ATTINY13A-SH

ATTINY13A_10 ATMEL | Alldatasheet

Document overview

• Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
• PDF pages: 20

Technical content

Features

• High Performance, Low Power AVR® 8-Bit Microcontroller
• Advanced RISC Architecture – 120 Powerful Instructions – Most Single Clock Cycle Execution – 32 x 8 General Purpose Working Registers – Fully Static Operation – Up to 20 MIPS Througput at 20 MHz
• High Endurance Non-volatile Memory segments – 1K Bytes of In-System Self-programmable Flash program memory – 64 Bytes EEPROM – 64 Bytes Internal SRAM – Write/Erase Cycles: 10,000 Flash/100,000 EEPROM – Data retention: 20 Years at 85°C/100 Years at 25°C (see page 6) – Programming Lock for Self-Programming Flash & EEPROM Data Security
• Peripheral Features – One 8-bit Timer/Counter with Prescaler and Two PWM Channels – 4-channel, 10-bit ADC with Internal Voltage Reference – Programmable Watchdog Timer with Separate On-chip Oscillator – On-chip Analog Comparator
• Special Microcontroller Features – debugWIRE On-chip Debug System – In-System Programmable via SPI Port – External and Internal Interrupt Sources – Low Power Idle, ADC Noise Reduction, and Power-down Modes – Enhanced Power-on Reset Circuit – Programmable Brown-out Detection Circuit with Software Disable Function – Internal Calibrated Oscillator
• I/O and Packages – 8-pin PDIP/SOIC: Six Programmable I/O Lines – 10-pad MLF: Six Programmable I/O Lines – 20-pad MLF: Six Programmable I/O Lines
• Operating Voltage: – 1.8 – 5.5V
• Speed Grade: – 0 – 4 MHz @ 1.8 – 5.5V – 0 – 10 MHz @ 2.7 – 5.5V – 0 – 20 MHz @ 4.5 – 5.5V
• Industrial Temperature Range
• Low Power Consumption – Active Mode:
• 190 µA at 1.8 V and 1 MHz –I d l e M o d e :
• 24 µA at 1.8 V and 1 MHz 8-bit Microcontroller with 1K Bytes In-System Programmable Flash ATtiny13A Summary Rev. 8126ES–AVR–07/10

8126ES–AVR–07/10 ATtiny13A 1. Pin Configurations Figure 1-1. Pinout of ATtiny13A (PCINT5/RESET/ADC0/dW) PB5 (PCINT3/CLKI/ADC3) PB3 (PCINT4/ADC2) PB4 GND VCC PB2 (SCK/ADC1/T0/PCINT2) PB1 (MISO/AIN1/OC0B/INT0/PCINT1) PB0 (MOSI/AIN0/OC0A/PCINT0) 8-PDIP/SOIC 20-QFN/MLF (PCINT5/RESET/ADC0/dW) PB5 (PCINT3/CLKI/ADC3) PB3 DNC DNC (PCINT4/ADC2) PB4 DNC DNC GND DNC DNC VCC PB2 (SCK/ADC1/T0/PCINT2) DNC PB1 (MISO/AIN1/OC0B/INT0/PCINT1) PB0 (MOSI/AIN0/OC0A/PCINT0) DNC DNC DNC DNC DNC NOTE: Bottom pad should be soldered to ground. DNC: Do Not Connect 10-QFN/MLF (PCINT5/RESET/ADC0/dW) PB5 (PCINT3/CLKI/ADC3) PB3 DNC (PCINT4/ADC2) PB4 GND VCC PB2 (SCK/ADC1/T0/PCINT2) DNC PB1 (MISO/AIN1/OC0B/INT0/PCINT1) PB0 (MOSI/AIN0/OC0A/PCINT0) NOTE: Bottom pad should be soldered to ground. DNC: Do Not Connect

8126ES–AVR–07/10 ATtiny13A

1.1 Pin Description

1.1.1 VCC

Supply voltage.

1.1.2 GND

Ground.

1.1.3 Port B (PB5:PB0)

Port B is a 6-bit bi-directional I/O port with inte rnal pull-up resistors (selected for each bit). The Port B output buffers have symmetrical drive characteristics with both high sink and source capability. As inputs, Port B pins that are externally pulled low will source current if the pull-up resistors are activated. The Port B pins are tri-stated when a reset condition becomes active, even if the clock is not running. Port B also serves the functions of various special features of the ATtiny13A as listed on page 55.

1.1.4 RESET

Reset input. A low level on this pin for longer than the minimum pulse length will generate a reset, even if the clock is not running and provided the reset pin has not been disabled. The min- imum pulse length is given in Table 18-4 on page 120 . Shorter pulses are not guaranteed to generate a reset. The reset pin can also be used as a (weak) I/O pin.

