CCB200_15 XPPOWER | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 5
Technical content
Input Voltage • See derating curve Input Frequency • 47-63 Hz Input C urrent • 1.8/2.4 A typical at 115 VAC, full load (CCB200/250) 0.9/1.2 A typical at 230 VAC, full load (CCB200/250) Inrush C urrent • 30 Atypicalat230 VAC, cold start at 25 °C Pow er Factor • >0.9 Earth Leakage C urrent • 250 µA max at 264 VAC/60 Hz N o Load Input Pow er • <0.5 W when inhibit used (CCB200) Patient Leakage C urrent • 100 µA max, 264 VAC 60 Hz Input Protection • Internal T5.0 A/250 V fuse in line and neutral Output O utput Voltage • 12-48 VDC (see tables) O utput Voltage Trim • ±3% CCB250, ±5% CCB200 (See Mechanical Details) Initial Set Accuracy • ±0.5% V1, ±5% V2 M inim um Load • No minimum load required Start U p D elay • 1 s typical Start U p R ise Tim e • 0.5 s typical H old U p Tim e • 16/20 ms min at 90 VAC (CCB250/200) D rift • ±0.2% after 20 min warm up Line R egulation • ±0.5% max Load R egulation • ±1% V1, ±5% V2 O ver/U ndershoot • 5% max Transient R esponse • 4% max. deviation, recovery to within 1% in 500 µs for a 50-75-50% load change R ipple & N oise • 1% pk-pk, 20 MHz bandwidth O vervoltage Protection • 115-140% Vnom, recycle input to reset (V1 only) O verload Protection • 125-165% Inom V1 (CCB250), 110 - 150% Inom V1 (CCB200) Short C ircuit Protection • Continuous trip and restart (hiccup mode) Tem perature • 0.05% /°C C oefficient R em ote O n/O ff • Uncommitted isolated optocoupler diode, (Inhibit/Enable) powered diode inhibits V1 xppow er.com General Efficiency • Up to 95% Isolation • 4000 VAC Input to Output 2 x MOPP,
1500 VAC Input to Ground 1 x MOPP,
1500 VAC Output to Ground 1 x MOPP
Sw itching Frequency • See longform datasheet Signals • Power Fail Inhibit, 5 V Standby M TB F • 369/230 kHrs to MIL-HDBK-217F at 25 °C, GB (CCB250/200) Environmental O perating Tem perature • See derating curve & longform datasheet C ooling • Convection cooled O perating H um idity • 95% RH, non-condensing Storage Tem perature • -40 °C to +85 °C O perating Altitude • 3048 m for CCB250, 5000 m for CCB200 Shock • ±3 x 30g shocks in each plane, total 18 shocks. 30g = 11ms (±0.5 ms), half sine, conforms to EN60068-2-27 & EN60068-2-47 Vibration • Single axis 10 - 500 Hz at 2g sweep and endurance at resonance in all 3 planes. Conforms to EN60068-2-6 EMC & Safety Low Voltage PSU EM C • EN61204-3, high severity level Em issions • EN55011/22 level B conducted EN55011/22 level A radiated, See longform datasheet for level A H arm onic C urrents • EN61000-3-2, class A, >140w class C Voltage Flicker • EN61000-3-3 R adiated Im m unity • EN61000-4-3, level 3 Perf Criteria A EFT/B urst • EN61000-4-4, level 3 Perf Criteria A Surge • EN61000-4-5, installation class 3 Perf Criteria A C onducted Im m unity • EN61000-4-6, level 3 Perf Criteria A D ips & Interruptions • EN61000-4-11 , 30% 10 ms, 60% 100 ms, 100% 5000 ms, Perf Criteria A, B, B , EN60601-1-2, 30% 500 ms, 60% 100 ms, 100% 10 ms, 100% 5000 ms, Perf Criteria A, A, A, B - 230 VAC. Consult longform datasheet for 115 V operation. Safety Approvals • IEC60950-1 CB report, UL60950-1, TUV EN60950-1, IEC60601-1 CB report, UL60601-1, TUV 60601-1, Equipm ent Protection • EN60601-1, ANSI/AAMI ES60601-1, C lass CSA22.2 No.60601-1 per cUL BF Rated, Including Risk Management, EN60950, UL60950
- 2 00 & 2 50 W C onvection C ooled
