Power Management

AN80L35RMS

Panasonic Semiconductor

Low-drop type positive output voltage regulator IC

Manufacturer: Panasonic Semiconductor

Document: 26 Pages / 176Kb

Request Quote Download Datasheet Read online HTML view

More from Panasonic Semiconductor Browse A parts

Online Datasheet

Read AN80L35RMS online.

AN80LXXRMS PANASONIC | Alldatasheet

Document overview

Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
PDF pages: 26

Technical content

Low-drop type positive output voltage regulator IC n Overview The AN80LXXRMS series is 0.15 A output low-drop output type positive voltage regulator IC with resetting function. 20 classifications of output voltages, 1.8 V, 1.9 5.2 V are available. In addition, it is adopting the surface mounting type package (Mini 5-pin plastic package), so that it is most suited for miniaturization and weight re- duction of set equipment. n Features

Minimum input and output voltage difference : 0.4 V max.
High precision output voltage : (allowance : – 3%)
Built-in reset function terminal (High : Active)
Built-in overcurrent limiting circuit
Built-in circuit for limiting rush current at input voltage rising time
Output voltage : 1.8 V to 5.2 V n Applications
Cellular phone, PHS, analog cordless phone, other small sized potable equipment n Block diagram Unit : mm Mini-type 5-pin 2.8 +0.2 –0.3 3 2 1.45±0.1 0.95 0.95 1.9±0.10.8 +0.25 –0.05 0.3 +0.1 –0.050.16 0 to 0.1 +0.1 –0.06 2.9 +0.2 –0.05 1.1 +0.2 –0.1 0.4±0.2 0.1 to 0.3 IN 4GND

2 OUT

3 N.C. CONT Current source Start / Stop Error amp. Bandgap reference Type name indication symbol : XX

AN80LXXRMS Series Voltage Regulators n Output Voltage Characteristics at IOUT = 50 mA, Ta = 25°C Type No. Output V Conditions min. typ. max. Unit Marking BA (Marking example : AN80L18RMS)

Voltage Regulators AN80LXXRMS Series n Absolute Maximum Ratings Parameter Symbol Rating Unit Supply voltage *1 V CC 14.6 V Supply current I CC 300 mA Power dissipation *3 PD 78 mW Operating ambient temperature *2 Topr -30 to +85 °C Storage temperature *2 T stg -55 to +150 °C Note) *1 : There may be a case of the device destruction when the output (VOUT ) and the grounding (GND), or the output (VOUT ) and input (VIN) are short-circuited. *2 : All items are at Ta = 25°C, except for the parameter of operating ambient temperature and storage temperature. *3 : Topr = Power dissipation for IC alone without heat sink at + 85°C. Pin No. Description

1 Input voltage pin

2 Output voltage pin

3 N.C. pin

4 Grounding pin

5 Control pin

("High"ﬁ operation "Low"ﬁ stop) Common to the AN80LXXRMS Series n Pin Descriptions

AN80LXXRMS Series Voltage Regulators Parameter Symbol Range Unit Supply voltage V CC 2.2 to 14.5 V Parameter Symbol Conditions Min Typ Max Unit Output voltage V OUT V IN = 2.8 V, IOUT = 50 mA 1.746 1.8 1.854 V Input stability 1 REG IN1 V IN = 2.8 V ﬁ 14.5 V, IOUT = 50 mA ¾ 10 50 mV Input stability 2 REG IN2 V IN = 2.8 V ﬁ 9 V, IOUT = 50 mA ¾ 52 0 m V Load stability *1 REG LOA V IN = 2.8 V, IOUT = 0 mA ﬁ 150 mA ¾ 50 150 mV Peak output current *2 IPEAK V IN = 2.8 V, The output current value 180 240 ¾ mA decreases by 5% from the value when V OUT is at IOUT = 50 mA. Bias current without load I BIAS V IN = 2.8 V, IOUT = 0 mA ¾¾ 350 mA Bias current fluctuation with loadDIBIAS V IN = 2.8 V, IOUT = 0 mA ﬁ 150 mA ¾¾ 5m A Standby consumption current I STB V IN = 10 V, VCONT = 0 V ¾¾ 0.1 mA Bias current before starting IRUSH V IN = 1.5 V, IOUT = 0 mA ¾1 . 5 5m A regulation Ripple rejection ratio R.R. 1 V rms, f = 120 Hz, IOUT = 10 mA 62 70 ¾ dB Minimum input and V DIF(min)1 V IN = 1.5 V, IOUT = 0 mA ¾ 0.1 0.2 V output voltage difference 1 Minimum input and V DIF(min)2 V IN = 2.1 V, IOUT = 150 mA ¾¾ 0.4 V output voltage difference 2 Control terminal threshold high voltageV CONTH V IN = 2.8 V, IOUT = 50 mA ¾¾ 1.50 V Control terminal threshold low voltageV CONTL V IN = 2.8 V, IOUT = 50 mA 0.30 ¾¾ V Control terminal current I CONT V IN = 2.8 V, IOUT = 50 mA ¾¾ 30 mA V CONT = 1.8 V

Design reference data Note) The following values are typical and not guaranteed values. Parameter Symbol Conditions Min Typ Max Unit Output noise voltage V NO 10Hz £ f £ 100kHz, IOUT = 10 mA ¾ 38 ¾m V Output voltage temperature 1 ɾ dV OUT V IN = 2.8 V, IOUT = 0 mA ¾ 90 ¾ ppm/°C coefficient V OUT dT - 30°C £ Ta £ + 85°C Output rise time t ON V IN = 2.8 V, IOUT = 50 mA ¾ 0.10 ¾ ms V CONT = 0 V ﬁ 1.8 V, CIN = 0.1 mF C OUT = 10 mF, VOUT = 90% Note) *1 : 1.0 W *2 : Peak output current : The output current when the output voltage has been decreased by 5% from the value at the time of the output current is 50 mA due to the overcurrent protection. n Electrical Characteristics at Ta = 25°C Note) Unless otherwise specially provided, shorten each test time (within 10 ms) so that the test is conducted under the condition that the drift due to the temperature increase in the chip junction part can be neglected. CIN = 0.1 mF, COUT = 10 mF n Recommended Operating Range AN80L18RMS (1.8 V) Note) *1 : Refer to n Technical Information " • Output rise time characteristics".

Voltage Regulators AN80LXXRMS Series Parameter Symbol Range Unit Supply voltage V CC 2.3 to 14.5 V Parameter Symbol Conditions Min Typ Max Unit Output voltage V OUT V IN = 2.9 V, IOUT = 50 mA 1.843 1.9 1.957 V Input stability 1 REG IN1 V IN = 2.9 V ﬁ 14.5 V, IOUT = 50 mA ¾ 10 50 mV Input stability 2 REG IN2 V IN = 2.9 V ﬁ 9 V, IOUT = 50 mA ¾ 52 0 m V Load stability *1 REG LOA V IN = 2.9 V, IOUT = 0 mA ﬁ 150 mA ¾ 50 150 mV Peak output current *2 IPEAK V IN = 2.9 V, The output current value 180 240 ¾ mA decreases by 5% from the value when V OUT is at IOUT = 50 mA. Bias current without load I BIAS V IN = 2.9 V, IOUT = 0 mA ¾¾ 350 mA Bias current fluctuation with loadDIBIAS V IN = 2.9 V, IOUT = 0 mA ﬁ 150 mA ¾¾ 5m A Standby consumption current I STB V IN = 10 V, VCONT = 0 V ¾¾ 0.1 mA Bias current before starting IRUSH V IN = 1.6 V, IOUT = 0 mA ¾ 1.5 5m A regulation Ripple rejection ratio R.R. 1 V rms, f = 120 Hz, IOUT = 10 mA 62 70 ¾ dB Minimum input and V DIF(min)1 V IN = 1.6 V, IOUT = 0 mA ¾ 0.1 0.2 V output voltage difference 1 Minimum input and V DIF(min)2 V IN = 2.2 V, IOUT = 150 mA ¾¾ 0.4 V output voltage difference 2 Control terminal threshold high voltageV CONTH V IN = 2.9 V, IOUT = 50 mA ¾¾ 1.50 V Control terminal threshold high voltageV CONTH V IN = 2.9 V, IOUT = 50 mA 0.30 ¾¾ V Control terminal current I CONT V IN = 2.9 V, IOUT = 50 mA ¾¾ 30 mA V CONT = 1.8 V

Design reference data Note) The following values are typical and not guaranteed values. Parameter Symbol Conditions Min Typ Max Unit Output noise voltage V NO 10Hz £ f £ 100kHz, IOUT = 10 mA ¾ 40 ¾m V Output voltage temperature 1 ɾ dVOUT V IN = 2.9 V, IOUT = 0 mA ¾ 90 ¾ ppm/°C coefficient V OUT dT - 30°C £ Ta £ + 85°C Output rise time t ON V IN = 2.9 V, IOUT = 50 mA ¾ 0.10 ¾ ms V CONT = 0 V ﬁ 1.8 V, CIN = 0.1 mF C OUT = 10 mF, VOUT = 90% Note) *1 : 1.0 W *2 : Peak output current : The output current when the output voltage has been decreased by 5% from the value at the time of the output current is 50 mA due to the overcurrent protection. n Electrical Characteristics at Ta = 25°C Note) Unless otherwise specially provided, shorten each test time (within 10 ms) so that the test is conducted under the condition that the drift due to the temperature increase in the chip junction part can be neglected. CIN = 0.1 mF, COUT = 10 mF n Recommended Operating Range AN80L19RMS (1.9 V) Note) *1 : Refer to n Technical Information " • Output rise time characteristics".

