CMY91

CMY91 SIEMENS | Alldatasheet

Document overview

• Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
• PDF pages: 9

Technical content

Siemens Aktiengesellschaft pg. 1/9 16.12.96 HL EH PD21 D a t a s h e e t * GaAs mixer with integrated IF-amplifier for mobile communication * Frequency range 0.8 GHz to 2.5 GHz * Very low power consumption (1mA typ.) * Single positive supply voltage * Operating voltage range: 2.7 to 6 V * Miniature package MW6 based on SOT23 ESD: Electrostatic discharge sensitive device, observe handling precautions! LO GND RF CAP GND IF Type Marking Ordering code (taped) Package 1) CMY 91 M2 Q62702-M9 MW-6 RF(in)[6] CAP(1)[1] IF(out)[3] LO(in)[4] GND[2;5] Maximum ratings Symbol Unit Drain-source voltage V IF-GND 8V Gate-source voltage range V LO-GND -5 ... 0 V Drain current I IF 20 mA RF- / LO-peak current +I RF, +ILO 2m A Channel temperature T Ch 150 °C Storage temperature range T stg -55...+150 °C Total power dissipation (TS = tbd °C)2) Ptot 160 mW Thermal resistance Channel-soldering point GND R thChS 350 K/W 1) Dimensions see chapter Package Outlines 2) TS: Temperature measured at soldering point GND

Siemens Aktiengesellschaft pg. 2/9 16.12.96 HL EH PD21 Electrical characteristics at TA = 25°C / VD = 3 V unless otherwise specified Characteristics of 900MHz test and application circuit (see page app. circuit) Parameters Symbol min typ max Unit Drain-source breakdown voltage IIF = 500 µA V LO-GND = 0 V VRF-GND = 4 V CAP-pin not connected V(BR) IF-GND 8- -V Drain current VRF-GND = 0 V V LO-GND = 0 V VIF-GND = 3 V CAP-pin not connected ID 0.8 1 1.4 mA Conversion gain fRF = 920 MHz f LO = 965 MHz fIF = 45 MHz P LO = -3 dBm G C - 5.5 - dB Single sideband noise figure fRF = 920 MHz f LO = 965 MHz fIF = 45 MHz P LO = -3 dBm FSSB -9- d B 3rd order intermodulation fRF = 920 MHz f LO = 965 MHz fIF = 45 MHz P LO = -3 dBm IP3 - -2 - dBm LO/RF isolation f = 965 MHz IsoLO/RF -1 1-d B TA = 25°C / VD = 3 V; CAP-pin connected to ground by 680Ω resistor Parameters Symbol min typ max Unit Drain current VRF-GND = 0 V V LO-GND = 0 V VIF-GND = 3 V ID - 2.5 - mA Conversion gain fRF = 920 MHz f LO = 965 MHz fIF = 45 MHz P LO = -3 dBm G C - 9.5 - dB Single sideband noise figure fRF = 920 MHz f LO = 965 MHz fIF = 45 MHz P LO = -3 dBm FSSB - 8.0 dB 3rd order intermodulation fRF = 920 MHz f LO = 965 MHz fIF = 45 MHz P LO = -3 dBm IP3 - 0 - dBm LO/RF isolation f = 965 MHz IsoLO/RF -1 1-d B Not used ports were terminated by 50 Ω . Please make sure that LO-signal is clean of noise and spurious at f = fLO +/- fIF

Siemens Aktiengesellschaft pg. 3/9 16.12.96 HL EH PD21 Electrical characteristics at TA = 25°C / VD = 3 V unless otherwise specified Characteristics of 1450MHz application circuit (see page app. circuit) Parameters Symbol min typ max Unit Drain-source breakdown voltage IIF = 500 µA V LO-GND = 0 V VRF-GND = 4 V CAP-pin not connected V(BR) IF-GND 8--V Drain current VRF-GND = 0 V V LO-GND = 0 V VIF-GND = 3 V CAP-pin not connected ID 0.8 1 1.4 mA Conversion gain fRF = 1450 MHz fLO = 1350 MHz fIF = 100 MHz P LO = -3 dBm G C - 5.5 - dB Single sideband noise figure fRF = 1450 MHz fLO = 1350 MHz fIF = 100 MHz P LO = -3 dBm FSSB -1 0-d B 3rd order intermodulation fRF = 1450 MHz fLO = 1350 MHz fIF = 100 MHz P LO = -3 dBm IP3 - -2 - dBm LO/RF isolation f = 1350 MHz IsoLO/RF -8- d B TA = 25°C / VD = 3 V; CAP-pin connected to ground by 680Ω resistor Parameters Symbol min typ max Unit Drain current VRF-GND = 0 V V LO-GND = 0 V VIF-GND = 3 V ID - 2.5 - mA Conversion gain fRF = 1450 MHz fLO = 1350 MHz fIF = 100 MHz P LO = -3 dBm G C - 7.5 - dB Single sideband noise figure fRF = 1450 MHz fLO = 1350 MHz fIF = 100 MHz P LO = -3 dBm FSSB - 9.5 - dB 3rd order intermodulation fRF = 1450 MHz fLO = 1350 MHz fIF = 100 MHz P LO = -3 dBm IP3 - 0 - dBm LO/RF isolation f = 1350 MHz IsoLO/RF -8- d B Not used ports were terminated by 50 Ω .

