APL3157 ANPEC | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 13
Technical content
Copyright ANPEC Electronics Corp. Rev. A.5 - Aug., 2016 www.anpec.com.tw1 ANPEC reserves the right to make changes to improve reliability or manufacturability without notice, and advise customers to obtain the latest version of relevant information to verify before placing orders. High-Density, +5.5V Capable DPDT Analog Switches APL3157 The APL3157 is a high-density, double-pole/ double- throw (DPDT) analog switch which allows signals from - 0.3V to +5.5V to pass without distortion even when the power supply is below the signal range. The low RON resistance (0.2 Ω ) makes the devices ideal for low-dis- tortion switching, such as audio. The APL3157 has internal shunt switches that discharge the audio amplifier AC-coupling capacitance at the nor- mally open (NO1 and NO2) terminals. This feature re- duces click-and-pop sounds that occur when switching audio signals between precharged points. The switches are fully specified to operate from a single +2.9V to +5.5V power supply. Because of the low supply current requirement, VCC can be provided by a GPIO. When the power is not applied, switches go to a high-imped- ance mode and all analog signal ports can withstand signals from -0.3V to +5.5V. The devices control the switches with a control bit, CB. The APL3157 is available in a 1.2mm x 1.2mm, 0.4mm pitch, 9-bump wafer-level package (WLCSP), and oper- ate over the -4oC to +85oC extended temperature range. Features General Description
Applications
- Smartphones
- Tablets
- Portable Audio/Video Equipment
- Portable Navigation Devices
- – Negative Audio and Video Signal Capable – -0.3V to +5.5V Analog Signal Range Indepen- dent from VCC – On-Resistance 0.2W (typ) – +2.9V to +5.5V Single-Supply Range – Click-and-Pop Suppression
- Smooth Switch Transition – Break-Before-Make Operation
- Low Supply Current 30mA (typ) at 2.9V – Can be Powered by a GPIO – High-Impedance Mode When VCC Not Applied
- ESD Protection on NC_ and NO_ – +15kV Human Body Model
- WLCSP1.2x1.2-9 (1.2mm x 1.2mm) Package
- 40 o C to +85 o C Operating Temperature Range Pin Configuration WLCSP1.2x1.2-9 (Top View) NC1 (A1) NO1 (C1) VCC (C2) NO2 (C3) NC2 (A3) COM2 (B3) COM1 (B1) GND (B2) CB (A2)
Copyright ANPEC Electronics Corp. Rev. A.5 - Aug., 2016 www.anpec.com.tw2 APL3157 Absolute Maximum Ratings (Note 1) Symbol Parameter Rating Unit VCC, CB -0.3 to 6 VSIG NC1, NC2, NO1, NO2, COM1, COM2 <20ns pulse width >20ns pulse width -3~VCC+3V -1~VCC+0.3V V ICC(SIG) Continuous Current NC1, NC2, NO1, NO2, COM1, COM2 -500 to 500 IPEAK(SIG) Peak Current NC1, NC2, NO1, NO2, COM1, COM2 (50% duty cycle) -850 to 850 mA TJ Maximum Junction Temperature 150 TSTG Storage Temperature Range -6 to 150 TS Soldering Temperature Range 260 oC Thermal Characteristics Symbol Parameter Typical Value Unit θJA Junction-to-Ambient Thermal Resistance (Note 2) WLCSP1.2x1.2-9 83 οC/W Note 2 : θJA is measured with the component mounted on a high effective thermal conductivity test board in free air. Ordering and Marking Information Note : ANPEC lead-free products contain molding compounds/die attach materials and 100% matte tin plate termination finish; which are fully compliant with RoHS. ANPEC lead-free products meet or exceed the lead-free requirements of IPC/JEDEC J-STD-020D for MSL classification at lead-free peak reflow temperature. ANPEC defines “Green” to mean lead-free (RoHS compliant) and halogen free (Br or Cl does not exceed 900ppm by weight in homogeneous material and total of Br and Cl does not exceed 1500ppm by weight). Note1: Stresses beyond those listed under "absolute maximum ratings" may cause permanent damage to the device. These are stress ratings only and functional operation of the device