AN80LXXRMS Series Voltage Regulators Parameter Symbol Range Unit Supply voltage V CC 2.4 to 14.5 V Parameter Symbol Conditions Min Typ Max Unit Output voltage V OUT V IN = 3.0 V, IOUT = 50 mA 1.940 2.0 2.060 V Input stability 1 REG IN1 V IN = 3.0 V ﬁ 14.5 V, IOUT = 50 mA ¾ 10 50 mV Input stability 2 REG IN2 V IN = 3.0 V ﬁ 9 V, IOUT = 50 mA ¾ 52 0 m V Load stability *1 REG LOA V IN = 3.0 V, IOUT = 0 mA ﬁ 150 mA ¾ 50 150 mV Peak output current *2 IPEAK V IN = 3.0 V, The output current value 180 240 ¾ mA decreases by 5% from the value when V OUT is at IOUT = 50 mA. Bias current without load I BIAS V IN = 3.0 V, IOUT = 0 mA ¾¾ 350 mA Bias current fluctuation with loadDIBIAS V IN = 3.0 V, IOUT = 0 mA ﬁ 150 mA ¾¾ 5m A Standby consumption current I STB V IN = 10 V, VCONT = 0 V ¾¾ 0.1 mA Bias current before starting IRUSH V IN = 1.7 V, IOUT = 0 mA ¾1 . 5 5m A regulation Ripple rejection ratio R.R. 1 V rms, f = 120 Hz, IOUT = 10 mA 62 70 ¾ dB Minimum input and V DIF(min)1 V IN = 1.7 V, IOUT = 0 mA ¾ 0.1 0.2 V output voltage difference 1 Minimum input and V DIF(min)2 V IN = 2.3 V, IOUT = 150 mA ¾¾ 0.4 V output voltage difference 2 Control terminal threshold high voltageV CONTH V IN = 3.0 V, IOUT = 50 mA ¾¾ 1.50 V Control terminal threshold high voltageV CONTH V IN = 3.0 V, IOUT = 50 mA 0.30 ¾¾ V Control terminal current I CONT V IN = 3.0 V, IOUT = 50 mA ¾¾ 30 mA V CONT = 1.8 V

Design reference data Note) The following values are typical and not guaranteed values. Parameter Symbol Conditions Min Typ Max Unit Output noise voltage V NO 10Hz £ f £ 100kHz, IOUT = 10 mA ¾ 42 ¾m V Output voltage temperature 1 ɾ dV OUT V IN = 3.0 V, IOUT = 0 mA ¾ 90 ¾ ppm/°C coefficient V OUT dT - 30°C £ Ta £ + 85°C Output rise time t ON V IN = 3.0 V, IOUT = 50 mA ¾ 0.10 ¾ ms V CONT = 0 V ﬁ 1.8 V, CIN = 0.1 mF C OUT = 10 mF, VOUT = 90% Note) *1 : 1.0 W *2 : Peak output current : The output current when the output voltage has been decreased by 5% from the value at the time of the output current is 50 mA due to the overcurrent protection. n Electrical Characteristics at Ta = 25°C Note) Unless otherwise specially provided, shorten each test time (within 10 ms) so that the test is conducted under the condition that the drift due to the temperature increase in the chip junction part can be neglected. CIN = 0.1 mF, COUT = 10 mF n Recommended Operating Range AN80L20RMS (2.0 V) Note) *1 : Refer to n Technical Information " • Output rise time characteristics".

Voltage Regulators AN80LXXRMS Series Parameter Symbol Range Unit Supply voltage V CC 2.5 to 14.5 V Parameter Symbol Conditions Min Typ Max Unit Output voltage V OUT V IN = 3.1 V, IOUT = 50 mA 2.037 2.1 2.163 V Input stability 1 REG IN1 V IN = 3.1 V ﬁ 14.5 V, IOUT = 50 mA ¾ 10 50 mV Input stability 2 REG IN2 V IN = 3.1 V ﬁ 9 V, IOUT = 50 mA ¾ 52 0 m V Load stability *1 REG LOA V IN = 3.1 V, IOUT = 0 mA ﬁ 150 mA ¾ 50 150 mV Peak output current *2 IPEAK V IN = 3.1 V, The output current value 180 240 ¾ mA decreases by 5% from the value when V OUT is at IOUT = 50 mA. Bias current without load I BIAS V IN = 3.1 V, IOUT = 0 mA ¾¾ 350 mA Bias current fluctuation with loadDIBIAS V IN = 3.1 V, IOUT = 0 mA ﬁ 150 mA ¾¾ 5m A Standby consumption current I STB V IN = 10 V, VCONT = 0 V ¾¾ 0.1 mA Bias current before starting IRUSH V IN = 1.8 V, IOUT = 0 mA ¾ 1.5 5m A regulation Ripple rejection ratio R.R. 1 V rms, f = 120 Hz, IOUT = 10 mA 61 69 ¾ dB Minimum input and V DIF(min)1 V IN = 1.8 V, IOUT = 0 mA ¾ 0.1 0.2 V output voltage difference 1 Minimum input and V DIF(min)2 V IN = 2.4 V, IOUT = 150 mA ¾¾ 0.4 V output voltage difference 2 Control terminal threshold high voltageV CONTH V IN = 3.1 V, IOUT = 50 mA ¾¾ 1.50 V Control terminal threshold high voltageV CONTH V IN = 3.1 V, IOUT = 50 mA 0.30 ¾¾ V Control terminal current I CONT V IN = 3.1 V, IOUT = 50 mA ¾¾ 30 mA V CONT = 1.8 V

Design reference data Note) The following values are typical and not guaranteed values. Parameter Symbol Conditions Min Typ Max Unit Output noise voltage V NO 10Hz £ f £ 100kHz, IOUT = 10 mA ¾ 44 ¾m V Output voltage temperature 1 ɾ dVOUT V IN = 3.1 V, IOUT = 0 mA ¾ 90 ¾ ppm/°C coefficient V OUT dT - 30°C £ Ta £ + 85°C Output rise time t ON V IN = 3.1 V, IOUT = 50 mA ¾ 0.10 ¾ ms V CONT = 0 V ﬁ 1.8 V, CIN = 0.1 mF C OUT = 10 mF, VOUT = 90% Note) *1 : 1.0 W *2 : Peak output current : The output current when the output voltage has been decreased by 5% from the value at the time of the output current is 50 mA due to the overcurrent protection. n Electrical Characteristics at Ta = 25°C Note) Unless otherwise specially provided, shorten each test time (within 10 ms) so that the test is conducted under the condition that the drift due to the temperature increase in the chip junction part can be neglected. CIN = 0.1 mF, COUT = 10 mF n Recommended Operating Range AN80L21RMS (2.1 V) Note) *1 : Refer to n Technical Information " • Output rise time characteristics".

AN80LXXRMS Series Voltage Regulators Parameter Symbol Range Unit Supply voltage V CC 2.6 to 14.5 V Parameter Symbol Conditions Min Typ Max Unit Output voltage V OUT V IN = 3.2 V, IOUT = 50 mA 2.134 2.2 2.266 V Input stability 1 REG IN1 V IN = 3.2 V ﬁ 14.5 V, IOUT = 50 mA ¾ 10 50 mV Input stability 2 REG IN2 V IN = 3.2 V ﬁ 9 V, IOUT = 50 mA ¾ 52 0 m V Load stability *1 REG LOA V IN = 3.2 V, IOUT = 0 mA ﬁ 150 mA ¾ 50 150 mV Peak output current *2 IPEAK V IN = 3.2 V, The output current value 180 240 ¾ mA decreases by 5% from the value when V OUT is at IOUT = 50 mA. Bias current without load I BIAS V IN = 3.2 V, IOUT = 0 mA ¾¾ 350 mA Bias current fluctuation with loadDIBIAS V IN = 3.2 V, IOUT = 0 mA ﬁ 150 mA ¾¾ 5m A Standby consumption current I STB V IN = 10 V, VCONT = 0 V ¾¾ 0.1 mA Bias current before starting IRUSH V IN = 1.9 V, IOUT = 0 mA ¾1 . 5 5m A regulation Ripple rejection ratio R.R. 1 V rms, f = 120 Hz, IOUT = 10 mA 61 69 ¾ dB Minimum input and V DIF(min)1 V IN = 1.9 V, IOUT = 0 mA ¾ 0.1 0.2 V output voltage difference 1 Minimum input and V DIF(min)2 V IN = 2.4 V, IOUT = 150 mA ¾¾ 0.4 V output voltage difference 2 Control terminal threshold high voltageV CONTH V IN = 3.2 V, IOUT = 50 mA ¾¾ 1.50 V Control terminal threshold high voltageV CONTH V IN = 3.2 V, IOUT = 50 mA 0.30 ¾¾ V Control terminal current I CONT V IN = 3.2 V, IOUT = 50 mA ¾¾ 30 mA V CONT = 1.8 V

Design reference data Note) The following values are typical and not guaranteed values. Parameter Symbol Conditions Min Typ Max Unit Output noise voltage V NO 10Hz £ f £ 100kHz, IOUT =10 mA ¾ 46 ¾m V Output voltage temperature 1 ɾ dV OUT V IN = 3.2 V, IOUT = 0 mA ¾ 90 ¾ ppm/°C coefficient V OUT dT - 30°C £ Ta £ + 85°C Output rise time t ON V IN = 3.2 V, IOUT = 50 mA ¾ 0.10 ¾ ms V CONT = 0 V ﬁ 1.8 V, CIN = 0.1 mF C OUT = 10 mF, VOUT = 90% Note) *1 : 1.0 W *2 : Peak output current : The output current when the output voltage has been decreased by 5% from the value at the time of the output current is 50 mA due to the overcurrent protection. n Electrical Characteristics at Ta = 25°C Note) Unless otherwise specially provided, shorten each test time (within 10 ms) so that the test is conducted under the condition that the drift due to the temperature increase in the chip junction part can be neglected. CIN = 0.1 mF, COUT = 10 mF n Recommended Operating Range AN80L22RMS (2.2 V) Note) *1 : Refer to n Technical Information " • Output rise time characteristics".