8126ES–AVR–07/10 ATtiny13A 2. Overview The ATtiny13A is a low-power CMOS 8-bit microcontroller based on the AVR enhanced RISC architecture. By executing powerfu l instructions in a single cloc k cycle, the ATtiny13A achieves throughputs approaching 1 MIPS per MHz allowing the system designer to optimize power con- sumption versus processing speed.

2.1 Block Diagram

Figure 2-1. Block Diagram PROGRAM COUNTER INTERNAL OSCILLATOR WATCHDOG TIMER STACK POINTER PROGRAM FLASH SRAM MCU CONTROL REGISTER GENERAL PURPOSE REGISTERS INSTRUCTION REGISTER TIMER/ COUNTER0 INSTRUCTION DECODER DATA DIR. REG.PORT B DATA REGISTER PORT B PROGRAMMING LOGIC TIMING AND CONTROL MCU STATUS REGISTER STATUS REGISTER ALU PORT B DRIVERS PB[0:5] VCC GND CONTROL LINES 8-BIT DATABUS Z ADC / ANALOG COMPARATOR INTERRUPT UNIT CALIBRATED Y X RESET CLKI WATCHDOG OSCILLATOR DATA EEPROM

8126ES–AVR–07/10 ATtiny13A The AVR core combines a rich instruction set with 32 general purpose working registers. All 32 registers are directly connected to the Arit hmetic Logic Unit (ALU), allowing two independent registers to be accessed in one single instruction executed in one clock cycle. The resulting architecture is more code efficient while achiev ing throughputs up to ten times faster than con- ventional CISC microcontrollers. The ATtiny13A provides the following features: 1K byte of In-System Programmable Flash, 64 bytes EEPROM, 64 bytes SRAM, 6 ge neral purpose I/O lines, 32 general purpose working reg- isters, one 8-bit Timer/Counter with compare modes, Internal and External Interrupts, a 4- channel, 10-bit ADC, a programmable Watchdog Ti mer with internal Oscillator, and three soft- ware selectable power saving modes. The Idle mode stops the CPU while allowing the SRAM, Timer/Counter, ADC, Analog Comparator, and Interrupt system to continue functioning. The Power-down mode saves the register contents, di sabling all chip functi ons until the next Inter- rupt or Hardware Reset. The ADC Noise Reduction mode stops the CPU and all I/O modules except ADC, to minimize switching noise during ADC conversions. The device is manufactured using Atmel’s high density non-volatile memory technology. The On-chip ISP Flash allows the Program memory to be re-programmed In-System through an SPI serial interface, by a conventional non-volatile memory programmer or by an On-chip boot code running on the AVR core. The ATtiny13A AVR is supported with a full suite of program and syst em development tools including: C Compilers, Macro Assemblers, Program Debugger/Simulators, and Evaluation kits.

8126ES–AVR–07/10 ATtiny13A 3. About

3.1 Resources

A comprehensive set of drivers, application notes, data sheets and descriptions on development tools are available for download at http://www.atmel.com/avr.

3.2 Code Examples

This documentation contains simple code examples that briefly show how to use various parts of the device. These code examples assume that the part specific header file is included before compilation. Be aware that not all C compiler vendors include bit definitions in the header files and interrupt handling in C is compiler dependent. Please confirm with the C compiler documen- tation for more details.

3.3 Data Retention

Reliability Qualification results sh ow that the projected data retention failure rate is much less than 1 PPM over 20 years at 85°C or 100 years at 25°C.

