Power Management

BA03CC0FP-E2

Rohm

Low-saturation regulators, available for output s up to 2A/1A.

Manufacturer: Rohm

Document: 23 Pages / 493Kb

Request Quote Download Datasheet Read online HTML view

Read BA03CC0FP-E2 online.

BAXXDD0-E ROHM | Alldatasheet

Document overview

Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
PDF pages: 23

Technical content

○Product structure : Silicon monolithic integrated circuit ○This product is not designed protection against radioactive rays. 1/20 TSZ02201-0R6R0A600130-1-2© 2012 ROHM Co., Ltd. All rights reserved. TSZ22111･14･001 26.Jun.2012 Rev.001 www.rohm.com Datasheet 2A/1A Fixed Output LDO Regulators BAxxDD0T Series BAxxCC0T Series BAxxCC0FP Series 2A/1A Fixed Output LDO Regulators With Shutdown Swicth BAxxDD0WT Series BAxxDD0HFP Series BAxxCC0WT Series BAxxCC0WFP Series

General Description Standard Fixed Output LDO Regulators are low-saturation regul ators, available for output s up to 2A / 1A. ROHM has a wide output voltage range and package lineup with and without sh utdown switches. This IC has a built-in over-current protection circuit that prevents the destruction of the IC due to output short circuits, a thermal shut-down circuit that protects the IC from damage due to overloading and an over-voltage protection circuit that protects the IC from surges generated in the power supply line of the IC.
Features ±1% highly accurate output voltage (BAxxDD0xx) Low saturation with PNP output Built-in over-current prot ection circuit that prevents the destruction of the IC due to output short circuits Built-in thermal shutdown circuit for protecting the IC from damage due to overloading Built-in over- voltage protection circuit that prevents the destruction of the IC due to power supply surges
Key Specification Input Power Supply Voltage: 25V (Max.) Output voltage type: Fixed Output current: BAxxDD0xx series 2A (Max.) BAxxCC0xx series 1A (Max.) Shutdown current: 0μA(Typ.) Operating temperature range: -40 ℃ to +125 ℃
Applications Used in DSP power supplies for DVD and CD players, FPDs, televisions, personal computers or any other consumer device
Packages W (Typ.) x D (Typ.) x H (Max.) HRP5 9.395mm x 10.54mm x 2.005mm TO252-3 6.50 mm x 9.50mm x 2.50 mm TO252-5 6.50 mm x 9.50mm x 2.50 mm TO220FP-3 10.00 mm x 30.50mm x 4.60 mm TO220FP-5 10.00 mm x 30.50mm x 4.60 mm
Lineup matrix ■1A output BAxxCC0xx Series Part Number Output voltage (V) Package ■2A output BAxxDD0xx Series Part Number Output voltage (V) Package TO252-5 TO220FP-5 TO220FP-3 HRP5 TO252-3

Ordering Information B A x x x x 0 x x x x - x x Part Number Output voltage Output Current CC0 : 1A DD0 : 2A Shutdown Switch W : Includes switch None: without switch Package Packaging and forming specification TR: Embossed tape and reel ( H R P 5 ) E2: Embossed tape and reel (TO252-3,TO252-5) None : Container Tube (TO220FP-3,TO220FP-5) HFP FP T : HRP5 : TO252-5 : TO252-3 : TO220FP-5 : TO220FP-3
Lineup ■1A output BAxxCC0xx Series Maximum output current (Max.) Shutdown Switch Package Output voltage(Typ.) Orderable Part Number With Switch TO252-5 Reel of 2000 3.3V BA033CC0WFP-E2 5.0V BA05CC0WFP-E2 6.0V BA06CC0WFP-E2 7.0V BA07CC0WFP-E2 8.0V BA08CC0WFP-E2 9.0V BA09CC0WFP-E2 12.0V BAJ2CC0WFP-E2 TO220FP-5 Tube of 500 3.0V BA03CC0WT 3.3V BA033CC0WT 5.0V BA05CC0WT 7.0V BA07CC0WT 8.0V BA08CC0WT 9.0V BA09CC0WT 10.0V BAJ0CC0WT 12.0V BAJ2CC0WT No switch TO252-3 Reel of 2000 3.0V BA03CC0FP-E2 3.3V BA033CC0FP-E2 5.0V BA05CC0FP-E2 6.0V BA06CC0FP-E2 7.0V BA07CC0FP-E2 8.0V BA08CC0FP-E2 9.0V BA09CC0FP-E2 10.0V BAJ0CC0FP-E2 12.0V BAJ2CC0FP-E2 15.0V BAJ5CC0FP-E2 TO220FP-3 Tube of 500 3.0V BA03CC0T 3.3V BA033CC0T 5.0V BA05CC0T 6.0V BA06CC0T 7.0V BA07CC0T 8.0V BA08CC0T 9.0V BA09CC0T 10.0V BAJ0CC0T 12.0V BAJ2CC0T 15.0V BAJ5CC0T