Voltage Regulators AN80LXXRMS Series Parameter Symbol Range Unit Supply voltage V CC 2.9 to 14.5 V Parameter Symbol Conditions Min Typ Max Unit Output voltage V OUT V IN = 3.5 V, IOUT = 50 mA 2.425 2.5 2.575 V Input stability 1 REG IN1 V IN = 3.5 V ﬁ 14.5 V, IOUT = 50 mA ¾ 10 50 mV Input stability 2 REG IN2 V IN = 3.5 V ﬁ 9 V, IOUT = 50 mA ¾ 52 0 m V Load stability *1 REG LOA V IN = 3.5 V, IOUT = 0 mA ﬁ 150 mA ¾ 50 150 mV Peak output current *2 IPEAK V IN = 3.5 V, The output current value 180 240 ¾ mA decreases by 5% from the value when V OUT is at IOUT = 50 mA. Bias current without load I BIAS V IN = 3.5 V, IOUT = 0 mA ¾¾ 350 mA Bias current fluctuation with loadDIBIAS V IN = 3.5 V, IOUT = 0 mA ﬁ 150 mA ¾¾ 5m A Standby consumption current I STB V IN = 10 V, VCONT = 0 V ¾¾ 0.1 mA Bias current before starting IRUSH V IN = 2.2 V, IOUT = 0 mA ¾ 1.5 5m A regulation Ripple rejection ratio R.R. 1 V rms, f = 120 Hz, IOUT = 10 mA 60 68 ¾ dB Minimum input and V DIF(min)1 V IN = 2.2 V, IOUT = 0 mA ¾ 0.1 0.2 V output voltage difference 1 Minimum input and V DIF(min)2 V IN = 2.6 V, IOUT = 150 mA ¾¾ 0.4 V output voltage difference 2 Control terminal threshold high voltageV CONTH V IN = 3.5 V, IOUT = 50 mA ¾¾ 1.50 V Control terminal threshold high voltageV CONTH V IN = 3.5 V, IOUT = 50 mA 0.30 ¾¾ V Control terminal current I CONT V IN = 3.5 V, IOUT = 50 mA ¾¾ 30 mA V CONT = 1.8 V

Design reference data Note) The following values are typical and not guaranteed values. Parameter Symbol Conditions Min Typ Max Unit Output noise voltage V NO 10Hz £ f £ 100kHz, IOUT = 10 mA ¾ 58 ¾m V Output voltage temperature 1 ɾ dVOUT V IN = 3.5 V, IOUT = 0 mA ¾ 90 ¾ ppm/°C coefficient V OUT dT - 30°C £ Ta £ + 85°C Output rise time t ON V IN = 3.15 V, IOUT = 50 mA ¾ 0.10 ¾ ms V CONT = 0 V ﬁ 1.8 V, CIN = 0.1 mF C OUT = 10 mF, VOUT = 90% Note) *1 : 1.0 W *2 : Peak output current : The output current when the output voltage has been decreased by 5% from the value at the time of the output current is 50 mA due to the overcurrent protection. n Electrical Characteristics at Ta = 25°C Note) Unless otherwise specially provided, shorten each test time (within 10 ms) so that the test is conducted under the condition that the drift due to the temperature increase in the chip junction part can be neglected. CIN = 0.1 mF, COUT = 10 mF n Recommended Operating Range AN80L25RMS (2.5 V) Note) *1 : Refer to n Technical Information " • Output rise time characteristics".

AN80LXXRMS Series Voltage Regulators Parameter Symbol Range Unit Supply voltage V CC 3.2 to 14.5 V Parameter Symbol Conditions Min Typ Max Unit Output voltage V OUT V IN = 3.8 V, IOUT = 50 mA 2.716 2.8 2.884 V Input stability 1 REG IN1 V IN = 3.8 V ﬁ 14.5 V, IOUT = 50 mA ¾ 10 50 mV Input stability 2 REG IN2 V IN = 3.8 V ﬁ 9 V, IOUT = 50 mA ¾ 52 0 m V Load stability *1 REG LOA V IN = 3.8 V, IOUT = 0 mA ﬁ 150 mA ¾ 50 150 mV Peak output current *2 IPEAK V IN = 3.8 V, The output current value 180 240 ¾ mA decreases by 5% from the value when V OUT is at IOUT = 50 mA. Bias current without load I BIAS V IN = 3.8 V, IOUT = 0 mA ¾¾ 350 mA Bias current fluctuation with loadDIBIAS V IN = 3.8 V, IOUT = 0 mA ﬁ 150 mA ¾¾ 5m A Standby consumption current I STB V IN = 10 V, VCONT = 0 V ¾¾ 0.1 mA Bias current before starting IRUSH V IN = 2.5 V, IOUT = 0 mA ¾1 . 5 5m A regulation Ripple rejection ratio R.R. 1 V rms, f = 120 Hz, IOUT = 10 mA 60 68 ¾ dB Minimum input and V DIF(min)1 V IN = 2.5 V, IOUT = 0 mA ¾ 0.1 0.2 V output voltage difference 1 Minimum input and V DIF(min)2 V IN = 2.9 V, IOUT = 150 mA ¾¾ 0.4 V output voltage difference 2 Control terminal threshold high voltageV CONTH V IN = 3.8 V, IOUT = 50 mA ¾¾ 1.50 V Control terminal threshold high voltageV CONTH V IN = 3.8 V, IOUT = 50 mA 0.30 ¾¾ V Control terminal current I CONT V IN = 3.8 V, IOUT = 50 mA ¾¾ 30 mA V CONT = 1.8 V

Design reference data Note) The following values are typical and not guaranteed values. Parameter Symbol Conditions Min Typ Max Unit Output noise voltage V NO 10Hz £ f £ 100kHz, IOUT =10 mA ¾ 58 ¾m V Output voltage temperature 1 ɾ dV OUT V IN = 3.8 V, IOUT = 0 mA ¾ 90 ¾ ppm/°C coefficient V OUT dT - 30°C £ Ta £ + 85°C Output rise time t ON V IN = 3.8 V, IOUT = 50 mA ¾ 0.10 ¾ ms V CONT = 0 V ﬁ 1.8 V, CIN = 0.1 mF C OUT = 10 mF, VOUT = 90% Note) *1 : 1.0 W *2 : Peak output current : The output current when the output voltage has been decreased by 5% from the value at the time of the output current is 50 mA due to the overcurrent protection. n Electrical Characteristics at Ta = 25°C Note) Unless otherwise specially provided, shorten each test time (within 10 ms) so that the test is conducted under the condition that the drift due to the temperature increase in the chip junction part can be neglected. CIN = 0.1 mF, COUT = 10 mF n Recommended Operating Range AN80L28RMS (2.8 V) Note) *1 : Refer to n Technical Information " • Output rise time characteristics".

