DATASHEET SEARCH SITE | WWW.ALLDATASHEET.COM

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 13

Technical content

Features

 Small signal gain amplifi er  Operating frequency DC to 6 GHz  Unconditionally stable  50 Ohm input & output  Flat, Broadband Frequency Response up to 2 GHz  Industry standard SOT-363  Lead-free, RoHS compliant, Green Specifi cations

2 GHz, 5V Vcc, 48mA (typical)

 19.5 dB Gain  15.1 dBm P1dB  26.5 dBm OIP3  3.2 dB NF  10 dB IRL and ORL

Applications

 Cellular / PCS / 3G base station  Wireless Data / WLAN  WiMAX / WiBRO  CATV & Cable modem  ISM Top View GND GND 53X Input GND GND Output & Vd

Absolute Maximum Rating[1] TA=25°C Symbol Parameter Units Absolute Max. Id Device Current mA 80 PIN,MAX CW RF Input Power dBm 18 PDISS Total Power Dissipation [3] mW 327 TOPT Operating Temperature °C -40 to 85 TJ,MAX Junction Temperature °C 150 TSTG Storage Temperature °C -65 to 150 Thermal Resistance Thermal Resistance [2] jc = 184°C/W (Id = 48 mA, Tc = 85°C) Notes: 1. Operation of this device in excess of any of these limits may cause permanent damage. 2. Thermal resistance measured using Infrared measurement technique. 3. Ground lead temperature is 25°C. Derate 5.5mW/°C for T c >90°C. Electrical Specifi cations [1] TA = 25°C, Zo = 50 , VCC = 5 V, Rbias = 22 , Pin = -15 dBm (unless specifi ed otherwise) Symbol Parameter and Test Condition Frequency Units Min. Typ. Max. Id Device Current mA 44.0 47.6 51.0 Gp Power Gain 900 MHz

2000 MHz

18.0 21.8 19.5 21.0 OIP3 [2] Output 3rd Intercept Point 900 MHz 25.0 28.9 26.5 S11 Input Return Loss, 50 source 900 MHz dB -16.5 -12.0 S22 Output Return Loss, 50 load 900MHz dB -17.3 -13.4 S12 Reverse Isolation 900 MHz dB -24.3 -24.7 P1dB Output Power at 1dB Gain Compression 900 MHz dBm 16.0 15.1 NF Noise Figure 900 MHz dB 2.9 3.2 Notes: 1. Measurements obtained on CPWG line with reference plane at the ends of DUT leads (as shown in Figure 1). 2. OIP3 test condition: F RF1 - FRF2 = 10MHz with input power of -23 dBm per tone measured at worse side band.

Figure 22. S11 vs Frequency and Id Figure 23. S22 vs Frequency and Id

AVT-53663 Typical Scattering Parameters TA = 25°C, Zo = 50 , Id = 30 mA, (unless specifi ed otherwise) Frequency GHz S11 S21 S12 S22 Mag Angle dB Mag Angle Mag Angle Mag Angle K Notes: 1. S-parameters are measured on a CPWG line fabricated on 0.025 inch thick Rogers® RO4350 material. The input reference plane is at the end of the input lead. The output reference plane is at the end of the output lead.

AVT-53663 Typical Scattering Parameters TA = 25°C, Zo = 50 , Id = 48 mA, (unless specifi ed otherwise) Frequency GHz S11 S21 S12 S22 Mag Angle dB Mag Angle Mag Angle Mag Angle K Notes: 1. S-parameters are measured on a CPWG line fabricated on 0.025 inch thick Rogers® RO4350 material. The input reference plane is at the end of the input lead. The output reference plane is at the end of the output lead.

AVT-53663 Typical Scattering Parameters TA = 25°C, Zo = 50 , Id = 60 mA, (unless specifi ed otherwise) Frequency GHz S11 S21 S12 S22 Mag Angle dB Mag Angle Mag Angle Mag Angle K Notes: 1. S-parameters are measured on a CPWG line fabricated on 0.025 inch thick Rogers® RO4350 material. The input reference plane is at the end of the input lead. The output reference plane is at the end of the output lead.

Part Number Ordering Information Part Number No. of Devices Container AVT-53663-TR1G 3000 7” Reel AVT-53663-BLKG 100 Antistatic bag Package Dimensions Outline 63 (SOT-363/SC-70) Recommended PCB Pad Layout for Avago’ s SC70 6L/SOT-363 Products Notes: 1. All dimensions are in mm. 2. Dimensions are inclusive of plating. 3. Dimensions are exclusive of mold fl ash & metal burr. 4. All specifi cations comply to EIAJSC70. 5. Die is facing up for mold and facing down for trim/form, ie: reverse trim/form. 6. Package surface to be mirror fi nish. 0.650BCS. Symbol Dimensions (mm) Min Max E 1.15 1.35 D 1.80 2.25 HE 1.80 2.40 A 0.80 1.10 A2 0.80 1.00 A1 0.00 0.10 Q1 0.10 0.40 e 0.65 b 0.15 0.30 c 0.08 0.25 L 0.10 0.46 EHE D e b AA2 L c 0.026 0.079 0.018 0.039 Dimensions in inches.

Tape Dimensions and Product Orientation for Outline 63 P F W C D E 10° MAX. t1 (CARRIER TAPE THICKNESS) Tt (COVER TAPE THICKNESS) 10° MAX. B 0 KO DESCRIPTION SYMBOL SIZE (mm) SIZE (INCHES) LENGTH WIDTH DEPTH PITCH BOTTOM HOLE DIAMETER A P 2.40 ± 0.10 2.40 ± 0.10 1.20 ± 0.10 4.00 ± 0.10 1.00 + 0.25 0.094 ± 0.004 0.094 ± 0.004 0.047 ± 0.004 0.157 ± 0.004 0.039 + 0.010 CAVITY DIAMETER PITCH POSITION D E 1.55 ± 0.05 4.00 ± 0.10 1.75 ± 0.10 0.061 ± 0.002 0.157 ± 0.004 0.069 ± 0.004 PERFORATION WIDTH THICKNESS W 8.00 ± 0.30 0.254 ± 0.02 0.315 ± 0.012 0.0100 ± 0.0008 CARRIER TAPE CAVITY TO PERFORATION (WIDTH DIRECTION) CAVITY TO PERFORATION (LENGTH DIRECTION) F 3.50 ± 0.05 2.00 ± 0.05 0.138 ± 0.002 0.079 ± 0.002 DISTANCE WIDTH TAPE THICKNESS C Tt 5.4 ± 0.10 0.062 ± 0.001 0.205 ± 0.004 0.0025 ± 0.0004 COVER TAPE

For product information and a complete list of distributors, please go to our web site: www.avagotech.com Avago, Avago Technologies, and the A logo are trademarks of Avago Technologies in the United States and other countries. Data subject to change. Copyright © 2005-2011 Avago Technologies. All rights reserved. AV02-2359EN - September 29, 2011 Reel Dimension 7 inch