TSZ02201-0R6R0A600130-1-2© 2012 ROHM Co., Ltd. All rights reserved. TSZ22111･15･001 26.Jun.2012 Rev.001 www.rohm.com ■2A output BAxxDD0xx Series Maximum output current (Max.) Shutdown Switch Package Output voltage(Typ.) Orderable Part Number With Switch TO220FP-5 Tube of 500 1.5V BA15DD0WT 1.8V BA18DD0WT 2.5V BA25DD0WT 3.0V BA30DD0WT 3.3V BA33DD0WT 5.0V BA50DD0WT 9.0V BA90DD0WT 12.0V BAJ2DD0WT 16.0V BAJ6DD0WT HRP5 Reel of 2000 1.5V BA15DD0WHFP-TR 1.8V BA18DD0WHFP-TR 2.5V BA25DD0WHFP-TR 3.0V BA30DD0WHFP-TR 3.3V BA33DD0WHFP-TR 5.0V BA50DD0WHFP-TR 9.0V BA90DD0WHFP-TR 12.0V BAJ2DD0WHFP-TR 16.0V BAJ6DD0WHFP-TR No switch TO220FP-3 Tube of 500 1.5V BA15DD0T 1.8V BA18DD0T 2.5V BA25DD0T 3.0V BA30DD0T 3.3V BA33DD0T 5.0V BA50DD0T 9.0V BA90DD0T 12.0V BAJ2DD0T 16.0V BAJ6DD0T

Block Diagrams / Pin Configurations / Pin Descriptions BAxxCC0WFP/ BAxxDD0WHFP/ BAxxCC0WT/ BAxxDD0WT PIN No. Pin Name Function

1 CTL Output voltage ON/OFF control

2 Vcc Power supply voltage input

3 N.C./GND Unconnected terminal/GND* 1

4 OUT Voltage output

5 N.C. Unconnected terminal Fin GND GND* 2 *1 TO252-5=N.C.,TO220FP-5,HRP5=GND *2 TO252-5,HRP5 only BAxxCC0T/ BAxxCC0FP/ BAxxDD0T PIN No. Pin Name Function

1 Vcc Power supply voltage input

2 N.C./GND Unconnected terminal/GND* 1

3 OUT Voltage output

Fi GND GND* 2 *1 TO252-3=N.C.,TO220FP-3=GND *2 TO252-3 only Fig.1 1 2 3 4 5 Fin Vcc Driver OVP TSD OCP CTL Vcc N.C. (TO252-5) GND (TO220FP-5,HRP5) OUT N.C. Vref GND(TO252-5･HRP5) Fig.2 (TO220FP-3) 1 2 3 Fin Vcc Driver OVP TSD OCP Vcc N.C. OUT (TO252-3) GND Vref GND(TO252-3) HRP5 TOP VIEW FIN TO252-5 1 2 3 4 5 1 2 3 4 5 TO220FP-5 1 2 3 4 5 TO220FP-3 TO252-3 FIN 2 3 1 TOP VIEW

Absolute Maximum Ratings (Ta=25℃) Parameter Symbol Ratings Unit Input Power Supply Voltage*1 V CC -0.3 to +35 V Power Dissipation*2 Pd 2300(HRP5) mW 1300(TO252-5) 1200(TO252-3) 2000(TO220FP-3,5) Operating Temperature Range Topr -40 to +125 ℃ Ambient Storage Temperature Tstg -55 to +150 ℃ Junction Temperature TjMAX. +150 ℃ Output Control Terminal Voltage*3 Vctl -0.3 to +Vcc V Voltage Applied to the Tip *4 VCC peak +50 V *1 Must not exceed Pd *2 HRP5 : In cases in which Ta ≧25℃ when a 70mm ×70mm×1.6mm glass epoxy board is used, the power is reduced by 18.4 mW/℃. TO252FP-3 : In cases in which Ta ≧25℃ when a 70mm ×70mm×1.6mm glass epoxy board is used, the power is reduced by 9.6 mW/ ℃. TO252FP-5 : In cases in which Ta ≧25℃ when a 70mm ×70mm×1.6mm glass epoxy board is used, the power is reduced by 10.4 mW/ ℃. TO220FP-5 : No heat sink. When Ta ≧25℃, the power is reduced by 16 mW/℃. *3 Only for models with shutdown switches. *4 Applied voltage : 200msec or less (tr ≥1msec)
Recommended Operating Ratings (Ta=25℃) Parameter Symbol Ratings Unit Min. Typ. Max. Input Power Supply Voltage BAxxCC0xx VCC 4.0 ― 25.0 V BAxxDD0xx 3.0 ― 25.0 V Output Current BAxxCC0xx Io ― ― 1 A BAxxDD0xx ― ― 2 A Output Control Terminal Voltage Vctl 0 ― V CC V MAX200msec (Voltage Supply more than 35V) 50V 35V tr≧1msec

