AN6095SH

AN6095SH PANASONIC | Alldatasheet

Document overview

• Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
• PDF pages: 10

Technical content

ICs for Mobile Communication 1Publication date: December 2001 SDM00003BEB AN6095SH Reception IF + transmission quadrature modulation IC for PHS and cellular telephone I Overview The AN6095SH is a single chip IC for PHS reception IF block and transmission block. Reception IF block is incorporating a 2nd down-mixer and a limiter/RSSI circuit which can operate for up to 300 MHz of input frequency. Transmission block is in- corporating a quadrature modulator, a phase shifter, an up-mixer for 1.9 GHz and output level control functions. It contributes to realization of small package and small size of equipment. I Features

• Operating supply voltage range: 2.7 V to 4.0 V
• Current consumption Transmission block: 28 mA Reception block: 5.3 mA Sleep mode: 10 µA or less (Transmission block)
• Output level: −8 dBm
• Output frequency: up to 2 GHz
• Transmission IF frequency: 100 MHz to 300 MHz (Reception block)
• RSSI input D range: 80 dB
• Mixer conversion gain: 16 dB
• Limiter voltage gain: 70 dB
• 2nd down-mixer NF: 6 dB I Applications
• PHS SSOP024-P-0300A Unit: mm 5.5±0.3 7.5±0.3 (0.5) 0.1±0.1 0.15+0.1 -0.05 0.65±0.1 1.5±0.2 0.65±0.1 6.5±0.3 0.50.2±0.1 I Block Diagram Io Io Io Io RSSI Σ φ Note) The package of this product will be changed to lead-free type (SSOP024-P-0300D). See the new package dimensions section later of this datasheet.

2 SDM00003BEB

Pin No. Symbol Description

1 RXMXIN RX-mixer-in

2 RXLOIN RX-local-in

3 VCCM V CC-mixer

4 MXO Mixer-out

5 LMDEC1 Limiter-decouple 1

6 LMIN Limiter-in

7 LMDEC2 Limiter-decouple 2

8 GNDR GND-RX

9 VCCL V CC -limiter

10 LMO Limiter-out

11 TXLO1 TX-local 1-in

12 RSO RSSI-out

Pin No. Symbol Description

13 Q-IN Q-input

14 Q-IN Q-input

15 I-IN I-input

16 I-IN I-input

17 GNDM GND-TX-modulator

18 APC/BS APC/BS

19 VCCM V CC -TX-modulator

20 TXLO2R TX-local 2-REF

21 TXLO2 TX-local 2

22 VCCO V CC -TX-out

23 GNDO GND-TX-out

24 TXO TX-output

Note) 1. *: Except for the operating ambient temperature and storage temperature, all ratings are for Ta = 25°C. 2. For the main characteristics, refer to " I Technical Data". I Absolute Maximum Ratings Parameter Symbol Rating Unit Supply voltage V CC 4.2 V Supply current I CC 60 mA Power dissipation P D 252 mW Operating ambient temperature * Topr −20 to +60 °C Storage temperature * Tstg −55 to +125 °C I Recommended Operating Range Parameter Symbol Range Unit Supply voltage V CC 2.7 to 4.0 V

