ATM0350D17

DATASHEET SEARCH SITE | WWW.ALLDATASHEET.COM

Document overview

• Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
• PDF pages: 21

Technical content

※ PART NO. : ATM0350D17 (AZ DISPLAYS) V1.0 APPROVAL COMPANY CHOP CUSTOMER COMMENTS AZ DISPLAYS ENGINEERING APPROVAL DESIGN BY CHECKED BY APPROVED BY GZC ZZK GuZH

ATM0350D17(AZ DISPLAYS) TFT MODULE V1.0 AZ DISPLAYS REVISION RECORD REVISION REVISION DATE PAGE CONTENTS V1.0 2019-08-29 FIRST ISSUE

ATM0350D17(AZ DISPLAYS) TFT MODULE V1.0 AZ DISPLAYS ※ CONTENTS 1. GENERAL SPECIFICATIONS 2. PIN ASSIGNMENT 3. OPERATING SPECIFICATIONS 4. OPTICAL SPECIFICATIONS 5. RELIABILITY TEST 6. PRECAUTION FOR USING LCM 7. MECHANICAL DRAWING 8. PACKAGE DRAWING 9. INSPECTION SPECIFICATION

ATM0350D17(AZ DISPLAYS) TFT MODULE V1.0 AZ DISPLAYS 1. GENERAL SPECIFICATIONS Item Specification Remark 1. LCD size 3.5 inch(Diagonal) 2. Driver element a-Si TFT active matrix 3. Resolution 320x(RGB)x240 4. Display mode Normally Black, IPS, Transmissive 5. Dot Pitch (W*H) 0.073mm(W) x 0.219mm(H) 6. Pixel pitch(W*H) 0.219mm(W) x 0.219mm(H) 7. Active Area(W*H) 70.08mm(W) x 52.56mm(H) 8. Module size (W*H) 76.9mm(W) x 63.9mm(H) x 3.3mm(D) Note 1 9. Surface treatment Anti-glare 10. Color arrangement RGB-stripe 11. Color 16.7M 12. Viewing angle (L/R/T/B) 80/80/80/80 13. Interface 24bit RGB interface 14. LCD controller N.A. 15. LCM Brightness 500 cd/m2 Typ. 16. Backlight driving condition 20mA @18.6V 17. Touch panel N.A. 18. Touch controller N.A.

19 Operation Temperature -30~80 ºC

1. Weight 30g Typ. 21. RoHS RoHS compliant Note 1: Please refer to mechanical drawing.

ATM0350D17(AZ DISPLAYS) TFT MODULE V1.0 AZ DISPLAYS 2. PIN ASSIGNMENT TFT LCD Panel Driving Section FPC Connector is used for the module electronics interface. The recommended model is “6240" series manufactured by Kyocera elco. Pin No. Symbol Function Level Note 1-2 LED- Power for LED backlight(Cathode) P 3-4 LED+ Power for LED backlight(Anode) P 5-6 NC No connection -- 7 /RESET Hardware reset I 8 /CS SPI Interface chip select bar I

9 SCK SPI interface data clock I

10 SDI SPI interface data input I

11 NC No connection O

12~19 B0~B7 Blue data I 20~27 G0~G7 Green data I 28~35 R0-R7 Red data I

36 HSYNC Horizontal sync input I

37 VSYNC Vertical sync input I

38 DCLK Dot data clock I

39-40 VDDIO Power supply for I/O logic P 41-42 VDD Power supply for internal logic P

43 NC No connection P

44 NC No connection --

45 NC/YU No connection, reserved for TP --

46 NC/XR No connection, reserved for TP --

47 NC/YD No connection, reserved for TP --

48 NC/XL No connection, reserved for TP --

52 DE Data enable input I

I: input, O: output, P: Power

ATM0350D17(AZ DISPLAYS) TFT MODULE V1.0 AZ DISPLAYS 3. Operating Specification

3.1.1 ABSOLUTE MAXIMUM RATINGS

Min. Max. Power Voltage VDD -0.3 5.0 V Operation Temperature TOP -30 80 ºC Storage Temperature TST -30 80 ºC LED Reverse Voltage VR - 1 . 2 V Each LED Note 2 LED Forward Current IF 25 mA Each LED Note 1: The absolute maximum rating values of this product are not allowed to be exceeded at any times. Should a module be used with any of the absolute maximum ratings exceeded, the characteristics of the module may not be recovered, or in an extreme case, the module may be permanently destroyed. Note 2: VR Conditions: Zener Diode 20mA

