C4D15120A CREE | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 5

Technical content

Features

  • 1.2kV Schottky Rectifier
  • Zero Reverse Recovery Current
  • High-Frequency Operation
  • Temperature-Independent Switching
  • Extremely Fast Swtitching Benefits
  • Replace Bipolar with Unipolar Rectifiers
  • Essentially No Switching Losses
  • Higher Efficiency
  • Reduction of Heat Sink Requirements
  • Parallel Devices Without Thermal Runaway

Applications

  • Switch Mode Power Supplies
  • Power Factor Correction
  • Motor Drives Package TO-220-2 Maximum Ratings (TC=25°C unless otherwise specified) Symbol Parameter Value Unit Test Conditions Note VRRM Repetitive Peak Reverse Voltage 1200 V VRSM Surge Peak Reverse Voltage 1300 V VR DC Peak Reverse Voltage 1200 V IF Continuous Forward Current 15

20 A TC<150˚C, no AC component

TC<135˚C, no AC component IFRM Repetitive Peak Forward Surge Current 68

44 A TC=25˚C, tP=10 ms, Half Sine Pulse

TC=110˚C, tP=10 ms, Half Sine Pulse IFSM Non-Repetitive Forward Surge Current 100

85 A TC=25˚C, tP=10 ms, Half Sine Pulse

TC=110˚C, tP=10 ms, Half Sine Pulse Ptot Power Dissipation 192

83 W TC=25˚C

TC=110˚C Tc Maximum Case Temperature 135 ˚C TJ Operating Junction Range -55 to +175 ˚C Tstg Storage Temperature Range -55 to +135 ˚C TO-220 Mounting Torque 1 8.8 Nm lbf-in M3 Screw 6-32 Screw Part Number Package Marking C4D15120A TO-220-2 C4D15120 PIN 1 PIN 2 CASE

C4D15120A Rev. A 0 0.5 1 1.5 2 2.5 3 3.5 4

Electrical Characteristics

Symbol Parameter Typ. Max. Unit Test Conditions Note VF Forward Voltage 1.6 2.3 1.8

3 V IF = 15 A TJ=25°C

IF = 15 A TJ=175°C IR Reverse Current 35 120 200 300 μA VR = 1200 V TJ=25°C VR = 1200 V TJ=175°C QC Total Capacitive Charge 96 nC VR = 1200 V, IF = 15A di/dt = 200 A/μs TJ = 25°C C Total Capacitance 1200 pF VR = 0 V, TJ = 25°C, f = 1 MHz VR = 400 V, TJ = 25˚C, f = 1 MHz VR = 800 V, TJ = 25˚C, f = 1 MHz 1. Note:This is a majority carrier diode, so there is no reverse recovery charge. Thermal Characteristics Symbol Parameter Typ. Max. Unit Test Conditions Note RθJC Thermal Resistance from Junction to Case 0.78 °C/W Typical Performance Figure 1. Forward Characteristics Figure 2. Reverse Characteristics

Figure 7. Transient Thermal Impedance

C4D15120A Rev. A This product has not been designed or tested for use in, and is not intended for use in, applications implanted into the human body nor in applications in which failure of the product could lead to death, personal injury or property damage, including but not limited to equipment used in the operation of nuclear facilities, life-support machines, cardiac defibrillators or similar emergency medical equipment, aircraft navigation or communication or control systems, air traffic control systems, or weapons systems. Copyright © 2006-2011 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree, the Cree logo, and Zero Recovery are registered trademarks of Cree, Inc. Cree, Inc.

4600 Silicon Drive

Durham, NC 27703 USA Tel: +1.919.313.5300 Fax: +1.919.313.5451 www.cree.com/power Recommended Solder Pad Layout Part Number Package Marking C4D15120A TO-220-2 C4D15120 TO-220-2 A C E D G H B J L M N F P Q S T U V W X Y M i n M a x M i n M a x A . 3 9 5 . 4 1 0 1 0 . 0 3 3 1 0 . 4 1 4 B . 2 3 5 . 2 5 5 5 . 9 6 9 6 . 4 7 7 C . 1 0 2 . 1 1 2 2 . 5 9 1 2 . 8 4 5 D . 3 3 7 . 3 3 7 8 . 5 6 0 8 . 5 6 0 E . 5 9 0 . 6 1 0 1 4 . 9 8 6 1 5 . 4 9 4 F . 1 4 9 . 1 5 3 3 . 7 8 5 3 . 8 8 6 G 1 . 1 2 7 1 . 1 4 7 2 8 . 6 2 6 2 9 . 1 3 4 H . 5 3 0 . 5 5 0 1 3 . 4 6 2 1 3 . 9 7 0 J L . 0 2 8 . 0 3 6 . 7 1 1 . 9 1 4 M . 0 4 5 . 0 5 5 1 . 1 4 3 1 . 3 9 7 N . 1 9 5 . 2 0 5 4 . 9 5 3 5 . 2 0 7 P . 1 7 0 . 1 8 0 4 . 3 1 8 4 . 5 7 2 Q . 0 4 8 . 0 5 4 1 . 2 1 9 1 . 3 7 1 S 3 ° 5 ° 3 ° 5 ° T 3 ° 5 ° 3 ° 5 ° U 3 ° 5 ° 3 ° 5 ° V . 1 0 0 . 1 1 0 2 . 5 4 2 . 7 9 4 W . 0 1 4 . 0 2 1 . 3 5 6 . 5 3 3 X 3 ° 5 ° 3 ° 5 ° Y . 3 9 5 . 4 1 0 1 0 . 0 3 3 1 0 . 4 1 4 Z . 1 3 0 . 1 5 0 3 . 3 0 2 3 . 8 1 0 I n c h e s M i l l i m e t e r sP O S R 0 . 0 1 0 R 0 . 2 5 4 1 2 Z Package Dimensions Package TO-220-2 POS Inches Millimeters Min Max Min Max A .381 .410 9.677 10.414 B .235 .255 5.969 6.477 C .100 .120 2.540 3.048 D .223 .337 5.664 8.560 E .590 .615 14.986 15.621 F .143 .153 3.632 3.886 G 1.105 1.147 28.067 29.134 H .500 .550 12.700 13.970 J R 0.197 R 0.197 L .025 .036 .635 .914 M .045 .055 1.143 1.397 N .195 .205 4.953 5.207 P .165 .185 4.191 4.699 Q .048 .054 1.219 1.372 S 3° 6° 3° 6° T 3° 6° 3° 6° U 3° 6° 3° 6° V .094 .110 2.388 2.794 W .014 .025 .356 .635 X 3° 5.5° 3° 5.5° Y .385 .410 9.779 10.414 z .130 .150 3.302 3.810 NOTE: 1. Dimension L, M, W apply for Solder Dip Finish PIN 1 PIN 2 CASE