BSOV3S3 CONNOR-WINFIELD | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 2

Technical content

THE CONNOR-WINFIELD CORP. 2111 COMPREHENSIVE DRIVE. AURORA, IL 60505. FAX (630) 851-5040. PHONE (630) 851-4722. P R O D U C T D A T A S H E E T Specifications subject to change without notice. DATA SHEET #: REV: DATE: PAGE OF Copyright 2001 Connor-Winfield all rights reserved. a CRYSTAL CONTROLLED OSCILLATORS The Connor-Winfield BSOV3S3 is a true Surface Mount 3.3V, Voltage Controlled Oven Controlled Crystal Oscillator (VCOCXO) with an HCMOS output. The BSOV3S3 is designed for Stratum 3 applications requiring high pullability, tight frequency stability and low jitter. BSOV3S3 - 12.80MHz OCXO SERIES CENTER FREQUENCY

FEATURES

DESCRIPTION

ORDERING INFORMATION

3.3V OPERATION LOW JITTER <1pS RMS TEMPERATURE STABILITY ±0.25ppm FREQUENCY TOLERANCE OF ±4.6ppm OVER TEN YEARS SURFACE MOUNT PACKAGE TAPE AND REEL PACKAGING SURFACE MOUNT 3.3V HCMOS STRATUM 3 OCXO BSOV3S3 Cx032 11/12/04 www.conwin.com CW 0107 BSOV3S3 12.80M Notes: 1) Initial calibration @ 25°C, Vc=1.59 Vdc. 2) Frequency vs. temperature stability 3) At the time of shipment after48 hours of operation. 4) Inclusive of calibration, operating temperature range, supply voltage change, load change, shock and vibration, 20 years aging. 5) Measured @ 25°C, within 5 minutes, the unit will be within +/-0.1ppm of its reference frequency, measured after 30 minutes of continuous operation at a stable 25°C 6) Referenced to Fo @ 25°C, Positive Transfer Characteristic ABSOLUTE MAXIMUM RATINGS TABLE 1.0 PARAMETER UNITS MINIMUM NOMINAL MAXIMUM UNITS NOTE Storage Temperature -40 Supply Voltage (Vcc) -0.5 4.5 Vdc Control Voltage (Vc) -0.5 4.5 Vdc OPERATING SPECIFICATIONS TABLE 2.0 PARAMETER MINIMUM NOMINAL MAXIMUM UNITS NOTE Center Frequency (Fo) 1.544 20.0 MHz Frequency Calibration, Vc=1.59 Vdc -1.5 1.5 ppm Frequency Stability -0.25 0.25 ppm Aging (Daily) -30 ppb Aging (20 Years) -2.5 2.5 ppm Total Frequency Tolerance -4.6 4.6 ppm Operating Temperature Range Supply Voltage (Vcc) 3.135 3.3 3.465 Vdc Supply Current (Icc) 450 mA Phase Jitter (BW=12KHz to 20MHz) ps rms Phase Jitter (BW=10Hz to 20MHz) ps rms Period Jitter ps rms SSB Phase Noise at 10Hz offset -90 dBc/Hz SSB Phase Noise at 10KHz offset -135 dBc/Hz Warm Up Time Minutes TDEV @ 1.0 Sec. nS TDEV @ 4.0 Sec. nS INTPUT CHARACTERISTICS TABLE 3.0 PARAMETER MINIMUM NOMINAL MAXIMUM UNITS NOTE Control Voltage Range (Vc) 0.3 1.59 3.0 Vdc Frequency at Vc=0.3 Vdc -38 -25 ppm Frequency at Vc=3.0 Vdc ppm Slope of Frequency Adjust 18.5 ppm/V Input Impedance 100k Ohm HCMOS OUTPUT CHARACTERISTICS TABLE 4.0 PARAMETER MINIMUM NOMINAL MAXIMUM UNITS NOTE LOAD pf Voltage (High) (Voh) 2.6 Vdc (Low) (Vol) 0.4 Vdc Current (High) (Ioh) mA (Low) (Ioh) mA Duty Cycle at 50% of Vcc Rise / Fall Time 10% to 90% nS PACKAGE CHARACTERISTICS TABLE 5.0 Package Surface Mount, Non-hermetic package consisting of an FR4 substrate with grounded metal cover. PROCESS RECOMMENDATIONS TABLE 6.0 Solder Reflow The component solder used internal to this device has a m elting point of 221°C. The peak temperature inside the device should be less than or equal to 220°C for a maximum of 10 seconds Wash Ultrasonic cleaning is not recommended

THE CONNOR-WINFIELD CORP. 2111 COMPREHENSIVE DRIVE. AURORA, IL 60505. FAX (630) 851-5040. PHONE (630) 851-4722. P R O D U C T D A T A S H E E T Specifications subject to change without notice. DATA SHEET #: REV: DATE: PAGE OF Copyright 2001 Connor-Winfield all rights reserved. a CRYSTAL CONTROLLED OSCILLATORS Cx032 11/12/04 www.conwin.com PIN FUNCTION

1 CONTROL VOLTAGE

7 GROUND (CASE)

8 OUTPUT

14 Vcc

90% 50% 10% CW DATE CODE BSOV3S3 12.80M CW DATE CODE BSOV3S3 12.80M .330 max (8.382mm) .330 max (8.382mm) 3.0Vdc 3.3Vdc CONTROL VOLTAGE POWER SUPPLY ENVIRONMENTAL CHARACTERISTICS Temperature Cycle: Per MIL-STD-883, Method 1010, Condition B. -55°C to 125°C, 20 cycles,10 minute dwell, 1minute transition. SOLDERING Pad Solderability: Per MIL-STD-883, Method 2003. 8 hour steam age prior to 245°C ±5°C Solder pot dip, 95% Coverage. Solder Reflow: The component solder internal to this device has a melting point of 221°C, the peak temperature inside the device should be less than or equal to 220°C for a maximum of 10 seconds. MECHANICAL CHARACTERISTICS Vibration: Per MIL-STD-202, Method 204, Condition A. 10G’s peak, 10Hz to 500Hz, 15minute cycles 12 times each perpendicular axis. Shock: Per MIL-STD-202, Method 213, Condition D. 500G’s, 1ms, halfsine, 3 shocks per direction. Moisture Resistance: Per MIL-STD-202, Method 106. 95% RH @ 65°C, 10 cycles 10°C to 65°C. Dimensional Tolerance: ±.005 (.127mm) KEEP OUT AREA .830 (21.08mm) .565 (14.35mm)