ATA5575M2 ATMEL | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 26

Technical content

Features

  • Contactless power supply
  • Contactless read/write data transmission
  • Radio frequency fRF from 100kHz to 150kHz
  • 128-bit EEPROM user memory: 16 Bytes (8 Bits each)
  • 8-bit configuration memory
  • High Q-antenna tolerance due to built-in options
  • Applications
  • Animal ID, waste management, industrial identification
  • ISO/IEC 11784/785 compatibility
  • FDX-A
  • FDX-B
  • On-chip trimmed antenna capacitor
  • 330pF ±3%
  • 250pF ±3%
  • Mega pads 200µm x 400µm
  • Mega pads 200µm x 400µm with 25µm gold bumps for direct coil bonding
  • Other options:
  • Direct access mode
  • OTP functionality ATA5575M2 Read/Write LF RFID IDIC 100kHz to 150kHz DATASHEET

3ATA5575M2 [DATASHEET] 9217F–RFID–12/14 4. Analog Front End (AFE) The AFE includes all circuits which are connected directly to the coil terminals. The AFE generates the IC power supply and handles bi-directional data communication with the reader. The AFE consists of the following blocks:

  • Rectifier to generate a DC supply voltage from the AC coil voltage
  • Clock extractor
  • Switchable load between Coil 1 and Coil 2 for data transmission from tag to the reader
  • Field-gap detector for data transmission from the base station to the tag
  • ESD protection circuitry

4.1 Data Rate Generator

The data rate of the Atmel ATA5575M2 is programmable to operate at RF/50 (FDX-A mode) and RF/32 (FDX-B mode).

4.2 Write Decoder

The write decoder detects the write gaps and verifies the validity of the data stream according to the Atmel® downlink protocol (pulse-interval encoding).

4.3 HV Generator

This on-chip charge pump circuit generates the high voltage required for programming the EEPROM.

4.4 DC Supply

Power is supplied externally to the IDIC via the two coil connections. The IC rectifies and regulates this RF source and uses it to generate its supply voltage.

4.5 Power-On Reset (POR)

The power-on reset circuit blocks the voltage supply to the IDIC until an acceptable voltage threshold has been reached. This, in turn, triggers the default initialization delay sequence. During this configuration period of 98 field clocks, the ATA5575M2 is initialized with the configuration data stored in EEPROM byte 16.

4.6 Clock Extraction

The clock extraction circuit uses the external RF signal as its internal clock source.

4.7 Controller

The control logic module executes the following functions:

  • Load mode register with configuration data from EEPROM byte 16 after power-on and during reading
  • Controls each EEPROM memory read/write access and handles data protection
  • Handle downlink command decoding, detecting protocol violations and error conditions

ATA5575M2 [DATASHEET] 9217F–RFID–12/14

4.8 Mode Register

The mode register maintains a readable shadow copy of the configuration data held in byte 16 of the EEPROM. It is continually refreshed during read mode and (re-)loaded after every POR event or reset command. Depending on the version, upon leaving the Atmel® factory site, the configuration data is pre-programmed according to Table 10-1 on page 18 and Table 10-4 on page 20.

4.9 Modulator

The modulator encodes the serialized EEPROM data for transmission to a tag reader or base station. Two types of encoding are implemented: Differential Biphase and FSK.

4.10 Memory

The memory is a 136-bit EEPROM arranged in 17 bytes of 8 bits each. Programming takes place on a byte basis meaning a complete byte is programmed with a single command. Byte 16 contains the mode/configuration data which is otherwise not transmitted during regular-read operations. A special combination of bits in byte 16 (see Table 5-1 on page 5) locks the whole memory. Once locked, the memory (including byte 16 itself) is not reprogrammable through the RF field again. Figure 4-1. Memory Map Configuration data Byte 16 User data Byte 15 User data Byte 14 User data Byte 13 User data Byte 12 User data Byte 11 User data Byte 10 User data Byte 9 User data Byte 8 User data Byte 7 User data Byte 6 User data Byte 5 User data Byte 4 User data Byte 3 User data Byte 2 User data Byte 1 User data Byte 0 8 bits Not transmitted

5ATA5575M2 [DATASHEET] 9217F–RFID–12/14 5. Operating the Atmel ATA5575M2

5.1 Configuration

The Atmel® ATA5575M2 is mainly designed for ISO11784/11785 applications. It supports FDX-A and FDX-B mode (see also Figure 7-1 on page 14 for the structure of a FDX-B telegram typically used for animal ID applications). The configuration register, byte 16, enables the customer to configure the chip according to the individual application. In delivery state the default configuration is memory reprogrammable, read user data in diff. biphase RF/32 and ID length 128 bit which leads to the byte value '00001001b'.

