression of top and bottom of video image

– 40 – CXA2000Q 3. Signal processing The CXA2000Q is comprised of sync signal processing, H deflection signal processing, V deflection signal processing, and Y/C/RGB signal processing blocks, all of which are controlled by the I2C bus. 1) Sync signal processing Pin 48 (SYNC OUT) outputs at 2Vp-p either the internal signal (CVIN/YIN) selected by the internal video switch, or the external sync signal input from Pin 56 (EXT SYNC IN). This selection is controlled by the I 2C bus. The signal output from Pin 48 is buffered by a PNP Tr. and is then input to HSIN (Pin 47) or VSIN (Pin 46) through a suitable filter. The Y signals input to Pins 46 and 47 are sync separated by the horizontal and vertical sync separation circuits. The resulting horizontal sync signal and the signal (FH = 15625Hz or 15734Hz) obtained by frequency dividing the 32FH-VCO output using the ceramic oscillator (frequency 500kHz or 503.5kHz) by 32 are phase- compared, the AFC loop is constructed, and an H pulse synchronized with the H sync is generated inside the IC. Adjustment of the H oscillator frequency is unnecessary. When the AFC is locked to the H sync, 1 is output to the status register (HLOCK) and that can be used to detect the presence of the video signal. The vertical sync signal is sent to the V countdown block where the most appropriate window processing is performed to obtain V sync timing information which resets the counter. AKB and other V cycle timing are then generated from this reset timing. 2) H deflection signal processing The H pulse obtained through sync processing is phase-compared with the H deflection pulse input from Pin 38 to control the phase of the HDRIVE output and the horizontal position of the image projected on the CRT. In addition, the compensation signal generated from the V sawtooth wave is superimposed, and the vertical picture distortion is compensated. The H deflection pulse is used to H blanking of the video signal. When the pulse input from Pin 38 has a narrow width, the pulse generated by the IC can be added to the H deflection pulse and used as the H blanking pulse (HBLKSW). Pin 38 is normally pulse input, but if the pin voltage drops to the GND level, HDRIVE output stops and 1 is output to the status register (XRAY). To release this status, turn the power off and then on again. 3) V deflection signal processing The V sawtooth wave is generated at the cycle of the reset pulse output from the countdown system. After performing wide deflection processing for this sawtooth wave, picture distortion adjustment is performed by the VDRIVE and E/WDRIVE function circuits and the signal is output as the VDRIVE and E/WDRIVE signals. 4) Y signal processing Either CVIN, input from Pin 53, or YIN, output from Pin 55, is selected by the video switch and then is passed to the Y signal processing circuit as the Y signal. The input level is 1Vp-p. The Y signal passes through the subcontrast control, the trap for eliminating the chroma signal, the delay line, the sharpness control, the clamp and the black expansion circuits, and is then output to Pin 5 as YOUT. The differential waveform of the Y signal, advanced for about 200ns from YOUT is output from Pin 49 as the VM signal. The delay time is set by the bus register (DL). When CVIN is selected, the trap is on; when YIN is selected, the trap is off. The f0 of the internal filter is automatically adjusted within the IC. Because the f0 of the filter is not specified when the color killer function is operating, turn the trap off if there are any difficulties. In addition, the f0 of the trap will be affected slightly by variations among IC, so fine adjustment through the I 2C bus (TRAP-F0) may be required.

– 41 – CXA2000Q 5) C signal processing The CVBS signal or chroma signal (specified input level: burst level of 300mVp-p) selected by the video switch passes through the ACC, TOT, chroma amplifier and demodulation circuits, becomes the R-Y and B-Y color difference signals, and is inverted for output on Pins 3 and 4. The color difference signals are averaged together by the external 1H delay line, and are input to Pins 7 and 8. Both color difference signals are clamped together with the Y signal input to Pin 5. They are then combined with the G-Y signal in the color control and axis control circuits. After Y/C mixing, the signals become the RGB signals. If the burst level goes to –35dB or less with respect to the specified input level, the color killer operates. In addition, the color system (PAL/NTSC) and the subcarrier frequency (4.43MHz/3.58MHz) are automatically identified according to the input chroma signal, and the internal VCO, demodulation circuit, axis control circuit, etc., are adjusted automatically. Furthermore, SECAM signals can also be identified if an external SECAM decoder is connected to Pin 1. In this case, Pins 3 and 4 and the SECAM decoder color difference output are linked together directly, and automatically one side goes to high impedance, the other goes to low impedance according to the input chroma signal, and then they are input to the external 1H delay line. System identification can be set to automatic or forced mode by the I 2C bus (XTAL and COLOR SW). The color system is output to the status register (COLOR SYS). 6) RGB Signal processing The RGB signals obtained from the Y/C block pass through the half-tone switch circuit (YM SW), the two switch circuits for the external RGB signals (YS1, YS2 SW), the picture control, dynamic color, gamma compensation, clamp, brightness control, drive adjustment, cut-off adjustment and auto cut-off circuits, and are output to Pins 22, 24 and 26. The RGB signals input to Pins 12, 13, 14, 17, 18, and 19 are 100 IRE, 100% white 0.7Vp-p signals, in accordance with the standard for normal video signals. If signals of 1.5Vp-p or more are input to Pins 17, 18, and 19, 67 IRE output is obtained (digital input). The voltage applied to Pin 28 (ABLIN) is compared with the internal reference voltage, integrated by the capacitor which is connected to Pin 29, and performs picture control and brightness control. In order to adjust the white balance (black balance), this IC has a drive control function which adjusts the gain between the RGB outputs and a cut-off control function which adjusts the DC level between the RGB outputs. Both drive control and cut-off control are adjusted by the I 2C bus, with the Rch fixed and the G and Bch variable. An auto cut-off function (AKB) which forms a loop between the IC and CRT and performs adjustment automatically has also been added. This function can compensate for changes in the CRT with time. Auto cut- off operation is as follows.

