AS02008MO-R PUIAUDIO | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 5

Technical content

This document contains data proprietary to PUI Audio Inc. Any use or reproduction, in any form, without prior written permission of PUI Audio Inc. is prohibited. ©2019, PUI Audio Inc. PUI Audio, Inc., 3541 Stop Eight Road, Dayton, OH 45414 Tel: (937) 415-5901 Fax: (937) 415-5925 Data Sheet AS02008MO-R Features:

  • IP65-rated design for protection against dust and water
  • Tesa® 4980 double-sided tape for easy installation
  • Great frequency response and sensitivity Speaker Specifications Parameters Values Units Rated Input Power 0.5 Watts Max Input Power 1 Watts Impedance 8 ± 15% Ohms Sensitivity @ 0.5W/0.1M dB Resonant Frequency 750 ± 20% Hz Frequency Range 400 ~ 20,000 Hz Frame Material ABS - Magnet Material NdFeB - Weight 1.32 Grams Ingress Protection Rating IP65 - Acceptable Soldering Methods Hand Solder - Buzz, Rattle, etc. 2V - Environmental Compliances RoHS - Polarity Diaphragm shall move forward when a positive DC signal is applied to positive terminal Storage Temperature -40 to +85 °C Operating Temperature -40 to +85 °C

This document contains data proprietary to PUI Audio Inc. Any use or reproduction, in any form, without prior written permission of PUI Audio Inc. is prohibited. ©2019, PUI Audio Inc. PUI Audio, Inc., 3541 Stop Eight Road, Dayton, OH 45414 Tel: (937) 415-5901 Fax: (937) 415-5925 Measurement Method (Tested with 2V @ 10cm) Typical Frequency Response (2V @ 10cm)

This document contains data proprietary to PUI Audio Inc. Any use or reproduction, in any form, without prior written permission of PUI Audio Inc. is prohibited. ©2019, PUI Audio Inc. PUI Audio, Inc., 3541 Stop Eight Road, Dayton, OH 45414 Tel: (937) 415-5901 Fax: (937) 415-5925 Recommended Soldering Procedure Hand solder using a 25 to 100-watt ESD safe soldering iron with the smallest practical tip. Solder at 350°C ± 20°C (660°F ± 30°F) using lead-free solder for less than 3 seconds per terminal. Reliability Testing Type of Test Test Specifications High Temperature Test Place the speaker in the +85 ± 2 °C chamber for 96 hours, then leave the speaker at room temperature for 1 hour, the SPL should not deviate by ± 3 dB, and resonant frequency should not deviate by ± 50 Hz, compared with pre-test measurement. Low Temperature Test Place the speaker in the −40 ± 2 °C chamber for 96 hours, then leave the speaker at room temperature for 1 hour, the SPL should not deviate by ± 3 dB, and resonant frequency should not deviate by ± 50 Hz, compared with pre-test measurement. Humidity Test After exposure the speaker in the + 40±2 °C, relative humidity 90% ∼ 95% chamber for 96 hours, then leave the speaker at room temperature for 6 hours, the SPL should not deviate by ±3 dB, and resonant frequency should not deviate by ±50 Hz, compare with pre-test measurement. Temperature Cycle Testing Place the speaker in the chamber, temperature cycle setting as below, SPL should not deviate by ± 3 dB, and resonant frequency should not deviate by ± 80 Hz, compare with pre-test measurement. Vibration Test Frequency 30±15 Hz, Amplitude 1.5 mm for 3 Hours. After test, SPL shall not deviate by ±3 dB from pre-test measurement Drop Test 75 cm free falling on concrete floor, 10 times. After test, SPL shall not deviate by ±3 dB from pre-test measurement. Load Test Speaker shall not fail after applying 20 ∼ 20 kHz pink noise with HPF rated power input (RMS), 96 hours. After test, SPL shall not deviate by ±3 dB from pre-test measurement,

This document contains data proprietary to PUI Audio Inc. Any use or reproduction, in any form, without prior written permission of PUI Audio Inc. is prohibited. ©2019, PUI Audio Inc. PUI Audio, Inc., 3541 Stop Eight Road, Dayton, OH 45414 Tel: (937) 415-5901 Fax: (937) 415-5925 Dimensions

This document contains data proprietary to PUI Audio Inc. Any use or reproduction, in any form, without prior written permission of PUI Audio Inc. is prohibited. ©2019, PUI Audio Inc. PUI Audio, Inc., 3541 Stop Eight Road, Dayton, OH 45414 Tel: (937) 415-5901 Fax: (937) 415-5925 Specifications Revisions Revision Description Date - Released from Engineering 5/13/2011 A Revised to Inventor 3D Template 7/15/2013 Note: 1. Unless otherwise specified: A. All dimensions are in millimeters. B. Default tolerances are ±0.5mm and angles are ±3°. 2. Specifications subject to change or withdrawal without notice.