5.1.1 Lock-bits

The lock bits of the Configuration register are the bits 1 to 5 of the configuration byte and are able to prevent the whole memory of the Atmel ATA5575M2 from reprogramming. As long as the lock bits are set to '00000b' the memory is alterable and the device can be programmed by the customer. In this case the Atmel ATA5575M2 sends out dummy data (all digits set to '0' in the programmed modulation scheme; see Section 5.3.3 “Dummy Data” on page 7) after Reset. If the lock bits are set to '00001b' the memory is still alterable but in difference to the first option the Atmel ATA5575M2 sends out the programmed user data in the modulation scheme defined with bit 7. By setting the lock bits to '01101b' the whole memory is locked and cannot be altered. After Reset the Atmel ATA5575M2 enters regular-read mode and sends out the programmed user data in the configured way. All other combinations of bit 1 - bit 5 are not defined and may lead to malfunction of the IC. Table 5-1. Atmel ATA5575M2: Byte 16 Configuration Register Mapping 12345678 ID Length 0 64 bits (96 bits for FSK2 RF/50 coding (2)) 11 2 8 b i t s 1) Modulation

0 Differential bi-phase RF/32 (1)

1 FSK2 RF/50 (2)

Fixed ‘0’ Lock-bits

00001 M e m o r y r e p r o g r a m m a b l e

01101 M e m o r y l o c k e d

  • otherwise - unassigned Bit 6 must always be at '0', otherwise a malfunction will appear Notes: 1. Setting for ISO 11785 FDX-B 2. Setting for ISO 11785 FDX-A

ATA5575M2 [DATASHEET] 9217F–RFID–12/14

5.1.2 Modulation

The modulator consists of data encoders for the following types of modulation.

5.1.3 ID Length

The Atmel® ATA5575M2 offers settings for different ID lengths. If bit 8 of byte 16 is set to '1', the ID length is 128 bits. Depending on the modulation scheme, resetting bit 8 of byte 16 to '0' leads either to the ID length of 64 bit with differential bi- phase coding or to the ID length of 96 bit with FSK2 coding respectively.

5.2 Animal ID and Traceability

During Atmel’s production process the Atmel ATA5575M2 will be pre-configuered in the ISO11784/11785 FDX-B mode and a unique ID (UID) will be stored in the user memory. The unique ID consists of Atmel’s production information like lot number, wafer number, and die-on-wafer number. With these data each chip can be traced and concurrently each chip has its own unique ID for identification purposes(1). For ISO11784/11785 FDX-B telegrams please refer to Section 7. “Examples for Programming the ATA5575M2” on page 14. Section 10.2 “ATA5575M2 Configuration on Delivery” on page 18 describes how the unique ID is formed based on Atmel production information. Note: 1. Please note that this traceability data is only for produ ction control and does not conform with any ISO, national or other regulations.

5.3 Tag-to-reader Communication (Uplink)

Immediately after entering the reader field, generating the internal supply voltage and the analog POR, in the delivery state the tag cycles its data stored in EEPROM by load modulation according to the configuration setting. This resistive load modulation can be detected at the reader device.

5.3.1 Regular-read Mode

In regular-read mode data from the memory is transmitted in series, starting with byte 0, bit 1, up to the last byte, bit 8. Last byte is defined in bit 8 of byte 16, ID Length. When the last bit of the last byte (defined by ID length) has been read, data transmission restarts with byte 0, bit 1. The device enters regular-read mode in delivery state (lock bits set to '00001b' or set to '01101b'; please refer to Section 5.1.1 “Lock-bits” on page 5). Last byte is 15, when ID Length = 1 (128 bit). For differential bi-phase modulation, the last byte is 7 when ID Length = 0 (64 bits) is chosen. For FSK2 RF/50 modulation, the last byte is 11 when ID length = 0 (96 bits) is chosen. Every time the Atmel ATA5575M2 enters regular or byte read mode, the first bit transmitted is a logical '0'. The data stream starts with bit 1 of byte 0 or bit 1 of the addressed byte. Table 5-2. Atmel ATA5575M2: Types of Modulation Symbol Direct Data Output Encoding FSK2 RF/50 FSK/10 – FSK/8 0 = RF/10 1 = RF/8 Differential bi-phase Transition at each bit start 0 creates an additional mid-bit change

7ATA5575M2 [DATASHEET] 9217F–RFID–12/14 Figure 5-1. Examples of Different ID Length Settings

5.3.2 Byte-read Mode

With the direct access command, only the addressed byte is read repetitively. This mode is called byte-read mode. Direct access is entered by transmitting the opcode ('10'), a single 0 bit, and the requested 5-bit byte address.