3.1.2 Typical Operation Conditions

Min. Typ. Max. Power Voltage VDD 3.0 3.3 3.6 V Note 1 IO Power Voltage VDDIO 3.0 -- 3.6 Input Logic High Voltage VIH 0.8VDDIO -- VDDIO V Note 2 Input Logic Low Voltage VIL 0 -- 0.2VDDIO V Note 2 Note 1: VDDIO setting should match the signals output voltage of customer’s system board. Note 2: DCLK,HS,VS,RESET,DE,R0~R7,G0~G7,B0~B7.

3.1.3 Backlight driving conditions

Min. Typ. Max. Voltage for LED Backlight VL 17.4 18.6 19.8 V Note 1 Current for LED Backlight IL -- 20 -- mA LED life time -- 30000 -- -- Hr Note 2 Note 1: The LED Supply Voltage is defined by the number of LED at Ta=25 ℃ and IL =20mA. Note 2: The “LED life time” is defined as the module brightness decrease to 50% original brightness at Ta=25 ℃ and IL =20mA.

ATM0350D17(AZ DISPLAYS) TFT MODULE V1.0 AZ DISPLAYS

3.2 Timing Characteristics

3.2.1 SYNC Mode

ATM0350D17(AZ DISPLAYS) TFT MODULE V1.0 AZ DISPLAYS

3.2.2 SYNC-DE Mode

ATM0350D17(AZ DISPLAYS) TFT MODULE V1.0 AZ DISPLAYS

3.2.2 DE Mode

NOTE:“Input ”means these signals are driven by host side.

ATM0350D17(AZ DISPLAYS) TFT MODULE V1.0 AZ DISPLAYS

3.3 Timing Diagram

Parallel 24-bit RGB Input Timing(PVDD=VDD=VDDIO=3.3V,AGND=0V,TA=25℃) Serial 8-bit RGB Input Timing(PVDD=VDD=VDDIO=3.3V,AGND=0V,TA=25℃) NOTE: It is necessary to keep Tvbp=12 and Thbp= 43 in sync mode.DE mode is unnecessary to keep it.

ATM0350D17(AZ DISPLAYS) TFT MODULE V1.0 AZ DISPLAYS

4.0 OPTICAL SPECIFICATIONS

Min. Typ. Max. Viewing Angle (CR≥10) θL Φ=180 o(9 O'CLOCK) 70 80 -- degree Note 1 θR Φ = 0 o(3 O'CLOCK) 70 80 -- θT Φ = 9 0 o(12 O'CLOCK) 70 80 -- θB Φ=270 o(6 O'CLOCK) 70 80 -- Response Time TON + TOFF Normal Θ=Φ=0o -- 30 40 msec Note 3 Contrast Ratio CR 640 800 -- -- Note 4 Color Chromaticity WX 0.26 0.31 0.36 -- Note 2 Note 5 Note 6 WY 0.26 0.31 0.36 -- Luminance L 400 500 -- cd/m 2 Note 6 Luminance Uniformity YU 70 80 -- % Note 7 Test Conditions: 1. IL=20mA (Backlight current), the ambient temperature is 25℃. 2. The test systems refer to Note 2. Note 1: Definition of viewing angle range Figure 4.1 Definition of viewing angle.