Electrical Characteristics BAxxCC0 Series (Unless otherwise specified, Ta=25℃, VCTL=5V, Io=500mA Setting *5) Parameter Symbol Limit Unit Conditions Min. Typ. Max. Output Voltage *6 Vo Vo(T)×

0.98 Vo(T) Vo(T)×

1.02 V Shut Down Current Isd － 0 10 μA V CTL=0V Bias Current Ib － 2.5 5.0 mA V CTL=2V, Io=0mA Dropout Voltage ΔVd － 0.3 0.5 V Vcc=Vo×0.95 Peak Output Current Io 1.0 －－ A Ripple Rejection R.R. 45 55 － dB f=120Hz, ein*7=1Vrms, Io=100mA Line Regulation Reg.I － 20 100 mV Vcc=Vo(T)+1→25V Load Regulation Reg.L － 50 150 mV Io=5mA →1A Temperature Coefficient of Output Voltage *8 Tcvo － ±0.02 －％/℃ Io=5mA,Tj=0 to 125℃ Output Short Current Ios － 0.40 － A Vcc=25V ON Mode Voltage VthH 2.0 －－ V ACTIVE MODE, Io=0mA OFF Mode Voltage VthL －－ 0.8 V OFF MODE, Io=0mA Input High Current ICTL 100 200 300 μA V CTL=5V, Io=0mA BAxxDD0 series (Unless otherwise specified, Ta=25℃, VCTL=3V, Vcc=VCCT*9) Parameter Symbol Limit Unit Conditions Min. Typ. Max. Shut Down Current Isd － 0 10 μA V CTL=0V, Io=0mA Bias Current Ib － 0.9 2.0 mA Io=0mA Output Voltage *10 Vo Votyp×

0.99 Votyp Votyp×

1.01 V Io=200mA

Dropout Voltage 1 *11 ΔVd1 － 0.3 0.5 V Vcc=0.95×Vo, Io=1A Dropout Voltage 2 *11 ΔVd2 － 0.45 0.7 V Vcc=0.95 ×Vo, Io=2A Peak Output Current Io 2.0 －－ A Ripple Rejection R.R. － 55 － dB f=120Hz , ein*7=-20dBV, Io=100mA Line Regulation Reg.I － 15 50 mV Vcc=VCCT*9V→25V, Io=200mA Load Regulation Reg.L － 50 200 mV Io=0mA →2A Temperature Coefficient of Output Voltage *8 Tcvo － ±0.02 － %/ ℃ Io=5mA, Tj=0 to 125℃ CTL ON Mode Voltage Von 2.0 － Vcc V ACTIVE MODE, Io=0mA CTL OFF Mode Voltage Voff －－ 0.8 V OFF MODE, Io=0mA CTL Input Current ICTL － 60 120 μA V CTL=3V, Io=0mA *5 Vo=3.3V:Vcc=8.3V, Vo=5V:Vcc=10V, Vo=6V:Vcc=11V, Vo=7V:Vcc=12V, Vo=8V:Vcc=13V, Vo=9V:Vcc=14V, Vo=12V:Vcc=17V *7 ein : Input Voltage Ripple *8 Not 100% tested *11 Vo≧3.0V

Typical Performance Curves (Unless specified otherwise, Vcc=8.3V, Vo=3.3V, VCTL=5.0V, and Io=0mA) BAxxCC0xx (BA33CC0WT) Fig.5 Input Stability (Io=500mA) Fig.6 Load Stability Fig.3 Circuit current Fig.4 Input Stability

Typical Performance Curves - continued Fig.8 Ripple Rejection Characteristics (Io=100mA) Fig.9 Output Voltage Temperature Characteristics Fig.10 Circuit Current by load Level (IOUT=0mA→1A) Fig.7 Input/Output Voltage Difference Io-△Vd Characteristics (Vcc＝2.95V)

Typical Performance Curves - continued Fig.12 CTL Voltage vs. Output Voltage Fig.13 Overvoltage Operating Characteristics (Io=200mA) Fig.14 Thermal Shutdown Circuit Characteristics Fig.11 CTL Voltage vs. CTL Current

Typical Performance Curves - continued (Unless specified otherwise, Vcc=7.0V, Vo=5.0V, VCTL=3.0V, and Io=0mA) BAxxDD0xx (BA50DD0WT) Fig.16 Input Stability (Io=0mA) Fig.17 Input Stability (Io=2A) Fig.15 Circuit Current Fig.18 Load Stability

