APA7063

APA7063 ANPEC | Alldatasheet

Document overview

• Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
• PDF pages: 20

Technical content

Copyright  ANPEC Electronics Corp. Rev. A.5 - Mar., 2003 APA7063 www.anpec.com.tw1 ANPEC reserves the right to make changes to improve reliability or manufacturability without notice, and advise customers to obtain the latest version of relevant information to verify before placing orders. Stereo 1.5W Audio Power Amplifier with DC Volume Control Features General Description

Applications

• •••• Operating Voltage: 3.3V to 5V
• •••• DC Volume Control Interface, 0dB to –105dB
• •••• Depop Circuitry Integrated
• •••• Thermal shutdown protection circuitry
• •••• High supply voltage ripple rejection
• •••• Low Supply Current, IDD = 13mA at Stereo BTL
• •••• Low Shutdown Current, IDD = 0.7µA
• •••• Bridge-Tied Load (BTL) or Single-Ended-(SE) Modes Operation
• •••• Output Power at 1% THD+N, VDD=5V -1.2 W/Ch (typ) into an 8Ω Load
• •••• Output Power at 10% THD+N, VDD=5V -1.5 W/Ch (typ) into an 8Ω Load
• •••• Low Crossover Distortion
• •••• Low Quiescent Current
• •••• Bridge-tied or Stereo(Single-ended) Configura- tions
• ••••/G20 Portable and Desktop Computers
• ••••/G20/G20 Multimedia Monitors
• ••••/G20/G20 Portable Radios, PDAs, and Portable TVs The APA7063 is a monolithic integrated circuit that pro- vides DC volume control, and a stereo bridged audio power amplifiers capable of producing 1.5W(1.2W) into 8Ω with less than 10%(1.0%) THD+N. APA7063 pro- vides a volume control pin DC_Vol determines the at- tenuation of output of the amplifiers. The attenuator range is from 0dB (DC_Vol=0.7VDD) to –105dB (DC_Vol=0V) with 32 steps. Both of the depop circuitry and the thermal shutdown protection circuitry are integrated in the APA7063, that reduces pops and clicks noise during power up and when using the shutdown modes and protects the chip from being destroyed by over temperature failure. To simplify the audio system design applications, the APA7063 combines a stereo bridge-tied loads (BTL) mode for speaker drive and a stereo single-end (SE) mode for headphone drive into a single chip, where both modes are easily switched by the SE/BTL input control pin signal. The APA7063 also features a shutdown func- tion which keeps the supply current only 0.7µA (typ). SHUTDOWN VCC - OUT2 + OUT2 Vo1 DC Vol Vin1 + OUT1 VCC - OUT1 Bypass SE/BTL GND Vin2 Vo2 V CC Pin Description

Copyright  ANPEC Electronics Corp. Rev. A.5 - Mar., 2003 APA7063 www.anpec.com.tw2 APA7063 Package Code J : PDIP - 16 K : SOP - 16 Temp. Range I : - 40 to 85 C Handling Code TU : Tube TR : Tape & Reel Handling Code Temp. Range Package Code APA7063 J : APA7063 XXXXX XXXXX - Date Code APA7063 K : APA7063 XXXXX XXXXX - Date Code Block Diagram (Over operating free-air temperature range unless otherwise noted.) Symbol Parameter Rating Unit VDD Supply Voltage 6 V TA Operating Ambient Temperature Range -40 to 85 °C TJ Maximum Junction Temperature 150 °C TSTG Storage Temperature Range -65 to +150 °C TS Soldering Temperature,10 seconds 260 °C VESD Electrostatic Discharge -2000 to 2000* 1 V Absolute Maximum Ratings Volume Control 32 steps Power Management Click and Pop Suppression Circuitry Shutdown VCC GND Bypass Bias Vin2 10KΩ10KΩ 20KΩ20KΩ + OUT1 10KΩ 20KΩ20KΩ 10KΩ Vo2 Vin1 Vo1 - OUT1 - OUT2 + OUT2 SE/BTL Ordering and Marking Information