5.3.3 Dummy Data

The dummy data are a predefined bit sequence of all bits set to value '0'. This sequence is read out instead of the data stored in the user memory if the lock bits are set to '00000b'.

5.4 Reader-to-tag Communication (Downlink)

Data is transmitted to the tag by interrupting the RF field with short field gaps (on-off keying) according to the Atmel® ATA5577 fixed-bit-length protocol (downlink mode). The duration of these field gaps is, for example, 100µs. The time between two gaps encodes the 0/1 information to be transmitted (pulse interval encoding). The time between two gaps is nominally 25 field clocks for a 0 and 58 field clocks for a 1. When there is no gap for more than 64 field clocks after a previous gap, the Atmel ATA5575M2 exits the downlink mode. The tag starts with the command execution if the correct number of bits were received. If an error condition occurs, the Atmel ATA5575M2 does not continue command execution and enters read mode depending on the setting of the lock bits. The initial gap is referred to as the start gap. This triggers reader-to-tag communication. The start gap may need to be longer than subsequent gaps - so-called write gaps - in order to be detected reliably. A start gap is accepted at any time after the mode register has been loaded (≥ 1ms). Figure 5-2. Start of Reader-to-tag Communication (Downlink) Loading byte 16 Byte 6 Byte 7 Byte 1 Byte 0Byte 0 ID Length = ‘0’ with diff. Bi-phase coding ID Length = ‘0’ with FSK2 coding Loading byte 16 Byte 10 Byte 11 Byte 1 Byte 0Byte 0 Loading byte 16 Byte 14 Byte 15 Byte 1 Byte 0Byte 0ID Length = ‘1’ Write modeRead mode Sgap Wgap

ATA5575M2 [DATASHEET] 9217F–RFID–12/14 All absolute times assume TC = 1/fC = 8µs (fC = 125kHz)

5.4.1 Downlink Data Protocol

The Atmel® ATA5575M2 expects to receive a dual bit opcode as a part of a reader command sequence. There are three valid opcodes and overall five different commands (please refer to Figure 5-4 on page 9):

  • The RESET opcode '00' starts an initialization cycle
  • A single '10' opcode (Read ID) leads to reading the ID out of the EEPROM memory. This is suitable to check the programmed user data if the memory is not locked already. The opcode '10' precedes all downlink operations for writing data into the EEPROM
  • The opcode '11' reads the upper bytes when ID length (bit 8 of byte 16) is set to '0' If ID length is set to '1' opcode '11' is the same than opcode '10'
  • The Write Byte requires the opcode '10', a '0' bit, 8 data bits and the 5-bit address (16 bits total)
  • For Direct access, the opcode '10', a '0' bit and a 5-bit address (8 bits total), is required Note: The data bits are read in the same order as written. Figure 5-3. Complete Write Sequence Table 5-3. Downlink Data Decoding Scheme Parameter Remark Symbol Min. Typ. Max. Unit Start gap Sgap 8 15 50 TC Write gap Wgap 8 10 20 TC Write data coding (gap separation) 0 data d0 18 25 33 TC 1 data d1 50 58 65 TC Note: All absolute times are given under the assumption T C = 1/fC = 8µs (fC = 125kHz) Write mode Read modeRead mode ProgrammingByte addressByte data Start gap Configuration loading POR Opcode ‘0’

9ATA5575M2 [DATASHEET] 9217F–RFID–12/14

5.5 Programming

When all necessary information has been received by the ATA5575M2, programming may proceed. There is a clock delay between the end of the writing sequence and the start of programming. Typical programming time is 5.6ms. This cycle includes a data verification read to grant secure and correct programming. After programming is successfully executed, the ATA5575M2 enters byte-read mode, transmitting the byte just programmed. If the command sequence is validated, the new data is programmed into the EEPROM memory. Each programming cycle consists of four consecutive steps: erase byte, erase verification (data = 0), programming, programming verification (corresponding data bits = 1). Figure 5-5. Coil Voltage a fter Programming a Byte Figure 5-4. ATA5575M2 Command Formats OP Write byte 1 0 0 1 Data 8 4 Addr 0 Direct access 1 0 0 4 Addr 0 Read ID 1 0 Read upper bytes 1 1 Reset command 0 0 Read programmed memory byte Read ID Read ID5.6ms (Regular read mode)(Byte read mode)Programming and data verification Write data to tag VCoil 1 - Coil 2

ATA5575M2 [DATASHEET] 9217F–RFID–12/14 6. Error Handling Several error conditions can be detected to ensure that only valid bits are programmed into the EEPROM. There are two error types which result into two different actions.

