CPB600PS3V3 XPPOWER | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 2

Technical content

Low Profile (61mm) Wide Output Voltage Adjustment Remote ON/OFF Power Good Signal Remote Sense Peak Current Available Input Input Voltage • 95-264 VAC (120-370 VDC) Input Frequency • 47-63 Hz Input Current • 8.2 A max at 115 VAC Inrush Current • 40 A max at 230 VAC Power Factor • 0.98/0.95 at 115/230 VAC Earth Leakage • 0.75 mA max at 230 VAC 60 Hz Current Output Output Voltage • See Table Output Voltage • See Table Adjustment Minimum Load • No minimum load required Start-Up Time • 400 ms typical at 230 VAC, 100% load Hold-up Time • 20 ms typical at 100% load Drift • ±0.4% max Line Regulation • ±0.5% max Load Regulation • ±1.0% max 0-100% load Ripple & Noise • ± 1% max pk-pk 20 MHz bandwidth Overvoltage • 110-130% of Vnom Protection Recycle input to reset Overload Protection • Operates at 105% of rated current (101% of pk rating), <5 s auto recovery >5 s recycle input to reset Temperature • ±1.25% max -20 °C to +50 °C Coefficient Overtemperature • Operates in the event of fan failure Protection or if the operating temperature/ derating criteria is exceeded Remote Sense • Compensates for 0.3 V drop max If not required sense terminals must be connected locally ie: +S to +M and -S to -M on CN1 Remote ON/OFF • 12 V 3 mA applied between RCG & RC2 will inhibit the output of the unit & the fan General Efficiency • See Table Isolation • 3000 VAC Input to Output

2000 VAC Input to Ground

500 VAC Output to Ground

Switching Frequency • 130kHz PFC, 330 kHz PWM Environmental Operating • -20 °C to +70 °C, derate linearly above Temperature +50 °C to 50% at +70°C Storage • -20 °C to +75 °C Temperature Relative Humidity • 20-90% non condensing Shock • 20 G 11 ms, once each x, y and z axis Vibration • 2 G 10-55Hz for 3 min periods for 60 min along each x, y and z axis EMC & Safety Emissions • EN55022 Level B conducted EN55022 Level A radiated ESD • EN61000-4-2 Level 2 contact, Susceptibility Level 3 air Radiated • EN61000-4-3 Level 3 Susceptibility EFT/Burst • EN61000-4-4 Level 3 Surge • EN61000-4-5 Level 3 line to line Level 4 line to ground Safety Approvals • UL60950, C-UL (CSA 60950) EN60950 400-650 Watts CPB600 Series AC-DC Chassis Mount Specification THE XP ERTS IN POWER www.xpplc.com sales@xpplc.com

www.xpplc.com sales@xpplc.com Output Current Regulation Ripple Efficiency (3) Model Voltage Max Peak Line Load Noise (2) 3.3 V (2.64-3.96) 120 A - 20 mV 40 mV 120 mV 72% CPB600PS3V3 5.0 V (3.96-6.00) 120 A - 20 mV 40 mV 120 mV 77% CPB600PS05 7.5 V (5.25-8.25) 80 A - 36 mV 60 mV 150 mV 79% CPB600PS7V5 12.0 V (8.25-13.2) 53 A - 48 mV 100 mV 150 mV 82% CPB600PS12 15.0 V (10.50-16.5) 43 A - 60 mV 120 mV 150 mV 82% CPB600PS15 24.0 V (16.5-26.4) 27 A 31 A (1) 96 mV 150 mV 150 mV 84% CPB600PS24 36.0 V (25.2-39.6) 18 A 144 mV 150 mV 200 mV 84% CPB600PS36 48.0 V (38.4-56.0) 13 A - 192 mV 300 mV 200 mV 83% CPB600PS48 OUTPUT VOLTAGE & CURRENT RATINGS CPB 1. Peak current duration 100 ms max with a duty cycle ≤35% 170-264 VAC only. 2. Measured over a 20 MHz bandwidth and from 0 °C to +50 °C. 3. Measured at nominal 230 VAC input and 100% load. Notes CN3 PIN CONNECTIONS Pin Function 1 -S - Remote Sensing 2 -S - Remote Sensing 3 AUX Auxiliary Output (12 V/0.1A)

4 RC1 Remote ON/OFF

5 AUXG AUX Ground

6 N.C. No Connection

7 PG Power Good Signal

8 PGG Power Good Ground

Mating Connector & Terminal for CN1, CN2 & CN3 Connector Mating Terminal Mfr Connector CN1 S10B-PHDSS PHDR-10VS Reel SPHD-002T-P0.5 CN2 Loose BPHD-001T-P0.5 J.S.T CN3 S8B-PHDSS PHDR-8VS BPHD-002T-P0.5 Output Voltage Adjustment 60-110% of the rated output voltage is achieved by: 1. Using on-board potentiometer. 2. Applying a voltage externally between TRM & -S on CN1 or CN2. 3. Connecting a resistor externally between TRM & -S on CN1 or CN2. The external voltage level is calculated below & should not be less than -0.7 V or more than 3.0 V. External Trim Voltage = Required Vout x 2.5 Vnom Weight 3.4kg CN1/CN2 PIN CONNECTIONS Pin Function 1 +M + Output Voltage Monitoring 2 +S + Remote Sensing 3 -M - Output Voltage Monitoring 4 -S - Remote Sensing

5 VB Voltage Balance

6 CB Current Balance

7 TRM Adjustment of Output Voltage

9 RC2 Remote ON/OFF

10 RCG Remote ON/OFF Ground

Rev 2.0