Copyright  ANPEC Electronics Corp. Rev. A.5 - Mar., 2003 APA7063 www.anpec.com.tw3 Electical Characteristics Electrical Characteristics for Entire IC The following specifications apply for V DD= 5V unless otherwise noted. Limits apply for T A= 25°C APA7063Symbol Parameter Test Conditions Min. Typ. Max. Unit VDD Supply Voltage 3.3 5.5 V IDD Quiescent Power Supply Current VIN=0V, IO=0A 13 25 mA ISD Shutdown Current V PIN 2= VDD 0.7 2.0 µA VIH SE/BTL High Input Voltage 4 V VIL SE/BTL Low Input Voltage 0.8 V Electrical Characteristics for Volume Attenuators The following specifications apply for V DD= 5V. Limits apply for T A= 25°C APA7063Symbol Parameter Test Conditions Min. Typ. Max. Unit Gain with V pIN 3=5V ±0.5CRANGE Attenuator Range Attenuation with V pIN 3=0V -100 -105 dB Electrical Characteristics for BTL Mode Operation The following specifications apply for VDD= 5V unless otherwise noted. Limits apply for TA= 25°C APA7063 UnitSymbol Parameter Test Conditions Typ. VOS Output Offset Voltage V IN=0V 5 mV THD=1%, f=1kHz RL=8Ω 1.2 PO Output Power THD=10%, f=1kHz RL=8Ω 1.5 W AVD=2, 20Hz<f<20kHz, R L=8Ω , PO =1W THD+N Total Harmonic Distortion + Noise PO =340mW, RL=32Ω , 0.3 1.0 RSRR Power Supply Rejection Ratio VRIPPLE=200mV Rms , RL=8Ω CB=2.2µF, f=120Hz 74 dB XTALK Channel Separation f=1kHz , C B=2.2µF 95 dB VN Output Noise Voltage RL=8Ω ,A-Wtd Filter 40 uV

Copyright  ANPEC Electronics Corp. Rev. A.5 - Mar., 2003 APA7063 www.anpec.com.tw4 Electical Characteristics (Cont.) Electrical Characteristics for SE Mode Operation The following specifications apply for V DD= 5V unless otherwise noted. Limits apply for T A= 25°C APA7063Symbol Parameter Test Conditions Typ. Unit VDS Output Offset Voltage V IN=0V, 100 mV PO Output Power THD=1%, f=1KHZ, RL=32KΩ THD=10%, f=1KHZ, RL=32K Ω 100 mW AV= 1,VOUT=1 VRMS, f=1KHZ, RL=1K Ω 0.01 /G25THD+N Total Harmonic Distortion plus Noise PO= 75mW, RL=32KΩ , Av=1, f=1KHZ 0.05 /G25 RSRR Power Supply Rejection Ratio VRIPPLE= 200mVRMS, f=120Hz,CB=2.2µF 58 dB XTALK Channel Separation f=1KHZ, CB=2.2µF 95 dB VN Output Noise Voltage RL=1KΩ , A-Wtd Filter 30 uV Pin Name No I/O Description Shutdown 1 1 Shutdown mode control signal input, place entire IC in shutdown mode when held high, Idd=0.7uA. VDD 2,10,15 Supply voltage input pin. DC_Vol 3 I Volume control function input pin. Vo1 4 O Channel 1 output for external feedback circuit. Vin1 5 I Audio input channel 1 Vin2 6 I Audio input channel 2 Vo2 7 O Channel 2 output for external feedback circuit. GND 8 Ground connection for circuitry. +OUT2 9 O Channel 2 positive output in BTL mode and high impedance state in SE mode. -OUT2 11 O Channel 2 negative output in BTL mode and in SE mode. SE/BTL 12 I Mode control signal input, hold low for BTL mode, hold high for SE mode. Bypass 13 I Connect to voltage divider for internal mid_supply bias -OUT2 14 O Channel 1 negative output in BTL mode and in SE mode. +OUT1 16 O Channel 1 positive output in BTL mode and high impedance state in SE mode. Pin Description