Voltage Regulators AN80LXXRMS Series Parameter Symbol Range Unit Supply voltage V CC 3.3 to 14.5 V Parameter Symbol Conditions Min Typ Max Unit Output voltage V OUT V IN = 3.9 V, IOUT = 50 mA 2.813 2.9 2.987 V Input stability 1 REG IN1 V IN = 3.9 V ﬁ 14.5 V, IOUT = 50 mA ¾ 10 50 mV Input stability 2 REG IN2 V IN = 3.9 V ﬁ 9 V, IOUT = 50 mA ¾ 52 0 m V Load stability *1 REG LOA V IN = 3.9 V, IOUT = 0 mA ﬁ 150 mA ¾ 50 150 mV Peak output current *2 IPEAK V IN = 3.9 V, The output current value 180 240 ¾ mA decreases by 5% from the value when V OUT is at IOUT = 50 mA. Bias current without load I BIAS V IN = 3.9 V, IOUT = 0 mA ¾¾ 350 mA Bias current fluctuation with loadDIBIAS V IN = 3.9 V, IOUT = 0 mA ﬁ 150 mA ¾¾ 5m A Standby consumption current I STB V IN = 10 V, VCONT = 0 V ¾¾ 0.1 mA Bias current before starting IRUSH V IN = 2.6 V, IOUT = 0 mA ¾ 1.5 5m A regulation Ripple rejection ratio R.R. 1 V rms, f = 120 Hz, IOUT = 10 mA 60 68 ¾ dB Minimum input and V DIF(min)1 V IN = 2.6 V, IOUT = 0 mA ¾ 0.1 0.2 V output voltage difference 1 Minimum input and V DIF(min)2 V IN = 3.0 V, IOUT = 150 mA ¾¾ 0.4 V output voltage difference 2 Control terminal threshold high voltageV CONTH V IN = 3.9 V, IOUT = 50 mA ¾¾ 1.50 V Control terminal threshold high voltageV CONTH V IN = 3.9 V, IOUT = 50 mA 0.30 ¾¾ V Control terminal current I CONT V IN = 3.9 V, IOUT = 50 mA ¾¾ 30 mA V CONT = 1.8 V

Design reference data Note) The following values are typical and not guaranteed values. Parameter Symbol Conditions Min Typ Max Unit Output noise voltage V NO 10Hz £ f £ 100kHz, IOUT = 10 mA ¾ 60 ¾m V Output voltage temperature 1 ɾ dVOUT V IN = 3.9 V, IOUT = 0 mA ¾ 90 ¾ ppm/°C coefficient V OUT dT - 30°C £ Ta £ + 85°C Output rise time t ON V IN = 3.9 V, IOUT = 50 mA ¾ 0.12 ¾ ms V CONT = 0 V ﬁ 1.8 V, CIN = 0.1 mF C OUT = 10 mF, VOUT = 90% Note) *1 : 1.0 W *2 : Peak output current : The output current when the output voltage has been decreased by 5% from the value at the time of the output current is 50 mA due to the overcurrent protection. n Electrical Characteristics at Ta = 25°C Note) Unless otherwise specially provided, shorten each test time (within 10 ms) so that the test is conducted under the condition that the drift due to the temperature increase in the chip junction part can be neglected. CIN = 0.1 mF, COUT = 10 mF n Recommended Operating Range AN80L29RMS (2.9 V) Note) *1 : Refer to n Technical Information " • Output rise time characteristics".

AN80LXXRMS Series Voltage Regulators Parameter Symbol Range Unit Supply voltage V CC 3.4 to 14.5 V Parameter Symbol Conditions Min Typ Max Unit Output voltage V OUT V IN = 4.0 V, IOUT = 50 mA 2.910 3.0 3.090 V Input stability 1 REG IN1 V IN = 4.0 V ﬁ 14.5 V, IOUT = 50 mA ¾ 10 50 mV Input stability 2 REG IN2 V IN = 4.0 V ﬁ 9 V, IOUT = 50 mA ¾ 52 0 m V Load stability *1 REG LOA V IN = 4.0 V, IOUT = 0 mA ﬁ 150 mA ¾ 50 150 mV Peak output current *2 IPEAK V IN = 4.0 V, The output current value 180 240 ¾ mA decreases by 5% from the value when V OUT is at IOUT = 50 mA. Bias current without load I BIAS V IN = 4.0 V, IOUT = 0 mA ¾¾ 350 mA Bias current fluctuation with loadDIBIAS V IN = 4.0 V, IOUT = 0 mA ﬁ 150 mA ¾¾ 5m A Standby consumption current I STB V IN = 10 V, VCONT = 0 V ¾¾ 0.1 mA Bias current before starting IRUSH V IN = 2.7 V, IOUT = 0 mA ¾1 . 5 5m A regulation Ripple rejection ratio R.R. 1 V rms, f = 120 Hz, IOUT = 10 mA 60 68 ¾ dB Minimum input and V DIF(min)1 V IN = 2.7 V, IOUT = 0 mA ¾ 0.1 0.2 V output voltage difference 1 Minimum input and V DIF(min)2 V IN = 3.1 V, IOUT = 150 mA ¾¾ 0.4 V output voltage difference 2 Control terminal threshold high voltageV CONTH V IN = 4.0 V, IOUT = 50 mA ¾¾ 1.50 V Control terminal threshold high voltageV CONTH V IN = 4.0 V, IOUT = 50 mA 0.30 ¾¾ V Control terminal current I CONT V IN = 4.0 V, IOUT = 50 mA ¾¾ 30 mA V CONT = 1.8 V

Design reference data Note) The following values are typical and not guaranteed values. Parameter Symbol Conditions Min Typ Max Unit Output noise voltage V NO 10Hz £ f £ 100kHz, IOUT =10 mA ¾ 62 ¾m V Output voltage temperature 1 ɾ dV OUT V IN = 4.0 V, IOUT = 0 mA ¾ 90 ¾ ppm/°C coefficient V OUT dT - 30°C £ Ta £ + 85°C Output rise time t ON V IN = 4.0 V, IOUT = 50 mA ¾ 0.12 ¾ ms V CONT = 0 V ﬁ 1.8 V, CIN = 0.1 mF C OUT = 10 mF, VOUT = 90% Note) *1 : 1.0 W *2 : Peak output current : The output current when the output voltage has been decreased by 5% from the value at the time of the output current is 50 mA due to the overcurrent protection. n Electrical Characteristics at Ta = 25°C Note) Unless otherwise specially provided, shorten each test time (within 10 ms) so that the test is conducted under the condition that the drift due to the temperature increase in the chip junction part can be neglected. CIN = 0.1 mF, COUT = 10 mF n Recommended Operating Range AN80L30RMS (3.0 V) Note) *1 : Refer to n Technical Information " • Output rise time characteristics".

Voltage Regulators AN80LXXRMS Series Parameter Symbol Range Unit Supply voltage V CC 3.5 to 14.5 V Parameter Symbol Conditions Min Typ Max Unit Output voltage V OUT V IN = 4.1 V, IOUT = 50 mA 3.007 3.1 3.193 V Input stability 1 REG IN1 V IN = 4.1 V ﬁ 14.5 V, IOUT = 50 mA ¾ 10 50 mV Input stability 2 REG IN2 V IN = 4.1 V ﬁ 9 V, IOUT = 50 mA ¾ 52 0 m V Load stability *1 REG LOA V IN = 4.1 V, IOUT = 0 mA ﬁ 150 mA ¾ 50 150 mV Peak output current *2 IPEAK V IN = 4.1 V, The output current value 180 240 ¾ mA decreases by 5% from the value when V OUT is at IOUT = 50 mA. Bias current without load I BIAS V IN = 4.1 V, IOUT = 0 mA ¾¾ 350 mA Bias current fluctuation with loadDIBIAS V IN = 4.1 V, IOUT = 0 mA ﬁ 150 mA ¾¾ 5m A Standby consumption current I STB V IN = 10 V, VCONT = 0 V ¾¾ 0.1 mA Bias current before starting IRUSH V IN = 2.8 V, IOUT = 0 mA ¾ 1.5 5m A regulation Ripple rejection ratio R.R. 1 V rms, f = 120 Hz, IOUT = 10 mA 59 67 ¾ dB Minimum input and V DIF(min)1 V IN = 2.8 V, IOUT = 0 mA ¾ 0.1 0.2 V output voltage difference 1 Minimum input and V DIF(min)2 V IN = 3.2 V, IOUT = 150 mA ¾¾ 0.4 V output voltage difference 2 Control terminal threshold high voltageV CONTH V IN = 4.1 V, IOUT = 50 mA ¾¾ 1.50 V Control terminal threshold high voltageV CONTH V IN = 4.1 V, IOUT = 50 mA 0.30 ¾¾ V Control terminal current I CONT V IN = 4.1 V, IOUT = 50 mA ¾¾ 30 mA V CONT = 1.8 V

Design reference data Note) The following values are typical and not guaranteed values. Parameter Symbol Conditions Min Typ Max Unit Output noise voltage V NO 10Hz £ f £ 100kHz, IOUT = 10 mA ¾ 64 ¾m V Output voltage temperature 1 ɾ dVOUT V IN = 4.1 V, IOUT = 0 mA ¾ 90 ¾ ppm/°C coefficient V OUT dT - 30°C £ Ta £ + 85°C Output rise time t ON V IN = 4.1 V, IOUT = 50 mA ¾ 0.12 ¾ ms V CONT = 0 V ﬁ 1.8 V, CIN = 0.1 mF C OUT = 10 mF, VOUT = 90% Note) *1 : 1.0 W *2 : Peak output current : The output current when the output voltage has been decreased by 5% from the value at the time of the output current is 50 mA due to the overcurrent protection. n Electrical Characteristics at Ta = 25°C Note) Unless otherwise specially provided, shorten each test time (within 10 ms) so that the test is conducted under the condition that the drift due to the temperature increase in the chip junction part can be neglected. CIN = 0.1 mF, COUT = 10 mF n Recommended Operating Range AN80L31RMS (3.1 V) Note) *1 : Refer to n Technical Information " • Output rise time characteristics".

