APL1086285FC-TRG

APL1086_08 ANPEC | Alldatasheet

Document overview

• Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
• PDF pages: 15

Technical content

Features

Applications

The APL1086 is a low dropout three-terminal adjustable regulators with 1.5A output current capability. In order to obtain lower dropout voltage and faster transient response, which is critical for low voltage applications, the APL1086 has been optimized. The device is available in an adjustable version and fixed output voltages of 1.8V, 2.5V, 2.85V, and 3.3V, the output available voltage range is from 1.25 to 10.7V with an input supply below 12V. Dropout voltage is guaranteed at a maximum of 1.45V at 1.5A. Current limit is trimmed to ensure specified output cur- rent and controlled short-circuit current. On-chip thermal limiting provides protection against any combination of overload that would create excessive junction temperatures. The APL1086 is available in the industry standard 3-pin SOT-223, TO-252, TO-220, or TO-263 power packages.

• Active SCSI Terminators
• Low Voltage Logic Supplies
• Battery-Powered Circuitry
• Post Regulator for Switching Power Supply Simplified Application Circuits * C1 improves ripple rejection. XC should be approximately equal to R1 at ripple frequency * Needed if device is far from filter capacitors R2R11.250VV OUT +×= VIN 10µ F C1* VOUT1 APL1086 OUTIN ADJ + 100µ F 121Ω 1.25V to 10.7V Adjustable Regulator VIN 10µ F APL1086 OUTIN ADJ 121Ω 365Ω VOUT 150µ F 10µ F R2 + Improving Ripple Rejection VIN 10µ F APL1086 OUTIN ADJ TTL 121Ω 365Ω 1k 100µ F 5V Regulator with Shutdown

Copyright  ANPEC Electronics Corp. Rev. A.8 - Dec., 2008 APL1086 www.anpec.com.tw2 Ordering and Marking Information Note: ANPEC lead-free products contain molding compounds/die attach materials and 100% matte tin plate termination finish; which are fully compliant with RoHS. ANPEC lead-free products meet or exceed the lead-free requirements of IPC/JEDEC J-STD-020C for MSL classification at lead-free peak reflow temperature. ANPEC defines “Green” to mean lead-free (RoHS compliant) and halogen free (Br or Cl does not exceed 900ppm by weight in homogeneous material and total of Br and Cl does not exceed 1500ppm by weight). Pin Configurations TAB IS VOUT INOUTADJ/GND 1 2 3 TAB IS VOUT 1 2 3 INOUTADJ/GND Front View for SOT-223 Front View for TO-252

3 VIN

XXXXX25 XXXXX - Date CodeAPL1086- 25V : APL1086 XXXXX33 XXXXX - Date CodeAPL1086- 33V :APL1086 -33F/G/U: APL1086 XXXXX APL1086 -25F/G/U: APL1086XXXXX APL1086 -18F/G/U: APL1086XXXXX - Date CodeXXXXX

18 APL1086

XXXXX18 XXXXX - Date CodeAPL1086- 18V : APL1086 XXXXX285 XXXXX - Date CodeAPL1086- 285V :APL1086 -285F/G/U: APL1086XXXXX 285 APL1086 F/G/U : APL1086 XXXXX XXXXX - Date CodeAPL1086 V : - Date CodeXXXXX - Date CodeXXXXX - Date CodeXXXXX APL1086XXXXX - Date CodeXXXXX Assembly Material Package Code F : TO-220 G : TO-263 U : TO-252 V : SOT-223 Operating Ambient Temperature Range C : 0 to 70 oC Handling Code TU : Tube TR : Tape & Reel Voltage Code 18 : 1.8V 25 : 2.5V 285 : 2.85V 33 : 3.3V Blank : Adjustable Version Assembly Material G : Halogen and Lead Free Device