Copyright  ANPEC Electronics Corp. Rev. A.5 - Mar., 2003 APA7063 www.anpec.com.tw5 Typical Application Circuit /G53/G68/G75/G74/G64/G6F/G77/G6E/G20/G20/G20/G20/G20/G20/G2B/G4F/G55/G54/G31 /G56/G43/G43/G20/G20/G20/G20/G20/G20/G20/G20/G20/G20/G20/G20/G20/G20/G20/G20/G20/G20/G56/G43/G43 /G44/G43/G5F/G56/G6F/G6C/G20/G20/G20/G20/G20/G20/G20/G20/G20/G20/G2D/G4F/G55/G54/G31 /G56/G6F/G31/G20/G20/G20/G20/G20/G20/G20/G20/G20/G20/G20/G20/G20/G20/G56/G62/G79/G70/G61/G73/G73 /G56/G69/G31/G20/G20/G20/G20/G20/G20/G20/G20/G20/G20/G20/G20/G20/G20/G53/G45/G2F/G42/G54/G4C /G56/G69/G32/G20/G20/G20/G20/G20/G20/G20/G20/G20/G20/G20/G20/G20/G20/G20/G2D/G4F/G55/G54/G32 /G56/G6F/G32/G20/G20/G20/G20/G20/G20/G20/G20/G20/G20/G20/G20/G20/G20/G20/G20/G20/G20/G56/G43/G43 /G47/G4E/G44/G20/G20/G20/G20/G20/G20/G20/G20/G20/G20/G20/G20/G20/G20/G2B/G4F/G55/G54/G32 R-in L-in /G52/G2D/G63/G68 Headphone jack/G4C/G2D/G63/G68 /G35/G56 /G35/G56 /G31µµµµ/G46 /G31µµµµ/G46 /G32/G30/G6BΩΩΩΩ /G32/G30/G6BΩΩΩΩ /G32/G30/G6BΩΩΩΩ /G32/G30/G6BΩΩΩΩ /G31/G30/G30/G6BΩΩΩΩ /G31/G30/G30/G6BΩΩΩΩ /G31/G6BΩΩΩΩ /G31/G6BΩΩΩΩ /G32/G32/G30µµµµ/G46 /G32/G32/G30µµµµ/G46 APA7063 R_var 1µF r*=R_var/50 * Add a resistor to avoid volume control gain error at power on status. For the R_var with 10K Ω variable resistor, the recommended value of r is in range of 100~200 Ω .

Copyright  ANPEC Electronics Corp. Rev. A.5 - Mar., 2003 APA7063 www.anpec.com.tw6 0.01 0.02 0.05 0.1 0.2 0.5 20 20k50 100 200 500 1k 2k 5k 10k 0.01 0.02 0.05 0.1 0.2 0.5 20 20k50 100 200 500 1k 2k 5k 10k Frequency (Hz)Frequency (Hz) AV=2 AV=8 AV=4AV=2AV=8 AV=4 VDD=5V RL=8Ω Po=1.0W BTL VDD=5V RL=16Ω Po=0.5W BTL THD+N-Total Harmonic Distortion+Noise (%) THD+N-Total Harmonic Distortion+Noise (%) Typical Characteristics 0.01 0.02 0.05 0.1 0.2 0.5 10m 120m 50m 100m 200m 500m 0.01 0.02 0.05 0.1 0.2 0.5 10m 220m 50m 100m 200m 500m 1 Output Power (W)Output Power (W) f=20kHz f=20Hz f=1kHz f=20kHz f=20Hz f=1kHz VDD=5V RL=8Ω BTL VDD=5V RL=16Ω BTL THD+N-Total Harmonic Distortion+Noise (%) THD+N-Total Harmonic Distortion+Noise (%)

Copyright  ANPEC Electronics Corp. Rev. A.5 - Mar., 2003 APA7063 www.anpec.com.tw7 0.001 0.002 0.005 0.01 0.02 0.05 0.1 0.5 20 20k50 100 200 500 1k 2k 5k 10k 0.01 0.02 0.05 0.1 0.2 0.5 20 20k50 100 200 500 1k 2k 5k 10k 0.01 0.02 0.05 0.1 0.2 0.5 10m 500m20m 30m 50m 70m 200m20 20k50 100 200 500 1k 2k 5k 10k 0.001 0.002 0.005 0.01 0.02 0.05 0.1 0.5 Output Power (W)Froquency (Hz) Frequency (Hz)Frequency (Hz) f=20kHz f=1kHz f=20Hz AV=4 AV=1 AV=2 AV=4 AV=1 AV=2 AV=4 AV=1 AV=2 VDD=5V RL=8Ω Po=0.25W SE VDD=5V RL=32Ω Po=75mW SE VDD=5V RL=10kΩ Vin=1Vrms SE VDD=5V RL=8Ω SE THD+N-Total Harmonic Distortion+Noise (%) THD+N-Total Harmonic Distortion+Noise (%) THD+N-Total Harmonic Distortion+Noise (%) THD+N-Total Harmonic Distortion+Noise (%) Typical Characteristics (Cont.)