Typical Performance Curves - continued Fig.20 Ripple Rejection Characteristics Fig.21 Temperature Characteristics Fig.19 Input/Output Voltage Difference Fig.22 Circuit Current by Load Level (lout=0mA→2A)

Typical Performance Curves - continued Fig.25 Overvoltage Operating (lo=200mA) Fig.26 Thermal Shutdown Circuit Characteristics Fig.23 CTL Voltage vs. CTL Current Fig.24 CTL Voltage vs. Output Voltage [V] [BA50DD0WT]

I/O equivalence circuit <BAxxDD0xx Series> <BAxxCC0xx Series> Fig.27 Fig.28
Power Dissipation Vcc CTL 39kΩ 2k Ω 31kΩ 10kΩ Vcc OUT Vcc CTL 25kΩ 25kΩ 10kΩ OUT Vcc Fig.29 Fig.30 Fig.31 0.0 0.4 0.8 1.2 1.6 2.0 0 25 50 75 100 125 150 Ambient temperature:Ta(℃） Power Dissipation:Pd(W) Mounted on a Rohm standard board Board size : 70×70×1.6 ㎜ Copper foil area :7×7 ㎜ TO252-5θja=96.2(℃/W) 1.30 0 25 50 75 100 125 150 Ambient temperature:Ta(℃） Power Dissipation:Pd(W) (1)20.0 (2)2.0 When using a maximum heat sick : θj-c=6.25(℃/W) When using an IC alone : θj-6=62.5(℃/W) 0 25 50 75 100 125 150 Ambient temperature:Ta(℃） Power Dissipation:Pd(W) Board size : 70×70×1.6 ㎜ 3 (board contains a thermal via) Board front copper foil area : 10.5×10.5 ㎜ 2 ①2-layer board (back surface copper foil area :15×15 ㎜ 2) ②2-layer board (back surface copper foil area :70×70 ㎜ 2) ③4-layer board (back surface copper foil area :70×70 ㎜ 2) ③7.3W ②5.5W ①2.3W HRP-5 TO220FP-5 TO252-5

TSZ02201-0R6R0A600130-1-2© 2012 ROHM Co., Ltd. All rights reserved. TSZ22111･15･001 26.Jun.2012 Rev.001 www.rohm.com When using at temperatures over Ta=25 ℃, please refer to the heat reducing characteristics shown in Fig.29 through 31. The IC characteristics are closely related to the temperatur e at which the IC is used and if the temperature exceeds the maximum junction temperature TjMAX., the elements may be damaged or destroyed. From the standpoints of instantaneous destruction and long-term operating reliability, it is necessary gi ve sufficient consideration to IC heat. In order to protect the IC from thermal damage, it is necessary to operate it at temperatures lower than the maximum junction temperature Tj MAX of the IC. Fig.30 shows the acceptable loss and heat reducing charac teristics of the TO220FP package The portion shown by the diagonal line is the acceptable loss range that can be used wi th the IC alone. Even when the ambient temperature Ta is a normal temperature (25℃), the chip (junction) temperature Tj may be quite high so please operate the IC at temperatures less than the acceptable loss Pd. The method of calculating the power consumption Pc (W) is as follows. Pc = (Vcc-Vo) × Io ＋ Vcc × Icca A c c e p t a b l e l o s s P d≦Pc Solving this for load current IO in order to operate within the acceptable loss: Io ≦ (Please refer to Fig.10 and 22 for Icca.) It is then possible to find the maximum load current IoMAX with respect to the applied voltage Vcc at the time of thermal design. ・Calculation Example Example 1) When Ta=85℃, Vcc=8.3V, Vo=3.3V, BA33DD0WT Io≦ With the IC alone : θja=62.5℃/W → -16mW/ ℃ Io≦200mA (Icca : 2mA) 25 ℃=2000mW → 85℃=1040mW Please refer to the above information and keep thermal designs within the scope of acceptable loss for all operating temperature ranges. The power consumption Pc of the IC when there is a short circuit (short between Vo and GND) is: Pc=Vcc×(Icca＋Ishort) *Ishort: Short circuit current