Copyright  ANPEC Electronics Corp. Rev. A.8 - Dec., 2008 APL1086 www.anpec.com.tw3 Symbol Parameter Rating Unit VI Input Voltage 15 V PD Power Dissipation, TA=25°C SOT-223 TO-252 1.7 W θ JA Thermal Resistance from Junction to Ambient in Free Air SOT-223 TO-252 °C/W TJ Operating Junction Temperature Range 0 to 150 °C TSTG Storage Temperature Range -65 to +150 °C TL Maximum Lead Soldering Temperature, 10 Seconds 260 °C Absolute Maximum Ratings (Note 1,2) Note 1: Stresses beyond the absolute maximum rating may damage the device and operating in the absolute maximum rating conditions may affect device reliability. Note 2: The maximum allowable power dissipation at any T A (ambient temperature) is calculated using: P D (max) = (T J – T A) / θ JA; TJ = 125°C. Exceeding the maximum allowable power dissipation will result in excessive die temperature. APL1086 Symbol Parameter Test Conditions Min. Typ. Max. Unit VREF Reference Voltage 10mA≤ IOUT≤ 1.5A, Output Voltage APL1086-18 TJ =25°C, IOUT =0mA, TJ =0~125°C, 0≤ IOUT≤ 1.5A, 3.5V≤ VIN≤ 9V, 1.782 1.764 1.800 1.800 1.818 1.836 APL1086-25 TJ =25°C, IOUT =0mA, TJ =0~125°C, 0≤ IOUT≤ 1.5A, 4V≤ VIN≤ 9V, 2.475 2.450 2.500 2.500 2.525 2.550 APL1086-28 TJ =25°C, IOUT =0mA, TJ =0~125°C, 0≤ IOUT≤ 1.5A, 4.25V≤ VIN≤ 9V, 2.822 2.792 2.850 2.850 2.878 2.910 VOUT APL1086-33 TJ =25°C, IOUT =0mA, TJ =0~125°C, 0≤ IOUT≤ 1.5A, 4.75V≤ VIN≤ 9V, 3.267 3.235 3.3003. 300 3.333 3.365 V Line Regulation APL1086 TJ =0~125°C IOUT=10mA, 1.5V≤ VIN – VOUT≤ 9V (Note3) - 0.03 0.2 APL1086-18 IOUT=0mA, 3.5V≤ VIN≤ 9V (Note3) - 1 6 APL1086-25 IOUT=0A, 4V≤ VIN≤ 9V (Note3) - 1 6 APL1086-28 IOUT=0A, 4.25V≤ VIN ≤ 9V (Note3) - 1 6 REGLINE APL1086-33 IOUT=0A, 4.75V≤ VIN≤ 9V (Note3) - 1 6 mV Load Regulation APL1086 TJ =0~125°C (VIN -VOUT)=3V, 0≤ IOUT ≤ 1.5A (Note3) - 0.1 0.4 APL1086-18 VIN =3.5V, 0≤ IOUT ≤ 1.5A (Note3) - 1 10 APL1086-25 VIN =4V, 0≤ IOUT ≤ 1.5A (Note3) - 1 10 APL1086-28 VIN =4.25V, 0≤ IOUT≤ 1.5A (Note3) - 1 10 REGLOAD APL1086-33 VIN =4.75V, 0≤ IOUT ≤ 1.5A (Note3) - 1 10 mV