6.1 Errors During Command Sequence

The following detectable errors could occur when sending a command sequence to the Atmel® ATA5575M2:

  • The wrong number of field clocks between two gaps (i.e., not a valid 1 or 0 pulse stream)
  • The number of bits received in the command sequence is incorrect

6.2 Errors Before/During Programming of EEPROM

If the command sequence was received successfully, the following errors may still prevent programming:

  • The lock bits of the memory are already set
  • If the memory is locked, programming is not possible. The Atmel ATA5575M2 enters byte-read mode, continuously transmitting the currently addressed byte.
  • If a data verification error is detected after programming of an executed data byte, the tag will stop modulation (modulation defeat) until a new command is transmitted. Table 6-1. Bit Counts of Command Sequences Command Number of Bits Write byte 16 Direct access 8 Read ID 2 Read upper bytes 2 Reset command 2

11ATA5575M2 [DATASHEET] 9217F–RFID–12/14 Figure 6-1. Atmel ATA5575 M2 Functional Diagram Byte-read mode Program and verify Write Check Write protection Check Number of bits Command decode Start gap Write OP(1p) Reset Modulation defeat fail data = unchanged fail data = unchanged Gap Command mode Read ID Set-up modes Power-on reset Regular-read mode / Read dummy data okData verification failed data = new Read ID Read upper bytes OP (00) Gap OP(10) Read ID OP(11) Read upper bytes OP(10) Direct access

ATA5575M2 [DATASHEET] 9217F–RFID–12/14 Figure 6-2. Example of Differential Bi-phase Coding with Data Rate RF/32 Data rate =

64 Field Clocks (FC)16 FC

Modulator signalBi-phase coded 16 FC

13ATA5575M2 [DATASHEET] 9217F–RFID–12/14 Figure 6-3. Example of FSK2 Coding wi th Data Rate RF/50, Subcarrier f0 = RF/10, f1 =R F / 8 Data rate =

50 Field Clocks (FC)

f0 = RF/10,f1 = RF/8 Modulator signal

ATA5575M2 [DATASHEET] 9217F–RFID–12/14 7. Examples for Progra mming the ATA5575M2 Animal ID is a typical application with ISO11784/11785. The following describes the data structure of an FDX-B telegram and a flow for programming ATA5575M2 using sample data. Figure 7-1. ATA5575M2: Structure of the ISO 11785 FDX-B Telegram Notes:

  • Except for the header, every 8 bits are followed by one control bit (1), to prevent the header from recurring.
  • All data is transmitted LSB first.
  • Country codes are defined in ISO 3166
  • The bits reserved for future use (RFU) are all set to 0.
  • If the data block flag is not set, the trailer bits are all set to 0.
  • CRC is performed on the 64-bit identification code without the control bits. The generator polynomial is P(x) = x16 +x 12 +x 5 + 1. Reverse CRC-CCITT (0x 8 408) is used. The data stream is LSB first. Example data for programming Atmel ATA5575M2 in FDX-B mode:
  • Animal flag: 1
  • RFU: 0
  • Data block flag: 0
  • Country code: 999
  • Unique number: 123456789
  • Trailer: 0 Header Identification Code CRC Trailer 11 8 x (8+1) 2 x (8+1) 3 x (8+1)Bits 11b fixed 00000000001 LSB MSB MSB LSB Animal Flag RFU 7b RFU 7b Country Code 8b Data Block Flag Country Code Unique Number 6b Unique Number 8b Unique Number 8b Unique Number 8b Unique Number 8b 83 1220 RFU 14b Country Code 10b Unique Number 38b Control bit '1' Control bit '1' Control bit '1' Control bit '1' Control bit '1' Control bit '1' Control bit '1' Control bit '1' 64b Identification Code +8b 16b CRC +2b 24b Trailer all '0' +3b Control bit '1' Bit No. LSB MSB

