CPB1KPS3V3 XPPOWER | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 3

Technical content

  • Universal PFC Input
  • Low Profile (61 mm)
  • Wide Output Voltage Adjustment
  • Remote On/Off
  • Power Good Signal
  • Remote Sense
  • Peak Current Available CPB1K/1K5 Series Input Input Voltage • 85-264 VAC (120-370 VDC) Input Frequency • 47-63 Hz Input Current • 19 A at 115 VAC Inrush Current • 40 A at 230 VAC Power Factor • 0.98/0.95 at 115/230 VAC Earth Leakage Current • 1.5 mA max at 230 VAC/60Hz Output Output Voltage • See tables Output Voltage Trim • See tables Minimum Load • No minimum load required Start Up Time • 400 ms typical at 230 VAC, 100% load Hold Up Time • 20 ms typical at 100% load Drift • ±0.4% max Line Regulation • ±0.5% max Load Regulation • ±1.0% max 0-100% load Ripple & Noise • ±1.0% pk-pk, 20MHz BW Overvoltage Protection • 110-130% Vnom, recycle input to reset Overtemperature • Operates in the event of fan failure or if Protection the operating temperature / derating criteria is exceeded Overload Protection • Operates at 105% of rated current (101% of pk rating), <5 s auto recovery, >5 s recycle input to reset Temperature • ±1.25% max -20 ºC to +50 ºC Coefficient Remote Sense • Compensates for up to 0.3 V drop max if not required, sense teminals must be connected locally i.e +S to +M and -S to -M on CN1 Remote On/Off • 12 V 3 mA applied between RCG & RC2 will inhibit the output of the unit and the fan xppower.com General Efficiency • See tables Isolation • 3000 VAC Input to Output

2000 VAC Input to Ground

500 VAC Output to Ground

Switching Frequency • 130 kHz PFC, 200 kHz PWM Environmental Operating Temperature • -20 ºC to +70 ºC, derate linearly from +50 ºC to 50% at +70 ºC Relative Humidity • 20-90% non-condensing Storage Temperature • -20 ºC to +75 ºC Shock • 20 G 11 ms, once each x, y and z axis Vibration • 2 G, 10 Hz to 55 kHz, 3 min periods for 60 min along each x, y and z axis EMC & Safety Emissions • EN55022, level B conducted EN55022, level A radiated ESD Immunity • EN61000-4-2, level 2 contact, level 3 air Radiated Immunity • EN61000-4-3, level 3 EFT/Burst • EN61000-4-4, level 3 Surge • EN61000-4-5, level 3 line to line, level 4 line to ground Safety Approvals • EN60950, UL60950, cUL (CSA 60950) AC-DC

1 +M + Output Voltage Monitoring 2 +S + Remote Sensing 3 -M - Output Voltage Monitoring 4 -S - Remote Sensing

5 VB Voltage Balance

6 CB Current Balance

7 TRM Adjustment of Output Voltage

9 RC2 Remote On/Off

10 RCG Remote On/Off Ground

3 AUX Auxiliary Output (12V/0.1A)

4 RC1 Remote On/Off

5 AUXG AUX Ground

6 N.C No Connection

7 PG Power Good Signal

8 PGG Power Good Ground

Mating Connector & Terminal - CN1, CN2 & CN3 Connector Mating Connector Terminal Manufacturer CN1 S10B-PHDSS PHDR-10VS Reel SPHD-002T-P0.5 Loose BPHD-001T-P0.5 BPHD-002T-P0.5 J.S.TCN2 CN3 S8B-PHDSS PHDR-8VS Models and Ratings Input Voltage Current Regulation Ripple & Noise(2) Efficiency(3) Model NumberMax Peak Line Load 3.3 V (2.64 - 3.96) 200 A - 20 mV 40 mV 120 mV 76% CPB1KPS3V3 5.0 V (3.96 - 6.00) 200 A - 20 mV 40 mV 120 mV 81% CPB1KPS05 7.5 V (5.25 - 8.25) 134 A - 36 mV 60 mV 150 mV 83% CPB1KPS7V5 12 V (8.25 - 13.20) 88 A - 48 mV 100 mV 150 mV 84% CPB1KPS12 15 V (10.50 - 16.50) 70 A - 60 mV 120 mV 150 mV 84% CPB1KPS15 24 V (16.50 - 26.40) 44 A 51 A (1) 96 mV 150 mV 150 mV 86% CPB1KPS24 36 V (25.20 - 39.60) 29 A - 114 mV 150 mV 200 mV 86% CPB1KPS36 48 V (38.40 - 56.00) 22 A - 192 mV 300 mV 200 mV 86% CPB1KPS48 Notes 1. Peak current duration 10 s max with duty cycle ≤ 35% 170-264 VAC only. 2. Measured over a 20 MHz bandwidth from 0 ºC to +50 ºC. 3. Measured at nominal 230 VAC input and 100% load. CN1 CN3 CN2 AC(N) AC(L) LED 8-M4 Mounting Hole (Bothsides) Input terminal cover Output voltage adjustable potentiometer Output terminal(+ ) Output terminal(- ) AIR FLOW 2-M4 2-º 9 Nameplate C AGF ) L(C A

