ASK ATMEL | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 13

Technical content

Features

  • Integrated PLL Loop Filter  ESD Protection also at ANT1/ANT2 (4 kV HBM/200V MM; Except Pin 2: 4 kV HBM/100V MM)  High Output Power (5.5 dBm) with Low Supply Current (8.5 mA)  Modulation Scheme ASK/FSK – FSK Modulation is Achieved by Connecting an Additional Capacitor Between the XTAL Load Capacitor and the Open Drain Output of the Modulating Microcontroller  Easy to Design-in Due to Excellent Isolation of the PLL from the PA and Power Supply  Single Li-cell for Power Supply  Supply Voltage 2.0V to 4.0V in the Temperature Range of –40°C to +85°C/+125°C  Package TSSOP8L  Single-ended Antenna Output with High Efficient Power Amplifier  CLK Output for Clocking the Microcontroller  One-chip Solution with Minimum External Circuitry  125°C Operation for Tire Pressure Systems 1. Description The T5750 is a PLL transmitter IC whic h has been developed for the demands of RF low-cost transmission systems at data rates up to 32 kBaud. The transmitting frequency range is 868 MHz to 928 MHz. It can be used in both FSK and ASK systems. Figure 1-1. System Block Diagram Micro- controller PLL UHF ASK/FSK Remote control receiver UHF ASK/FSK Remote control transmitter T5750 T5760/ T5761 LNA VCO PLL XTO LNA VCO Antenna Demod Control 1 to 3 Encoder ATARx9x XTO

1 Li cell

4546F–RKE–12/08

4546F–RKE–12/08 T5750 2. Pin Configuration Figure 2-1. Pinning TSSOP8L ENABLE VS GND XTAL CLK PA_ENABLE ANT2 ANT1 Table 2-1. Pin Description Pin Symbol Function Configuration 1C L K Clock output signal for micro con roller The clock output frequency is set by the crystal to fXTAL/4

2 PA_ENABLE Switches on power amplifier, used for

Emitter of antenna output stage Open collector antenna output 100Ω 100Ω CLK VS 50 kΩ 20 µA UREF = 1.1V PA_ENABLE ANT1 ANT2

4546F–RKE–12/08 T5750 Figure 2-2. Block Diagram

5 XTAL Connection for crystal

6 VS Supply voltage See ESD protection circuitry (see Figure 4-5 on page 9)

7 GND Ground See ESD protection circuitry (see Figure 4-5 on page 9)

8 ENABLE Enable input

Table 2-1. Pin Description (Continued) Pin Symbol Function Configuration 1.5 kΩ 1.2 kΩ 182 µA XTAL VS VS 200 kΩ ENABLE T5750 CP Power up/down PDF XTAL VS GND ENABLE ANT1 ANT2 PA_ENABLE CLK f LF PA VCO PLL XTO f

4546F–RKE–12/08 T5750 3. General Description This fully integrated PLL transmit ter allows particularly simple, low-cost RF miniature transmit- ters to be assembled. The VCO is locked to 64 × fXTAL hence a 13.5672 MHz crystal is needed for a 868.3 MHz transmitter and a 14.2969 MHz crystal for a 915 MHz transmitter. All other PLL and VCO peripheral elements are integrated. The XTO is a series resonance oscillator so that only one capacitor toget her with a crystal con- nected in series to GND are needed as external elements. The crystal oscillator together with the PLL needs typically < 1 ms until the PLL is locked and the CLK output is stable. There is a wait time of ≥ 4 ms must be used until the CLK is used for the microcontroller and the PA is switched on. The power amplifier is an open-collector output delivering a current pulse which is nearly inde- pendent from the load impedance. The delivered output power is hence controllable via the connected load impedance. This output configuration enables a simple matching to any kind of antenna or to 50 Ω. A high power efficiency of η=P out/(IS,PA × VS) of 24% for the power amplifier at 868.3 MHz results when an optimized load impedance of ZLoad = (166 + j226)Ω is used at 3V supply voltage. 4. Functional Description If ENABLE = L and the PA_ENABLE = L, the circuit is in standby mode consuming only a very small amount of current, so that a lithium cell used as power supply can work for several years. With ENABLE = H the XTO, PLL and the CLK driver are switched on. If PA_ENABLE remains L only the PLL and the XTO is running and the CLK signal is delivered to the microcontroller. The VCO locks to 64 times the XTO frequency. With ENABLE = H and PA_ENABLE = H the PLL, XTO, CLK driver and the power amplifier are on. With PA_ENABLE the power amplifier can be switched on and off, which is used to perform the ASK modulation.