15ATA5575M2 [DATASHEET] 9217F–RFID–12/14 Table 7-1. Atmel ATA5575M2: Progra mming with FDX-B Example Data Base Station Atmel ATA5575M2 Field on for t = 5ms POR and regular-read mode Command 00 Reset Command 10 0 0000 1001 10000 Programming byte 16 with ‘09h’ (FDX-B mode, memory reprogrammable) Command 10 0 0000 0000 00000 Programming byte 0 with ‘00h’ Command 10 0 0011 0101 00001 Programming byte 1 with ‘35h’ Command 10 0 0001 1011 00010 Programming byte 2 with ‘1Bh’ Command 10 0 0011 1110 00011 Programming byte 3 with ‘3Eh’ Command 10 0 1101 0111 00100 Programming byte 4 with ‘D7h’ Command 10 0 1000 0010 00101 Programming byte 5 with ‘82h’ Command 10 0 0000 0111 00110 Programming byte 6 with ‘07h’ Command 10 0 1001 1111 00111 Programming byte 7 with ‘9Fh’ Command 10 0 1000 0000 01000 Programming byte 8 with ‘80h’ Command 10 0 0100 0000 01001 Programming byte 9 with ‘40h’ Command 10 0 0110 1110 01010 Programming byte 10 with ‘6Eh’ Command 10 0 1001 1000 01011 Programming byte 11 with ‘98h’ Command 10 0 1010 1000 01100 Programming byte 12 with ‘A8h’ Command 10 0 0000 0100 01101 Programming byte 13 with ‘04h’ Command 10 0 0000 0010 01110 Programming byte 14 with ‘02h’ Command 10 0 0000 0001 01111 Programming byte 15 with ‘01h’ Command 10 Read ID Field on for t = 50ms Read and verify FDX-B data Send FDX-B data Command 10 0 0110 1001 10000 Programming byte 16 with ‘69h’ (FDX-B mode, memory locked) Command 00 Reset Field on for t = 50ms Read and verify FDX-B data Send FDX-B data

ATA5575M2 [DATASHEET] 9217F–RFID–12/14 8. Absolute Maximum Ratings Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. Parameters Symbol Value Unit Maximum DC current into Coil1/Coil2 Icoil 20 mA Maximum AC current into Coil1/Coil2 f = 125kHz Icoil p 20 mA Power dissipation (dice) (free-air condition, time of application: 1s) Ptot 100 mW Electrostatic discharge maximum to ANSI/ESD-STM5.1-2001 standard (HBM) Vmax 2000 V Operating ambient temperature range Tamb –40 to +85 °C Storage temperature range Tstg –40 to +150 °C Note: For data retention please refer to Section 9. “Electrical Characteristics” on page 16. 9. Electrical Characteristics Tamb = +25°C; fcoil = 125kHz; unless otherwise specified No. Parameters Test Conditions Symbol Min. Typ. Max. Unit Type*

1 RF frequency range fRF 100 125 150 kHz

2.1 Supply current (without current consumed by the external LC tank circuit) Tamb = 25°C (1) IDD 1.5 3 µA T

2.2 Read – full temperature

range 2 5 µA Q

2.3 Programming – full

temperature range 25 µA Q 3.1 Coil voltage (AC supply) Read mode and write command 2) Vcoil pp 6 Vclamp V Q

3.2 Program EEPROM(2) 16 Vclamp V Q

4 Start-up time Vcoil pp = 6V tstartup 1.1 ms Q 5.1 Clamp 3mA current into Coil1/2 Vpp 15 18 21 V T 5.2 20mA current into Coil1/2 Vpp 17 20 24 V T 6.1 Modulation parameters 3mA current into Coil1/2 and modulation ON Vpp 2 3 4 V T 6.2 20mA current into Coil1/2 and modulation ON Vpp 4.5 5 8.5 V T

6.3 Thermal stability of

Vp/Tamb –1 mV/°C Q *) Type means: T: directly or indirectly tested during production; Q: guaranteed based on initial product qualification data 2. Current into Coil1/Coil2 is limited to 10mA. 3. Since the EEPROM performance is influenced by assembly pr ocesses, Atmel cannot confirm the parameters for -DDW (tested die on unsawn wafer) delivery. 4. See Section 10. “Ordering Information” on page 18.