Peripheral Circuit Considerations ・Vcc Terminal Please attach a capacitor (greater than 0.33µF) between the Vcc and GND. The capacitance values will differ depending on the application, so please take this into account when configuring the terminal. ・GND Terminal Please be sure to keep the set ground and IC ground at the same potential level so that a potential difference does not arise between them. If a potential difference arises between the set ground and th e IC ground, the preset vo ltage will not be outputted, causing the system to become unstable. Therefore, please reduce the impedance by making the ground patterns as wide as possible and by reducing the distance between the set ground and the IC ground as much as possible. ・CTL Terminal The CTL terminal is turned ON at 2.0V and higher and OFF at 0.8V and lower within the operating power supply voltage range. The power supply and the CTL terminal may be started up and shut down in any order without problems.
Vo Terminal Fig.32 Output Equivalent Circuit Fig.33 ESR-Io Characteristics Fig.34 ESR vs. Io Characteristics ( B A x x C C 0 ) ( B A x x D D 0 ) Please attach an anti-oscillation capacitor between V o and GND. The capacitance of the capacitor may significantly change due to factors such as temperature changes, making it impossi ble to completely stop oscillations. Please use a tantalum capacitor or aluminum electrolysis capacitor with favorable c haracteristics and small internal series resistance (ESR) even at low temperatures. The output fluctuates regardless of whether the ESR is large or small. Please use the IC within the stable operating region while referring to the ESR characteristics reference data shown in Fig.32 through 34. In applications where there are sudden load fluctuations, the use of a capacitor with large capacitance is recommended. Pd – Vcc×Icca Vcc－Vo Vcc： Vo： Io： Vcca： Input voltage Output voltage Load current Circuit current 1.04－8.3×Icca OUT 22μF IC OUTPUT CURRENT：lo(mA) 10000 1 0.1 Unstable operating region Unstable operating region Stable operating region EFFECTIVE SERIES RESISTANCE:ESR [Ω] 10 100 1000 100 200 400 800 1000 0.1 Stable operating region 0 600 Unstable operating region Unstable operating region OUTPUT CURRENT：lo(mA) EFFECTIVE SERIES RESISTANCE:ESR [Ω] 100

Operational Notes 1) Protection Circuits Over-current Protection Circuit A built-in over-current protection circuit corresponding to the current capacity prevents the destruction of the IC when there are load shorts. This protection circuit is a “7”-shaped current control circuit that is designed such that the current is restricted and does not latch even when a large current momentarily flows through the system with a high-capacitance capacitor. However, while this protection circuit is effective for the preven tion of destruction due to unex pected accidents, it is not suitable for continuous operation or transient use. Please be aware when creating thermal designs that the overcurrent protection circuit has negative current capacity characteristics with regard to temperature (Refer to Fig.6 and 18). Thermal Shutdown Circuit (Thermal Protection) This system has a built-in temperature protection circuit for the purpose of protecting the IC from thermal damage. As shown above, this must be used within the range of a cceptable loss, but if the acceptable loss happens to be continuously exceeded, the chip temperature Tj increases, causing the temperature protection circuit to operate. When the thermal shutdown circuit operat es, the operation of the circuit is su spended. The circuit resumes operation immediately after the chip temperatur e Tj decreases, so the output repeats t he ON and OFF states (Please refer to Fig.14 and 26 for the temperatures at which the temperature protection circuit operates). There are cases in which the IC is destroyed due to thermal runa way when it is left in the ov erloaded state. Be sure to avoid leaving the IC in the overloaded state. Reverse Current In order to prevent the destruction of t he IC when a reverse current flows through the IC, it is recommended that a diode be placed between the Vcc and Vo and a pathway be created so that the current can escape (Refer to Fig.35). Fig.35 Bypass diode 2) This IC is bipolar IC that has a P-board (substrate) and P+ isolation layer bet ween each devise, as shown in Fig.36. A P-N junction is formed between this P-layer and the N-layer of each device, and the P-N junction operates as a parasitic diode when the electric potential relationship is GND> Pin A, GND> Pin B, while it operates as a parasitic transistor when the electric potential relationship is Pin B GND> Pin A. Para sitic devices are structurally inevitable in the IC. The operation of parasitic devices induces mu tual interference between circuits, causing malfunctions and eventually the destruction of the IC. It is necessary to be careful not to use the IC in ways that would cause parasitic elements to operate. For example, applying a voltage that is lower than the GND (P-board) to the input terminal. Status of this document The Japanese version of this document is fo rmal specification. A customer may use this translation version only for a reference to help reading the formal version. If there are any differences in translation version of this doc ument formal version takes priority. OUT Vcc CTL GND Reverse current Fig.36 Example of the basic structure of a bipolar IC (Pin A) GND N Resistor Parasitic element P N P P+ N (Pin A) Parasitic element or transistor (Pin B) GND C B E Parasitic element GND GND N P N Parasitic element or transistor (Pin B) B E Transistor (NPN) N P N GND C