8126ES–AVR–07/10 ATtiny13A 4. Register Summary Address Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Page 0x3F SREG I T H S V N Z C page 9 0x3D SPL SP[7:0] page 11 0x3B GIMSK – INT0 PCIE – – – – – page 47 0x3A GIFR – INTF0 PCIF – – – – – page 48 0x39 TIMSK0 – – – – OCIE0B OCIE0A TOIE0 – page 75 0x38 TIFR0 – – – – OCF0B OCF0A TOV0 – page 76 0x37 SPMCSR – – – CTPB RFLB PGWRT PGERS SELFPR- page 98 0x36 OCR0A Timer/Counter – Output Compare Register A page 75 0x35 MCUCR –P U D S E S M 1 S M 0 – ISC01 ISC00 pages 33, 47, 57 0x34 MCUSR – – – – WDRF BORF EXTRF PORF page 42 0x33 TCCR0B FOC0A FOC0B – – WGM02 CS02 CS01 CS00 page 73 0x32 TCNT0 Timer/Counter (8-bit) page 74 0x31 OSCCAL Oscillator Calibration Register page 27 0x30 BODCR – – – – – – BODS BODSE page 33 0x2F TCCR0A COM0A1 COM0A0 COM0B1 COM0B0 – –W G M 0 1 W G M 0 0 page 70 0x2E DWDR DWDR[7:0] page 97 0x2D Reserved – 0x2C Reserved – 0x2B Reserved – 0x2A Reserved – 0x29 OCR0B Timer/Counter – Output Compare Register B page 75 0x28 GTCCR TSM – – – – – – PSR10 page 78 0x27 Reserved – 0x26 CLKPR CLKPCE – – – CLKPS3 CLKPS2 CLKPS1 CLKPS0 page 28 0x25 PRR – – – – – – PRTIM0 PRADC page 34 0x24 Reserved – 0x23 Reserved – 0x22 Reserved – 0x21 WDTCR WDTIF WDTIE WDP3 WDCE WDE WDP2 WDP1 WDP0 page 42 0x20 Reserved – 0x1F Reserved – 0x1E EEARL – – EEPROM Address Register page 20 0x1D EEDR EEPROM Data Register page 20 0x1C EECR – – EEPM1 EEPM0 EERIE EEMPE EEPE EERE page 21 0x1B Reserved – 0x1A Reserved – 0x19 Reserved – 0x18 PORTB – – PORTB5 PORTB4 PORTB3 PORTB2 PORTB1 PORTB0 page 57 0x17 DDRB – – DDB5 DDB4 DDB3 DDB2 DDB1 DDB0 page 57 0x16 PINB – – PINB5 PINB4 PINB3 PINB2 PINB1 PINB0 page 58 0x15 PCMSK – – PCINT5 PCINT4 PCINT3 PCINT2 PCINT1 PCINT0 page 48 0x14 DIDR0 – – ADC0D ADC2D ADC3D ADC1D AIN1D AIN0D pages 81, 95 0x13 Reserved – 0x12 Reserved – 0x11 Reserved – 0x10 Reserved – 0x0F Reserved – 0x0E Reserved – 0x0D Reserved – 0x0C Reserved – 0x0B Reserved – 0x0A Reserved – 0x09 Reserved – 0x08 ACSR ACD ACBG ACO ACI ACIE – ACIS1 ACIS0 page 80 0x07 ADMUX – REFS0 ADLAR – – – MUX1 MUX0 page 92 0x06 ADCSRA ADEN ADSC ADATE ADIF ADIE ADPS2 ADPS1 ADPS0 page 93 0x05 ADCH ADC Data Register High Byte page 94 0x04 ADCL ADC Data Register Low Byte page 94 0x03 ADCSRB –A C M E – – – ADTS2 ADTS1 ADTS0 pages 80, 95 0x02 Reserved – 0x01 Reserved – 0x00 Reserved –

8126ES–AVR–07/10 ATtiny13A Notes: 1. For compatibility with future devices, reserved bits shou ld be written to zero if accessed. Reserved I/O memory addresses should never be written. 2. I/O Registers within the address range 0x00 - 0x1F are directly bit-accessible using the SBI and CBI instructions. In these registers, the value of single bits can be checked by using the SBIS and SBIC instructions.ome of the Status Flags are cleared by writing a logical one to them. Note that, unlike most other AVRs, the CBI and SBI instructions will only operation the specified bit, and can therefore be used on registers containing such Status Flags. The CBI and SBI instructions work with registers 0x00 to 0x1F only.