I Electrical Characteristics at Ta = 25°C Parameter Symbol Conditions Min Typ Max Unit Current consumption I CCRX No signal  5.3 6.8 mA (reception) Mixer conversion gain G MX VMI = 70 dBµ 13 16 19 dB Except for filter loss, SW1 = a Mixer maximum output level V MX VMI = 105 dBµ 105 110  dBµ Except for filter loss, SW1 = a Limiter voltage gain G LM VLI = 20 dBµ, SW1 = b 6 36 87 3 d B Limiter maximum output V LM VLI = 80 dBµ, SW1 = b 300 360  mV[p-p] amplitude RSSI output voltage 1 V S(1) No signal, SW1 = b 0 0.2 0.5 V RSSI output voltage 2 V S(2) VLI = 115 dBµ, SW1 = b 1.60 1.80  V RSSI output slope D S VS (VIS) = VS(1) + 0.15 V 1.0 1.25 1.5 V DS(1) = VS (VIS + 65 dBµ) − VS (VIS) SW1 = b RSSI output slope variation ∆DS(n) ∆DS(n) = 5 {VS (VIS + n13 dBµ) − 0.75 1.0 1.25  VS (VIS + (n−1) 13 dBµ)} /DS(1) n = 1 to 5, SW1 = b Current consumption I CCTX Lo1 = 233.15 MHz, −10 dBm  28 37 mA (transmission) Lo2 = 1 672.5 MHz, −10 dBm VAPC = 2.75 V Sleep current at transmission I SL No signal, VAPC = 0 V  01 0 µA Transmission output level 1 P O1 Lo1 = 233.15 MHz, −10 dBm −12 −8  dBm Lo2 = 1 660 MHz, −10 dBm VAPC = 2.75 V Transmission output level 2 P O2 Lo1 = 233.15 MHz, −10 dBm −12 −8  dBm Lo2 = 1 685 MHz, −10 dBm VAPC = 2.75 V Note) 1. Refer to the " • Test circuit" for the SW1. 2. Unless otherwise specified : At reception, VCC2 = 3.0 V, VLO3 = −10 dBm: f = 233.15 MHz, VMI: f = 243.95 MHz, SW1 = a VLI: f = 10.8 MHz (Input level of pin 6 except for attenuation of the matching circuit and filter.) VMO and VLO are in high impedance measurement. (V LM is measured with probe load of 27 pF and 1 M Ω.) VIS is an input level V LI at which RSSI output voltage becomes V S(1) + 0.15 V. At transmission, VCC1 = 3.0 V, IQ signal amplitude: 0.4 V (both phases), DC bias: 1.5 V, SW1 = a ICCTX: π/4 QPSK-modulated, PO1 and PO2: PN9 stages modulated wave Output frequency of P O1: 1 893.174 MHz Output frequency of P O2: 1 918.174 MHz

4 SDM00003BEB

I Electrical Characteristics at Ta = 25°C (continued)

• Design reference data Note) The characteristics listed below are theoretical values based on the IC design and are not guaranteed. Parameter Symbol Conditions Min Typ Max Unit 1st local leak suppression CL1 Lo1 = 233.15 MHz, −10 dBm − 25  dBc amount Lo2 = 1 672.5 MHz, −10 dBm VAPC = 2.75 V 2nd local leak suppression CL2 Lo1 = 233.15 MHz, −10 dBm − 15  dBc amount Lo2 = 1 672.5 MHz, −10 dBm VAPC = 2.75 V In-band output level deviation ∆P Lo1 = 233.15 MHz, −10 dBm ± 1.6  dB Lo2 = 1 660 to 1 685 MHz, −10 dBm VAPC = 2.75 V Adjacent channel leak power BL1 Lo1 = 233.15 MHz, −10 dBm − 65 −60 dBc suppression (600 kHz detuning) Lo2 = 1 672.5 MHz, −10 dBm VAPC = 2.75 V Modulation precision EVM Lo1 = 233.15 MHz, −10 dBm  35 %[rms] Lo2 = 1 672.5 MHz, −10 dBm VAPC = 2.75 V Minimum output level P min Lo1 = 233.15 MHz, −10 dBm − 45 −40 dBm Lo2 = 1 672.5 MHz, −10 dBm VAPC = 1.0 V Image leak suppression IL1 Lo1 = 233.15 MHz, −10 dBm − 35  dBc Lo2 = 1 672.5 MHz, −10 dBm VAPC = 2.75 V IQ: Level is of no adjustment fLO1 + fLO2 CL Lo1 = 233.15 MHz, −10 dBm − 35  dBc local leak suppression amount Lo2 = 1 672.5 MHz, −10 dBm VAPC = 2.75 V IQ: DC offset is of no adjustment Proximity spurious suppression DU Lo1 = 233.15 MHz, −10 dBm − 55 −51 dBc Lo2 = 1 672.5 MHz, −10 dBm Adjust VAPC so as to get PO = −12 dBm Note) Unless otherwise specified: At transmission, VCC1 = 3.0 V, SW1 = a IQ signal: 0.4 V[p-p] (both phases), DC bias: 1.5 V CL1, CL2, ∆P, BL1, EVM, Pmin , DU: PN9 stages modulated wave IL1, CL: π/4 QPSK-modulated

