AS10515F16MIL MICROSS | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 4

Technical content

Rev. 2.2 01/10 Micross Components reserves the right to change products or specifi cations without notice. For more products and information please visit our web site at www.micross.com AVAILABLE AS MILITARY SPECIFICATIONS

  • Military Equivalent Screening - 883 1.2.2 Quad Line Receiver PIN ASSIGNMENT (Top View) 16-Pin FlatPack (F) GENERAL DESCRIPTION The AS10515F16MIL is a quad differential amplifi er de- signed for use in sensing differential signals over long lines. The base bias supply (VBB) is made available at pin 9 to make the device useful as a Schmitt trigger, or in other applications where a stable reference voltage is necessary. Active current sources provide the AS10515F16MIL with excellent common mode noise rejection. If any amplifi er in a package is not used, one input of that amplifi er must be con- nected to V BB (pin 9) to prevent upsetting the current source bias network.
  • PD = 150mW Max/Pkg (No Load)
  • tpd = 2.0ns typ
  • tr, tf = 2.0ns type (20% - 80%) FUNCTION FLATS BURN-IN (CONDITION C) VCC1 5G N D AOUT 6 51 Ω to VTT BOUT 7 51 Ω to VTT AIN\\ 8 VBB AIN 9G N D BIN 10 GND BIN\\ 11 VBB VEE 12 VEE VBB 13 VBB CIN\\ 14 VBB CIN 15 GND DIN 16 GND DIN\\ 1 VBB COUT 2 51 Ω to VTT DOUT 3 51 Ω to VTT VCC2 4G N D PIN ASSIGNMENTS BURN-IN CONDITIONS: VTT = -2.0V MAX/ -2.2V MIN VEE = -5.7V MAX/ -5.2V MIN VBB = All pins designated for V BB must be tied together, no external voltage applied. NOTES 1. VBB to be used to supply bias to the AS10515F16MIL only and bypassed (when used) with 0.01 μF to 0.1 μF capacitor. 2. When the input pin with the bubble goes positive, the output goes negative. D IN\\ COUT DOUT VCC2 VCC1 AOUT BOUT AIN\\ DIN CIN CIN\\ VBB VEE BIN\\ BIN AIN LOGIC DIAGRAM 9VBB

Micross Components reserves the right to change products or specifi cations without notice.

  1. R1 = 50 Ω resistor in series with 50 Ω coax constituting the 100 Ω load.
  2. Unused outputs should be loaded 100 Ω to ground.

Figure 1. Switching Test Circuit and Waveforms rise and fall times of 2.0ns ± 0.2ns.

Rev. 2.2 01/10 Micross Components reserves the right to change products or specifi cations without notice. * ELECTRICAL CHARACTERISTICS Each MECL 10K series circuit has been designed to meet the dc specifi cations shown in the test table, after thermal equi- librium has been established. The circuit is in a test socket or mounted on a printed circuit board and transverse air fl ow greater than 500 linear fpm is maintained. Outputs are termi- nated through a 100 Ω resistor to -2.0 volts. QUIESCENT LIMIT TABLE* Connected to pin 9. * Measure voltage on pin 9 while it is connected to other pins. VIH1 VIL1 VIH2 VIL2 PS1 PS2 VEEL VEE VCB Test Voltage Values (Volts)Test Temperature SYMBOL PARAMETER UNITS MIN MAX MIN MAX MIN MAX VIH1 VIL1 VIH2 VIL2 VEE VCC * P.U.T. VOH High Output 11 - 13 2, 3 ,14, 15 VOL Low Output 11 - 13 2, 3 ,14, 15 VOH1 High Output 11 - 13 2, 3 ,14, 15 VOL1 Low Output 11 - 13 2, 3 ,14, 15 VBB Reference 11, 12 9 IEE Power Supply Current -26 -29 -29 mA 8 1, 16 5, 6 11, 12 8 IIH Input Current High 95 165 165 μA 4 - 7 10 - 13 81 , 1 6 4 - 7 10 - 13 ICBO Input Leakage Current -1.0 -1.0 -1.5 μA8 1 , 1 6 4 - 7 10 - 13 4 - 7 10 - 13 LIMITS TEST VOLTAGE APPLIED TO PINS BELOW: Pinouts referenced are for F package, check Pin Assignments VCC = 0V, Output Load = 100 ΩΩΩΩ to -2.0VSubgroup 3Functional Parameters: +25°C Subgroup 1 +125°C Subgroup 2 -55°C

Rev. 2.2 01/10 Micross Components reserves the right to change products or specifi cations without notice. * ELECTRICAL CHARACTERISTICS Each MECL 10K series circuit has been designed to meet the dc specifi cations shown in the test table, after thermal equi- librium has been established. The circuit is in a test socket or mounted on a printed circuit board and transverse air fl ow greater than 500 linear fpm is maintained. Outputs are termi- nated through a 100 Ω resistor to -2.0 volts. QUIESCENT LIMIT TABLE* VIH1 VIL1 VIH2 VIL2 PS1 PS2 VEEL VEE VCB Test Voltage Values (Volts)Test Temperature SYMBOL PARAMETER UNITS MIN MAX MIN MAX MIN MAX VIN VOUT VCC VEEL P.U.T. tPHL Propagation Delay tPLH Propagation Delay Functional Parameters: +25°C Subgroup 9 LIMITS TEST VOLTAGE APPLIED TO PINS BELOW: Pinouts referenced are for F package, check Pin Assignments VCC = 2.0V, Output Load = 100 ΩΩΩΩ to GNDSubgroup 11 +125°C Subgroup 10 -55°C