17ATA5575M2 [DATASHEET] 9217F–RFID–12/14

7.1 Clock detection level Vcoil pp = 8V Vclkdet 400 550 750 mV T

7.2 Gap detection level Vcoil pp = 8V Vgapdet med 400 550 750 mV T

8 Programming time

(64 + 648 internal clocks) Tprog 5 5.7 6 ms T

9 Endurance Erase all/Write all(3) ncycle 100000 Cycles Q

10.1 Data retention Top = 55°C(3) tretention 10 20 50 Years Q

10.2 Top = 150°C(3) tretention 96 hrs T

10.3 Top = 250°C(3) tretention 24 hrs Q

11.1 Resonance capacitor Mask option(4) Vcoil pp = 1V Cr 320 330 340 pF T 11.2 242 250 258 9. Electrical Characteristics (Continued) Tamb = +25°C; fcoil = 125kHz; unless otherwise specified No. Parameters Test Conditions Symbol Min. Typ. Max. Unit Type* *) Type means: T: directly or indirectly tested during production; Q: guaranteed based on initial product qualification data 2. Current into Coil1/Coil2 is limited to 10mA. 3. Since the EEPROM performance is influenced by assembly pr ocesses, Atmel cannot confirm the parameters for -DDW (tested die on unsawn wafer) delivery. 4. See Section 10. “Ordering Information” on page 18.

ATA5575M2 [DATASHEET] 9217F–RFID–12/14 10. Ordering Information

10.1 Available Order Codes

New order codes will be created by customer request if order quantities exceed 250k pieces.

10.2 ATA5575M2 Configuration on Delivery

On delivery Atmel’s production information is stored in EEPROM with the FDX-B data structure as described in Figure 7-1 on page 14. The user data contains Atmel’s lot and production information as described in Table 10-2. With 38 bits, 12 decimals in the range from 0 to 274 877 906 943 can be formed. The following Atmel production information is stored within these 12 decimal places. ATA5575M2 ccc -xxx Package Drawing DDB 6” sawn wafer on foil with ring, thickness 150µm (approx. 6mil) Figure 11-1 on page 21 DBB 6” sawn wafer on foil with ring and gold bumps 25µm, thickness 150µm (approx. 6mil) Figure 11-2 on page 22 DBQ Die in blister tape with gold bumps 25µm, thickness 280µm Figure 11-3 on page 23 On-chip Capacity Value in pF 250 (planned) 330 33A DBB 6” sawn wafer on foil 25µm, thickness 280µm (11mil) Figure 11-4 on page 24 Table 10-1. ATA5575M2: Configuration on Delivery Byte Address Value Comment User data byte 0 to byte 15 0b 0 0000 to 0b 0 1111 Variable data Unique ID within a FDX-B telegram Configuration (byte 16) 0b 1 0000 0x 09 Send FDX-B telegram with user data byte 0 to byte 15 Table 10-2. Atmel ATA5575M2: Meaning of the Digi ts of Unique Number in Delivery State Decimal 11 10, 9 8 7 6 5, 4, 3, 2 1, 0 Denotation Header CID ICR Y Q NNNN Wafer# Range [dec] 1 (fixed) 1-99 0-9 0-9 1-4 0-9999 1-25 For example 1 04 0 9 1 0164 12

19ATA5575M2 [DATASHEET] 9217F–RFID–12/14 Notes:

  • First decimal Header is always fixed at ‘1’
  • CID denotes the chip ID and is set to ‘4’ for Atmel® ATA5575M2
  • ICR stands for the revision and/or foundry version of the IC
  • YQNNNN gives the Atmel lot information
  • Y: alphanumeric 0, …, 9
  • Q: Characters F, G, H and J - are transformed to 1, …, 4
  • NNNN: Alphanumeric consecutive number 0, …, 9999
  • Wafer# describes a lot's wafer numbers; alphanumeric 1, …, 25 The Unique Number will then calculated to: Unique Number = Header × 1011 + CID × 109 + ICR × 108 + Y × 107 + Q × 106 + NNNN × 102 + Wafer# For the example given in Table 10-2 on page 18 the Unique Number is 104 091 016 412 With the 24 trailer bits 8 decimals in the range 0 to 16 777 216 can be established. The following Atmel production information is stored within these 8 decimal places. Notes:
  • The first 3 decimals of the Header are always fixed: '111'
  • Die on wafer (DW): Consecutive number of die on wafer: 1 to 99 999 The Trailer is then calculated to: Trailer = Header × 105 + DW With the example given in Table 10-3 the Trailer is 11 109 127 Table 10-3. Atmel ATA5575M2: M eaning of the Digits of Trailer Bits in Delivery State Decimal 7, 6, 5 4, 3, 2, 1, 0 Denotation Header Die-on-wafer no. (DW) Range [dec] 111 (fixed) 0 to 99 999 For example 111 09 127

ATA5575M2 [DATASHEET] 9217F–RFID–12/14

10.2.1 ATA5575M2 Example for Memory Content on Delivery

The following describes an example of the memory content after Atmel’®s production.