8126ES–AVR–07/10 ATtiny13A 5. Instruction Set Summary Mnemonics Operands Description Operation Flags #Clocks ARITHMETIC AND LOGIC INSTRUCTIONS ADD Rd, Rr Add two Registers Rd ← Rd + Rr Z,C,N,V,H 1 ADC Rd, Rr Add with Carry two Registers Rd ← Rd + Rr + C Z,C,N,V,H 1 ADIW Rdl,K Add Immediate to Word Rdh:Rdl ← Rdh:Rdl + K Z,C,N,V,S 2 SUB Rd, Rr Subtract two Registers Rd ← Rd - Rr Z,C,N,V,H 1 SUBI Rd, K Subtract Constant from Register Rd ← Rd - K Z,C,N,V,H 1 SBC Rd, Rr Subtract with Carry two Registers Rd ← Rd - Rr - C Z,C,N,V,H 1 SBCI Rd, K Subtract with Carry Constant from Reg. Rd ← Rd - K - C Z,C,N,V,H 1 SBIW Rdl,K Subtract Immediate from Word Rdh:Rdl ← Rdh:Rdl - K Z,C,N,V,S 2 AND Rd, Rr Logical AND Registers Rd ← Rd • Rr Z,N,V 1 ANDI Rd, K Logical AND Register and Constant Rd ← Rd • K Z,N,V 1 OR Rd, Rr Logical OR Registers Rd ← Rd v Rr Z,N,V 1 ORI Rd, K Logical OR Register and Constant Rd ← Rd v K Z,N,V 1 EOR Rd, Rr Exclusive OR Registers Rd ← Rd ⊕ Rr Z,N,V 1 COM Rd One’s Complement Rd ← 0xFF − Rd Z,C,N,V 1 NEG Rd Two’s Complement Rd ← 0x00 − Rd Z,C,N,V,H 1 SBR Rd,K Set Bit(s) in Register Rd ← Rd v K Z,N,V 1 CBR Rd,K Clear Bit(s) in Register Rd ← Rd • (0xFF - K) Z,N,V 1 INC Rd Increment Rd ← Rd + 1 Z,N,V 1 DEC Rd Decrement Rd ← Rd − 1 Z,N,V 1 TST Rd Test for Zero or Minus Rd ← Rd • Rd Z,N,V 1 CLR Rd Clear Register Rd ← Rd ⊕ Rd Z,N,V 1 SER Rd Set Register Rd ← 0xFF None 1 BRANCH INSTRUCTIONS RJMP k Relative Jump PC ← PC + k + 1 None 2 IJMP Indirect Jump to (Z) PC ← Z None 2 RCALL k Relative Subroutine Call PC ← PC + k + 1 None 3 ICALL Indirect Call to (Z) PC ← ZN o n e 3 RET Subroutine Return PC ← STACK None 4 RETI Interrupt Return PC ← STACK I 4 CPSE Rd,Rr Compare, Skip if Equal if (Rd = Rr) PC ← PC + 2 or 3 None 1/2/3 CP Rd,Rr Compare Rd − Rr Z, N,V,C,H 1 CPC Rd,Rr Compare with Carry Rd − Rr − C Z, N,V,C,H 1 CPI Rd,K Compare Register with Immediate Rd − K Z, N,V,C,H 1 SBRC Rr, b Skip if Bit in Register Cleared if (Rr(b)=0) PC ← PC + 2 or 3 None 1/2/3 SBRS Rr, b Skip if Bit in Register is Set if (Rr(b)=1) PC ← PC + 2 or 3 None 1/2/3 SBIC P, b Skip if Bit in I/O Register Cleared if (P(b)=0) PC ← PC + 2 or 3 None 1/2/3 SBIS P, b Skip if Bit in I/O Register is Set if (P(b)=1) PC ← PC + 2 or 3 None 1/2/3 BRBS s, k Branch if Status Flag Set if (SREG(s) = 1) then PC ←PC+k + 1 None 1/2 BRBC s, k Branch if Status Flag Cleared if (SREG(s) = 0) then PC ←PC+k + 1 None 1/2 BREQ k Branch if Equal if (Z = 1) then PC ← PC + k + 1 None 1/2 BRNE k Branch if Not Equal if (Z = 0) then PC ← PC + k + 1 None 1/2 BRCS k Branch if Carry Set if (C = 1) then PC ← PC + k + 1 None 1/2 BRCC k Branch if Carry Cleared if (C = 0) then PC ← PC + k + 1 None 1/2 BRSH k Branch if Same or Higher if (C = 0) then PC ← PC + k + 1 None 1/2 BRLO k Branch if Lower if (C = 1) then PC ← PC + k + 1 None 1/2 BRMI k Branch if Minus if (N = 1) then PC ← PC + k + 1 None 1/2 BRPL k Branch if Plus if (N = 0) then PC ← PC + k + 1 None 1/2 BRGE k Branch if Greater or Equal, Signed if (N ⊕ V= 0) then PC ← PC + k + 1 None 1/2 BRLT k Branch if Less Than Zero, Signed if (N ⊕ V= 1) then PC ← PC + k + 1 None 1/2 BRHS k Branch if Half Carry Flag Set if (H = 1) then PC ← PC + k + 1 None 1/2 BRHC k Branch if Half Carry Flag Cleared if (H = 0) then PC ← PC + k + 1 None 1/2 BRTS k Branch if T Flag Set if (T = 1) then PC ← PC + k + 1 None 1/2 BRTC k Branch if T Flag Cleared if (T = 0) then PC ← PC + k + 1 None 1/2 BRVS k Branch if Overflow Flag is Set if (V = 1) then PC ← PC + k + 1 None 1/2 BRVC k Branch if Overflow Flag is Cleared if (V = 0) then PC ← PC + k + 1 None 1/2 BRIE k Branch if Interrupt Enabled if ( I = 1) then PC ← PC + k + 1 None 1/2 BRID k Branch if Interrupt Disabled if ( I = 0) then PC ← PC + k + 1 None 1/2 BIT AND BIT-TEST INSTRUCTIONS SBI P,b Set Bit in I/O Register I/O(P,b) ← 1N o n e 2 CBI P,b Clear Bit in I/O Register I/O(P,b) ← 0N o n e 2 LSL Rd Logical Shift Left Rd(n+1) ← Rd(n), Rd(0) ← 0 Z,C,N,V 1 LSR Rd Logical Shift Right Rd(n) ← Rd(n+1), Rd(7) ← 0 Z,C,N,V 1 ROL Rd Rotate Left Through Carry Rd(0) ←C,Rd(n+1)← Rd(n),C←Rd(7) Z,C,N,V 1