Physical Dimension Tape and Reel Information (Unit : mm) TO252-3 2 1 3 0.8 0.65 0.65 1.5 2.5 0.75 FIN 6.5±0.2 2.3±0.2 2.3±0.2 0.5±0.1 1.0±0.2 2.3±0.2 9.5±0.5 0.5±0.1 5.5±0.2 1.5±0.2 5.1+0.2 -0.1 C0.5 Direction of feed1pin Reel ∗ Order quantity needs to be multiple of the minimum quantity. <Tape and Reel information> Embossed carrier tapeTape Quantity Direction of feed The direction is the 1pin of product is at the lower left when you hold reel on the left hand and you pull out the tape on the right hand 2000pcs ( ) (Unit : mm) TO252-5 1 2 3 54 0.8 0.5 1.27 1.5 2.5 FIN 6.5±0.2 2.3±0.2 0.5±0.1 1.0±0.2 9.5±0.5 0.5±0.1 5.5±0.2 1.5±0.2 C0.5 5.1+0.2 -0.1 Direction of feed1pin Reel ∗ Order quantity needs to be multiple of the minimum quantity. <Tape and Reel information> Embossed carrier tapeTape Quantity Direction of feed The direction is the 1pin of product is at the lower left when you hold reel on the left hand and you pull out the tape on the right hand 2000pcs ( ) Direction of feed 1pin Reel ∗ Order quantity needs to be multiple of the minimum quantity. <Tape and Reel information> Embossed carrier tapeTape Quantity Direction of feed 2000pcs TR ( )The direction is the 1pin of product is at the upper right when you hold reel on the left hand and you pull out the tape on the right hand (Unit : mm) HRP5 S 0.08 S (MAX 9.745 include BURR) 5 4 3 21 1.905±0.1 0.8 35±0.2 1.523±0.15 10.54±0.13 −0.05 +0.10.27 4.5° (6.5) 8.82 ± 0.1 9.395±0.125 0.73±0.1 1.72 0.08±0.05 (7.49) 8.0±0.13 1.017±0.2 1.2575 −4.5°+5.5° (Unit : mm) TO220FP-3 231 +0.4 φ3.2±0.1 0.55 17.0 12.0±0.2 8.0±0.2 2.54±0.5 13.5Min. 5.0±0.2 0.8 2.54±0.5 1.3 −0.1 +0.3 10.0 7.0 1.8±0.2 −0.2 −0.1 +0.3 2.6±0.5 −0.05 +0.1 +0.2 −0.1 −0.1 +0.34.5 2.8 ∗ Order quantity needs to be multiple of the minimum quantity. <Tape and Reel information> TubeContainer Quantity Direction of feed 500pcs Direction of products is fixed in a container tube

Marking Diagrams (Unit : mm) TO220FP-5 7.0 10.0 2.8 4.5 1.778 0.5±0.1 1.2 0.8 1.8±0.28.0±0.2 0.7 12.0±0.2 17.013.5Min. φ3.2±0.1 −0.2 +0.4 +0.3 −0.1 −0.1 +0.2+0.3 −0.1 +0.3 −0.1 23451 2.85 ∗ Order quantity needs to be multiple of the minimum quantity. <Tape and Reel information> TubeContainer Quantity Direction of feed 500pcs Direction of products is fixed in a container tube HRP5 (TOP VIEW) Part Number Marking LOT Number 1PIN MARK TO220FP-3 (TOP VIEW) Part Number Marking LOT Number TO220FP-5 (TOP VIEW) Part Number Marking LOT Number TO252-3 (TOP VIEW) Part Number Marking LOT Number TO252-5 (TOP VIEW) Part Number Marking LOT Number

TSZ02201-0R6R0A600130-1-2© 2012 ROHM Co., Ltd. All rights reserved. TSZ22111･15･001 26.Jun.2012 Rev.001 www.rohm.com ■1A output BAxxCC0xx Series Orderable Part Number Package Part Number Marking BA033CC0WFP-E2 TO252-5 033CC0W BA05CC0WFP-E2 05CC0W BA06CC0WFP-E2 06CC0W BA07CC0WFP-E2 07CC0W BA08CC0WFP-E2 08CC0W BA09CC0WFP-E2 09CC0W BAJ2CC0WFP-E2 J2CC0W BA03CC0WT TO220FP-5 03CC0W BA033CC0WT 033CC0W BA05CC0WT 05CC0W BA07CC0WT 07CC0W BA08CC0WT 08CC0W BA09CC0WT 09CC0W BAJ0CC0WT J0CC0W BAJ2CC0WT J2CC0W BA03CC0FP-E2 TO252-3 03CC0 BA033CC0FP-E2 033CC0 BA05CC0FP-E2 05CC0 BA06CC0FP-E2 06CC0 BA07CC0FP-E2 07CC0 BA08CC0FP-E2 08CC0 BA09CC0FP-E2 09CC0 BAJ0CC0FP-E2 J0CC0 BAJ2CC0FP-E2 J2CC0 BAJ5CC0FP-E2 J5CC0 BA03CC0T TO220FP-3 03CC0 BA033CC0T 033CC0 BA05CC0T 05CC0 BA06CC0T 06CC0 BA07CC0T 07CC0 BA08CC0T 08CC0 BA09CC0T 09CC0 BAJ0CC0T J0CC0 BAJ2CC0T J2CC0 BAJ5CC0T J5CC0