  • CID: 4
  • ICR: '00b'
  • Lot number: 9F0164
  • Wafer number: 12
  • Die on wafer: 9.127 Unique Number = 1 × 1011 + 4 × 109 + 0 × 108 + 9 × 107 + 1 × 106 + 0164 × 102 + 12 = 104 091 016 412 Trailer = 111 × 105 + 9,127 = 11 109 127 With the sample data above the FDX-B telegram fields are:
  • Animal flag ( 1 bit) = ‘1b’ fixed
  • RFU (14 bit) = ’00 0000 0000 0000b’ fixed
  • Data block flag (1 bit) = ‘0b’ fixed
  • Country code (10 bit) = 999 (= '11 1110 0111b') fixed
  • Unique number (38 bit) = 104 091 016 412
  • CRC (16 bit) = 39 505
  • Trailer (24 bit) = 11 109 127 Table 10-4. ATA5575M2: Example of Memory Content on Delivery Byte# 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 Meaning Header Header/ Unique Number Unique number Unique number Unique number Unique number Unique number/ Country Code Country code Data Block Flag/ RFU RFU RFU/ Animal Flag/ CRC CRC CRC/ Trailer Trailer Trailer Trailer Confi- guration Value [hex] 00 27 73 BB 94 F2 37 9F 80 40 71 55 9F 07 07 2B 09

21ATA5575M2 [DATASHEET] 9217F–RFID–12/14 11. Package Information Figure 11-1. 6” Wafer on Foil with Ring Package Drawing Contact: packagedrawings@atmel.com GPC DRAWING NO. REV. TITLE 9.920-6716.01-4 3 01/18/11 Dimensions ATA5575MYxxxC-DDB 13 3 0 250 330 22 5 0 Option Y Option xxx 20:1 Die Dimensions Dimensions in mm specifications according to DIN technical drawings Orientation on frame Ø 227.7 212 Ø194.5 Ø150 212 87.5 86.5 Wafer ATA5575MYxxx-DDB 6" Wafer frame, plastic thickness 2.5mm UV Tape Adwill D176 Label: Qty: Wafer no: Lot no: Prod: ATA5575MYxxx-DDB 59.5 63.6 B AØ3 A 0.15±0.012 0.966 0.402 0.4 (0.08) 0.326 0.04 × 45° (0.08) 0.21 0.2 0.946 C2 C1

ATA5575M2 [DATASHEET] 9217F–RFID–12/14 Figure 11-2. 6” Wafer on Foil with Ring and Gold Bumps 25µm Package Drawing Contact: packagedrawings@atmel.com GPC DRAWING NO. REV. TITLE 9.920-6716.02-4 3 01/18/11 Dimensions ATA5575MYxxx-DBB 20:1 Die Dimensions Dimensions in mm specifications according to DIN technical drawings Orientation on frame Ø 227.7 212 Ø194.5 Ø150 212 87.5 86.5 Wafer ATA5575MYxxx-DBB 6" Wafer frame, plastic thickness 2.5mm UV Tape Adwill D176 Label: Qty: Wafer no: Lot no: Prod: ATA5575MYxxx-DBB 59.5 63.6 B AØ3 A 0.966 0.402 0.4 (0.08) 0.326 0.04 × 45° (0.08) 0.21 0.2 0.946 C2 C1 0.155±0.014 0.025±0.005 0.15±0.012 0.175±0.017 (Au bump) 0.005±0.002 (BCB coating) 1 330 250 330 2 250 Option Y Option xxx

23ATA5575M2 [DATASHEET] 9217F–RFID–12/14 Figure 11-3. Die in Blister Tape with Gold Bumps 25µm Package Drawing Contact: packagedrawings@atmel.com GPC DRAWING NO. REV. TITLE 9.800-5108.01-4 2 04/03/12 Dimensions ATA5575MYxxx-DBQ specifications according to DIN technical drawings 20:1 Die Dimensions C2 C1 (BCB coating) 0.285±0.0135 0.005±0.0015 (Au bump) 0.025±0.005 0.305±0.017 0.28±0.012 8.4 reel Ø330 Ø1.55 (0.08) 0.946 0.21 0.2 41 . 2 0.47 0.25 (0.08) 0.4 3.51.2 0.402 0.966 0.326 0.04 × 45° ’’X’’ ’’X’’ Label acc. ’’Packaging and Packing Spec.’’ cover tape carrier tape Specification Tape and reel Dimensions in mm Packing acc. IEC 60286-3 1 330 250 330 2 250 Option Y Option xxx