Copyright  ANPEC Electronics Corp. Rev. A.5 - Mar., 2003 APA7063 www.anpec.com.tw8 0.001 0.002 0.005 0.01 0.02 0.05 0.1 0.5 100m 3200m 300m 500m 800m1 2 0.001 0.002 0.005 0.01 0.02 0.05 0.1 0.5 10m 200m20m 30m 50m 70m 100m Output Voltage (V)Output Power (W)) f=20kHz f=1kHz f=20Hz f=20kHz f=1kHz f=20Hz VDD=5V RL=32Ω SE VDD=5V RL=10kΩ SE THD+N-Total Harmonic Distortion+Noise (%) THD+N-Total Harmonic Distortion+Noise (%) Typical Characteristics (Cont.) 0.01 0.02 0.05 0.1 0.2 0.5 20 20k50 100 200 500 1k 2k 5k 10k Frequency (Hz) AV=2 AV=8 VDD=3.3V RL=8Ω Po=0.4W BTL THD+N-Total Harmonic Distortion+Noise (%) 0.01 0.02 0.05 0.1 0.2 0.5 20 20k50 100 200 500 1k 2k 5k 10k Output Power (W) AV=2 AV=4 AV=8 VDD=3.3V RL=16Ω Po=0.2W BTL THD+N-Total Harmonic Distortion+Noise (%)

Copyright  ANPEC Electronics Corp. Rev. A.5 - Mar., 2003 APA7063 www.anpec.com.tw9 0.01 0.02 0.05 0.1 0.2 0.5 10m 500m20m 30m 50m 70m 200m 0.01 0.02 0.05 0.1 0.2 0.5 10m 800m20m 30m 50m 80m 200m 400m Output Power (W)Output Power (W) f=20kHz f=1kHz f=20Hz f=20kHz f=1kHz f=20Hz VDD=3.3V RL=8Ω BTL VDD=3.3V RL=16Ω BTL THD+N-Total Harmonic Distortion+Noise (%) THD+N-Total Harmonic Distortion+Noise (%) Typical Characteristics (Cont.) 0.01 0.02 0.05 0.1 0.2 0.5 20 20k50 100 200 500 1k 2k 5k 10k 0.01 0.02 0.05 0.1 0.2 0.5 20 20k50 100 200 500 1k 2k 5k 10k Frequency (Hz)Frequency (Hz) AV=4 AV=2 AV=1 AV=4 AV=2 AV=1 VDD=3.3V RL=8Ω Po=100mW SE VDD=3.3V RL=32Ω Po=35mW SE THD+N-Total Harmonic Distortion+Noise (%) THD+N-Total Harmonic Distortion+Noise (%)

Copyright  ANPEC Electronics Corp. Rev. A.5 - Mar., 2003 APA7063 www.anpec.com.tw10 0.01 0.02 0.05 0.1 0.2 0.5 10m 200m20m 30m 50m 70m 100m 0.01 0.02 0.05 0.1 0.2 0.5 20 20k50 100 200 500 1k 2k 5k 10k Output Power (W)Frequency (Hz) f=20kHz f=1kHz f=20Hz AV=4 AV=2 AV=1 VDD=3.3V RL=10kΩ Vin=1Vp SE VDD=3.3V RL=8Ω SE THD+N-Total Harmonic Distortion+Noise (%) THD+N-Total Harmonic Distortion+Noise (%) Typical Characteristics (Cont.) 0.01 0.02 0.05 0.1 0.2 0.5 100m 2200m 300m 500m 700m 1 0.01 0.02 0.05 0.1 0.2 0.5 10m 55m12m 15m 20m 25m 30m 35m 42m Output Voltage (V)Output Power (W) f=20kHz f=1kHz f=20Hz f=20kHz f=1kHz f=20Hz VDD=3.3V RL=32Ω SE VDD=3.3V RL=10kΩ SE THD+N-Total Harmonic Distortion+Noise (%) THD+N-Total Harmonic Distortion+Noise (%)

Copyright  ANPEC Electronics Corp. Rev. A.5 - Mar., 2003 APA7063 www.anpec.com.tw11 0.006 0.02 0.05 0.1 0.2 0.5 100m 2200m 300m 500m 700m 1 0.001 0.002 0.005 0.01 0.02 0.05 0.1 0.5 100m 3200m 300m 500m 800m1 2 Output Voltage (V) Output Voltage (V) f=20kHz f=1kHz f=20Hz f=20kHz f=1kHz f=20Hz VDD=5V RL=10kΩ docking VDD=3.3V RL=10kΩ docking THD+N-Total Harmonic Distortion+Noise (%) THD+N-Total Harmonic Distortion+Noise (%) Typical Characteristics (Cont.) 100u 10u 20u 50u 20 20k50 100 200 500 1k 2k 5k 10k 100u 10u 20u 50u 20 20k50 100 200 500 1k 2k 5k 10k Frequency (Hz) Frequency (Hz) VDD=5V RL=8Ω Av=2V/V BTL A_wtd filter No filter VDD=5V RL=10kΩ Av=1V/V SE A_wtd filter No filter VN-Output Noise Voltage( V) VN-Output Noise Voltage( V)