AN80LXXRMS Series Voltage Regulators Parameter Symbol Range Unit Supply voltage V CC 3.6 to 14.5 V Parameter Symbol Conditions Min Typ Max Unit Output voltage V OUT V IN = 4.2 V, IOUT = 50 mA 3.104 3.2 3.296 V Input stability 1 REG IN1 V IN = 4.2 V ﬁ 14.5 V, IOUT = 50 mA ¾ 10 50 mV Input stability 2 REG IN2 V IN = 4.2 V ﬁ 9 V, IOUT = 50 mA ¾ 52 0 m V Load stability *1 REG LOA V IN = 4.2 V, IOUT = 0 mA ﬁ 150 mA ¾ 50 150 mV Peak output current *2 IPEAK V IN = 4.2 V, The output current value 180 240 ¾ mA decreases by 5% from the value when V OUT is at IOUT = 50 mA. Bias current without load I BIAS V IN = 4.2 V, IOUT = 0 mA ¾¾ 350 mA Bias current fluctuation with loadDIBIAS V IN = 4.2 V, IOUT = 0 mA ﬁ 150 mA ¾¾ 5m A Standby consumption current I STB V IN = 10 V, VCONT = 0 V ¾¾ 0.1 mA Bias current before starting IRUSH V IN = 2.9 V, IOUT = 0 mA ¾1 . 5 5m A regulation Ripple rejection ratio R.R. 1 V rms, f = 120 Hz, IOUT = 10 mA 59 67 ¾ dB Minimum input and V DIF(min)1 V IN = 2.9 V, IOUT = 0 mA ¾ 0.1 0.2 V output voltage difference 1 Minimum input and V DIF(min)2 V IN = 3.3 V, IOUT = 150 mA ¾¾ 0.4 V output voltage difference 2 Control terminal threshold high voltageV CONTH V IN = 4.2 V, IOUT = 50 mA ¾¾ 1.50 V Control terminal threshold high voltageV CONTH V IN = 4.2 V, IOUT = 50 mA 0.30 ¾¾ V Control terminal current I CONT V IN = 4.2 V, IOUT = 50 mA ¾¾ 30 mA V CONT = 1.8 V

Design reference data Note) The following values are typical and not guaranteed values. Parameter Symbol Conditions Min Typ Max Unit Output noise voltage V NO 10Hz £ f £ 100kHz, IOUT =10 mA ¾ 66 ¾m V Output voltage temperature 1 ɾ dV OUT V IN = 4.2 V, IOUT = 0 mA ¾ 90 ¾ ppm/°C coefficient V OUT dT - 30°C £ Ta £ + 85°C Output rise time t ON V IN = 4.2 V, IOUT = 50 mA ¾ 0.12 ¾ ms V CONT = 0 V ﬁ 1.8 V, CIN = 0.1 mF C OUT = 10 mF, VOUT = 90% Note) *1 : 1.0 W *2 : Peak output current : The output current when the output voltage has been decreased by 5% from the value at the time of the output current is 50 mA due to the overcurrent protection. n Electrical Characteristics at Ta = 25°C Note) Unless otherwise specially provided, shorten each test time (within 10 ms) so that the test is conducted under the condition that the drift due to the temperature increase in the chip junction part can be neglected. CIN = 0.1 mF, COUT = 10 mF n Recommended Operating Range AN80L32RMS (3.2 V) Note) *1 : Refer to n Technical Information " • Output rise time characteristics".

Voltage Regulators AN80LXXRMS Series Parameter Symbol Range Unit Supply voltage V CC 3.7 to 14.5 V Parameter Symbol Conditions Min Typ Max Unit Output voltage V OUT V IN = 4.3 V, IOUT = 50 mA 3.201 3.3 3.399 V Input stability 1 REG IN1 V IN = 4.3 V ﬁ 14.5 V, IOUT = 50 mA ¾ 10 50 mV Input stability 2 REG IN2 V IN = 4.3 V ﬁ 9 V, IOUT = 50 mA ¾ 52 0 m V Load stability *1 REG LOA V IN = 4.3 V, IOUT = 0 mA ﬁ 150 mA ¾ 50 150 mV Peak output current *2 IPEAK V IN = 4.3 V, The output current value 180 240 ¾ mA decreases by 5% from the value when V OUT is at IOUT = 50 mA. Bias current without load I BIAS V IN = 4.3 V, IOUT = 0 mA ¾¾ 350 mA Bias current fluctuation with loadDIBIAS V IN = 4.3 V, IOUT = 0 mA ﬁ 150 mA ¾¾ 5m A Standby consumption current I STB V IN = 10 V, VCONT = 0 V ¾¾ 0.1 mA Bias current before starting IRUSH V IN = 3.0 V, IOUT = 0 mA ¾ 1.5 5m A regulation Ripple rejection ratio R.R. 1 V rms, f = 120 Hz, IOUT = 10 mA 59 67 ¾ dB Minimum input and V DIF(min)1 V IN = 3.0 V, IOUT = 0 mA ¾ 0.1 0.2 V output voltage difference 1 Minimum input and V DIF(min)2 V IN = 3.4 V, IOUT = 150 mA ¾¾ 0.4 V output voltage difference 2 Control terminal threshold high voltageV CONTH V IN = 4.3 V, IOUT = 50 mA ¾¾ 1.50 V Control terminal threshold high voltageV CONTH V IN = 4.3 V, IOUT = 50 mA 0.30 ¾¾ V Control terminal current I CONT V IN = 4.3 V, IOUT = 50 mA ¾¾ 30 mA V CONT = 1.8 V

Design reference data Note) The following values are typical and not guaranteed values. Parameter Symbol Conditions Min Typ Max Unit Output noise voltage V NO 10Hz £ f £ 100kHz, IOUT = 10 mA ¾ 68 ¾m V Output voltage temperature 1 ɾ dVOUT V IN = 4.3 V, IOUT = 0 mA ¾ 90 ¾ ppm/°C coefficient V OUT dT - 30°C £ Ta £ + 85°C Output rise time t ON V IN = 4.3 V, IOUT = 50 mA ¾ 0.12 ¾ ms V CONT = 0 V ﬁ 1.8 V, CIN = 0.1 mF C OUT = 10 mF, VOUT = 90% Note) *1 : 1.0 W *2 : Peak output current : The output current when the output voltage has been decreased by 5% from the value at the time of the output current is 50 mA due to the overcurrent protection. n Electrical Characteristics at Ta = 25°C Note) Unless otherwise specially provided, shorten each test time (within 10 ms) so that the test is conducted under the condition that the drift due to the temperature increase in the chip junction part can be neglected. CIN = 0.1 mF, COUT = 10 mF n Recommended Operating Range AN80L33RMS (3.3 V) Note) *1 : Refer to n Technical Information " • Output rise time characteristics".

AN80LXXRMS Series Voltage Regulators Parameter Symbol Range Unit Supply voltage V CC 3.8 to 14.5 V Parameter Symbol Conditions Min Typ Max Unit Output voltage V OUT V IN = 4.4 V, IOUT = 50 mA 3.298 3.4 3.502 V Input stability 1 REG IN1 V IN = 4.4 V ﬁ 14.5 V, IOUT = 50 mA ¾ 10 50 mV Input stability 2 REG IN2 V IN = 4.4 V ﬁ 9 V, IOUT = 50 mA ¾ 52 0 m V Load stability *1 REG LOA V IN = 4.4 V, IOUT = 0 mA ﬁ 150 mA ¾ 50 150 mV Peak output current *2 IPEAK V IN = 4.4 V, The output current value 180 240 ¾ mA decreases by 5% from the value when V OUT is at IOUT = 50 mA. Bias current without load I BIAS V IN = 4.4 V, IOUT = 0 mA ¾¾ 350 mA Bias current fluctuation with loadDIBIAS V IN = 4.4 V, IOUT = 0 mA ﬁ 150 mA ¾¾ 5m A Standby consumption current I STB V IN = 10 V, VCONT = 0 V ¾¾ 0.1 mA Bias current before starting IRUSH V IN = 3.1 V, IOUT = 0 mA ¾1 . 5 5m A regulation Ripple rejection ratio R.R. 1 V rms, f = 120 Hz, IOUT = 10 mA 58 66 ¾ dB Minimum input and V DIF(min)1 V IN = 3.1 V, IOUT = 0 mA ¾ 0.1 0.2 V output voltage difference 1 Minimum input and V DIF(min)2 V IN = 3.5 V, IOUT = 150 mA ¾¾ 0.4 V output voltage difference 2 Control terminal threshold high voltageV CONTH V IN = 4.4 V, IOUT = 50 mA ¾¾ 1.50 V Control terminal threshold high voltageV CONTH V IN = 4.4 V, IOUT = 50 mA 0.30 ¾¾ V Control terminal current I CONT V IN = 4.4 V, IOUT = 50 mA ¾¾ 30 mA V CONT = 1.8 V

Design reference data Note) The following values are typical and not guaranteed values. Parameter Symbol Conditions Min Typ Max Unit Output noise voltage V NO 10Hz £ f £ 100kHz, IOUT =10 mA ¾ 70 ¾m V Output voltage temperature 1 ɾ dV OUT V IN = 4.4 V, IOUT = 0 mA ¾ 90 ¾ ppm/°C coefficient V OUT dT - 30°C £ Ta £ + 85°C Output rise time t ON V IN = 4.4 V, IOUT = 50 mA ¾ 0.12 ¾ ms V CONT = 0 V ﬁ 1.8 V, CIN = 0.1 mF C OUT = 10 mF, VOUT = 90% Note) *1 : 1.0 W *2 : Peak output current : The output current when the output voltage has been decreased by 5% from the value at the time of the output current is 50 mA due to the overcurrent protection. n Electrical Characteristics at Ta = 25°C Note) Unless otherwise specially provided, shorten each test time (within 10 ms) so that the test is conducted under the condition that the drift due to the temperature increase in the chip junction part can be neglected. CIN = 0.1 mF, COUT = 10 mF n Recommended Operating Range AN80L34RMS (3.4 V) Note) *1 : Refer to n Technical Information " • Output rise time characteristics".