• R, G and B reference pulses for auto cut-off, shifted 1H each in the order mentioned, appear at the top of the picture (actually, in the overscan portion). The reference pulse uses 1H in the V blanking interval, and is output from each R, G and B output pin.
• The cathode current (Ik) of each R, G and B output is converted to a voltage and input to Pin 27.
• The voltage input to Pin 27 is compared with the reference voltage in the IC, and the current generated by the resulting error voltage charges the capacitors connected to Pins 21, 23 and 25 for the reference pulse interval and is held during all other interval.
• The loop functions to change the DC level of the R, G and B outputs in accordance with the capacitor pin voltage so that the Pin 27 voltage matches the reference voltage in the IC. The Rch for the reference voltage in the IC is fixed and the G and Bch are cut-off controlled by the I 2C bus. During G/B-CUTOFF center status, the loop functions so that the Rch for the reference pulse input to Pin 27 is 1Vp-p and the G and Bch are 0.81Vp-p. The reference pulse timing can be varied by the I 2C bus. When AKB is not used, the IC can be set to manual cut-off mode with I2C bus settings. In this case, the DC level of the R, G and B outputs can be varied by applying voltages independently to Pins 21, 23 and 25.

– 42 – CXA2000Q 4. Notes on operation Because the RGB signals and deflection signals output from the CXA2000Q are DC direct connected, the board pattern must be designed consideration given to minimizing interference from around the power supply and GND. Do not separate the GND patterns for each pin; a solid earth is ideal. Locate the power supply side of the by- pass capacitor which is inserted between the power supply and GND as near to the pin as possible. Also, locate the XTAL oscillator, ceramic oscillator and IREF resistor as near to the pin as possible, and do not wire signal lines near this pin. Drive the Y, external Y/color difference and external RGB signals at a sufficiently low impedance, as these signals are clamped when they are input using the capacitor connected to the input pin. DC bias is applied to the chroma signal within the IC. Input the chroma signal with low impedance via an external capacitor. Use a resistor (such as a metal film resistor) with an error of less than 1% for the IREF pin. Use a capacitor, such as an MPS (metalized polyester capacitor) with a small tan d for SAWOSC. When using a line frequency FH of 15625Hz for the main clock (PAL-B, G, etc.), Murata's Ceralock CSB500F63 is recommended. This will yield a free-run frequency in the neighborhood of 15625Hz.

– 43 – CXA2000Q Curve Data I2C bus data conforms to the "I2C Bus Register Initial Settings" of the Electrical Characteristics Measurement Conditions (P. 22). V-SIZE Time [ms] 0 5 10 15 20 2.0 V [V] 4.0 3.5 3.0 2.5 V-SIZE = 0 V-SIZE = 1F V-SIZE = 3F V-POSITION Time [ms] 0 5 10 15 20 2.4 V [V] 3.6 3.4 3.2 3.0 2.8

2.6 V-POSITION = 0

V-POSITION = 1F V-POSITION = 3F V-SCROLL Time [ms] 0 5 10 15 20 2.4 V [V] 3.8 3.4 3.2 3.0 2.8 2.6 3.6 V-SCROLL = 0 V-SCROLL = 1F V-SCROLL = 3F 2.4 S-CORR Time [ms] 0 5 10 15 20 2.4 V [V] 3.6 3.4 3.2 3.0 2.8

2.6 S-CORR = 0

S-CORR = 7 S-CORR = F V-LIN Time [ms] 0 5 10 15 20 2.4 V [V] 3.6 3.4 3.2 3.0 2.8

2.6 V-LIN = 0

V-LIN = 7 V-LIN = FV-ASPECT Time [ms] 0 5 10 15 20 2.2 V [V] 3.8 3.4 3.2 3.0 2.8 2.6 V-ASPECT = 0 V-ASPECT = 1F V-ASPECT = 3F 3.6 2.4