Copyright  ANPEC Electronics Corp. Rev. A.5 - Mar., 2003 APA7063 www.anpec.com.tw12 -120 -100 -80 -60 -40 -20 20 20k50 100 200 500 1k 2k 5k 10k Crosstalk (dB) -120 -100 -80 -60 -40 -20 20 20k50 100 200 500 1k 2k 5k 10k Crosstalk (dB) Frequency (Hz) Frequency (Hz) f=20kHz f=1kHz VDD=5V RL=8Ω Po=1W Av=2V/V BTL VDD=5V RL=32Ω Po=75mW Av=1V/V SE f=20kHz f=1kHz Typical Characteristics (Cont.) +12 +10 20 20k50 100 200 500 1k 2k 5k 10k Gain (dBV) Frequency (Hz) Cf=0.068µF Cf=0.22µF Cf=0.1µF VDD=5V RL=8Ω Av=2V/V BTL 0.1 0.2 0.3 0.4 0.5 0.6 0.7 PD-Power Disspation (W) Output Power (W) RL=16Ω RL=32Ω RL=8Ω VDD=5V THD<1% BTL

Copyright  ANPEC Electronics Corp. Rev. A.5 - Mar., 2003 APA7063 www.anpec.com.tw13 0.02 0.04 0.06 0.08 0.1 0.12 0.14 0.16 0.18 0.2 PD-Power Disspation (W) Output Power (W) RL=16Ω RL=32Ω RL=8Ω VDD=5V THD<1% SE Typical Characteristics (Cont.) 0.2 0.4 0.6 0.8 1.2 1.4 1.6 1.8 2.5 3 3.5 4 4.5 5 5.5 2.5 7.5 12.5 17.5 IDD-Supply Current (mA) VDD-Supply Voltage (V) VDD-Supply Voltage (V) Output Power (W) THD=10% THD=1% BTL SE No Load VDD=5V RL=8Ω BTL 0.02 0.04 0.06 0.08 0.1 0.12 0.14 0.16 2.5 3 3.5 4 4.5 5 5.5 VDD-Supply Voltage (V) Output Power (W) THD=10% THD=1% VDD=5V RL=32Ω SE

Copyright  ANPEC Electronics Corp. Rev. A.5 - Mar., 2003 APA7063 www.anpec.com.tw14 0.5 1.5 2.5 4 8 12 16 20 24 28 32 36 40 44 48 52 56 60 64 Output Power (W) Load Resistance (Ω ) THD=10% THD=1% VDD=5V BTL Typical Characteristics (Cont.) 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.1 4 8 12 16 20 24 28 32 36 40 44 48 52 56 60 64 Output Power (W) Load Resistance (Ω ) THD=10% THD=1% VDD=3.3V BTL 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 4 8 12 16 20 24 28 32 36 40 44 48 52 56 60 64 Output Power (W) Load Resistance (Ω ) THD=10% THD=1% VDD=5V SE 0.02 0.04 0.06 0.08 0.1 0.12 0.14 0.16 0.18 0.2 0.22 0.24 0.26 0.28 0.3 0.32 0.34 4 8 12 16 20 24 28 32 36 40 44 48 52 56 60 64 Output Power (W) Load Resistance (Ω ) THD=10% THD=1% VDD=3.3V SE

Copyright  ANPEC Electronics Corp. Rev. A.5 - Mar., 2003 APA7063 www.anpec.com.tw15 -120 -100 -80 -60 -40 -20 Gsin (dBV) Voltage (V) VDD=5V SE Typical Characteristics (Cont.) PRSS (dBgA) Frequency (Hz) -80 -70 -60 -50 -40 -30 -20 -10 20 20k50 100 200 500 1k 2k 5k VDD=5V Vin=200mVp RL=8Ω Cb=2.2µF SE/BTL