4.1 ASK Transmission

The T5750 is activated by ENABLE = H. PA_ENABLE must remain L for t ≥ 4 ms, then the CLK signal can be taken to clock the microcontro ller and the output power can be modulated by means of pin PA_ENABLE. Afte r transmission PA_ENABLE is s witched to L and the microcon- troller switches back to internal clocking. The T5750 is switched back to standby mode with ENABLE = L.

4.2 FSK Transmission

The T5750 is activated by ENABLE = H. PA_ENABLE must remain L for t ≥ 4 ms, then the CLK signal can be taken to clock the microcontrolle r and the power amplifier is switched on with PA_ENABLE = H. The chip is then ready for F SK modulation. The microcontroller starts to switch on and off the capacitor between the XTAL load capacitor and GND with an open-drain output port, thus changing the reference frequency of the PLL. If the switch is closed, the output frequency is lower than if the switch is open. A fter transmission PA_ENABLE is switched to L and the microcontroller switches back to inte rnal clocking. The T5750 is switched back to standby mode with ENABLE = L. The accuracy of the frequency dev iation with XTAL pulling method is about ±25% when the fol- lowing tolerances are considered.

4546F–RKE–12/08 T5750 Figure 4-1. Tolerances of Frequency Modulation Using C4 =9 . 2p F± 2 % , C5 = 6.8 pF ±5%, a switch port with C Switch = 3 pF ±10%, stray capaci- tances on each side of the crystal of C Stray1 =C Stray2 = 1 pF ±10%, a parallel capacitance of the crystal of C0 = 3.2 pF ±10% and a crystal with C M = 13 fF ±10%, an FSK deviation of ±21.5 kHz typical with worst case tolerances of ±16.8 kHz to ±28.0 kHz results.

4.3 CLK Output

An output CLK signal is provided for a connect ed microcontroller, the delivered signal is CMOS compatible if the load capacitance is lower than 10 pF.

4.3.1 Clock Pulse Take-over

The clock of the crystal oscillator can be used for clocking the microcontroller. Atmel ®’s ATARx9x has the special feature of starting with an integrated RC-oscillator to switch on the T5750 with ENABLE = H, and after 4 ms to assume the clock signal of the transmission IC, so that the message can be sent with crystal accuracy.

4.3.2 Output Matching and Power Setting

The output power is set by the load impedance of the antenna. The maximum output power is achieved with a load impedance of Z Load,opt = (166 + j226)Ω at 868.3 MHz. There must be a low resistive path to VS to deliver the DC current. The delivered current pulse of the power ampl ifier is 7.7 mA and the maximum output power is delivered to a resistive load of 475 Ω if the 0.53 pF output capacitance of the power amplifier is compensated by the load impedance. An optimum load impedance of: ZLoad = 475Ω || j/(2 × p × f × 0.53 pF) = (166 + j226) Ω thus results for the maximum output power of 5.5 dBm. The load impedance is defined as the impedance seen from the T5750’s ANT1, ANT2 into the matching network. Do not confuse this large signal load impedance with a small signal input impedance delivered as input characteristic of RF amplifiers and measured from the application into the IC instead of from the IC into the application for a power amplifier. Less output power is achieved by lowering the real parallel part of 475Ω where the parallel imag- inary part should be kept constant. Output power measurement can be done with the circuit of Figure 4-2 on page 6 . Note that the component values must be changed to compensate the individual board parasitics until the T5750 has the right load impedance Z Load,opt = (166 + j226)Ω at 868.3 MHz. Also the damping of the cable used to measure the output power must be calibrated out. RS LM C4 CM VS XTAL C0 C5 CSwitch CStray1 CStray2

4546F–RKE–12/08 T5750 Figure 4-2. Output Power Measurement

4.4 Application Circuit

For the supply-voltage blocking capacitor C3 a value of 68 nF/X7R is recommended (see Figure 4-3 on page 7 and Figure 4-4 on page 8). C1 and C2 are used to match the loop antenna to the power amplifier where C 1 typically is 3.9 pF/NP0 and C 2 is 1 pF/NP0; for C 2 two capacitors in series should be used to achieve a better tolerance value and to have the possibility to realize the ZLoad,opt by using standard valued capacitors. C1 forms together with the pins of T5750 and th e PCB board wires a series resonance loop that suppresses the 1 st harmonic, hence the position of C 1 on the PCB is important. Normally the best suppression is achieved when C 1 is placed as close as possible to the pins ANT1 and ANT2. The loop antenna should not exceed a width of 1. 5 mm, otherwise the Q-factor of the loop antenna is too high. L1 (≈ 50 nH to 100 nH) can be printed on PCB. C 4 should be selected so that the XTO runs on the load resonance frequency of the crystal. Normally, a value of 12 pF results for a 15 pF load-capacitance crystal. 1 nF 1.5 pF 2.7 pF 10 nH VS Rin ANT2 ANT1 ZLopt Power meter 50Ω Z = 50Ω