Electrical Characteristics

Copyright  ANPEC Electronics Corp. Rev. A.8 - Dec., 2008 APL1086 www.anpec.com.tw4 Electrical Characteristics (Cont.) APL1086 Symbol Parameter Test Conditions Min. Typ. Max. Unit VD Dropout Voltage IOUT=1.5A ,TJ =0~125°C (Note4) - 1.3 1.45 V ILIMIT Current Limit (VIN -VOUT)=5V, TJ =25°C 1500 - - mA IADJ Adjust Pin Current (VIN -VOUT)=3V, IOUT=10mA, TJ =0~125°C - 60 120 µA Δ IADJ Adjust Pin Current Change TJ=0~125°C, 10mA≤ IOUT ≤ 1.5A, 1.4V≤ ( VIN -VOUT) ≤ 7.75V - 0.2 5 µA IO Minimum Load Current TJ =0~125°C, (VIN -VOUT)=7.75V, (Note 5) - 1.7 - mA PSRR Ripple Rejection FRIPPLE=120Hz, VRIPPLE=1VP-P, (VIN -VOUT)=3V, TJ =0~125°C 60 75 - dB TR Thermal Regulation TJ =25°C, 30ms Pulse - 0.01 0.02 %/ W TS Temperature Stability - 0.5 - % LS Long -Term Stability TJ =125°C,1000Hrs. - 0.3 - % VN RMS Output Noise TJ=25°C,10Hz≤ F≤ 10kHz, (% of VOUT) - 0.003 - % at Tab, SOT-223 - 15 - θ JC Thermal Resistance from Junction to Case at Tab, TO-252 - 6 - °C/ W OT Over Temperature Point - 150 - °C Quiescent Current APL1086-18 TJ=0~125°C, VIN≤ 9V - 5.5 APL1086-25 VIN≤ 9V - 5.5 10 APL1086-28 VIN≤ 9V - 5.5 10 APL1086-33 VIN≤ 9V - 5.5 10 mA Note 3: See thermal regulation specifications for changes in output voltage due to heating effects. Load line regulations are measured at a constant junction temperature by low duty cycle pulse testing. Note 4: Dropout voltage is specified over the full output current range of the device. Dropout voltage is defined as the minimum input/ output differential measured at the specified output current. Test points and limits are also shown on the Dropout Voltage curve. Note 5: Minimum load current is defined as the minimum output current required to maintain regulation.

Copyright  ANPEC Electronics Corp. Rev. A.8 - Dec., 2008 APL1086 www.anpec.com.tw5 Dropout Voltage vs. Output Current Output Voltage vs. Input Voltage Output Current (A) Input Voltage (V) Load Transient Response Output Current (A) Output Voltage Deviation (V) Time (µs) Line Transient Response Input Voltage (V) Output Voltage Deviation (V) Time (µs) Dropout Voltage (V) Output Voltage (V) Typical Operating Characteristics 0 0.5 1 1.5 0.9 0.95 1.05 1.1 1.15 1.2 1.25 1.3 1.35 0 1 2 3 4 5 6 7 8 9 0.5 1.5 2.5 3.5 -20 30 80 130 180 -0.05 0.05 0.1 0.15 CIN=10µF Cout=10µF Tantalum IOUT=0.1A 100 0 100 200 300 400 500 600 700 800 900 -0.03 -0.02 -0.01 0.01 0.02 0.5 1.5 2.5 3.5 4.5 CIN=10µF Cout=10µF Tantalum VIN=5V

Copyright  ANPEC Electronics Corp. Rev. A.8 - Dec., 2008 APL1086 www.anpec.com.tw6 Current Limit vs. Input Voltage Output Voltage vs. Temperature Temperature (°C) Input Voltage (V) Typical Operating Characteristics (Cont.) Output Voltage (V) Input Current vs. Input Voltage Input Voltage (V) Input Current (mA) Current Limit (A) Output Voltage vs. Temperature Output Voltage (V) Temperature (°C) 0 3 6 9 12 0.9 1.4 1.9 2.4 2.9 3.4 0 2 4 6 8 10 2.7 2.8 3.1 3.2 3.3 3.4 3.0 2.9 -50 -25 0 25 50 75 100 125 Vout=1.25V 1.6 1.7 1.8 1.9 2.1 2.2 2.3 2.4 2.5 2.6 -50 -25 0 25 50 75 100 125