I Electrical Characteristics (continued)

• Test circuit 100 pF 1 kΩ Q 100 pF 1 kΩ Q 100 pF 1 kΩ I VAPC /BS VCC1 Lo 2 100 pF 4 700 pF 1 000 pF 1 000 pF 100 pF 1 000 pF 2 200 pF 2 200 pF 22 nF 100 pF 560 pF22 nF 1 000 pF

10.8 MHz

1 kΩ 560 Ω 47 Ω 560 Ω I 5 µF PO Lo 3 100 pF VMI VLI Lo 1 VMO VLM 5 µF VCC2 Vs 47 Ω 47 Ω 47 Ω 330 Ω 47 Ω SW 1 a b Io Io Io Io RSSI Σ φ

6 SDM00003BEB

Unless otherwise specified, the test condition is the same as "I Electrical Characteristics". Characteristics are the theoretical values and not guaranteed ones.

• Main characteristics (application circuit) Wide band spurious characteristic IM/mixer output  Mixer input 06 G −10 −20 −30 −40 −50 −60 −70 −80 −90 −100 Frequency (Hz) Transmission output spurious level (dBm) Mixer CG, NF characteristics  Local input Limiter input/output characteristic 0 1 02 03 04 05 06 07 08 09 0 1 0 0 1 1 0 1 2 0 1 3 0 120 130 110 100 Mixer input level (dBµ) IM/mixer output level (dBµ) IM output Mixer output Local input level (dBm) Mixer CG (dB) NF (dB) CG NF RSSI characteristic Mixer inpit/output characteristics −1 00 1 02 03 04 05 06 07 08 09 0 1 0 0 1 1 0 1 2 0 120 110 100 Mixer input level (dBµ) Limiter output level (dBµ) 0 1 02 03 04 05 06 07 08 09 0 1 0 0 1 1 0 1 2 0 1 3 0 120 110 100 Mixer input level (dBµ) Mixer output level (dBµ) Ta = 25°C, 60°C Ta = −20°C −1 00 1 02 03 04 05 06 07 08 09 0 1 0 0 1 1 0 1.8 1.6 1.4 1.2 1.0 0.8 0.6 0.4 0.2 0.0 Mixer input level (dBµ) RSSI output level (V)

I Technical Data (continued)

• Main characteristics (application circuit) (continued) Limiter characteristics RSSI characteristics 0 1 02 03 04 05 06 07 08 09 0 1 0 0 1 1 0 1 2 0 120 110 100 Limiter input level (dBµ) Limiter output level (dBµ) Ta = −20°C Ta = 60°C Ta = 25°C 0 1 02 03 04 05 06 07 08 09 0 1 0 0 1 1 0 1 2 0 1.4 1.2 1.0 0.8 2.2 2.0 1.8 1.6 0.6 0.4 0.2 0.0 Limiter input level (dBµ) RSSI output level (V) Ta = −20°C Ta = 60°C Ta = 25°C APC control voltage characteristics 03 12 −10 −20 −30 −40 −50 −60 −70 −80 −90 −100 EVM (%[rms])10 Output level 8fLO1Ta = 25°C Ta = −20°C Ta = −20°C Ta = −20°C Ta = 60°C 60°C 60°C 60°C 25°C 25°C 25°C EVM ACP 600 kHz Ta = −20°C Output level (dBm) 8fLO1 , adjacent channel leak (600 kHz) (dBc) APC control voltage (V) VCC = 3.0 V Lo1: 233.15 MHz, −10 dBm Lo2: 1 672.5 MHz, −10 dBm IQ: 0.4 V[p-p] (double phase), 1.5 V DC , using PN9 stages continuous wave