TSZ02201-0R6R0A600130-1-2© 2012 ROHM Co., Ltd. All rights reserved. TSZ22111･15･001 26.Jun.2012 Rev.001 www.rohm.com ■2A output BAxxDD0xx Series Orderable Part Number Package Part Number Marking BA15DD0WT TO220FP-5 15DD0W BA18DD0WT 18DD0W BA25DD0WT 25DD0W BA30DD0WT 30DD0W BA33DD0WT 33DD0W BA50DD0WT 50DD0W BA90DD0WT 90DD0W BAJ2DD0WT J2DD0W BAJ6DD0WT J6DD0W BA15DD0WHFP-TR HRP5 15DD0W BA18DD0WHFP-TR 18DD0W BA25DD0WHFP-TR 25DD0W BA30DD0WHFP-TR 30DD0W BA33DD0WHFP-TR 33DD0W BA50DD0WHFP-TR 50DD0W BA90DD0WHFP-TR 90DD0W BAJ2DD0WHFP-TR J2DD0W BAJ6DD0WHFP-TR J6DD0W BA15DD0T TO220FP-3 15DD0 BA18DD0T 18DD0 BA25DD0T 25DD0 BA30DD0T 30DD0 BA33DD0T 33DD0 BA50DD0T 50DD0 BA90DD0T 90DD0 BAJ2DD0T J2DD0 BAJ6DD0T J6DD0

Revision History Date Revision Changes 26.Jun.2012 001 New Release

General Precaution 1) Before you use our Products, you are requested to care fully read this document and fully understand its contents. ROHM shall not be in any way responsible or liable for fa ilure, malfunction or accident arising from the use of any ROHM’s Products against warning, caution or note contained in this document. 2) All information contained in this document is current as of the issuing date and subjec t to change without any prior notice. Before purchasing or using ROHM’s Products, please confirm the la test information with a ROHM sales representative.
Precaution on using ROHM Products 1) Our Products are designed and manufactured for applicat ion in ordinary electronic equipments (such as AV equipment, OA equipment, telecommunication equipment, home electroni c appliances, amusement equipment, etc.). If you intend to use our Products in devices requiring extremel y high reliability (such as medical equipment, transport equipment, traffic equipment, aircraft/spacecraft, nuclear power controllers, fuel controllers, car equipment including car accessories, safety devices, etc.) and whose malfunction or failure may cause loss of human life, bodily injury or serious damage to property (“Specific Applications”), please consult with the ROHM sale s representative in advance. Unless otherwise agreed in writing by ROHM in advance, ROHM shall not be in any way responsible or liable for any damages, expenses or losses incurred by you or third parties arising from the use of any ROHM’s Products for Specific Applications. 2) ROHM designs and manufactures its Products subject to strict quality control system. However, semiconductor products can fail or malfunction at a certain rate. Please be sure to implement, at your own responsibilities, adequate safety measures including but not limited to fail-safe desi gn against the physical injury, damage to any property, which a failure or malfunction of our Products may cause. The following are examples of safety measures: [a] Installation of protection circuits or other protective devices to improve system safety [b] Installation of redundant circuits to reduce the impact of single or multiple circuit failure 3) Our Products are designed and manufactured for use under standard conditions and not under any special or extraordinary environments or conditio ns, as exemplified below. Accordin gly, ROHM shall not be in any way responsible or liable for any damages, expenses or losses arising from the use of an y ROHM’s Products under any special or extraordinary environments or conditions. If you intend to use our Products under any special or extraordinary environments or conditions (as exemplified below), your independent verification and confirmation of product performance, reliability, etc, prior to use, must be necessary: [a] Use of our Products in any types of liquid, including water, oils, chemicals, and organic solvents [b] Use of our Products outdoors or in places where the Products are exposed to direct sunlight or dust [c] Use of our Products in places where the Products ar e exposed to sea wind or corrosive gases, including Cl H2S, NH3, SO2, and NO2 [d] Use of our Products in places where the Products are exposed to static electricity or electromagnetic waves [e] Use of our Products in proximity to heat-producing components, plastic cords, or other flammable items [f] Sealing or coating our Products with resin or other coating materials [g] Use of our Products without cleaning residue of flux (ev en if you use no-clean type fluxes, cleaning residue of flux is recommended); or Washing our Products by using water or water-soluble cleaning agents for cleaning residue after soldering [h] Use of the Products in places subject to dew condensation 4) The Products are not subjec t to radiation-proof design. 5) Please verify and confirm characteristics of the final or mounted products in using the Products. 6) In particular, if a transient load (a large amount of load applied in a short per iod of time, such as pulse) is applied, confirmation of performance characteristics after on-boar d mounting is strongly recomm ended. Avoid applying power exceeding normal rated power; exceeding the power rating under steady-state loading condition may negatively affect product performance and reliability. 7) De-rate Power Dissipation (Pd) depending on Ambient temper ature (Ta). When used in sealed area, confirm the actual ambient temperature. 8) Confirm that operation temperature is within the specified range described in the product specification. 9) ROHM shall not be in any way responsible or liable for failure induced under deviant condi tion from what is defined in this document.