at these or any other conditions beyond those indicated under "recom- mended operating conditions" is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. Recommended Operating Conditions (Note3) Symbol Parameter Range Unit VCC Supply Voltage 2.9 ~ 5.5 V Vanalog Analog Signal Range -0.3 ~ 5.5 V TA Ambient Temperature -40 ~ 85 oC TJ Junction Temperature -40 ~ 125 oC Note 3 : Refer to the typical application circuit Package Code Operating Junction Temperature I : -40 to 85 oC Handling Code Assembly Material G : Halogen and Lead Free Device Temperature Range Package Code APL3157 Handling Code Assembly Material TR : Tape & Reel HA : WLCSP1.2x1.2-9 APL3157 HA: X - Date CodeX
Copyright ANPEC Electronics Corp. Rev. A.5 - Aug., 2016 www.anpec.com.tw3 APL3157
Electrical Characteristics
Symbol Parameter Test Conditions Min Typ Max Unit SPOWER SUPPLY VCC Power Supply Range 2.9 - 5.5 V PSRR PSRR RCOM_ = 32Ω , f = 20kHz - 80 - dB VCC = 2.9V, VCB = 0V or VCC - 30 50 µA ICC VCC Supply Current VCC = 4.2V, VCB = 0V or VCC - 35 60 µA ANALOG SWITCH VCC > 2.9V 0 - 5.5 V VNC_, VNO_, VCOM_ Analog Signal Range VCC < 2.9V, RS = 50Ω 0 - 5.5 V RON On-Resistance VCOM_=0V, ICOM_=100mA (Note 3) VCC=3.6V - 0.2 0.3 Ω ΔRON(NC) On-Resistance Match Between Channels VCC = 2.9V, VNC_ = 0V, ICOM_=100mA, between same NC_ and NO_ channel (Note 4) - 0.005 0.05 Ω RFLAT(ON) On-Resistance Flatness VCC=2.9V,ICOM_ = 100mA, VCOM_ = 0V to +5.5V (Notes 5, 6) - 0.001 0.01 Ω VCC=2.9V; open switch; VNO_ or VNC_=0V, +5.5V;VCOM_=+5.5V,0, unconnected -400 - 400 nA INC_(OFF), INO_(OFF) NC_ or NO_ Off-Leakage Current VCC=0V; VNO_ or VNC_=0V, +5.5V; VCOM_=+5.5V, 0V, unconnected -400 - 400 nA ICOM_(OFF) COM_ Off-Leakage Current VCC=0V; VCOM_=+5.5V, 0V; VNO_ or VNC_=0V,+5.5V, unconnected -400 400 nA ICOM_(ON) COM_ On-Leakage Current VCC=2.9V; switch closed; VCOM_=+5.5V, 0V; VNO_ or VNC_=+5.5V, 0V, unconnected -400 400 nA DYNAMIC TIMING tON Turn-On Time VNO_ or VNC_ = 0V, RL = 50Ω , Figure 1a - 5 10 ms tOFF Turn-Off Time VNO_ or VNC_ = 0V, RL = 50Ω , Figure 1a - 1 2.5 ms tBBM Break-Before-Make Time RL = 50Ω , VCC = 3.3V, time for both NC_/NO_ switches are open during transition, Figure 1b (Note 5) 0 5 10 ms Unless otherwise specified, these specifications apply over V IN=5V,VCB=2V and TA= -40 to 85 oC. Typical values are at T A=25oC.
Copyright ANPEC Electronics Corp. Rev. A.5 - Aug., 2016 www.anpec.com.tw4 APL3157 Symbol Parameter Test Conditions Min Typ Max Unit AUDIO PERFORMANCE THD+N Total Harmonic Distortion Plus Noise f = 20Hz to 20kHz, VCOM_ = 0.5VP-P, RS = RL = 50Ω , DC bias = 0V - 0.001 - % VISO Off-Isolation RS = RL = 50Ω , VCOM_=0.5VP-P, f = 100kHz, V CC=0V, DC bias = 0.25V, Figure 2 - -60 - dB Crosstalk RS = RL = 50Ω , VCOM_=0.5VP-P, f = 100kHz, Figure 2 (Note 7) - -80 - dB BW -3dB Bandwidth RS = RL = 50Ω , Figure 2 - 200 - MHz CNC_(OFF) CNO_(OFF) NC_ or NO_ Off-Capacitance VNC_/NO_ = 0.5VP-P, f = 1MHz - 25 - pF CCOM_(ON) COM_ On-Capacitance VNC_/NO_ = 0.5VP-P, f = 1MHz - 50 - pF DIGITAL I/O (CB) VIH Input Logic-High Voltage 1.6 - - V VIL Input Logic-Low Voltage - - 0.4 V IIN Input Leakage Current VCB= 0V or VCC -1 - 1 uA Unless otherwise specified, these specifications apply over V IN=5V,VCB=2V and TA= -40 to 85 oC. Typical values are at T A=25oC. Note2: All specifications are 100% production tested at T A = +25oC, unless otherwise noted. Specifications are over -40 oC to +85oC and are guaranteed by design. Note3: The same limits apply for V COM_= -5.5V to +5.5V and are guaranteed by design. Note4: DRON(MAX) = |RON(CH1) - RON(CH2)|. Note5: Guaranteed by design; not production tested. Note6: Flatness is defined as the difference between the maximum and minimum value of on-resistance, as measured over specified analog signal ranges. Note7: Between two switches.