8 SDM00003BEB

I Application Circuit Example 100 pF 1 kΩ Q 100 pF 1 kΩ Q 100 pF 1 kΩ I VAPC /BS VCC1 Lo 2 100 pF 4 700 pF 1 000 pF 1 000 pF 100 pF 470 pF 1 pF 1 000 pF 2 200 pF 2 200 pF 100 pF 560 pF22 nF 1 000 pF 1.8 nH 120 nH 47 nH 100 pF 100 pF 2 200 pF 1 kΩ 560 Ω 47 Ω 560 Ω I 5 µF PO Lo 3 Lo 1 VMI VMO VLM 5 µF VCC2 Vs 47 Ω 47 Ω 22 nF 270 Ω 22 nF IO IO IO IO RSSI Σ φ At CG/NF measurement, set pin 4 output as the right figure.

I New Package Dimensions (Unit: mm)

• SSOP024-P-0300D (Lead-free package) 5.50±0.30 7.50±0.30 1.50±0.200.10±0.10 6.50±0.30 0.20+0.10 -0.05 0.15 +0.10 -0.05 0° to 10° 1324 121 (1.00) (0.50) Seating plane Seating plane (0.50) 0.50

Please read the following notes before using the datasheets A. These materials are intended as a reference to assist customers with the selection of Panasonic semiconductor products best suited to their applications. Due to modification or other reasons, any information contained in this material, such as available product types, technical data, and so on, is subject to change without notice. Customers are advised to contact our semiconductor sales office and obtain the latest information before starting precise technical research and/or purchasing activities. B. Panasonic is endeavoring to continually improve the quality and reliability of these materials but there is always the possibility that further rectifications will be required in the future. Therefore, Panasonic will not assume any liability for any damages arising from any errors etc. that may ap- pear in this material. C. These materials are solely intended for a customer's individual use. Therefore, without the prior written approval of Panasonic, any other use such as reproducing, selling, or distributing this material to a third party, via the Internet or in any other way, is prohibited. Request for your special attention and precautions in using the technical information and semiconductors described in this material (1) An export permit needs to be obtained from the competent authorities of the Japanese Govern- ment if any of the products or technologies described in this material and controlled under the "Foreign Exchange and Foreign Trade Law" is to be exported or taken out of Japan. (2) The technical information described in this material is limited to showing representative character- istics and applied circuit examples of the products. It does not constitute the warranting of industrial property, the granting of relative rights, or the granting of any license. (3) The products described in this material are intended to be used for standard applications or gen- eral electronic equipment (such as office equipment, communications equipment, measuring in- struments and household appliances). Consult our sales staff in advance for information on the following applications:

• Special applications (such as for airplanes, aerospace, automobiles, traffic control equipment, combustion equipment, life support systems and safety devices) in which exceptional quality and reliability are required, or if the failure or malfunction of the products may directly jeopardize life or harm the human body.
• Any applications other than the standard applications intended. (4) The products and product specifications described in this material are subject to change without notice for reasons of modification and/or improvement. At the final stage of your design, purchas- ing, or use of the products, therefore, ask for the most up-to-date Product Standards in advance to make sure that the latest specifications satisfy your requirements. (5) When designing your equipment, comply with the guaranteed values, in particular those of maxi- mum rating, the range of operating power supply voltage and heat radiation characteristics. Other- wise, we will not be liable for any defect which may arise later in your equipment. Even when the products are used within the guaranteed values, redundant design is recommended, so that such equipment may not violate relevant laws or regulations because of the function of our products. (6) When using products for which dry packing is required, observe the conditions (including shelf life and after-unpacking standby time) agreed upon when specification sheets are individually exchanged. (7) No part of this material may be reprinted or reproduced by any means without written permission from our company.

2001 MAR