Precaution for Mounting / Circuit board design 1) When a highly active halogenous (chlori ne, bromine, etc.) flux is used, the residue of flux may negatively affect product performance and reliability. 2) In principle, the reflow soldering method must be used; if flow soldering method is preferred, please consult with the ROHM representative in advance. For details, please refer to ROHM Mounting specification
Precautions Regarding Application Examples and External Circuits 1) If change is made to the constant of an external circuit, pl ease allow a sufficient margin considering variations of the characteristics of the Products and external components, including transient characteri stics, as well as static characteristics. 2) You agree that application notes, re ference designs, and associated data and in formation contained in this document are presented only as guidance for Products use. Theref ore, in case you use such information, you are solely responsible for it and you must exercise your own independent verification and judgment in the use of such information contained in this document. ROHM shall not be in any way responsible or liable for any damages, expenses or losses incurred by you or third parties arising from the use of such information.
Precaution for Electrostatic This Product is electrostatic sensitive product, which may be damaged due to electrostatic discharge. Please take proper caution in your manufacturing process and storage so that voltage exceeding t he Products maximum rating will not be applied to Products. Please take special care under dry condit ion (e.g. Grounding of human body / equipment / solder iron, isolation from charged objects, setting of Ionizer, friction prevention and temperature / humidity control).
Precaution for Storage / Transportation 1) Product performance and soldered connections may deteriora te if the Products are stored in the places where: [a] the Products are exposed to sea winds or corros ive gases, including Cl2, H2S, NH3, SO2, and NO2 [b] the temperature or humidity exceeds those recommended by ROHM [c] the Products are exposed to di rect sunshine or condensation [d] the Products are exposed to high Electrostatic 2) Even under ROHM recommended storage c ondition, solderability of products out of recommended storage time period may be degraded. It is strongly recommended to confirm sol derability before using Products of which storage time is exceeding the recommended storage time period. 3) Store / transport cartons in the co rrect direction, which is indicated on a carton with a symbol. Otherwise bent leads may occur due to excessive stress applied when dropping of a carton. 4) Use Products within the specified time after opening a humidity barrier bag. Baking is required before using Products of which storage time is exceeding the recommended storage time period.
Precaution for Product Label QR code printed on ROHM Products label is for ROHM’s internal use only.
Precaution for Disposition When disposing Products please dispose them properly using an authorized industry waste company.
Precaution for Foreign Exchange and Foreign Trade act Since our Products might fall under cont rolled goods prescribed by the applicable foreign exchange and foreign trade act, please consult with ROHM representative in case of export.
Precaution Regarding Intellectual Property Rights 1) All information and data including but not limited to application example contained in this document is for reference only. ROHM does not warrant that foregoi ng information or data will not infringe any intellectual property rights or any other rights of any third party regarding such information or data. ROHM shall not be in any way responsible or liable for infringement of any intellectual property rights or other damages arising from use of such information or data.: No license, expressly or implied, is granted hereby under any intellectual property rights or other rights of ROHM or any third parties with respect to the information contained in this document.

Other Precaution 1) The information contained in this document is provi ded on an “as is” basis and ROHM does not warrant that all information contained in this document is accurate and/or error-free. ROHM shall not be in any way responsible or liable for any damages, expenses or losses incurred by you or third parties resulting from inaccuracy or errors of or concerning such information. 2) This document may not be reprinted or reproduced, in whol e or in part, without prior written consent of ROHM. 3) The Products may not be disassembled, converted, modified, reproduced or otherwise changed without prior written consent of ROHM. 4) In no event shall you use in any way whatsoever the Pr oducts and the related technical information contained in the Products or this document for any military purposes, incl uding but not limited to, the development of mass-destruction weapons. 5) The proper names of companies or products described in this document are trademarks or registered trademarks of ROHM, its affiliated companies or third parties.

Product Information

BA03CC0FP-E2 specifications and overview.

Summary

Low-saturation regulators, available for output s up to 2A/1A.

Description

Low-saturation regulators, available for output s up to 2A/1A.

Source title BA03CC0FP-E2 Datasheet(PDF) - Rohm

Related Parts

More parts from the same family.

Browse manufacturer