Voltage Regulators AN80LXXRMS Series Parameter Symbol Range Unit Supply voltage V CC 3.9 to 14.5 V Parameter Symbol Conditions Min Typ Max Unit Output voltage V OUT V IN = 4.5 V, IOUT = 50 mA 3.395 3.5 3.605 V Input stability 1 REG IN1 V IN = 4.5 V ﬁ 14.5 V, IOUT = 50 mA ¾ 10 50 mV Input stability 2 REG IN2 V IN = 4.5 V ﬁ 9 V, IOUT = 50 mA ¾ 52 0 m V Load stability *1 REG LOA V IN = 4.5 V, IOUT = 0 mA ﬁ 150 mA ¾ 50 150 mV Peak output current *2 IPEAK V IN = 4.5 V, The output current value 180 240 ¾ mA decreases by 5% from the value when V OUT is at IOUT = 50 mA. Bias current without load I BIAS V IN = 4.5 V, IOUT = 0 mA ¾¾ 350 mA Bias current fluctuation with loadDIBIAS V IN = 4.5 V, IOUT = 0 mA ﬁ 150 mA ¾¾ 5m A Standby consumption current I STB V IN = 10 V, VCONT = 0 V ¾¾ 0.1 mA Bias current before starting IRUSH V IN = 3.2 V, IOUT = 0 mA ¾ 1.5 5m A regulation Ripple rejection ratio R.R. 1 V rms, f = 120 Hz, IOUT = 10 mA 58 66 ¾ dB Minimum input and V DIF(min)1 V IN = 3.2 V, IOUT = 0 mA ¾ 0.1 0.2 V output voltage difference 1 Minimum input and V DIF(min)2 V IN = 3.6 V, IOUT = 150 mA ¾¾ 0.4 V output voltage difference 2 Control terminal threshold high voltageV CONTH V IN = 4.5 V, IOUT = 50 mA ¾¾ 1.50 V Control terminal threshold high voltageV CONTH V IN = 4.5 V, IOUT = 50 mA 0.30 ¾¾ V Control terminal current I CONT V IN = 4.5 V, IOUT = 50 mA ¾¾ 30 mA V CONT = 1.8 V

Design reference data Note) The following values are typical and not guaranteed values. Parameter Symbol Conditions Min Typ Max Unit Output noise voltage V NO 10Hz £ f £ 100kHz, IOUT = 10 mA ¾ 72 ¾m V Output voltage temperature 1 ɾ dVOUT V IN = 4.5 V, IOUT = 0 mA ¾ 90 ¾ ppm/°C coefficient V OUT dT - 30°C £ Ta £ + 85°C Output rise time t ON V IN = 4.5 V, IOUT = 50 mA ¾ 0.12 ¾ ms V CONT = 0 V ﬁ 1.8 V, CIN = 0.1 mF C OUT = 10 mF, VOUT = 90% Note) *1 : 1.0 W *2 : Peak output current : The output current when the output voltage has been decreased by 5% from the value at the time of the output current is 50 mA due to the overcurrent protection. n Electrical Characteristics at Ta = 25°C Note) Unless otherwise specially provided, shorten each test time (within 10 ms) so that the test is conducted under the condition that the drift due to the temperature increase in the chip junction part can be neglected. CIN = 0.1 mF, COUT = 10 mF n Recommended Operating Range AN80L35RMS (3.5 V) Note) *1 : Refer to n Technical Information " • Output rise time characteristics".

AN80LXXRMS Series Voltage Regulators Parameter Symbol Range Unit Supply voltage V CC 4.0 to 14.5 V Parameter Symbol Conditions Min Typ Max Unit Output voltage V OUT V IN = 4.6 V, IOUT = 50 mA 3.492 3.6 3.708 V Input stability 1 REG IN1 V IN = 4.6 V ﬁ 14.5 V, IOUT = 50 mA ¾ 10 50 mV Input stability 2 REG IN2 V IN = 4.6 V ﬁ 9 V, IOUT = 50 mA ¾ 52 0 m V Load stability *1 REG LOA V IN = 4.6 V, IOUT = 0 mA ﬁ 150 mA ¾ 50 150 mV Peak output current *2 IPEAK V IN = 4.6 V, The output current value 180 240 ¾ mA decreases by 5% from the value when V OUT is at IOUT = 50 mA. Bias current without load I BIAS V IN = 4.6 V, IOUT = 0 mA ¾¾ 350 mA Bias current fluctuation with loadDIBIAS V IN = 4.6 V, IOUT = 0 mA ﬁ 150 mA ¾¾ 5m A Standby consumption current I STB V IN = 10 V, VCONT = 0 V ¾¾ 0.1 mA Bias current before starting IRUSH V IN = 3.3 V, IOUT = 0 mA ¾1 . 5 5m A regulation Ripple rejection ratio R.R. 1 V rms, f = 120 Hz, IOUT = 10 mA 58 66 ¾ dB Minimum input and V DIF(min)1 V IN = 3.3 V, IOUT = 0 mA ¾ 0.1 0.2 V output voltage difference 1 Minimum input and V DIF(min)2 V IN = 3.7 V, IOUT = 150 mA ¾¾ 0.4 V output voltage difference 2 Control terminal threshold high voltageV CONTH V IN = 4.6 V, IOUT = 50 mA ¾¾ 1.50 V Control terminal threshold high voltageV CONTH V IN = 4.6 V, IOUT = 50 mA 0.30 ¾¾ V Control terminal current I CONT V IN = 4.6 V, IOUT = 50 mA ¾¾ 30 mA V CONT = 1.8 V

Design reference data Note) The following values are typical and not guaranteed values. Parameter Symbol Conditions Min Typ Max Unit Output noise voltage V NO 10Hz £ f £ 100kHz, IOUT =10 mA ¾ 74 ¾m V Output voltage temperature 1 ɾ dV OUT V IN = 4.6 V, IOUT = 0 mA ¾ 90 ¾ ppm/°C coefficient V OUT dT - 30°C £ Ta £ + 85°C Output rise time t ON V IN = 4.6 V, IOUT = 50 mA ¾ 0.12 ¾ ms V CONT = 0 V ﬁ 1.8 V, CIN = 0.1 mF C OUT = 10 mF, VOUT = 90% Note) *1 : 1.0 W *2 : Peak output current : The output current when the output voltage has been decreased by 5% from the value at the time of the output current is 50 mA due to the overcurrent protection. n Electrical Characteristics at Ta = 25°C Note) Unless otherwise specially provided, shorten each test time (within 10 ms) so that the test is conducted under the condition that the drift due to the temperature increase in the chip junction part can be neglected. CIN = 0.1 mF, COUT = 10 mF n Recommended Operating Range AN80L36RMS (3.6 V) Note) *1 : Refer to n Technical Information " • Output rise time characteristics".

Voltage Regulators AN80LXXRMS Series Parameter Symbol Range Unit Supply voltage V CC 5.2 to 14.5 V Parameter Symbol Conditions Min Typ Max Unit Output voltage V OUT V IN = 5.8 V, IOUT = 50 mA 4.656 4.8 4.944 V Input stability 1 REG IN1 V IN = 5.8 V ﬁ 14.5 V, IOUT = 50 mA ¾ 10 50 mV Input stability 2 REG IN2 V IN = 5.8 V ﬁ 9 V, IOUT = 50 mA ¾ 52 0 m V Load stability *1 REG LOA V IN = 5.8 V, IOUT = 0 mA ﬁ 150 mA ¾ 50 150 mV Peak output current *2 IPEAK V IN = 5.8 V, The output current value 180 240 ¾ mA decreases by 5% from the value when V OUT is at IOUT = 50 mA. Bias current without load I BIAS V IN = 5.8 V, IOUT = 0 mA ¾¾ 350 mA Bias current fluctuation with loadDIBIAS V IN = 5.8 V, IOUT = 0 mA ﬁ 150 mA ¾¾ 5m A Standby consumption current I STB V IN = 10 V, VCONT = 0 V ¾¾ 0.1 mA Bias current before starting IRUSH V IN = 4.5 V, IOUT = 0 mA ¾ 1.5 5m A regulation Ripple rejection ratio R.R. 1 V rms, f = 120 Hz, IOUT = 10 mA 57 65 ¾ dB Minimum input and V DIF(min)1 V IN = 4.5 V, IOUT = 0 mA ¾ 0.1 0.2 V output voltage difference 1 Minimum input and V DIF(min)2 V IN = 4.9 V, IOUT = 150 mA ¾¾ 0.4 V output voltage difference 2 Control terminal threshold high voltageV CONTH V IN = 5.8 V, IOUT = 50 mA ¾¾ 1.50 V Control terminal threshold high voltageV CONTH V IN = 5.8 V, IOUT = 50 mA 0.30 ¾¾ V Control terminal current I CONT V IN = 5.8 V, IOUT = 50 mA ¾¾ 30 mA V CONT = 1.8 V

Design reference data Note) The following values are typical and not guaranteed values. Parameter Symbol Conditions Min Typ Max Unit Output noise voltage V NO 10Hz £ f £ 100kHz, IOUT = 10 mA ¾ 100 ¾m V Output voltage temperature 1 ɾ dVOUT V IN = 5.8 V, IOUT = 0 mA ¾ 90 ¾ ppm/°C coefficient V OUT dT - 30°C £ Ta £ + 85°C Output rise time t ON V IN = 5.8 V, IOUT = 50 mA ¾ 0.20 ¾ ms V CONT = 0 V ﬁ 1.8 V, CIN = 0.1 mF C OUT = 10 mF, VOUT = 90% Note) *1 : 1.0 W *2 : Peak output current : The output current when the output voltage has been decreased by 5% from the value at the time of the output current is 50 mA due to the overcurrent protection. n Electrical Characteristics at Ta = 25°C Note) Unless otherwise specially provided, shorten each test time (within 10 ms) so that the test is conducted under the condition that the drift due to the temperature increase in the chip junction part can be neglected. CIN = 0.1 mF, COUT = 10 mF n Recommended Operating Range AN80L48RMS (4.8 V) Note) *1 : Refer to n Technical Information " • Output rise time characteristics".