Copyright  ANPEC Electronics Corp. Rev. A.8 - Dec., 2008 APL1086 www.anpec.com.tw7 Current Limit vs. Temperature Temperature (°C) Current Limit (mA) Adjustable Pin Current (µA) Input Current (mA) Temperature (°C) Temperature (°C) Adjustable Pin Current vs. Temperature Input Current vs. Temperature Typical Operating Characteristics (Cont.) -50 0 50 100 125-25 25 75 -50 0 50 100 125-25 25 75 1.5 1.7 1.9 2.1 2.3 2.5 2.7 2.9 -50 -30 -10 10 30 50 70 90 110 130 150 Vin-Vout=5V

Copyright  ANPEC Electronics Corp. Rev. A.8 - Dec., 2008 APL1086 www.anpec.com.tw8

Package Information

A VIEW A 0.25L GAUGE PLANE SEATING PLANE D E e SEE VIEW A c b SYMBOL MIN. MAX. 1.80 0.02 0.66 0.84 2.90 3.10 0.23 0.33 0.10 6.70 A b c D E e MILLIMETERS A2 1.50 1.70

2.30 BSC

3.30 3.70 6.30 6.70 7.30

0.091 BSC

MIN. MAX. INCHES 0.071 0.001 0.059 0.067 0.026 0.033 0.114 0.122 0.009 0.013 0.264 0.130 0.146 0.248 0.264 0.287 0.004 L 0.75 0.030 e1 4.60 BSC 0.181 BSC °10°0 °10°0 Note : 1. Follow from JEDEC TO-261 AA. 2. Dimension D and E1 are determined at the outermost extremes of the plastic exclusive of mold flash, tie bar burrs, gate burrs, and interlead flash, but including any mismatch between the top and bottom of the plastic body.

Copyright  ANPEC Electronics Corp. Rev. A.8 - Dec., 2008 APL1086 www.anpec.com.tw9 SYMBOL MIN. MAX. 2.39 4.95 5.46 0.46 0.61 0.13 5.33 A c D E MILLIMETERS b 0.50 0.89

2.29 BSC

4.57 6.35 6.73 6.22

0.090 BSC

MIN. MAX. INCHES 0.094 0.020 0.035 0.195 0.215 0.018 0.024 0.210 0.180 0.250 0.265 2.18 0.245 0.086 0.005 0.035 0.070 0.410 H L e 9.40 0.90 0.46 0.89 1.78 10.41 0.370 0.035 0.018 0.040L4 1.02 0.1503.81 0.89 2.03 0.035 0.080 8°0° 8°0° 0.25 GAUGE PLANE L VIEW A SEATING PLANE L4 L3D E e H A SEE VIEW A b c 6.00 Note : Follow JEDEC TO-252 . 6.00 0.236 0.236

Copyright  ANPEC Electronics Corp. Rev. A.8 - Dec., 2008 APL1086 www.anpec.com.tw10 L e P Q D A c b E/2 E SYMBOL MIN. MAX. 4.83 0.51 1.14 1.78 0.36 0.61 14.22 16.51 1.40 12.19 A c D E MILLIMETERS b 0.38 1.02

2.54 BSC

9.65 10.67 6.86

0.100 BSC

MIN. MAX. INCHES 0.190 0.020 0.015 0.040 0.045 0.070 0.014 0.024 0.560 0.650 0.480 0.380 0.420 0.270 3.56 0.140 0.055 0.355 0.250 0.580 P L e 12.70 8.38 9.02 6.35 14.73 0.500 0.330 Q H1 5.84 6.86 0.230 0.270 4.09 0.161 2.03A2 2.92 0.080 0.115 E2 0.76 0.030 12.88 0.507 0.3508.89 3.53 0.139 2.54 3.43 0.100 0.135 Note: Follow JEDEC TO-220 AB.

