B1000R MPD | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 2
Technical content
/square6 5 VDC Input /square6 1500 VDC Isolation /square6 10W Output Power /square6 Tightly Regulated Dual Outputs /square6 Meets EN55022 Class “A” /square6 Low Cost Electrical Specifi cations Specifi cations typical @ +251C with nominal input voltage & rated output current, unless otherwise noted. Specifi cations subject to change without notice. Input Parameter Conditions Min. Typ. Max. Units Input Voltage Range 4.5 5.0 5.5 VDC Input Filter π (Pi) Filter (Complies with EN55022 Class A) Reverse Polarity Input Current 2.0 A Short Circuit Input Power 3,500 4,500 mW Output Parameter Conditions Min. Typ. Max. Units Output Voltage Accuracy !0.5 !1.0 % Output Voltage Balance Dual Output , Balanced Loads !0.2 !0.5 % Line Regulation Vin = Min to Max !0.1 % Load Regulation Iout = 10% to 100% !0.15 % Ripple & Noise (20 MHz) 20 30 mV P - P Output Power Protection 150 % Transient Recovery Time (Note 1) 25% Load Step Change 200 µSec Transient Response Deviation !4.0 % Temperature Coeffi cient !0.01 !0.02 %/1C Output Short Circuit Continuous General Parameter Conditions Min. Typ. Max. Units Isolation Voltage 60 Seconds 1,500 VDC Isolation Resistance 500 VDC 1,000 M Ω Isolation Capacitance 100 kHz, 1V 500 600 pF Switching Frequency 270 280 290 kHz Environmental Parameter Conditions Min. Typ. Max. Units Operating Temperature Range -40 +25 +71 1C Storage Temperature Range -40 +125 1C Cooling Free Air Convection Humidity RH, Non-condensing 95 % RFI Six-Sided Shielded, Metal Case Conducted EMI EN55022 Class A Physical Case Material Metal with Non-Conductive Base Weight 1.06 Oz (30g) Reliability Specifi cations Parameter Conditions Min. Typ. Max. Units MTBF MIL HDBK 217F, 251C, Gnd Benign 700 kHours Absolute Maximum Ratings Parameter Conditions Min. Typ. Max. Units Input Voltage Surge (1 Sec) -0.7 7.5 VDC Internal Power Dissipation 5,000 mW Caution: Exceeding Absolute Maximum Ratings may damage the module. These are not continuous operating ratings. MicroPower Direct 10W, 5 VDC Input Compact, Dual Output DC/DC Converters B1000R Series MicroPower Direct /square6 TEL: (781) 344-8226 /square6 FAX: (781) 344-8481 /square6 E-Mail: sales@micropowerdirect.com /square6 WEB: www/micropowerdirect.com
Notes: All dimensions are typical in inches (mm) Tolerance x.xx = !0.01 (!0.25) Model Number Input Output Effi ciency (%, Typ) Fuse Rating Slow-Blow (mA) Voltage (VDC) Current (mA) Refl ected Ripple Current (mA, Typ) Voltage (VDC) Current (mA, Max) Current (mA, Min)Nominal Range Full-Load No-Load B1001R 5 4.5 - 5.5 2,500 30 >50 !12.0 !415 !42 78 5,000 B1002R 5 4.5 - 5.5 2,538 30 >50 !15.0 !330 !33 78 5,000 B1003R 5 4.5 - 5.5 2,669 60 >50 !18.0 !278 !28 75 5,000
232 Tosca Drive, Stoughton, MA 02072
www.micropowerdirect.com sales@micropowerdirect.com phone: (781) 344 - 8226 * fax: (781) 344 - 8481 Mechanical Dimensions MicroPower Direct Pin Function 1+ V i n 2- V i n 3+ V o u t
4 Common
µF Max !1,000 Capacitive Load Model Selection Guide Notes: 1. Transient recovery is measured to within a 1% error band for a load step change of 75% to 100%. 2. When measuring output ripple, it is recommended that an external 0.47 µF ceramic capacitor be placed from each output (pin 3 & pin 5) to common (pin 4). 3. Dual output units may be connected to provide a 24 VDC, 30 VDC or 36 VDC output. To do this, connect the load across the posi- tive (+Vout) and negative (-Vout) outputs and fl oat the output common. 100 -40 -20 0 5 15 25 35 45 65 75 85 95 105 Output Power % Ambient Temperature ( C) 0.40 (10.2) 0.40 (10.2) 0.10 (2.54) 0.80 (20.3) 0.60 (15.2) 0.40 (10.2) 0.40 (10.2) 1.00 (25.4) 2.00 (50.8) 0.40 (10.2) 0.24 (6.0) 0.04 (1.0) Bottom Side Dia Derating Curve