AN80LXXRMS Series Voltage Regulators Parameter Symbol Range Unit Supply voltage V CC 5.3 to 14.5 V Parameter Symbol Conditions Min Typ Max Unit Output voltage V OUT V IN = 5.9 V, IOUT = 50 mA 4.753 4.9 5.047 V Input stability 1 REG IN1 V IN = 5.9 V ﬁ 14.5 V, IOUT = 50 mA ¾ 10 50 mV Input stability 2 REG IN2 V IN = 5.9 V ﬁ 9 V, IOUT = 50 mA ¾ 52 0 m V Load stability *1 REG LOA V IN = 5.9 V, IOUT = 0 mA ﬁ 150 mA ¾ 50 150 mV Peak output current *2 IPEAK V IN = 5.9 V, The output current value 180 240 ¾ mA decreases by 5% from the value when V OUT is at IOUT = 50 mA. Bias current without load I BIAS V IN = 5.9 V, IOUT = 0 mA ¾¾ 350 mA Bias current fluctuation with loadDIBIAS V IN = 5.9 V, IOUT = 0 mA ﬁ 150 mA ¾¾ 5m A Standby consumption current I STB V IN = 10 V, VCONT = 0 V ¾¾ 0.1 mA Bias current before starting IRUSH V IN = 4.6 V, IOUT = 0 mA ¾1 . 5 5m A regulation Ripple rejection ratio R.R. 1 V rms, f = 120 Hz, IOUT = 10 mA 57 65 ¾ dB Minimum input and V DIF(min)1 V IN = 4.6 V, IOUT = 0 mA ¾ 0.1 0.2 V output voltage difference 1 Minimum input and V DIF(min)2 V IN = 5.0 V, IOUT = 150 mA ¾¾ 0.4 V output voltage difference 2 Control terminal threshold high voltageV CONTH V IN = 5.9 V, IOUT = 50 mA ¾¾ 1.50 V Control terminal threshold high voltageV CONTH V IN = 5.9 V, IOUT = 50 mA 0.30 ¾¾ V Control terminal current I CONT V IN = 5.9 V, IOUT = 50 mA ¾¾ 30 mA V CONT = 1.8 V

Design reference data Note) The following values are typical and not guaranteed values. Parameter Symbol Conditions Min Typ Max Unit Output noise voltage V NO 10Hz £ f £ 100kHz, IOUT =10 mA ¾ 102 ¾m V Output voltage temperature 1 ɾ dV OUT V IN = 5.9 V, IOUT = 0 mA ¾ 90 ¾ ppm/°C coefficient V OUT dT - 30°C £ Ta £ + 85°C Output rise time t ON V IN = 5.9 V, IOUT = 50 mA ¾ 0.20 ¾ ms V CONT = 0 V ﬁ 1.8 V, CIN = 0.1 mF C OUT = 10 mF, VOUT = 90% Note) *1 : 1.0 W *2 : Peak output current : The output current when the output voltage has been decreased by 5% from the value at the time of the output current is 50 mA due to the overcurrent protection. n Electrical Characteristics at Ta = 25°C Note) Unless otherwise specially provided, shorten each test time (within 10 ms) so that the test is conducted under the condition that the drift due to the temperature increase in the chip junction part can be neglected. CIN = 0.1 mF, COUT = 10 mF n Recommended Operating Range AN80L49RMS (4.9 V) Note) *1 : Refer to n Technical Information " • Output rise time characteristics".

Voltage Regulators AN80LXXRMS Series Parameter Symbol Range Unit Supply voltage V CC 5.4 to 14.5 V Parameter Symbol Conditions Min Typ Max Unit Output voltage V OUT V IN = 6.0 V, IOUT = 50 mA 4.850 5.0 5.150 V Input stability 1 REG IN1 V IN = 6.0 V ﬁ 14.5 V, IOUT = 50 mA ¾ 10 50 mV Input stability 2 REG IN2 V IN = 6.0 V ﬁ 9 V, IOUT = 50 mA ¾ 52 0 m V Load stability *1 REG LOA V IN = 6.0 V, IOUT = 0 mA ﬁ 150 mA ¾ 50 150 mV Peak output current *2 IPEAK V IN = 6.0 V, The output current value 180 240 ¾ mA decreases by 5% from the value when V OUT is at IOUT = 50 mA. Bias current without load I BIAS V IN = 6.0 V, IOUT = 0 mA ¾¾ 350 mA Bias current fluctuation with loadDIBIAS V IN = 6.0 V, IOUT = 0 mA ﬁ 150 mA ¾¾ 5m A Standby consumption current I STB V IN = 10 V, VCONT = 0 V ¾¾ 0.1 mA Bias current before starting IRUSH V IN = 4.7 V, IOUT = 0 mA ¾ 1.5 5m A regulation Ripple rejection ratio R.R. 1 V rms, f = 120 Hz, IOUT = 10 mA 56 64 ¾ dB Minimum input and V DIF(min)1 V IN = 4.7 V, IOUT = 0 mA ¾ 0.1 0.2 V output voltage difference 1 Minimum input and V DIF(min)2 V IN = 5.1 V, IOUT = 150 mA ¾¾ 0.4 V output voltage difference 2 Control terminal threshold high voltageV CONTH V IN = 6.0 V, IOUT = 50 mA ¾¾ 1.50 V Control terminal threshold high voltageV CONTH V IN = 6.0 V, IOUT = 50 mA 0.30 ¾¾ V Control terminal current I CONT V IN = 6.0 V, IOUT = 50 mA ¾¾ 30 mA V CONT = 1.8 V

Design reference data Note) The following values are typical and not guaranteed values. Parameter Symbol Conditions Min Typ Max Unit Output noise voltage V NO 10Hz £ f £ 100kHz, IOUT = 10 mA ¾ 104 ¾m V Output voltage temperature 1 ɾ dVOUT V IN = 6.0 V, IOUT = 0 mA ¾ 90 ¾ ppm/°C coefficient V OUT dT - 30°C £ Ta £ + 85°C Output rise time t ON V IN = 6.0 V, IOUT = 50 mA ¾ 0.20 ¾ ms V CONT = 0 V ﬁ 1.8 V, CIN = 0.1 mF C OUT = 10 mF, VOUT = 90% Note) *1 : 1.0 W *2 : Peak output current : The output current when the output voltage has been decreased by 5% from the value at the time of the output current is 50 mA due to the overcurrent protection. n Electrical Characteristics at Ta = 25°C Note) Unless otherwise specially provided, shorten each test time (within 10 ms) so that the test is conducted under the condition that the drift due to the temperature increase in the chip junction part can be neglected. CIN = 0.1 mF, COUT = 10 mF n Recommended Operating Range AN80L50RMS (5.0 V) Note) *1 : Refer to n Technical Information " • Output rise time characteristics".

AN80LXXRMS Series Voltage Regulators Parameter Symbol Range Unit Supply voltage V CC 5.5 to 14.5 V Parameter Symbol Conditions Min Typ Max Unit Output voltage V OUT V IN = 6.1 V, IOUT = 50 mA 4.947 5.1 5.253 V Input stability 1 REG IN1 V IN = 6.1 V ﬁ 14.5 V, IOUT = 50 mA ¾ 10 50 mV Input stability 2 REG IN2 V IN = 6.1 V ﬁ 9 V, IOUT = 50 mA ¾ 52 0 m V Load stability *1 REG LOA V IN = 6.1 V, IOUT = 0 mA ﬁ 150 mA ¾ 50 150 mV Peak output current *2 IPEAK V IN = 6.1 V, The output current value 180 240 ¾ mA decreases by 5% from the value when V OUT is at IOUT = 50 mA. Bias current without load I BIAS V IN = 6.1 V, IOUT = 0 mA ¾¾ 350 mA Bias current fluctuation with loadDIBIAS V IN = 6.1 V, IOUT = 0 mA ﬁ 150 mA ¾¾ 5m A Standby consumption current I STB V IN = 10 V, VCONT = 0 V ¾¾ 0.1 mA Bias current before starting IRUSH V IN = 4.8 V, IOUT = 0 mA ¾1 . 5 5m A regulation Ripple rejection ratio R.R. 1 V rms, f = 120 Hz, IOUT = 10 mA 56 64 ¾ dB Minimum input and V DIF(min)1 V IN = 4.8 V, IOUT = 0 mA ¾ 0.1 0.2 V output voltage difference 1 Minimum input and V DIF(min)2 V IN = 5.2 V, IOUT = 150 mA ¾¾ 0.4 V output voltage difference 2 Control terminal threshold high voltageV CONTH V IN = 6.1 V, IOUT = 50 mA ¾¾ 1.50 V Control terminal threshold high voltageV CONTH V IN = 6.1 V, IOUT = 50 mA 0.30 ¾¾ V Control terminal current I CONT V IN = 6.1 V, IOUT = 50 mA ¾¾ 30 mA V CONT = 1.8 V