Siemens Aktiengesellschaft pg. 4/9 16.12.96 HL EH PD21 Electrical characteristics at TA = 25°C / VD = 3 V unless otherwise specified Characteristics of 1900MHz application (see page app. circuit) Parameters Symbol min typ max Unit Drain-source breakdown voltage IIF = 500 µA V LO-GND = 0 V VRF-GND = 4 V CAP-pin not connected V(BR) IF-GND 8- -V Drain current VRF-GND = 0 V V LO-GND = 0 V VIF-GND = 3 V CAP-pin not connected ID 0.8 1 1.4 mA Conversion gain fRF = 1900 MHz fLO = 1800 MHz fIF = 100 MHz P LO = -3 dBm G C -5- d B Single sideband noise figure fRF = 1900 MHz fLO = 1800 MHz fIF = 100 MHz P LO = -3 dBm FSSB - 10.5 - dB 3rd order intermodulation fRF = 1900 MHz fLO = 1800 MHz fIF = 100 MHz P LO = -3 dBm IP3 - -2 - dBm LO/RF isolation f = 1800 MHz IsoLO/RF -8- d B TA = 25°C / VD = 3 V; CAP-pin connected to ground by 680Ω resistor Parameters Symbol min typ max Unit Drain current VRF-GND = 0 V V LO-GND = 0 V VIF-GND = 3 V ID - 2.5 - mA Conversion gain fRF = 1900 MHz fLO = 1800 MHz fIF = 100 MHz P LO = -3 dBm G C - 7.5 - dB Single sideband noise figure fRF = 1900 MHz fLO = 1800 MHz fIF = 100 MHz P LO = -3 dBm FSSB - 9.5 - dB 3rd order intermodulation fRF = 1900 MHz fLO = 1800 MHz fIF = 100 MHz P LO = -3 dBm IP3 - 0 - dBm LO/RF isolation f = 1800 MHz IsoLO/RF -8- d B Not used ports were terminated by 50 Ω .

Siemens Aktiengesellschaft pg. 5/9 16.12.96 HL EH PD21 900MHz measurement and application circuit (Figure 1) printed inductor 1nF2) LO in 1nF IF out Udc=3V3) 100pF 470nH 680Ohms RF in 33pF 47pF 45MHz4.7pF 27nH 920MHz 965MHz 1) Siemens SIMID 01-coil; Ordering code: B82412-A3270-M 2) Optional resistor increases IF-amplifier operating current and improves conversion gain and intermodulation performance (minimum value: 27Ω ) 3) Siemens SIMID 01-coil; Ordering code: B82412-A3471-K

Siemens Aktiengesellschaft pg. 6/9 16.12.96 HL EH PD21 1450MHz measurement and application circuit (Figure 2) printed inductor 1nF2) LO in 1nF IF out Udc=3V 100pF 680Ohms RF in 1450MHz 1350MHz 3.3nH printed inductor 220nH 3.3pF 100MHz 15pF1 8 pF 1) Tune for optimum match 2) Optional resistor increases IF-amplifier operating current and improves conversion gain and intermodulation performance (minimum value: 27Ω ) 3) Siemens SIMID 01-coil; Ordering code: B82412-A3221-K

Siemens Aktiengesellschaft pg. 7/9 16.12.96 HL EH PD21 1900MHz measurement and application circuit (Figure 1) printed inductor 1nF2) LO in 1nF IF out Udc=3V 100pF 680Ohms RF in printed inductor 220nH 100MHz 15pF 18pF 1900MHz 2.2pF 1800MHz 1) Tune for optimum match 2) Optional resistor increases IF-amplifier operating current and improves conversion gain and intermodulation performance (minimum value: 27Ω ) 3) Siemens SIMID 01-coil; Ordering code: B82412-A3221-M

Siemens Aktiengesellschaft pg. 8/9 16.12.96 HL EH PD21 PCB - Layouts for Application Circuits 900MHz - application board: LO IF RF CMY91 4.7pF 1nF 100pF 470nH 47pF 33pF LO IF RF CMY91 Actual size 20mm × 20mm 1450MHz - application board: LO IF RF CMY91 3.3pF 220nH 1nF15pF 18pF 100pF soldered shorting line for tuning the LO-match LO IF RF CMY91 Actual size 20mm × 20mm PCB - data: Glass fiber epoxy board (double sided) εr= 4.8 thickness = 1mm

Siemens Aktiengesellschaft pg. 9/9 16.12.96 HL EH PD21 1900MHz - application board: soldered shorting line for tuning the LO-match LO IF RF CMY91 2.2pF 220nH 1nF 18pF 15pF 100pF LO IF RF CMY91 Actual size 20mm × 20mm PCB - data: Glass fiber epoxy board (double sided) εr = 4.8 thickness = 1mm