– 44 – CXA2000Q PIN-COMP Time [ms] 0 5 10 15 20 3.0 V [V] 4.2 4.0 3.8 3.6 3.4

3.2 PIN-COMP = 0

PIN-COMP = 1F PIN-COMP = 3F UP-VLIN Time [ms] 0 5 10 15 20 2.4 V [V] 3.6 3.4 3.2 3.0 2.8

2.6 UP-VLIN = 0

UP-VLIN = 7 UP-VLIN = F LO-VLIN Time [ms] 0 5 10 15 20 2.4 V [V] 3.6 3.4 3.2 3.0 2.8

2.6 LO-VLIN = 0

LO-VLIN = 7 LO-VLIN = F PIN-PHASE Time [ms] 0 5 10 15 20 3.3 V [V] 4.1 3.9 3.8 3.7 3.6 3.5 PIN-PHASE = 0 PIN-PHASE = 7 PIN-PHASE = F 4.0 3.4 CORNER-PIN Time [ms] 0 5 10 15 20 3.2 V [V] 4.2 3.8 3.6 3.4 CORNER-PIN = 0 CORNER-PIN = 7 CORNER-PIN = F 4.0 H-SIZE Time [ms] 0 5 10 15 20 V [V] 4.8 4.4 4.0 3.6 3.2 H-SIZE = 0 H-SIZE = 1F H-SIZE = 3F

– 45 – CXA2000Q PICTURE DATA 0 2 04 06 0 7 0 –20 Gain [dB] –10 –15 10 30 50 COLOR DATA 02 0 4 0 6 0 7 0 –20 Gain [dB] –10 –15 10 30 50 ∗ COLOR OFF when DATA = 0 (–40dB or less) DL DATA 02468 200 CVIN – YOUT delay time [ns] 800 700 600 500 400 300 1357 H-POSITION DATA 048 1 2 1 6 Time [µs] 2 6 10 14 SYNC center t [µsec] 6µsec 12µsec HSIN AFCPIN SHARPNESS Frequency [MHz] 048 1 2 –10 Gain [dB] SHARPNESS = 0 SHARPNESS = 7 SHARPNESS = F 26 1 0 TRAP OFF Frequency [MHz] 0246 –30 Gain [dB] –10 –15 –20 –25 135 3.58MHz TRAP OFF = 0 4.43MHz TRAP OFF = 0 TRAP OFF = 1

– 46 – CXA2000Q SUB-CONT DATA 048 1 2 Gain [dB] 2 6 10 14 Gain [dB] B-DRIVE, G-DRIVE DATA 0 2 04 06 0 7 010 30 50 DATA Gain [dB] SUB-COLOR 048 1 2 1 62 6 10 14 BRIGHT DATA 02 0 4 0 6 0 7 0 –1.5 Potential difference between Rch reference pulse leveland black level [Vp-p] 0.5 10 30 50 SUB-BRIGHT = 0 SUB-BRIGHT = 1F SUB-BRIGHT = 3F –1.0 –0.5 SUB-BRIGHT DATA 0 2 04 06 0 7 0 –0.8 Potential difference between Rch reference pulse leveland black level [Vp-p] 0.2 –0.4 10 30 50 –0.6 –0.2 GAMMA CVIN input amplitude [IRE] 0 20 40 80 100 1.5 Rch output [V] 4.5 3.0 4.0 3.5 2.0 2.5 GAMMA = 0 GAMMA = 1 GAMMA = 2 GAMMA = 3

– 47 – CXA2000Q G-CUTOFF, B-CUTOFF DATA 04 1 6 2.6 IKIN reference pulse voltage [V] 4.2 3.8 61 2 4.0 81 410 2.8 3.0 3.2 3.4 3.6 Gch, Bch IK clamp level Rch AKB open loop characteristics Voltage applied to R, G and B sample-and-hold capacitance pins [V] 3.0 6.0 V [V] 3.5 1.5 3.5 4.0 5.0 0.5 2.5 5.54.5 3.0 1.0 2.0 Reference pulse voltage (AKBOFF = 0) RGBOUT black level voltage (AKBOFF = 0, 1)

– 48 – CXA2000Q Package Outline Unit: mm SONY CODE EIAJ CODE JEDEC CODE QFP-64P-L01 ∗QFP064-P-1420-A PACKAGE STRUCTURE PACKAGE MATERIAL LEAD TREATMENT LEAD MATERIAL PACKAGE WEIGHT

42 ALLOY

1.5g 64PIN QFP (PLASTIC) 23.9 ± 0.4 + 0.4 51 33 1.0 0.8 ± 0.2 16.3 + 0.1 17.9 ± 0.4 0.15 – 0.05 + 0.2 0.1 – 0.05 + 0.35 2.75 – 0.15 + 0.15 0.4 – 0.1 20.0 – 0.1 0.15 M± 0.12 + 0.4 14.0 – 0.1