- Very Low H eat Loss
- +70 °C Full Pow er O peration (C C B2 00)
- Very H igh Efficiency up to 95%
- 5 V Standby, Inhibit & Pow er Fail Signals
- IT & M edical (BF) Safety Approvals
- 3 Year W arranty
O utput C onnector C O N 3 1 +V1
2 V1 RTN
1 Line
2 Neutral
09-50-1031 and Molex series 5194 crimp terminals. O utput Pow er O utput Voltage V1 M ax O utput C urrent V1 5 V Standby (O ptional) M odel N um ber 200 W 12.0 V 16.7 A 5 V/0.5 A CCB200PS12 200 W 15.0 V 13.3 A 5 V/0.5 A CCB200PS15 200 W 24.0 V 8.3 A 5 V/0.5 A CCB200PS24 200 W 28.0 V 7.1 A 5 V/0.5 A CCB200PS28 200 W 48.0 V 4.2 A 5 V/0.5 A CCB200PS48 200 W 56.0 V 3.6 A 5 V/0.5 A CCB200PS56 0.22 C64 C53 (5.71) 4.55 (115.57) 0.22 (5.71) 2.55 (64.77) 0.92 (23.48) 1 A +VE -VE 0.30 (7.50) 1.49(37.91) ø0.14 (3.5) thru in 4 positions Output Terminals M4 Screws in 2 positions. Torque to 8lbs-in (90 cNm) max. Output Voltage Control 0.80 (20.2) Mounting holes married with must be connected to safety earth. Pin 2 Pin 1 Pin 10 Pin 9 Detail A Signals Connector CON4 10 way JST B10B-PHDSS 1.43 ±0.04 (36.32 ±1.0) S 0.13 (3.5) A A ø0.14 (3.5) thru in 4 positions 3.00 ±0.02 (76.2 ±0.51) 2.55 (64.7) 0.22 (5.71) 0.92 (23.4) 0.22 (5.71) 1.43 ±0.04 (36.32 ±1.0) 0.13 (3.5) 4.55 (115.5) M Pin 4 Pin 3 Pin 2 Pin 1 Detail B Standby Board O/P Connector Cons JST S48-PH-K-S B 1.49 37.8) 0.80 (20.2) 0.30 (7.5) Output Voltage Control +VE -VE Output Terminals M4 Screws in 2 positions. Torque to 8lbs-in (90 cNm) max. C53 under standby board Standby Board (Option -A) C64 Signals C onnector C O N 4
1 Power Fail (Emitter)
2 Power Fail (Collector)
3 Inhibit (Cathode)
4 Inhibit (Anode)
5 N/C
6 N/C
- For covered version add suffix -C to m odel num ber e.g. C C B 200PS12-C 2. Add suffix -A for 5 V standby option, or -AC for standby and cover options combined. Notes 1. All dimensions in inches (mm). 3. Weight: 0.88 lb (400 g) approx Standby O utput (O ption -A) 1 +5 V 2 +5 V 3 0 V 4 0 V Mates with JST PHDR-10VS housing and JST SPHD-001T- P0.5 crimp terminals Mates with JST PHDR-4 housing and JST SPH-002T-P0.5L crimp terminals
- All dimensions in inches (mm). 3. Weight: 1.36 lb (618 g) approx CCB200PSxx-C Models CCB200PSxx-AC Models Mechanical Details CCB200 M3 Mounting Holes in 2 positions 4.72 (120.0)0.39 (9.85) 0.93 (23.7) Pin 2 Pin 1 Pin 10 Pin 9 Detail A Signals Connector CON4 10 way JST B10B-PHDSS 3.48 ±0.02 (88.5 ±0.5) A -VE +VE 1.75 (44.4) 1.73 (43.9) 1.03 (26.1) 0.59 (15.0) Con 4 Con 3 Con 2 Output Terminals M4 Screws in 2 positions torque to 8 lbs (90 cNm) max. 4.72 (120.0)0.39 (9.85) 1.97 (50.0) 0.7 (19.3) M3 mounting holes in 4 positions maximum penetration by screw to be 3.0 mm from bottom face of cover Output Voltage Control Con 1 M3 Mounting Holes in 2 positions 4.72 (120.0)0.39 (9.85) 0.93 (23.7) Pin 2 Pin 1 Pin 10 Pin 9 Detail A Signals Connector CON4 10 way JST B10B-PHDSS 3.48 ±0.02 (88.5 ±0.5) A -VE +VE 1.75 (44.4) 1.73 (43.9) 1.03 (26.1) 0.59 (15.0) Con 4 Con 3 Con 2 Output Terminals M4 Screws in 2 positions torque to 8 lbs (90 cNm) max. 4.72 (120.0)0.39 (9.85) 1.97 (50.0) 0.7 (19.3) M3 mounting holes in 4 positions maximum penetration by screw to be 3.0 mm from bottom face of cover Output Voltage Control Con 1 B Standby O utput (O ption -A) 1 +5 V 2 +5 V 3 0 V 4 0 V O utput C onnector C O N 3 1 +V1
series 5194 crimp terminals. Signals C onnector C O N 4 SPHD-001T-P0.5 crimp terminals Mates with JST PHDR-4 housing and JST SPH-002T-P0.5L crimp terminals