8126ES–AVR–07/10 ATtiny13A ROR Rd Rotate Right Through Carry Rd(7) ←C,Rd(n)← Rd(n+1),C←Rd(0) Z,C,N,V 1 ASR Rd Arithmetic Shift Right Rd(n) ← Rd(n+1), n=0..6 Z,C,N,V 1 BSET s Flag Set SREG(s) ← 1 SREG(s) 1 BCLR s Flag Clear SREG(s) ← 0 SREG(s) 1 BST Rr, b Bit Store from Register to T T ← Rr(b) T 1 BLD Rd, b Bit load from T to Register Rd(b) ← TN o n e 1 SEC Set Carry C ← 1C 1 CLC Clear Carry C ← 0 C 1 SEN Set Negative Flag N ← 1N 1 CLN Clear Negative Flag N ← 0 N 1 SEZ Set Zero Flag Z ← 1Z 1 CLZ Clear Zero Flag Z ← 0 Z 1 SEI Global Interrupt Enable I ← 1I 1 CLI Global Interrupt Disable I ← 0 I 1 SES Set Signed Test Flag S ← 1S 1 CLS Clear Signed Test Flag S ← 0 S 1 SEV Set Twos Complement Overflow. V ← 1V 1 CLV Clear Twos Complement Overflow V ← 0 V 1 SET Set T in SREG T ← 1T 1 CLT Clear T in SREG T ← 0 T 1 SEH Set Half Carry Flag in SREG H ← 1H 1 CLH Clear Half Carry Flag in SREG H ← 0 H 1 DATA TRANSFER INSTRUCTIONS MOV Rd, Rr Move Between Registers Rd ← Rr None 1 MOVW Rd, Rr Copy Register Word Rd+1:Rd ← Rr+1:Rr None 1 LDI Rd, K Load Immediate Rd ← KN o n e 1 LD Rd, X Load Indirect Rd ← (X) None 2 LD Rd, X+ Load Indirect and Post-Inc. Rd ← (X), X ← X + 1 None 2 LD Rd, - X Load Indirect and Pre-Dec. X ← X - 1, Rd ← (X) None 2 LD Rd, Y Load Indirect Rd ← (Y) None 2 LD Rd, Y+ Load Indirect and Post-Inc. Rd ← (Y), Y ← Y + 1 None 2 LD Rd, - Y Load Indirect and Pre-Dec. Y ← Y - 1, Rd ← (Y) None 2 LDD Rd,Y+q Load Indirect with Displacement Rd ← (Y + q) None 2 LD Rd, Z Load Indirect Rd ← (Z) None 2 LD Rd, Z+ Load Indirect and Post-Inc. Rd ← (Z), Z ← Z+1 None 2 LD Rd, -Z Load Indirect and Pre-Dec. Z ← Z - 1, Rd ← (Z) None 2 LDD Rd, Z+q Load Indirect with Displacement Rd ← (Z + q) None 2 LDS Rd, k Load Direct from SRAM Rd ← (k) None 2 ST X, Rr Store Indirect (X) ← Rr None 2 ST X+, Rr Store Indirect and Post-Inc. (X) ← Rr, X ← X + 1 None 2 ST - X, Rr Store Indirect and Pre-Dec. X ← X - 1, (X) ← Rr None 2 ST Y, Rr Store Indirect (Y) ← Rr None 2 ST Y+, Rr Store Indirect and Post-Inc. (Y) ← Rr, Y ← Y + 1 None 2 ST - Y, Rr Store Indirect and Pre-Dec. Y ← Y - 1, (Y) ← Rr None 2 STD Y+q,Rr Store Indirect with Displacement (Y + q) ← Rr None 2 ST Z, Rr Store Indirect (Z) ← Rr None 2 ST Z+, Rr Store Indirect and Post-Inc. (Z) ← Rr, Z ← Z + 1 None 2 ST -Z, Rr Store Indirect and Pre-Dec. Z ← Z - 1, (Z) ← Rr None 2 STD Z+q,Rr Store Indirect with Displacement (Z + q) ← Rr None 2 STS k, Rr Store Direct to SRAM (k) ← Rr None 2 LPM Load Program Memory R0 ← (Z) None 3 LPM Rd, Z Load Program Memory Rd ← (Z) None 3 LPM Rd, Z+ Load Program Memory and Post-Inc Rd ← (Z), Z ← Z+1 None 3 SPM Store Program Memory (z) ← R1:R0 None IN Rd, P In Port Rd ← PN o n e 1 OUT P, Rr Out Port P ← Rr None 1 PUSH Rr Push Register on Stack STACK ← Rr None 2 POP Rd Pop Register from Stack Rd ← STACK None 2 MCU CONTROL INSTRUCTIONS NOP No Operation None 1 SLEEP Sleep (see specific descr. for Sleep function) None 1 WDR Watchdog Reset (see specific descr. for WDR/Timer) None 1 BREAK Break For On-chip Debug Only None N/A Mnemonics Operands Description Operation Flags #Clocks

