DATASHEET SEARCH SITE | WWW.ALLDATASHEET.COM

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 13

Technical content

Features

  • Small signal gain amplifier
  • Operating frequency DC to 6 GHz
  • Unconditionally stable
  • 50 Ohm input & output
  • Flat, Broadband Frequency Response up to 2 GHz
  • Industry standard SOT-363
  • Lead-free, RoHS compliant, Green Specifications

2 GHz, 5V Vcc, 36mA (typical)

  • 15.3 dB Gain
  • 12.5 dBm P1dB
  • 25 dBm OIP3
  • 4 dB NF
  • 15 dB IRL and ORL

Applications

  • Cellular / PCS / 3G base station
  • Wireless Data / WLAN
  • WiMAX / WiBRO
  • CATV & Cable modem
  • ISM Typical Biasing Configuration Pin 1, 2, 4, 5 (GND) Pin 6 Pin 3 CbypRbias Cblock Cblock Vd RFin RFout VCC = 5V Rbias = (VCC - Vd)/IdCbyp Top View GND GND 50X Input GND GND Output & Vd

Symbol Parameter Units Absolute Max.

  1. Operation of this device in excess of any of

these limits may cause permanent damage.

  1. Thermal resistance measured using Infrared
  2. Ground lead temperature is 25°C. Derate

Symbol Parameter and Test Condition Frequency Units Min. Typ. Max.

2000 MHz

  1. Measurements obtained on CPWG line with reference plane at the ends of DUT leads (as shown in Figure 1).

RF1 - FRF2 = 10MHz with input power of -15 dBm per tone measured at worse side band. Figure 1. Block diagram of board used for Id, Gain, OIP3, S11, S22, S12, OP1dB and NF measurements. Circuit losses have been de-embedded from actual measurements.

Figure 22. S11 vs Frequency and Id Figure 23. S22 vs Frequency and Id

AVT-50663 Typical Scattering Parameters TA = 25°C, Zo = 50 Ω, Id = 20 mA, (unless specified otherwise) Id=20mA S11 S21 S12 S22 Kmag angle dB mag angle mag angle mag angle Notes: 1. S-parameters are measured on a CPWG line fabricated on 0.025 inch thick Rogers ® RO4350 material. The input reference plane is at the end of the input lead. The output reference plane is at the end of the output lead.

AVT-50663 Typical Scattering Parameters TA = 25°C, Zo = 50 Ω, Id = 36 mA, (unless specified otherwise) Id=36mA S11 S21 S12 S22 Kmag angle dB mag angle mag angle mag angle Notes: 1. S-parameters are measured on a CPWG line fabricated on 0.025 inch thick Rogers ® RO4350 material. The input reference plane is at the end of the input lead. The output reference plane is at the end of the output lead.

AVT-50663 Typical Scattering Parameters TA = 25°C, Zo = 50 Ω, Id = 45 mA, (unless specified otherwise) Id=45mA S11 S21 S12 S22 Kmag angle dB mag angle mag angle mag angle Notes: 1. S-parameters are measured on a CPWG line fabricated on 0.025 inch thick Rogers ® RO4350 material. The input reference plane is at the end of the input lead. The output reference plane is at the end of the output lead.

Part Number Ordering Information Part Number No. of Devices Container AVT-50663-TR1G 3000 7” Reel AVT-50663-BLKG 100 Antistatic Bag Package Dimensions Outline 63 (SOT-363/SC-70) Recommended PCB Pad Layout for Avago's SC70 6L/SOT-363 Products EHE D e b AA2 L c DIMENSIONS (mm) MIN. 1.15 1.80 1.80 0.80 0.80 0.00 0.10 0.15 0.10 0.10 MAX. 1.35 2.25 2.40 1.10 1.00 0.10 0.40 0.30 0.25 0.46 SYMBOL E D HE A e b c L Notes: 1. All dimensions are in mm. 2. Dimensions are inclusive of plating. 3. Dimensions are exclusive of mold flash & metal burr. 4. All specifications comply to EIAJSC70. 5. Die is facing up for mold and facing down for trim/form, ie: reverse trim/form. 6. Package surface to be mirror finish. 0.650BCS. 0.65 0.026 0.079 0.018 0.039 Dimensions in inches.

Tape Dimensions and Product Orientation for Outline 63 P F W C D E 10 MAX. t1 (CARRIER TAPE THICKNESS) Tt (COVER TAPE THICKNESS) 10 MAX. DESCRIPTION SYMBOL SIZE (mm) SIZE (INCHES) LENGTH WIDTH DEPTH PITCH BOTTOM HOLE DIAMETER A P 2.40 0.10 2.40 0.10 1.20 0.10 4.00 0.10 1.00 + 0.25 0.094 0.004 0.094 0.004 0.047 0.004 0.157 0.004 0.039 + 0.010 CAVITY DIAMETER PITCH POSITION D P E 1.50 0.10 4.00 0.10 1.75 0.10 0.061 + 0.002 0.157 0.004 0.069 0.004 PERFORATION WIDTH THICKNESS W t 8.00 + 0.30 - 0.10 0.254 0.02 0.315 + 0.012 0.0100 0.0008 CARRIER TAPE CAVITY TO PERFORATION (WIDTH DIRECTION) CAVITY TO PERFORATION (LENGTH DIRECTION) F P 3.50 0.05 2.00 0.05 0.138 0.002 0.079 0.002 DISTANCE WIDTH TAPE THICKNESS C Tt 5.40 0.10 0.062 0.001 0.205 + 0.004 0.0025 0.0004 COVER TAPE USER FEED DIRECTION COVER TAPE CARRIER TAPE REEL END VIEW 8 mm 4 mm TOP VIEW (Package marking example orientation shown.) 2Kx 2Kx 2Kx 2Kx50X 50X 50X 50X

For product information and a complete list of distributors, please go to our web site: www.avagotech.com Avago, Avago Technologies, and the A logo are trademarks of Avago Technologies in the United States and other countries. Data subject to change. Copyright © 2005-2009 Avago Technologies. All rights reserved. AV02-2244EN - December 1, 2009 Reel Dimension 7 inch