1 N C

H ) N(

3 N C

2 N C

J D A. V Mounting Hole (Bottom sides) 4-M4 )81( 15.85 51.25 )52( 240 6 max 051 25max (35) )5.7(931 29 165± 0.5 5.11 83 ± 5.0 57.401)42( 011 ± 5.0 29 165± 0.5 5.2 FG( ) Notes: 1. Tolerance: ±1. 2. Weight: 2.2 Kg. 3. Dimensions in mm. Peak Current Conditions:

  • 170-264 VAC
  • t1 ≤ 10 s
  • lp ≤ Rated peak current
  • lave ≤ Rated current t1 +t 2 O u t p u t C u r r e n t (A ) Peak Current t lp (Peak Current) lave (AverageCurrent) t

04 AUG 05

1 +M + Output Voltage Monitoring 2 +S + Remote Sensing 3 -M - Output Voltage Monitoring 4 -S - Remote Sensing 3 AUX Auxiliary Output (12V/0.1A) 6 N.C No Connection Mating Connector & Terminal - CN1, CN2 & CN3 Connector Mating Connector Terminal Manufacturer CN1 S10B-PHDSS PHDR-10VS Reel SPHD-002T-P0.5 Loose BPHD-001T-P0.5 BPHD-002T-P0.5 J.S.TCN2 CN3 S8B-PHDSS PHDR-8VS Input Voltage Current Regulation Ripple & Noise(3) Efficiency(4) Model Number(3) Max Peak Line Load 3.3 V (2.64 - 3.96) 300 A - 20 mV 40 mV 120 mV 75% CPB1K5PS3V3 5.0 V (3.96 - 6.00) 300 A - 20 mV 40 mV 120 mV 81% CPB1K5PS05 7.5 V (5.25 - 8.25) 200 A - 36 mV 60 mV 150 mV 81% CPB1K5PS7V5 12 V (8.25 - 13.20) 125 A - 48 mV 100 mV 150 mV 82% CPB1K5PS12 15 V (10.50 - 16.50) 100 A - 60 mV 120 mV 150 mV 86% CPB1K5PS15 24 V (16.50 - 26.40) 70 A (1) 105 A (2) 96 mV 150 mV 150 mV 86% CPB1K5PS24 36 V (25.20 - 39.60) 47 A (1) 70 A (2) 114 mV 150 mV 200 mV 86% CPB1K5PS36 48 V (38.40 - 56.00) 35 A (1) - 192 mV 300 mV 200 mV 86% CPB1K5PS48 Notes 1. At low input voltage i.e. 115 V nom derate to 65 A, 42 A and 32 A. 2. Peak current duration 10 s max with duty cycle ≤ 35% 170-264 VAC only. 3. Measured over a 20 MHz bandwidth from 0 ºC to +50 ºC. 4. Measured at nominal 230 VAC input and 100% load. Name plate ) N( J D A. V GF C N CA ) L( CA1 N C 2-º 9 CN3 CN2 NC AC(N) AC(L) Output voltage adjustable potentiometer AIRFLOW 8-M4 8-M4 Mounting Hole (Bothsides) Input terminal cover Outputterminal(+) Outputterminal(-) LED 701 93101 )5.7( 15.85 )52()81( 1510 4 )42( 231 171.5±0.519 4.251 ± 5.0 268 6max 871 19 171.5±0.5 5.11 83 ± 5.0 (45) 8.21 25max 51.25 FG( ) Mounting Hole (Bothsides) Notes: 1. Tolerance: ±1. 2. Weight: 3.4 Kg. 3. Dimensions in mm. Output Voltage Adjustment 60-110% of the rated output voltage is achieved by: 1. Using on-board potentiometer 2. Applying a voltage externally between TRM & -S on CN1 or CN2 3. Connecting a resistor externally between TRM & -S on CN1 or CN2 The external voltage level is calculated below and should not be less than -0.7 V or more than 3.0 V. External Trim Voltage = Peak Current Conditions:

  • 170-264 VAC
  • t1 ≤ 10 s
  • lp ≤ Rated peak current
  • lave ≤ Rated current t1 +t 2 Required Vout x 2.5 Vnom O u t p u t C u r r e n t (A ) Peak Current t lp (Peak Current) lave (AverageCurrent) t