BSP350 INFINEON | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 6
Technical content
Mini PROFET ® BSP 350 Semiconductor Group Page 1 of 6 08.04.97 MiniPROFET
- High-side switch
- Short-circuit protection
- Overtemperature protection with hysteresis
- Overload protection
- Overvoltage protection
- Reverse battery protection
- Switching inductive load
- Clamp of negative output voltage with inductive loads
- Maximum current internally limited Package: SOT 223 Type Ordering code BSP 350 Q67000-S227 Maximum Ratings Parameter Symbol Values Unit Supply voltage Vbb 50 V Load current self-limited IL IL(SC ) A Maximum current through input pin (DC) see internal circuit diagram IIN ±15 mA Inductive load switch-off energy dissipation EAS 5m J Operating temperature range Storage temperature range Tj Tstg -40 ...+150 -55 ...+150 Max. power dissipation (DC)2) TA = 25 °C Ptot 1.7 W Thermal resistance chip - soldering point: chip - ambient: R thJS R thJA K/W + Vbb GND Control Circuit R Temperature Sensor OUT IN R L IN 1) For 12 V applications only. Reverse load current only limited by connected load. 2) BSP 350 on epoxy pcb 40 mm x 40 mm x 1.5 mm with 6 cm2 copper area for Vbb connection Pins: 12 3 4 IN V bb OUT V bb
Semiconductor Group Page 2 08.04.97
Electrical Characteristics
Parameter and Conditions Symbol Values Unit at Tj = 25 °C, Vbb = 13.5V unless otherwise specified min typ max Load Switching Capabilities and Characteristics On-state resistance (pin 2 to 3) IL = 0.07 A, pin 1 = GND Tj = 25°C Tj = 150°C Vbb = 6 V, Tj = 25°C R ON -- Ω Nominal load current (pin 2 to 3) ISO Standard: VON = Vbb - VOUT = 0.5 V TS = 85 °C IL(ISO) 0.07 -- -- A Turn-on time to 90% VOUT Turn-off time to 10% VOUT RL = 270 Ω ton toff 100 140 µs Slew rate on 10 to 30% VOUT , R L = 270 Ω dV /dton -- 4 6 V/ µs Slew rate off 70 to 40% VOUT , R L = 270 Ω -dV/dtoff -- 2 6 Input OFF state input current Tj = - 40...+150°C R L = 270 Ω, VOUT ≤ 0,1V IIN(off) -- -- 0.05 mA ON state input current, (pin 1 grounded) Tj = - 40...+150°C IIN(on) -- 0.3 1 mA Operating Parameters Operating voltage (pin 1 grounded) Tj = - 40...+150°C Vbb(on) 4.9 -- 45 V Leakage current (pin 2 to 3, pin 1 open)Tj = 25°C Tj =150°C Ibb(off) -- 1.2 µA 3) Driver circuit must be capable to drive currents >1mA. 4) Below Vbb=4.5 V typ. without chargepump, Vout ≈ Vbb - 2 V
Semiconductor Group Page 3 08.04.97 Parameter and Conditions Symbol Values Unit at Tj = 25 °C, Vbb = 13.5V unless otherwise specified min typ max Protection Functions Current limit (pin 2 to 3) 5) Tj = 25°C Tj = -40...+150° IL(SC) 0.2 0.1 0.5 1.2 A Thermal overload trip temperature Tjt 150 -- -- °C Thermal hysteresis ΔTjt -- 20 -- K Overvoltage protection Tj =-40...+150°CVbbin(AZ) 50 56 -- V Output clamp (ind. load switch off) at VOUT = Vbb - VON(CL) VON(CL) -- 56 -- V Inductive load switch-off energy dissipation 6) EAS -- -- 5m J Reverse battery resistor (pin 1 to 2) R IN -- 1 -- k Ω Reverse Diode Continious reverse drain current Tj = 25°C IS -- -- 0.2 A Pulsed reverse drain current Tj = 25°C ISM -- -- 0.8 A Diode forward on voltage IF = 0.2 A, IIN = ≤ 0.05 mA VSD -- 0.9 1.2 V 5) load current limits onset at IL * Ron approx. 1V short circuit protection: combination of current limit and thermal overload switch off 6) while demagnetizing load inductance, dissipated energy is EAS = ∫(VON(CL) * iL(t) dt, approx. EAS = 1/2 * L * I2 L * ( VON(CL) VON(CL)-Vbb
Semiconductor Group Page 4 08.04.97 Max allowable power dissipation Ptot = f (TA ,TSP ) Ptot [W] 0 25 50 75 100 125 150 T A SP T TA, TSP [°C] On state resistance (Vbb- pin to OUT pin) R ON = f (Tj);Vbb = 13.5 V;IL = 70 mA R ON [Ω ] -50 -25 0 25 50 75 100 125 150 typ 98% TJ [°C] Typ. on state resistance (Vbb- pin to OUT pin) R ON = f (Vbb); IL = 70 mA; Tj = 25°C R ON [Ω ] 0 5 10 15 20 25 Vbb [V] Typ. short circuit current IL(SC) = f(Tj); Vbb = 13.5V ILSC [Α ] 0.1 0.2 0.3 0.4 0.5 0.6 0.7 -50 -25 0 25 50 75 100 125 150 TJ [°C]
Semiconductor Group Page 5 08.04.97 Typ. short circuit current IL(SC) = f(VON ); Vbb = 13.5V; Tj = 25°C ILSC [Α ] 0.1 0.2 0.3 0.4 0.5 0.6 0.7 02468 VON [V] Typ. short circuit current IL(SC) = f(t); Vbb = 13.5V no heatsink; Parameter: TjStart IL(SC)[mA] 200 400 600 800 1000 -40°C 25°C125°C t[s] Test circuit V Vin Vbb Iin out Von Turn on conditions Chargepump threshold VON = f (Vbb) typ. max. 2 4 6 8
Semiconductor Group Page 6 08.04.97 Package: all dimensions in mm. SOT 223/3: Edition 7.97 Published by Siemens AG, Bereich Halbleiter Vetrieb, Werbung, Balanstraße 73,
81541 München
© Siemens AG 1997 All Rights Reserved. Attention please! As far as patents or other rights of third parties are concerned, liability is only assumed for components, not for applications, processes and circuits implemented within components or assemblies. The information describes a type of component and shall not be considered as warranted characteristics. Terms of delivery and rights to change design reserved. For questions on technology, delivery and prices please contact the Semiconductor Group Offices in Germany or the Siemens Companies and Representatives worldwide (see address list). Due to technical requirements components may contain dangerous substances. For information on the types in question please contact your nearest Siemens Office, Semiconductor Group. Siemens AG is an approved CECC manufacturer. Packing Please use the recycling operators known to you. We can also help you - get in touch with your nearest sales office. By agreement we will take packing material back, if it is sorted. You must bear the costs of transport. For packing material that is returned to us unsorted or which we are not obliged to accept, we shall have to invoice you for any costs incurred. Components used in life-support devices or systems must be expressly authorized for such purpose! Critical components 1 of the Semiconductor Group of Siemens AG, may only be used in life-support devices or systems2 with the express written approval of the Semiconductor Group of Siemens AG. 1) A critical component is a component used in a life-support device or system whose failure can reasonably be expected to cause the failure of that life-support device or system, or to affect its safety or effectiveness of that device or system. 2) Life support devices or systems are intended (a) to be implanted in the human body, or (b) to support and/or maintain and sustain and/or protecf human life. If they fail, it is reasonable to assume that the health of the user or other persons may be endangered.