Design reference data Note) The following values are typical and not guaranteed values. Parameter Symbol Conditions Min Typ Max Unit Output noise voltage V NO 10Hz £ f £ 100kHz, IOUT =10 mA ¾ 106 ¾m V Output voltage temperature 1 ɾ dV OUT V IN = 6.1 V, IOUT = 0 mA ¾ 90 ¾ ppm/°C coefficient V OUT dT - 30°C £ Ta £ + 85°C Output rise time t ON V IN = 6.1panpa V, IOUT = 50 mA ¾ 0.20 ¾ ms V CONT = 0 V ﬁ 1.8 V, CIN = 0.1 mF C OUT = 10 mF, VOUT = 90% Note) *1 : 1.0 W *2 : Peak output current : The output current when the output voltage has been decreased by 5% from the value at the time of the output current is 50 mA due to the overcurrent protection. n Electrical Characteristics at Ta = 25°C Note) Unless otherwise specially provided, shorten each test time (within 10 ms) so that the test is conducted under the condition that the drift due to the temperature increase in the chip junction part can be neglected. CIN = 0.1 mF, COUT = 10 mF n Recommended Operating Range AN80L51RMS (5.1 V) Note) *1 : Refer to n Technical Information " • Output rise time characteristics".

Voltage Regulators AN80LXXRMS Series Parameter Symbol Range Unit Supply voltage V CC 5.6 to 14.5 V Parameter Symbol Conditions Min Typ Max Unit Output voltage V OUT V IN = 6.2 V, IOUT = 50 mA 5.044 5.2 5.356 V Input stability 1 REG IN1 V IN = 6.2 V ﬁ 14.5 V, IOUT = 50 mA ¾ 10 50 mV Input stability 2 REG IN2 V IN = 6.2 V ﬁ 9 V, IOUT = 50 mA ¾ 52 0 m V Load stability *1 REG LOA V IN = 6.2 V, IOUT = 0 mA ﬁ 150 mA ¾ 50 150 mV Peak output current *2 IPEAK V IN = 6.2 V, The output current value 180 240 ¾ mA decreases by 5% from the value when V OUT is at IOUT = 50 mA. Bias current without load I BIAS V IN = 6.2 V, IOUT = 0 mA ¾¾ 350 mA Bias current fluctuation with loadDIBIAS V IN = 6.2 V, IOUT = 0 mA ﬁ 150 mA ¾¾ 5m A Standby consumption current I STB V IN = 10 V, VCONT = 0 V ¾¾ 0.1 mA Bias current before starting IRUSH V IN = 4.9 V, IOUT = 0 mA ¾ 1.5 5m A regulation Ripple rejection ratio R.R. 1 V rms, f = 120 Hz, IOUT = 10 mA 56 64 ¾ dB Minimum input and V DIF(min)1 V IN = 4.9 V, IOUT = 0 mA ¾ 0.1 0.2 V output voltage difference 1 Minimum input and V DIF(min)2 V IN = 5.3 V, IOUT = 150 mA ¾¾ 0.4 V output voltage difference 2 Control terminal threshold high voltageV CONTH V IN = 6.2 V, IOUT = 50 mA ¾¾ 1.50 V Control terminal threshold high voltageV CONTH V IN = 6.2 V, IOUT = 50 mA 0.30 ¾¾ V Control terminal current I CONT V IN = 6.2 V, IOUT = 50 mA ¾¾ 30 mA V CONT = 1.8 V

Design reference data Note) The following values are typical and not guaranteed values. Parameter Symbol Conditions Min Typ Max Unit Output noise voltage V NO 10Hz £ f £ 100kHz, IOUT = 10 mA ¾ 108 ¾m V Output voltage temperature 1 ɾ dVOUT V IN = 6.2 V, IOUT = 0 mA ¾ 90 ¾ ppm/°C coefficient V OUT dT - 30°C £ Ta £ + 85°C Output rise time t ON V IN = 6.2 V, IOUT = 50 mA ¾ 0.20 ¾ ms V CONT = 0 V ﬁ 1.8 V, CIN = 0.1 mF C OUT = 10 mF, VOUT = 90% Note) *1 : 1.0 W *2 : Peak output current : The output current when the output voltage has been decreased by 5% from the value at the time of the output current is 50 mA due to the overcurrent protection. n Electrical Characteristics at Ta = 25°C Note) Unless otherwise specially provided, shorten each test time (within 10 ms) so that the test is conducted under the condition that the drift due to the temperature increase in the chip junction part can be neglected. CIN = 0.1 mF, COUT = 10 mF n Recommended Operating Range AN80L52RMS (5.2 V) Note) *1 : Refer to n Technical Information " • Output rise time characteristics".

AN80LXXRMS Series Voltage Regulators AN80LXXRMS series Technical Information and etc. n Technical Information

PD ¾ Ta curves of Mini-type 5-pin package (Common to AN80LXXRMS series) PD ¾ Ta
ESR characteristics (Common to AN80LXXRMS series) 0.000 Power dissipation PD (W) Ambient temperature Ta (°C) 25 50 75 100 125 150 0.100 0.200 0.150 0.300 0.400 0.500 Standard board mounting (Glass epoxy board : 50 · 50 · t1.6 mm3) R th(j-a) = 416.6°C/W Independent IC without heat sink R th(j-a) = 833.3°C/W ESR (W ) C OUT (mF) 0.1 1 10 100 Stable Oscillation

Voltage Regulators AN80LXXRMS Series n Technical Information (continued)

ESR characteristics (Common to AN80LXXRMS series) Test circuit Note) 1. Not guaranteed values 2. The capacitance value used for COUT must be 0.22 mF or more and 100 mF or less. The recommended value is 10 mF. 3. Use a capacitor having ESR (equivalent series resistance of capacitor) of 35 W or less (at Ta = - 30°C to + 85°C).
Output rise-time characteristics (Common to AN80LXXRMS series)
Output voltage - temperature characteristics examples <AN80L18RMS > GND IN OUT N.C. C OUT ESR CONT 0 V to 14.5 V Load resistance (0 mA to 150 mA) CONT 1.8 V 0 V V OUT V OUT : 90% tON Time Temperature Ta (°C) Output voltage VOUT (V) 1.71 1.73 1.75 1.77 1.79 1.81 1.83 1.85 1.87 1.89 -40 -30 -20 -1 0 0 1 02 03 04 05 06 07 08 09 0 IOUT = 0 mA IOUT = 50 mAIOUT = 150 mA Input voltage : 2.8 V Temperature Ta (°C) Output voltage VOUT (V) 1.71 1.73 1.75 1.77 1.79 1.81 1.83 1.85 1.87 1.89 -40 -30 -20 -1 0 0 1 02 03 04 05 06 07 08 09 0 IOUT = 0 mA IOUT = 50 mAIOUT = 150 mA Input voltage : 9.0 V

AN80LXXRMS Series Voltage Regulators Temperature Ta (°C) Output voltage VOUT (V) Input voltage : 9.0 V 3.135 3.185 3.235 3.285 3.335 3.385 3.435 -40 -30 -20 -1 0 0 1 02 03 04 05 06 07 08 09 0 IOUT = 0 mA IOUT = 50 mAIOUT = 150 mA Temperature Ta (°C) Output voltage VOUT (V) Input voltage : 4.3 V 3.135 3.185 3.235 3.285 3.335 3.385 3.435 -40 -30 -20 -1 0 0 1 02 03 04 05 06 07 08 09 0 IOUT = 0 mA IOUT = 50 mAIOUT = 150 mA Temperature Ta (°C) Output voltage VOUT (V) Input voltage : 3.0 V 1.9 1.95 2.05 2.1 -40 -30 -20 -1 0 0 1 02 03 04 05 06 07 08 09 0 IOUT = 0 mA IOUT = 50 mAIOUT = 150 mA Temperature Ta (°C) Output voltage VOUT (V) Input voltage : 9.0 V 1.9 1.95 2.05 2.1 -40 -30 -20 -1 0 0 1 02 03 04 05 06 07 08 09 0 IOUT = 0 mA IOUT = 50 mAIOUT = 150 mA n Technical Information (continued)

Output voltage - temperature characteristics examples (continued) <AN80L20RMS > <AN80L33RMS > n Application Circuit Example (Common to AN80LXXRMS Series) N.C. In 10 mF Out 10 mF Output off when Low Output on when High

Product Information

AN80L35RMS specifications and overview.

Summary

Low-drop type positive output voltage regulator IC

Description

Low-drop type positive output voltage regulator IC

Source title AN80L35RMS Datasheet(PDF) - Panasonic Semiconductor

Related Parts

More parts from the same family.

Browse manufacturer