ATM0350D17(AZ DISPLAYS) TFT MODULE V1.0 AZ DISPLAYS Note 4: Definition of contrast ratio Note 5: Definition of color chromaticity (CIE1931) Color coordinates measured at center point of LCD. Note 6: All input terminals LCD panel must be ground while measuring the center area of the panel. Note 7: Definition of Luminance Uniformity Active area is divided into 9 measuring areas (Refer to Fig. 4-4 ).Every measuring point is placed at the center of each measuring area. Figure 4.3 Definition of measuring points. Bmax: The measured maximum luminance of all measurement position. Bmin: The measured minimum luminance of all measurement position.

ATM0350D17(AZ DISPLAYS) TFT MODULE V1.0 AZ DISPLAYS 5. RELIABILITY TEST Item T est Condition Item Remark High temperature storage Ta= 80 ºC 240hrs Note 1 Note 4 Low temperature storage Ta=-30 ºC 240hrs Note 1 Note 4 High temperature operation Ts= 80 ºC 240hrs Note 2 Note 4 Low temperature operation Ts=-30 ºC 240hrs Note 1 Note 4 High temperature/High humidity operation 90% RH 60ºC 240hrs Note 4 Thermal Shock -30℃/30 min ~ +80℃/30 min for a total 100 cycles, Start with cold temperature and end with high temperature. Note 4 Vibration test Freq:10~55~10Hz Amplitude:1.5mm 2 hours for each direction of X,Y,Z (6 hours for total) Mechanical shock 100G 6ms,±X, ±Y, ±Z 3 times for each direction Package vibration test Random Vibration : 0.015G*G/Hz from 5-200HZ, -6dB/Octave from 200-500HZ 2 hours for each direction of X. Y. Z. (6 hours for total) Package drop test Height:60 cm 1 corner, 3 edges, 6 surfaces Electro static discharge ± 2KV, Human Body Mode, 100pF/1500Ω Note 1: Ta is the ambient temperature of samples. Note 2: Ts is the temperature of panel’s surface. Note 3: In the standard condition, there shall be no practical problem that may affect the display function. After the reliability test, the product only guarantees operation, but don’t guarantee all of the cosmetic specification. Note 4: Before cosmetic and function test, the product must have enough recovery time, at least 2 hours at room temperature.

ATM0350D17(AZ DISPLAYS) TFT MODULE V1.0 AZ DISPLAYS 6. PRECAUTION FOR USING LCM 1. When design the product with this LCD Module, make sure the viewing angle matches to its purpose of usage. 2. As LCD panel is made of glass substrate, Dropping the LCD mo dule or banging it against hard objects may cause cracking or fragmentation. Especially at corners and edges. 3. Although the polarizer of thi s LCD Module has the anti-glare coating, always be careful not to scratch its surface. Use of a plastic cover is recommended to protect the surface of polarizer. 4. If the LCD module is stored at below specified temperature, the LC material may freeze and be deteriorated. If it is stored at above specified temperature, the molecular orientation of the LC material may change to Liquid state and it may not revert to its original state. Excessive temperature and humidity could cause polarizer peel off or bubble. Therefore, the LCD module should always be stored within specified temperature range. 5. Saliva or water droplets must be wiped off immediately as th ose may leave stains or cause color changes if remained for a long time. Water vapor will cause corrosion of ITO electrodes. 6. If the surface of LCD panel needs to be cleaned, wipe it swi ftly with cotton or other soft cloth. If it is not still clean enough, blow a breath on the surface and wipe again. 7. The module should be driven according to the specified ratin gs to avoid malfunction and permanent damage. Applying DC voltage cause a rapid deterioration of LC material. Make sure to apply alternating waveform by continuous application of the M signal. Especially the power ON/OFF sequence should be kept to avoid latch-up of driver LSIs and DC charge up to LCD panel. 8. Mechanical Considerations a) LCM are assembled and adjusted with a high degree of precisi on. Avoid excessive shocks and do not make any alterations or modifications. The following should be noted. b) Do not tamper in any way with the tabs on the metal frame. c) Do not modify the PCB by drilli ng extra holes, changing its outline, moving its components or modifying its pattern. d) Do not touch the elastomer connector; especially insert a ba cklight panel (for example, EL). e) When mounting a LCM makes sure that the PCB is not under any stress such as bending or twisting. Elastomer contacts are very delicate and missing pixels could result from slight dislocation of any of the elements. f) Avoid pressing on the metal bezel, otherwise the elastomer c onnector could be deformed and lose contact, resulting in missing pixels. 9. Static Electricity a) Operator Wear the electrostatics shielded clothes because human body may be statically charged if not ware shielded clothes. Never touch any of the conductive parts such as the LSI pads; the copper leads on the PCB and the interface terminals with any parts of the human body. b) Equipment There is a possibility that the static electricity is charged to the equipment, which has a function of peeling or friction action (ex: conveyer, soldering iron, working table). Earth the equipment through proper resistance (electrostatic earth: 1x108 ohm). Only properly grounded soldering irons should be used. If an electric screwdriver is used, it should be well grounded and shielded from commutator sparks. The normal static prevention measures should be observed for work clothes and working benches; for the latter conductive (rubber) mat is recommended. c) Floor Floor is the important part to drain static electricity, which is generated by operators or equipment. There is a possibility that charged static electricity is not properly drained in case of insulating floor. Set the electrostatic earth (electrostatic earth: 1x108 ohm). d) Humidity Proper humidity helps in reducing the chance of generating electrostatic charges. Humidity should be kept over 50%RH. e) Transportation/storage The storage materials also need to be anti-static treated because there is a possibility that the human body or storage materials such as containers may be statically charged by friction or peeling. The modules should be kept in antistatic bags or other containers resistant to static for storage. f) Soldering Solder only to the I/O terminals. Use only soldering irons with proper grounding and no leakage. Soldering temperature : 280°C ± 10°C Soldering time: 3 to 4 sec. Use eutectic solder with resin flux fill. If flux is used, the LCD surface should be covered to avoid flux spatters. Flux residue should be removed afterwards.