8126ES–AVR–07/10 ATtiny13A 6. Ordering Information Notes: 1. Code indicators: – H or 7: NiPdAu lead finish – U, N or F: matte tin – R: tape & reel 2. All packages are Pb-free, halide-free and fully green and they co mply with the European directive for Restriction of Hazard- ous Substances (RoHS). 3. Topside marking for ATtiny13A: – 1st Line: T13 – 2nd Line: Axx – 3rd Line: xxx 4. These devices can also be supplied in wafer form. Please contact your local Atmel sales office for detailed ordering informa- tion and minimum quantities. 5. For typical and Electrical characteristics for this device please consult Appendix A, ATtiny13A Specification at 105°C. 6. For typical and Electrical characteristics for this device please consult Appendix B, ATtiny13A Specification at 125°C. Speed (MHz) Power Supply (V) Ordering Code (1) Package(2) Operation Range 20 1.8 - 5.5 ATtiny13A-PU ATtiny13A-SU ATtiny13A-SH ATtiny13A-SHR ATtiny13A-SSU ATtiny13A-SSH ATtiny13A-SSHR ATtiny13A-MU ATtiny13A-MUR ATtiny13A-MMU (3) ATtiny13A-MMUR(3) 8P3 8S2 8S2 8S2 8S1 8S1 8S1 20M1 20M1 10M1 (3) 10M1(3) Industrial ATtiny13A-SN ATtiny13A-SNR ATtiny13A-SS7 ATtiny13A-SS7R 8S2 8S2 8S1 8S1 Industrial (-40°C to +105°C) (5) ATtiny13A-SF ATtiny13A-SFR 8S2 8S2 Industrial (-40°C to +125°C) (6) Package Type 8P3 8-lead, 0.300" Wide, Plastic Dual Inline Package (PDIP) 8S2 8-lead, 0.209" Wide, Plastic Small Outline Package (EIAJ SOIC) 8S1 8-lead, 0.150" Wide, Plastic Gull-Wing Small Outline (JEDEC SOIC) 20M1 20-pad, 4 x 4 x 0.8 mm Body, Lead Pitch 0.50 mm, Micro Lead Frame Package (MLF) 10M1 10-pad, 3 x 3 x 1 mm Body, Lead Pitch 0.50 mm, Micro Lead Frame Package (MLF)

8126ES–AVR–07/10 ATtiny13A 7. Packaging Information 7.1 8P3

2325 Orchard Parkway

San Jose, CA 95131 TITLE DRAWING NO. R REV. 8P3, 8-lead, 0.300" Wide Body, Plastic Dual In-line Package (PDIP) 01/09/02 8P3 B D E e Lb2 b A2 A N eA c

4 PLCS

(Unit of Measure = inches) SYMBOL MIN NOM MAX NOTE Notes: 1. This drawing is for general information only; refer to JEDEC Drawing MS-001, Variation BA for additional information. 2. Dimensions A and L are measured with the package seated in JEDEC seating plane Gauge GS-3. 3. D, D1 and E1 dimensions do not include mold Flash or protrusions. Mold Flash or protrusions shall not exceed 0.010 inch. 4. E and eA measured with the leads constrained to be perpendicular to datum. 5. Pointed or rounded lead tips are preferred to ease insertion. A 0.210 2 A2 0.115 0.130 0.195 b 0.014 0.018 0.022 5 b2 0.045 0.060 0.070 6 b3 0.030 0.039 0.045 6 c 0.008 0.010 0.014 D 0.355 0.365 0.400 3 D1 0.005 3 E 0.300 0.310 0.325 4 E1 0.240 0.250 0.280 3 e 0.100 BSC eA 0.300 BSC 4 L 0.115 0.130 0.150 2