O utput C onnector C O N 3 1 +V1
3 Earth
09-50-1051 and Molex series 5194 crimp terminals. 1. Peak duration is 500m s m ax, average pow er m ust not exceed 250 W . Notes 1. All dimensions in inches (mm). 3. Weight 1.7 lb (780 g) approx O utput Pow er O utput Voltage V1 O utput C urrent V1 Standby Supply V2 M odel N um ber N om inal Peak (1 ) N om inal Peak (1 ) 0.24 (6.1) 1.98 (50.4) 2.60 (66.3) Output Voltage Adjustment CON 3 -VE +VE Output Terminals M4 Screws in 2 positions torque to 8 lbs-in (90 cNm) max *Signal Connector CON 1 10-way JST-BI0B-PHDSS Mating Half - p/n JST PHDR-10VS, Contact- 26-22 AWG p/n JST SPHD-001T-P0.5 Pin 10 Pin 2 Pin 9 Pin 1 38.1 (1.5) 5.73 (145.42) 0.14 (3.5) 3.73 (94.6) 0.74 (19.0) ø 3.5 through 4 places 6.00 (152.4) C12 C21 Output connectors allow connections from either top or side Signal Connector* 101.6 (4.0) 0.14 (3.5) L N E CON 4 Mounting holes married with must be connected to safety earth. Signals C onnector C O N 1 1 5 V Standby Return 2 5 V Standby 3 5 V Standby Return 4 5 V Standby 5 5 V Standby Return 6 5 V Standby
7 Power Fail (Collector)
8 Power Fail (Emitter)
9 Remote On / Off(Cathode)
10 Remote On / Off(Anode)
Power Fail Inhibit (High) Inhibit (Low) 200 150 100 250 80 85 275 Input Voltage (VAC) Peak Power Availability Output Power (W) 300 90 264 200 150 100 250 -20 -10 0 50 Ambient Temperature (°C) Output Power (W) 300 10 40 60 70 Peak Power Availability Pin 7 CON 1 Power Fail Collector Power Fail Emitter Pin 8 CON 1 POWER SUPPLY Transistor On (<0.8 V): Input & Output Not OK Transistor Off (>4.5 V): Input & Output OK 2K2
5 V Standby Rtn
Pin 1, 3 & 5 CON 1 Pin 2, 4 & 6 CON 1
5 V Standby
Signals N otes & C onditions Power Fail Uncommitted opto isolated transistor, normally off when AC is good Provides ≥ 5 ms (typically 20-30 ms) warning of loss of output from AC failure Remote On/Off (Inhibit/Enable) Uncommitted isolated optocoupler diode, powered diode inhibits the supply Standby Supply V2 Isolated 5 V/0.5 A supply, always present when AC supplied. Inhibit Hi Pin 10 CON 1 POWER SUPPLY Signal Connector Inhibit Lo Pin 9 CON 1 2, 4 & 6 CON 1 Logic GND Pin 1, 3 & 5 CON 1 5 mA 8 V Max
8 V Max
Pin 2, 4 & 6 CON 1 Logic GND Pin 1, 3 & 5 CON 1 5 mA CON 1 1 0 D ec 1 5 Input Voltage & Temperature Derating - CCB250 CCB Mechanical Details Power Fail Inhibit (High) Inhibit (Low) Pin 2 CON 4 Power Fail Collector Power Fail Emitter Pin 1 CON 4 POWER SUPPLY Transistor On: Input & Output Not OK Transistor Off: Input & Output OK Signal Connector 8V Max 3 mA Inhibit Hi Pin 4 CON 4 POWER SUPPLY Signal Connector Inhibit Lo Pin 3 CON 4 5 mA 8 V Max 5 V VI RTN Pin 7 CON 4 P CON 4 5 V VI RTN Pin 7 CON 4 Signals N otes & C onditions Power Fail Uncomitted opto isolated transistor, normally off when AC is good (see fig.5) Provides 5 - 15m s warning of loss of output from AC failure Remote On/Off (Inhibit/Enable) Uncommited isolated optocoupler diode, powered diode inhibits the supply (see fig.6 & 7) 5 V Standby (Optional -A) 5 V/0.5 A Supply, always present when AC applied Input Voltage & Temperature Derating - CCB200 180 160 120 140 200 80 85 Input Voltage (VAC) Output Power (W) 220 90 264 300
5 Seconds Maximum
-20 -10 0 +85 +50 100 200 Ambient Temperature (º C) Output Power (Watts) 182 160 +70 Open Frame Convection Covered Convection (-C) Standby Covered Convection (-AC) 150