Copyright  ANPEC Electronics Corp. Rev. A.5 - Mar., 2003 APA7063 www.anpec.com.tw16 SO – 300mil ( Reference JEDEC Registration MS-013) Millimeters Variations- D Inches Variations- D D See variations SO-24 15.20 15.60 D See variations SO-24 0.599 0.614 H 10 10.65 H 0.394 0.419 L 0.40 1.27 L 0.016 0.050 N See variations N See variations φ 10 ° 8°φ 10 ° 8° N 12 3 EH D L GAUGE PLANE e B A1 A Packaging Information

Copyright  ANPEC Electronics Corp. Rev. A.5 - Mar., 2003 APA7063 www.anpec.com.tw17 Packaging Information (Cont.) PDIP-16 pin ( Reference JEDEC Registration MS-001) D E1 E A e B L Millimeters InchesDim Min. Max. Min. Max. A - 5.320 - 0.210 A1 0.380 - 0.015 - A2 3.169 3.422 0.125 0.135 A3 2.915 3.803 0.115 0.150 D 18.632 19.646 0.735 0.775 E 7.605BSC 0.300BSC E1 6.210 6.464 0.245 0.255 L° 0 380.25 0 15 eB 8.492 9.506 0.335 0.375

Copyright  ANPEC Electronics Corp. Rev. A.5 - Mar., 2003 APA7063 www.anpec.com.tw18 Physical Specifications Reflow Condition (IR/Convection or VPR Reflow) Pre-heat temperature 183 C Peak temperature Time temperature Classification Reflow Profiles Convection or IR/ Convection VPR Average ramp-up rate(183°C to Peak) 3 °C/second max. 10 °C /second max. Preheat temperature 125 ± 25°C) 120 seconds max Temperature maintained above 183°C 60 – 150 seconds Time within 5°C of actual peak temperature 10 –20 seconds 60 seconds Peak temperature range 220 +5/-0°C or 235 +5/-0°C 215-219 °C or 235 +5/-0°C Ramp-down rate 6 °C /second max. 10 °C /second max. Time 25°C to peak temperature 6 minutes max. Package Reflow Conditions pkg. thickness ≥≥≥≥ 2.5mm and all bgas pkg. thickness < 2.5mm and pkg. volume ≥≥≥≥ 350 mm³ pkg. thickness < 2.5mm and pkg. volume < 350mm³ Convection 220 +5/-0 °C Convection 235 +5/-0 °C VPR 215-219 °C VPR 235 +5/-0 °C IR/Convection 220 +5/-0 °C IR/Convection 235 +5/-0 °C Terminal Material Solder-Plated Copper (Solder Material : 90/10 or 63/37 SnPb) Lead Solderability Meets EIA Specification RSI86-91, ANSI/J-STD-002 Category 3. Reference JEDEC Standard J-STD-020A APRIL 1999

Copyright  ANPEC Electronics Corp. Rev. A.5 - Mar., 2003 APA7063 www.anpec.com.tw19 Test item Method Description SOLDERABILITY MIL-STD-883D-2003 245° C , 5 SEC HOLT MIL-STD-883D-1005.7 1000 Hrs Bias @ 125 °C PCT JESD-22-B, A102 168 Hrs, 100 % RH , 121°C TST MIL-STD-883D-1011.9 -65°C ~ 150°C , 200 Cycles ESD MIL-STD-883D-3015.7 VHBM > 2KV, VMM > 200V Latch-Up JESD 78 10ms , I tr > 100mA Reliability test Program Carrier Tape & Reel Dimensions A J B C t Ao E W Po P Ko Bo D F Application A B C J T1 T2 W P E 330 ± 16 2 + 1 . 5 12.75+ F D D1 Po P1 Ao Bo Ko tSOP- 8

Copyright  ANPEC Electronics Corp. Rev. A.5 - Mar., 2003 APA7063 www.anpec.com.tw20 /G32/G30 Customer Service Anpec Electronics Corp. Head Office : 5F, No. 2 Li-Hsin Road, SBIP, Hsin-Chu, Taiwan, R.O.C. Tel : 886-3-5642000 Fax : 886-3-5642050 Taipei Branch : 7F, No. 137, Lane 235, Pac Chiao Rd., Hsin Tien City, Taipei Hsien, Taiwan, R. O. C. Tel : 886-2-89191368 Fax : 886-2-89191369 Cover Tape Dimensions Application Carrier Width Cover Tape Width Devices Per Reel SOP- 8 12 9.3 2500