ATM0350D17(AZ DISPLAYS) TFT MODULE V1.0 AZ DISPLAYS g) Others The laminator (protective film) is attached on the surface of LCD panel to prevent it from scratches or stains. It should be peeled off slowly using static eliminator. Static eliminator should also be installed to the workbench to prevent LCD module from static charge. 10. Operation a) Driving voltage should be kept within specified range; exces s voltage shortens display life. b) Response time increases with decrease in temperature. c) Display may turn black or dark blue at temperatures above it s operational range; this is (however not pressing on the viewing area) may cause the segments to appear “fractured”. d) Mechanical disturbance during operation (such as pressing on the viewing area) may cause the segments to appear “fractured”. 11. If any fluid leaks out of a damaged glass cell, wash off any human part that comes into contact with soap and water. The toxicity is extremely low but caution should be exercised at all the time. 12. Disassembling the LCD module can cause permanent damage and it should be strictly avoided. 13. LCD retains the display pattern when it is applied for long time (Image retention). To prevent image retention, do not apply the fixed pattern for a long time. Image retention is not a deterioration of LCD. It will be removed after display pattern is changed. 14. Do not use any materials, which emit gas from epoxy resin (hardener for amine) and silicone adhesive agent (dealcohol or deoxym) to prevent discoloration of polarizer due to gas. 15. Avoid the exposure of the module to the direct sunlight or strong ultraviolet light for a long time. The brightness of LCD module may be affected by the routing of CCFL cables due to leakage to the chassis through coupling effect. The inverter circuit needs to be designed taking the level of leakage current into consideration. Thorough evaluation is needed for LCD module and inverter built into its host equipment to ensure specified brig htness.