Copyright ANPEC Electronics Corp. Rev. A.5 - Aug., 2016 www.anpec.com.tw5 APL3157 Typical Operating Characteristics ON-RESISTANCE vs. COM_VOLTAGE ON-RESISTANCE (Ω ) VCOM_ (V) 0 2 3 4 5 60 0.5 0.1 ICOM_=100mA VDD=3V VDD=5V 0.2 0.3 0.4 TUEN-ON/TURN-OFF TIME vs. SUPPLY VOLTAGE TURN-ON/TURN-OFF (ms) SUPPLY VOLTAGE (V) 3 5 5.54.50 43.5 tON tOFF LOGIC THRESHOLD vs. SUPPLY VOLTAGE LOGIC THRESHOLD (V) SUPPLY VOLTAGE (V) 3 5 5.54.543.5 SUPPLY CURRENT vs. LOGIC INPUT VOLTAGE SUPPLY CURRENT(µA) LOGIC INPUT VOLTAGE(V) 0 4 5321 COM_ LEAKAGE CURRENT vs. SUPPLY VOLTAGE LEAKAGE CURRENT (nA) SUPPLY VOLTAGE (V) 3 5 5.54.543.50 100 120 140 160 OFF-ISOLATION(dB) OFF-ISOLATION vs. Frequency Frequency (Hz) 20 100k100 1k 20k-120 -100 -80 -60 -40 -20 AC Test Use Audio Precision With 20kHz AES17 Filter
Copyright ANPEC Electronics Corp. Rev. A.5 - Aug., 2016 www.anpec.com.tw6 APL3157 Typical Operating Characteristics (Cont.) Crosstalk(dB) Crosstalk vs. Frequency Frequency (Hz) 20 100k100 1k 20k -120 -100 -80 -60 -90 -70 -110 THD+N(%) THD+N vs. Frequency 0.0003 0.001 0.002 0.005 0.0005 Frequency (Hz) 20 20k100 1k 10k PSRR vs. Frequency PSRR(dB) -140 -40 -80 -60 -120 -100 Frequency (Hz) 20 20k100 1k 10k
Copyright ANPEC Electronics Corp. Rev. A.5 - Aug., 2016 www.anpec.com.tw7 APL3157 PIN NO. NAME FUNCTION A1 NC1 Normally Closed Terminal for Switch 1 A2 CB Digital Control Input. Drive CB low to connect COM_ to NC_. Drive CB high to connect COM_ to NO_. A3 NC2 Normally Closed Terminal for Switch 2 B1 COM1 Common Terminal for Switch 1 B2 GND Ground B3 COM2 Common Terminal for Switch 2 C1 NO1 Normally Open Terminal for Switch 1 C2 VCC Positive Supply Voltage Input. Bypass VCC to GND with a 0.1 µF capacitor as close as possible to the device. C3 NO2 Normally Open Terminal for Switch 2 Pin Description Block Diagram / Typical Application Circuit CB GND VCC 0.1µF AUDIO CONNECTOR VIDEO AUDIO AMPLIFIER BB GPIO MUIC NC1 NC2 NO2 NO1 COM2 COM1 APL3157
Copyright ANPEC Electronics Corp. Rev. A.5 - Aug., 2016 www.anpec.com.tw9 APL3157
Package Information
WLCSP1.2x1.2-9 PIN 1 D E S Y M B O L MIN. MAX. 0.63 0.12 0.20 0.30 1.10 1.25 0.20 A b D E e MILLIMETERS A2 0.37 0.43
0.40 BSC
WLCSP1.2x1.2-9
0.016 BSC
MIN. MAX. INCHES 0.025 0.005 0.015 0.017 0.008 0.012 0.043 0.049 0.008 1.10 1.25 0.043 0.049 aaa 0.05 BSC 0.002 e e b aaa NX SEATING PLANE A A2 A1
Copyright ANPEC Electronics Corp. Rev. A.5 - Aug., 2016 www.anpec.com.tw10 APL3157 Application A H T1 C d D W E1 F -0.00 13.0+0.50 -0.20 P0 P1 P2 D0 D1 T A0 B0 K0 WLCSP1.5X1.5-9A (mm) Carrier Tape & Reel Dimensions H A d A AB W F T P0OD0 B SECTION B-B SECTION A-A OD1 Devices Per Unit Package Type Unit Quantity WLCSP1.2X1.2-9 Tape & Reel 3000
Copyright ANPEC Electronics Corp. Rev. A.5 - Aug., 2016 www.anpec.com.tw11 APL3157 Taping Dircetion Information WLCSP1.2x1.2-9 USER DIRECTION OF FEED Classification Profile
Copyright ANPEC Electronics Corp. (Tsmax to TP) 3 °C/second max. 3°C/second max. Average ramp-down rate (Tp to Tsmax) 6 °C/second max. 6 °C/second max. Time 25°C to peak temperature 6 minutes max. 8 minutes max.
- Tolerance for peak profile Temperature (Tp) is defined as a supplier minimum and a user maximum.
** Tolerance for time at peak profile temperature (t p) is defined as a supplier minimum and a user maximum. Table 1. SnPb Eutectic Process – Classification Temperatures (Tc) Table 2. Pb-free Process – Classification Temperatures (Tc)
Copyright ANPEC Electronics Corp. Rev. A.5 - Aug., 2016 www.anpec.com.tw13 APL3157 Customer Service Anpec Electronics Corp. Head Office : No.6, Dusing 1st Road, SBIP, Hsin-Chu, Taiwan Tel : 886-3-5642000 Fax : 886-3-5642050 Taipei Branch : 2F, No. 11, Lane 218, Sec 2 Jhongsing Rd., Sindian City, Taipei County 23146, Taiwan Tel : 886-2-2910-3838 Fax : 886-2-2917-3838