4546F–RKE–12/08 T5750 Figure 4-3. ASK Application Circuit ATARx9x T5750 CP Power up/down PDF VDD BPXY VSS VS XTAL XTAL VS VS VS GND ENABLE ANT1 Loop Antenna C2 ANT2 PA_ENABLE OSC1 BPXY BPXY BPXYS1 CLK f LF PA VCO PLL XTO f

4546F–RKE–12/08 T5750 Figure 4-4. FSK Application Circuit ATARx9x T5750 CP Power up/down PDF VDD BPXY VSS VS XTAL XTAL VS VS VS GND ENABLE ANT1 Loop Antenna C2 ANT2 PA_ENABLE OSC1 BPXY BPXY BPXYS1 CLK f LF PA VCO PLL XTO f BP42/T2O

4546F–RKE–12/08 T5750 Figure 4-5. ESD Protection Circuit CLK VS GND PA_ENABLE XTALANT2 ENABLE ANT1 5. Absolute Maximum Ratings Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. Parameters Symbol Minimum Maximum Unit Supply voltage V S 5V Power dissipation P tot 100 mW Junction temperature T j 150 °C Storage temperature T stg –55 125 °C Ambient temperature T amb –55 125 °C Input voltage V maxPA_ENABLE –0.3 (V S + 0.3)(1) V 6. Thermal Resistance Parameters Symbol Value Unit Junction ambient R thJA 170 K/W 7. Electrical Characteristics VS = 2.0V to 4.0V, Tamb = –40°C to 125°C unless otherwise specified. Typical values are given at VS = 3.0V and Tamb = 25°C. All parameters are referred to GND (pin 7). Parameters Test Conditions Symbol Min. Typ. Max. Unit Supply current Power down, VENABLE < 0.25V, –40°C to 85°C VPA_ENABLE < 0.25V, –85°C to +125°C VPA_ENABLE < 0.25V, 25°C (100% correlation tested) IS_Off <10 350 nA µA nA Supply current Power up, PA off, VS = 3V, VENABLE >1 . 7 V , VPA_ENABLE < 0.25V IS 3.6 4.6 mA Power up, VS =3 . 0 , VENABLE >1 . 7 V , VPA_ENABLE >1 . 7 V IS_Transmit 8.5 11 mA Output power VS = 3.0V, Tamb =2 5 ° C , f = 868.3 MHz, ZLoad = (166 + j226)Ω PRef 3.5 5.5 8 dBm Note: 1. If V S is higher than 3.6V, the maximum voltage will be reduced to 3.6V.

4546F–RKE–12/08 T5750 Output power variation for the full temperature range Tamb = –40°C to +85°C, VS = 3.0V VS = 2.0V ΔPRef ΔPRef –1.5 –4.0 dB dB Output power variation for the full temperature range Tamb = –40°C to +125°C, VS = 3.0V VS = 2.0V, POut = PRef + ΔPRef ΔPRef ΔPRef –2.0 –4.5 dB dB Achievable output-power range Selectable by load impedance P Out_typ –3 +5.5 dBm Spurious emission fCLK = f0/128 Load capacitance at pin CLK = 10 pF f O ±1 × fCLK fO ±4 × fCLK other spurious are lower –52 –52 dBc dBc Oscillator frequency XTO (= phase comparator frequency) fXTO = f0/64 fXTAL = resonant frequency of the XTAL, CM ≤ 10 fF , load capacitance selected accordingly T amb = –40°C to +85°C, Tamb = –40°C to +125°C fXTO –30 –40 fXTAL +30 +40 ppm ppm PLL loop bandwidth 250 kHz Phase noise of phase comparator Referred to fPC = fXT0, 25 kHz distance to carrier –116 –110 dBc/Hz In loop phase noise PLL 25 kHz distance to carrier –80 –74 dBc/Hz Phase noise VCO at 1 MHz at 36 MHz –89 –120 –86 –117 dBc/Hz dBc/Hz Frequency range of VCO f VCO 868 928 MHz Clock output frequency (CMOS microcontroller compatible) f0/256 MHz Voltage swing at pin CLK C Load ≤ 10 pF V0h V0l VS × 0.8 VS × 0.2 V V Series resonance R of the crystal Rs 110 Ω Capacitive load at pin XT0 7p F FSK modulation frequency rate Duty cycle of the modulation signal = 50% 0 32 kHz ASK modulation frequency rate Duty cycle of the modulation signal = 50% 0 32 kHz ENABLE input Low level input voltage High level input voltage Input current high VIl VIh IIn 1.7 0.25 V V µA PA_ENABLE input Low level input voltage High level input voltage Input current high VIl VIh IIn 1.7 0.25 VS (1) V V µA 7. Electrical Characteristics (Continued) VS = 2.0V to 4.0V, Tamb = –40°C to 125°C unless otherwise specified. Typical values are given at VS = 3.0V and Tamb = 25°C. All parameters are referred to GND (pin 7). Parameters Test Conditions Symbol Min. Typ. Max. Unit Note: 1. If V S is higher than 3.6V, the maximum voltage will be reduced to 3.6V.