ATA5575M2 [DATASHEET] 9217F–RFID–12/14 Figure 11-4. 6” Sawn Wafer on Foil 25µm Package Drawing Contact: packagedrawings@atmel.com GPC DRAWING NO. REV. TITLE 9.920-6716.03-4 1 12/02/14 Chip Dimensions ATA5575MYxxx-DDB Dimensions in mm specifications according to DIN technical drawings 20:1 Die Dimensions Orientation on frame (0.08)212 87.5 86.5 0.4 0.966 0.402 Wafer ATA5575MYxxx-DBB 6" Wafer frame, plastic thickness 2.5mm UV Tape Adwill D176 Label: Qty: Wafer no: Lot no: Prod: ATA5575MYxxx-DBB B Ø 227.7 Ø 150 Ø 194.5 A A 0.946 0.21 0.326 59.5 63.6 212 0.04x45° 0.2 (0.08) 0.285±0.0135 0.025±0.005 0.28±0.012 0.305±0.017 0.005±0.0015 (BCB coating) (Au bump) 33A Option xxx Option Y

25ATA5575M2 [DATASHEET] 9217F–RFID–12/14 12. Revision History Please note that the following page numbers referred to in this section refer to the specific revision mentioned, not to this document. Revision No. History 9217F-RFID-12/14

  • Section 10 “Ordering Information” on page 18 updated
  • Figure 11-4 “6” sawn wafer on foil 25µm” on page 24 added 9217E-RFID-06/14 • Put datasheet in the latest template 9217D-RFID-04/13
  • Section 10 “Ordering Information” on page 18 updated
  • Section 11 “Package Information” on page 23 updated 9217C-RFID-12/11 • Set datasheet from Preliminary to Standard 9217B-RFID-05/11
  • Section 1 “Description” on page 1 changed
  • Section 4 “Analog Front End (AFE) on pages 3 to 4 changed
  • Section 5 “Operating the Atmel ATA5575M2” on pages 5 to 9 changed
  • Section 6.2 Errors Before/During Programming of EEPROM” on page 11 changed
  • Section 8 “Absolute Maximum Ratings” on page 16 changed
  • Section 9 “Electrical Characteristics” on page 16 changed
  • Section 10.2 “Atmel ATA5575M2 Configuration on Delivery” on pages 18 to 19 changed

Atmel Corporation 1600 Technology Drive, San Jose, CA 95110 USA T: (+1)(408) 441.0311 F: (+1)(408) 436.4200 | www.atmel.com © 2014 Atmel Corporation. / Rev.: 9217F–RFID–12/14 Atmel®, Atmel logo and combinations thereof, Enabling Unlimited Possibilities®, and others are registered trademarks or trademarks of Atmel Corporation in U.S. and other countries. Other terms and product names may be trademarks of others. DISCLAIMER: The information in this document is provided in c onnection with Atmel products. No license, express or implied, by estoppel or otherwise, to any intellectual property right is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN THE ATMEL TERMS AND CONDIT IONS OF SALES LOCATED ON THE ATMEL WEBSITE, ATMEL ASSUMES NO LIABILITY WH ATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY WARRANTY RELATING TO ITS P RODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT, CONSEQUENTIAL, PU NITIVE, SPECIAL OR INCIDENTAL DAMAGES (INCLUDING, WITHOUT LIMI TATION, DAMAGES FOR LOSS AND PROFITS, BUSINESS INTERRUPTION, OR LOSS OF INFORMATION ) ARISING OUT OF THE USE OR INABILITY TO USE THIS DOCUMENT, EVEN IF ATMEL HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Atmel makes no r epresentations or warranties with respect to the accuracy or c ompleteness of the contents of this document and reserves the right to make changes to specificatio ns and products descriptions at any time without notice. Atmel d oes not make any commitment to update the information contained herein. Unless specifically provided otherwise, Atme l products are not suitable for, and shall not be used in, automo tive applications. Atmel products are not intended, authorized, or warranted for use as components in applications intended to support or sustain life. SAFETY-CRITICAL, MILITARY, AND AUTOMOTIVE APPLICATIONS DISCLAIM ER: Atmel products are not designed for and will not be used in connection with any applications where the failure of such products would reasonably be expected to re sult in significant personal inju ry or death (“Safety-Critical A pplications”) without an Atmel officer's specific written consent. Safety-Critical Applications incl ude, without limitation, life support devices and systems, equipment or systems for t he operation of nuclear facilities and weapons systems. Atmel products are not designed nor intended for use in military or aerospace applications or environments unless specifically designated by Atmel as military-grade. Atmel products are not designed nor intended for use in automot ive applications unless spec ifically designated by Atmel as automotive-grade.