8126ES–AVR–07/10 ATtiny13A 7.2 8S2 TITLE DRAWING NO. GPC REV. Package Drawing Contact: packagedrawings@atmel.com 8S2STN F 8S2, 8-lead, 0.208” Body, Plastic Small Outline Package (EIAJ) 4/15/08 COMMON DIMENSIONS (Unit of Measure = mm) SYMBOL MIN NOM MAX NOTE Notes: 1. This drawing is for general information only; refer to EIAJ Drawing EDR-7320 for additional information. 2. Mismatch of the upper and lower dies and resin burrs aren't included. 3. Determines the true geometric position. A 1.70 2.16 A1 0.05 0.25 b 0.35 0.48 4 C 0.15 0.35 4 D 5.13 5.35 E1 5.18 5.40 2 E 7.70 8.26 L 0.51 0.85 θ 0° 8° e 1.27 BSC 3 θθ NN EE TOP VIEWTOP VIEW CC E1E1 END VIEWEND VIEW AA bb LL A1A1 ee DD SIDE VIEWSIDE VIEW

8126ES–AVR–07/10 ATtiny13A 7.3 8S1 San Jose, CA 95131 TITLE DRAWING NO. R REV. Note: 10/10/01 8S1, 8-lead (0.150" Wide Body), Plastic Gull Wing Small Outline (JEDEC SOIC) 8S1 A H N Top View C E End View A B L e D Side View COMMON DIMENSIONS (Unit of Measure = mm) SYMBOL MIN NOM MAX NOTE This drawing is for general information only. Refer to JEDEC Drawing MS-012 for proper dimensions, tolerances, datums, etc. A – – 1.75 B – – 0.51 C – – 0.25 D – – 5.00 E – – 4.00 e 1.27 BSC H – – 6.20 L – – 1.27

8126ES–AVR–07/10 ATtiny13A 7.4 20M1 San Jose, CA 95131 TITLE DRAWING NO. R REV. 20M1, 20-pad, 4 x 4 x 0.8 mm Body, Lead Pitch 0.50 mm, A20M1 10/27/04 2.6 mm Exposed Pad, Micro Lead Frame Package (MLF) A 0.70 0.75 0.80 A1 – 0.01 0.05 A2 0.20 REF b 0.18 0.23 0.30 D 4.00 BSC D2 2.45 2.60 2.75 E 4.00 BSC E2 2.45 2.60 2.75 e 0.50 BSC L 0.35 0.40 0.55 SIDE VIEW Pin 1 ID Pin #1 Notch (0.20 R) BOTTOM VIEW TOP VIEW Note: Reference JEDEC Standard MO-220, Fig. 1 (SAW Singulation) WGGD-5. COMMON DIMENSIONS (Unit of Measure = mm) SYMBOL MIN NOM MAX NOTE D E e A 0.08 C L b

8126ES–AVR–07/10 ATtiny13A 7.5 10M1 San Jose, CA 95131 TITLE DRAWING NO. R REV. 10M1, 10-pad, 3 x 3 x 1.0 mm Body, Lead Pitch 0.50 mm, 1.64 x 2.60 mm Exposed Pad, Micro Lead Frame Package A10M1 7/7/06 COMMON DIMENSIONS (Unit of Measure = mm) SYMBOL MIN NOM MAX NOTE A 0.80 0.90 1.00 A1 0.00 0.02 0.05 b 0.18 0.25 0.30 D 2.90 3.00 3.10 D1 1.40 – 1.75 E 2.90 3.00 3.10 E1 2.20 – 2.70 e 0.50 L 0.30 – 0.50 y – – 0.08 K 0.20 – – Pin 1 ID TOP VIEW D E A SIDE VIEW BOTTOM VIEW L b e K Notes: 1. This package conforms to JEDEC reference MO-229C, Variation VEED-5. 2. The terminal #1 ID is a Lasser-marked Feature. y

8126ES–AVR–07/10 ATtiny13A 8. Errata The revision letters in this section refer to the revision of the ATtiny13A device. 8.1 ATtiny13A Rev. G – H

• EEPROM can not be written below 1.9 Volt 1. EEPROM can not be written below 1.9 Volt Writing the EEPROM at VCC below 1.9 volts might fail. Problem Fix/Workaround Do not write the EEPROM when VCC is below 1.9 volts. 8.2 ATtiny13A Rev. E – F These device revisions were not sampled. 8.3 ATtiny13 Rev. A – D These device revisions were referred to as ATtiny13/ATtiny13V.