4546F–RKE–12/08 T5750 9. Package Information 8. Ordering Information Extended Type Number Package Remarks T5750-6AQJ TSSOP8L Taped and reeled, Marking: T570, Pb-free 3±0.1 0.85±0.05 0.1±0.05 specifications according to DIN technical drawings Issue: 2; 15.03.04 Drawing-No.: 6.543-5083.01-4 14 Package: TSSOP 8L Dimensions in mm 0.65 nom. 3 x 0.65 = 1.95 nom. 0.31-0.07 +0.06 0.15 -0.02+0.05 1-0.15 +0.05 3.8±0.3 4.9±0.1 3±0.1

4546F–RKE–12/08 T5750 10. Revision History Please note that the following page numbers referred to in this section refer to the specific revision mentioned, not to this document. Revision No. History 4546F-RKE-12/08 • Put datasheet in the newest template

  • Section 7 “Electrical Characteristics” on page 10 changed 4546E-RKE-02/07 • Put datasheet in the newest template
  • Pb-free logo on page 1 deleted 4546D-RKE-09/05 • Pb-free logo on page 1 added
  • Ordering Information on page 11 changed 4546C-RKE-05/05
  • Put datasheet in the newest template
  • Rename M4xCx9x in ATARx9x
  • Table “Absolute Maximum Ratings” on page 9: New heading rows added 4546B-RKE-07/04
  • Table “Absolute Maximum Ratings” on page 9: row “Input voltage” added
  • Table “Absolute Maximum Ratings” on page 9: table note 1 added
  • Table “Electrical Characteristics” on pages 9 to 10: row “PA_ENABLE input” changed
  • Table “Electrical Characteristics” on pages 9 to 10: table note 1 added
  • Table “Ordering Informations” on page 11: Remarks changed

4546F–RKE–12/08 Headquarters International Atmel Corporation

2325 Orchard Parkway

San Jose, CA 95131 USA Tel: 1(408) 441-0311 Fax: 1(408) 487-2600 Atmel Asia Unit 1-5 & 16, 19/F BEA Tower, Millennium City 5

418 Kwun Tong Road

Kwun Tong, Kowloon Hong Kong Tel: (852) 2245-6100 Fax: (852) 2722-1369 Atmel Europe Le Krebs 8, Rue Jean-Pierre Timbaud BP 309 78054 Saint-Quentin-en-Yvelines Cedex France Atmel Japan 9F, Tonetsu Shinkawa Bldg. 1-24-8 Shinkawa Chuo-ku, Tokyo 104-0033 Japan Tel: (81) 3-3523-3551 Fax: (81) 3-3523-7581 Product Contact Web Site www.atmel.com Technical Support auto_control@atmel.com Sales Contact www.atmel.com/contacts Literature Requests www.atmel.com/literature Disclaimer: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any intellectual property right is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN ATMEL ’S TERMS AND CONDI- TIONS OF SALE LOCATED ON ATMEL ’S WEB SITE, ATMEL ASSUMES NO LI ABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTOR Y WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICU LAR PURPOSE, OR NON-INFRINGEMENT. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT, CONSEQUENTIAL, PUNITIVE, SPECIAL OR I NCIDEN- TAL DAMAGES (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF PROFITS, BUSINESS INTERRUPTION, OR LOSS OF INFORMATION) ARISING OUT OF THE USE OR INABILITY TO USE THIS DOCUMENT, EVEN IF ATME L HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Atmel makes no representations or warranties with respect to the accuracy or comp leteness of the contents of this document and reserves the rig ht to make changes to specifications and product descriptions at any time without notice. Atmel does not make any commitment to update the information contained her ein. Unless specifically provided otherwise, Atmel products are not suitable for, and shall not be used in, automotive applications. Atmel’s products are not int ended, authorized, or warranted for use as components in applications in tended to support or sustain life. © 2008 Atmel Corporation. All rights reserved. Atmel ®, Atmel logo and combinations thereof, and others are registered trademarks or trade- marks of Atmel Corporation or its subsidiaries. Other terms and product names may be trademarks of others.