Copyright  ANPEC Electronics Corp. Rev. A.8 - Dec., 2008 APL1086 www.anpec.com.tw11 L VIEW A 0.25 GAUGE PLANE SEATING PLANE SEE VIEW A E H D L1 A b c YM B OL MIN. MAX. 4.83 0.00 1.14 1.78 0.38 0.74 1.14 1.65 0.25 6.00 c D E MILLIMETERS b 0.51 0.99 9.65 11.43 6.22 MIN. MAX. INCHES 0.190 0.000 0.020 0.039 0.045 0.070 0.015 0.029 0.045 0.065 0.236 0.380 0.450 0.245 4.06 0.160 0.010 0.380 0.066 0.110 L e 1.78 8.38 9.65 1.68 2.79 0.070 0.330 H 14.61 15.88 0.575 0.625 1.78 0.070 9.00 9.00 0.354 0.354 Note : Follow JEDEC TO-263 AB. S A 0 808θ o o o o

Copyright  ANPEC Electronics Corp. Rev. A.8 - Dec., 2008 APL1086 www.anpec.com.tw12 Application A H T1 C d D W E1 F -0.00 13.0+0.50 -0.20 P0 P1 P2 D0 D1 T A0 B0 K0 TO-263 Application A H T1 C d D W E1 F -0.00 13.0+0.50 -0.20 P0 P1 P2 D0 D1 T A0 B0 K0 TO-252 Application A H T1 C d D W E1 F -0.00 13.0+0.50 -0.20 P0 P1 P2 D0 D1 T A0 B0 K0 SOT-223 Carrier Tape & Reel Dimensions A AB W F T P0OD0 B SECTION B-B SECTION A-A OD1 H A d (mm)

Copyright  ANPEC Electronics Corp. Rev. A.8 - Dec., 2008 APL1086 www.anpec.com.tw13 Package Type Unit Quantity TO-263 Tape & Reel 800 TO-252 Tape & Reel 2500 SOT-223 Tape & Reel 2500 Devices Per Unit Taping Direction Information TO-263 TO-252 SOT-223 USER DIRECTION OF FEED USER DIRECTION OF FEED USER DIRECTION OF FEED

Copyright  ANPEC Electronics Corp. Rev. A.8 - Dec., 2008 APL1086 www.anpec.com.tw14 t 25 C to Peak tp Ramp-up tL Ramp-down ts Preheat Tsmax Tsmin TL TP Temperature Time Critical Zone TL to T P Reflow Condition (IR/Convection or VPR Reflow) Test item Method Description SOLDERABILITY MIL-STD-883D-2003 245°C, 5 sec HOLT MIL-STD-883D-1005.7 1000 Hrs Bias @125°C PCT JESD-22-B,A102 168 Hrs, 100%RH, 121°C TST MIL-STD-883D-1011.9 -65°C~150°C, 200 Cycles ESD MIL-STD-883D-3015.7 VHBM > 2KV, VMM > 200V Latch-Up JESD 78 10ms, 1tr > 100mA Reliability Test Program Profile Feature Sn-Pb Eutectic Assembly Pb-Free Assembly Average ramp-up rate (TL to TP) 3°C/second max. 3°C/second max. Preheat - Temperature Min (Tsmin) - Temperature Max (Tsmax) - Time (min to max) (ts) 100°C 150°C 60-120 seconds 150°C 200°C 60-180 seconds Time maintained above: - Temperature (TL) - Time (tL) 183°C 60-150 seconds 217°C 60-150 seconds Peak/Classification Temperature (Tp) See table 1 See table 2 Time within 5°C of actual Peak Temperature (tp) 10-30 seconds 20-40 seconds Ramp-down Rate 6°C/second max. 6°C/second max. Time 25°C to Peak Temperature 6 minutes max. 8 minutes max. Notes: All temperatures refer to topside of the package. Measured on the body surface. Classification Reflow Profiles

Copyright  ANPEC Electronics Corp. Table 2. Pb-free Process – Package Classification Reflow Temperatures Table 1. SnPb Eutectic Process – Package Peak Reflow Temperatures Sindian City, Taipei County 23146, Taiwan, R. O. C.