8126ES–AVR–07/10 ATtiny13A 9. Datasheet Revision History Please note that page numbers in this section refe r to the current version of this document and may not apply to previous versions. 9.1 Rev. 8126E – 07/10 1. Updated description in Section 6.4.2 “CLKPR – Clock Prescale Register” on page 28. 2. Adjusted notes in Table 18-1, “DC Characteristics, TA = -40°C to +85°C,” on page 117. 3. Updated plot order in Section 19. “Typical Characteristics” on page 124, added some plots, also some headers and figure titles adjusted. 4. Updated Section 6. “Ordering Information” on page 11, added extended temperature part numbers, as well tape & reel part numbers. Notes adjusted. 5. Updated bit syntax throughout the data sheet, e.g. from CS02:0 to CS0[2:0]. 9.2 Rev. 8126D – 11/09 1. Added note “If the RSTDISPL fuse is programmed...” in Startup-up Times Table 6-5 and Table 6-6 on page 26. 2. Added addresses in all Register Description tables and cross-references to Register Summary. 3. Updated naming convention for -COM bits in tables from Table 11-2 on page 70 to Table 11-7 on page 72. 4. Updated value for tWD_ERASE in Table 17-8, “Minimum Wait Delay Before Writing the Next Flash or EEPROM Location,” on page 108. 5. Added NiPdAU note for -SH and -SSH in Section 6. “Ordering Information” on page 11. 9.3 Rev. 8126C – 09/09 1. Added EEPROM errata for rev. G - H on page 17. 2. Added a note about topside marking in Section 6. “Ordering Information” on page 11. 9.4 Rev. 8126B – 11/08 1. Updated order codes on page 11 to reflect changes in material composition. 2. Updated sections: – “DIDR0 – Digital Input Disable Register 0” on page 81 – “DIDR0 – Digital Input Disable Register 0” on page 95 3. Updated “Register Summary” on page 7. 9.5 Rev. 8126A – 05/08 1. Initial revision, created from document 2535I – 04/08. 2. Updated characterist ic plots of section “Typical Characteristics” , starting on page 124. 3. Updated “Ordering Information” on page 11. 4. Updated section: – “Speed” on page 118 5. Update tables: – “DC Characteristics, TA = -40°C to +85°C” on page 117 – “Calibration Accuracy of Internal RC Oscillator” on page 119

8126ES–AVR–07/10 ATtiny13A – “Reset, Brown-out, and Internal Voltage Characteristics” on page 120 – “ADC Characteristics, Single Ended Channels. TA = -40°C to +85°C” on page 121 – “Serial Programming Characteristics, TA = -40°C to +85°C” on page 122 6. Added description of new function, “Power Reduction Register”: – Added functional description on page 31 – Added bit description on page 34 – Added section “Supply Current of I/O Modules” on page 124 – Updated Register Summary on page 7 7. Added description of new function, “Software BOD Disable”: – Added functional description on page 31 – Updated section on page 32 – Added register description on page 33 – Updated Register Summary on page 7 8. Added description of enhanced function, “Enhanced Power-On Reset”: – Updated Table 18-4 on page 120, and Table 18-5 on page 120

8126ES–AVR–07/10 © 2010 Atmel Corporation. All rights reserved. Atmel ®, logo and combinations thereof, AVR ® and others are registered trademarks or trade- marks of Atmel Corporation or its subsidiaries. Other terms and product names may be trademarks of others. Headquarters International Atmel Corporation San Jose, CA 95131 USA Tel: 1(408) 441-0311 Fax: 1(408) 487-2600 Atmel Asia Unit 1-5 & 16, 19/F BEA Tower, Millennium City 5

418 Kwun Tong Road

Kwun Tong, Kowloon Hong Kong Tel: (852) 2245-6100 Fax: (852) 2722-1369 Atmel Europe Le Krebs 8, Rue Jean-Pierre Timbaud BP 309

78054 Saint-Quentin-en-

9F, Tonetsu Shinkawa Bldg. 1-24-8 Shinkawa Chuo-ku, Tokyo 104-0033 Japan Tel: (81) 3-3523-3551 Fax: (81) 3-3523-7581 Product Contact Web Site www.atmel.com Technical Support avr@atmel.com Sales Contact www.atmel.com/contacts Literature Requests www.atmel.com/literature Disclaimer: The information in this document is provided in connection wi th Atmel products. No license, expr ess or implied, by estoppel or otherwise, to any intellectual property right is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN ATMEL’S TERMS AND CONDI- TIONS OF SALE LOCATED ON ATMEL’S WEB SITE, ATMEL ASSUMES NO LI ABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTOR Y WARRANTY RELATING TO ITS PRODUCTS INCLUDING , BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICU LAR PURPOSE, OR NON-INFRINGEMENT. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRE CT, CONSEQUENTIAL, PUNITIVE, SPECIAL OR I NCIDEN- TAL DAMAGES (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF PROFITS, BUSINESS INTERRUPTION, OR LOSS OF INFORMATION) ARISING OUT OF THE USE OR INABILITY TO USE THIS DOCUMENT, EVEN IF ATMEL HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Atmel makes no representations or warranties with respect to the accuracy or comp leteness of the contents of th is document and reserves the rig ht to make changes to specifications and product descriptions at any time without notice. Atmel does not make any commitment to update the information contained her ein. Unless specifically provided otherwise, Atmel products are not suitable for, and shall not be used in, automotive applications. Atmel’s products are not int ended, authorized, or warranted for use as components in applications intended to support or sustain life.