ATM0350D17(AZ DISPLAYS) TFT MODULE V1.0 AZ DISPLAYS 7. MECHANICAL DRAWING NOTES: 1.Dimensions marked with"()"are for reference. 2.General tolerance:±0.2 mm XL YD XR YU FPC0350D15-2 K1K2A1A2 27.5±0.1 W=0.35±0.05 3.5±0.3 77.0±0.2 64.0±0.2 73.20（BZ OPEN） 55.70（BZ OPEN） 70.08（LCD AA） 52.56(LCD AA) （38.46） （29.46） Displays Centre 1.88 （3.45） 6.43 （8.21） pull tape 44.09±0.8 15.59±0.5 4.50±0.5 MAX 1.50 0.30±0.05 6.50 1.75 24.00 X:0,Y:0 X:320,Y:240 3.30±0.2 Front Rear (6.00) (6.00) Label A K Resolution：320（RGB）*240 component Kapoton Tape component conductorstiffener component BL circuit Single layer Single layer 2-R0.50 154 1 54

ATM0350D17(AZ DISPLAYS) TFT MODULE V1.0 AZ DISPLAYS 8. PACKAGE DRAWING ITEM: QTY: C/T NO: DATE: Label Top paper plate EPE fixer LCM in ESD bag Bottom paper plate Carton Corrugated bar Carton size 44x33x18 cm Quantity per carton 250 pcs

ATM0350D17(AZ DISPLAYS) TFT MODULE V1.0 AZ DISPLAYS 9. INSPECTION SPECIFICATION 1. SCOPE SPECIFICATIONS CONTAIN

1.1 DISPLAY QUALITY EVALUATION

1.2 MECHANICS SPECIFICATION

1. SAMPLING PLAN UNLESS THERE IS OTHER AGREEMENT, THE SAMPLING PLAN FOR INCOMING INSPECTION SHALL FOLLOW MIL-STD-105E. 2.1 LOT SIZE: QUANTITY PER SHIPMENT AS ONE LOT (DIFFERENT MODEL AS DIFFERENT LOT ). 2.2 SAMPLING TYPE: NORMAL INSPECTION, SINGLE SAMPLING. 2.3 SAMPLING LEVEL: LEVEL II.

2.4 AQL: ACCEPTABLE QUALITY LEVEL

MAJOR DEFECT: AQL=0.65 MINOR DEFECT: AQL=1.0 3. PANEL INSPECTION CONDITION

3.1 ENVIRONMENT:

ROOM TEMPERATURE: 25±5°C. HUMIDITY: 65±5% RH. ILLUMINATION: 300 ~ 700 LUX.

3.2 INSPECTION DISTANCE:

35±5 CM

3.3 INSPECTION ANGLE:

THE VISION OF INSPECTOR SHOULD BE PERPENDICULAR TO THE SURFACE OF THE MODULE.

3.4 INSPECTION TIME：

PERCEPTIBILITY TEST TIME: 20 SECONDS MAX. 4. DISPLAY QUALITY

4.1 FUNCTION RELATED:

THE FUNCTION DEFECTS OF LINE DEFECT, ABNORMAL DISPLAY, AND NO DISPLAY ARE CONSIDERED MAJOR DEFECTS.

4.2 BRIGHT/DARK DOTS:

Note: 1: The definition of dot: The size of a defective dot over 1/2 of whole dot is regarded as one defective dot. Bright dot: Dots appear bright and unchanged in size in which LCD panel is displaying under black pattern. The bright dot defect must be visible through 2% ND filter Dark dot: Dots appear dark and unchanged in size in which LCD panel is displaying under pure red, green, blue pattern.

4.3 Pixel Definition:

Note 1: If pixel or partial sub-pixel defects exceed 50% of the affected pixel or sub-pixel area, it shall be considered as1 defect. Note 2: There should be no distinct non-uniformity visible through 2% ND Filter within 2 sec inspection times.

ATM0350D17(AZ DISPLAYS) TFT MODULE V1.0 AZ DISPLAYS 4.4Visual Inspection specifications:

ATM0350D17(AZ DISPLAYS) TFT MODULE V1.0 AZ DISPLAYS Note: Extraneous substance and scratch not affecting the display of image, for instance, extraneous substance under polarizer film but outside the display area, or scratch on metal bezel and backlight module or polarizer film outside the display area, shall not be considered as defective or non-conforming.