ALT6713 ANADIGICS | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 10

Technical content

HELP4TM UMTS700 (Bands 13 & 14) LTE Linear PAM Data Sheet - Rev 2.7

10 Pin 3 mm x 3 mm x 1 mm

Figure 1: Block Diagram

FEATURES

  • LTE Compliant
  • 4th Generation HELPTM technology
  • High Efficiency (LTE MPR = 0 dB):
  • 35 % @ P OUT = +27.5 dBm
  • 18 % @ P OUT = +16 dBm
  • 12 % @ P OUT = +6 dBm
  • Low Quiescent Current: 3 mA
  • Low Leakage Current in Shutdown Mode: <5 µA
  • Internal Voltage Regulator
  • Integrated “daisy chainable” directional coupler with CPL IN and CPLOUT port.
  • Optimized for a 50 Ω System
  • 1.8 V Control Logic
  • RoHS Compliant Package, 260 oC MSL-3

APPLICATIONS

  • Band 13 & 14 LTE Wireless Devices PRODUCT DESCRIPTION The ALT6713 HELP4TM PA is a 4th generation HELPTM product for LTE devices operating in UMTS 700 MHz Bands 13 and 14. This PA incorporates ANADIGICS’ HELP4TM technology to deliver exceptional efficiency at low power levels and low quiescent current without the need for external voltage regulators or converters. The device is manufactured using advanced InGaP- Plus TM HBT technology offering state-of-the-art reliability, temperature stability, and ruggedness. Three selectable bias modes that optimize efficiency for different output power levels and a shutdown mode with low leakage current increase handset talk and standby time. A “daisy chainable” directional coupler is integrated in the module, thus eliminating the need of an external coupler. The self-contained 3 mm x 3 mm x 1 mm surface mount package incorporates matching networks optimized for output power, efficiency, and linearity in a 50 Ω system. V BAT T RF IN V MODE 2 V MODE 1 V EN CP L OU T GN D CP L IN RF OU T V CC Bias Contro l Voltage Regulatio n CP L GND at Slug (pad ) ALT6713

Data Sheet - Rev 2.7 ALT6713 Figure 2: Pinout (X-ray Top View) Table 1: Pin Description VBATT RFIN VMODE 2 VMODE 1 VEN CPLOU T GN D CPLIN RFOU T VCC1 PIN NAME DESCRIPTION

1 VBATT Battery Voltage

2 RFIN RF Input

3 VMODE2 Mode Control Voltage 2

4 VMODE1 Mode Control Voltage 1

5 VEN PA Enable Voltage

6 CPLOUT Coupler Output

7 GND Ground

8 CPLIN Coupler Input

9 RFOUT RF Output

10 VCC Supply Voltage

Data Sheet - Rev 2.7 ALT6713

ELECTRICAL CHARACTERISTICS

Table 2: Absolute Minimum and Maximum Ratings Stresses in excess of the absolute ratings may cause permanent damage. Functional operation is not implied under these conditions. Exposure to absolute ratings for extended periods of time may adversely affect reliability. Table 3: Operating Ranges The device may be operated safely over these conditions; however, parametric performance is guaranteed only over the conditions defined in the electrical specifications. Notes: (1) LTE waveform characteristics: 10 MHz QPSK, 12 RB. (2) P OUT derated 0.5 dB for 3.2 V operation. PARAMETER MIN MAX UNIT Supply Voltage (VCC) 0 +5 V Battery Voltage (VBATT) 0 +6 V Control Voltages (VMODE1, VMODE2, VEN) 0 +3.5 V RF Input Power (PIN) - +10 dBm Storage Temperature (TSTG) -40 +150 °C PARAMETER MIN TYP MAX UNIT COMMENTS Operating Frequency (f) 777 - 798 MHz Supply Voltage (VCC) +3.2 +3.4 +4.35 V POUT < +27.5 dBm Enable Voltage (VEN) +1.35 +1.8 +3.1 +0.5 V PA "on" PA "shut down" Mode Control Voltage (VMODE1,VMODE2) +1.35 +1.8 +3.1 +0.5 V Low Bias Mode High Bias Mode Output Power (UMTS) LTE(1) (MPR=0), HPM LTE(1) (MPR=0), MPM LTE(1) (MPR=0), LPM 27(2) 15.5(2) 27.5 dBm TS 36.101 Rel 8 for LTE Case Temperature (TC) -30 - +90 °C

Data Sheet - Rev 2.7 ALT6713 Table 4: Electrical Specifications - LTE Operation (MPR = 0 dB waveform, 10 MHZ QPSK, 12 RB) (TC = +25 °C, VCC = +3.4 V, VBATT = +3.4 V, VEN = +1.8 V, 50 Ω system) Notes: (1) ACLR and Efficiency measured at 787 MHz. PARAMETER MIN TYP MAX UNIT COMMENTS POUT VMODE1 VMODE2 Gain dB +27.5 dBm +16 dBm +6 dBm 0 V 1.8 V 1.8 V 0 V 0 V 1.8 V LTE to LTE, E-UTRA -40 -38 -45 -35 -35 -35 dBc +27.5 dBm +16 dBm +6 dBm 0 V 1.8 V 1.8 V 0 V 0 V 1.8 V UTRA ACLR1 -41 -40 -45 -37 -36 -37 dBc +27.5 dBm +16 dBm +6 dBm 0 V 1.8 V 1.8 V 0 V 0 V 1.8 V UTRA ACLR2 -64 -60 -66 -40 -40 -40 dBc +27.5 dBm +16 dBm +6 dBm 0 V 1.8 V 1.8 V 0 V 0 V 1.8 V Power-Added Efficiency (1) +27.5 dBm +16 dBm +6 dBm 0 V 1.8 V 1.8 V 0 V 0 V 1.8 V Quiescent Current (Icq) Low Bias Mode - 3 4.5 mA through VCC pin 1.8 V 1.8 V Mode Control Current - 0.08 0.15 mA through VMODE pins, VMODE1,2 = +1.8 V Enable Current - 0.1 0.2 mA through VEN pin BATT Current - 0.8 1.5 mA through VBATT pin, VMODE1,2 = +1.8 V Leakage Current - 4 10 µA VBATT = +4.35 V, VCC = +4.35 V, VEN = 0 V, VMODE1,2 = 0 V Noise Power -131 -138 -145 dBm/Hz

746 MHz to 768 MHz

GPS Band, 1574 MHz to 1577 MHz ISM Band, 2400 MHz to 2483.5 MHz Harmonics 2fo 3fo, 4fo -47 -62 - dBc P OUT < +27.5 dBm Coupling Factor - 20 - dB Directivity - 19 - dB Daisy Chain Insertion Loss - <0.35 - dB 698 MHz through 2620 MHz Pin 8 through 9, shutdown mode Spurious Output Level (all spurious outputs) - - -70 dBc POUT < +27.5 dBm In-band load VSWR < 5:1 Out-of-band load VSWR < 10:1 Applies over all operating conditions Load mismatch stress with no permanent degradation or failure 8:1 - - VSWR Applies over full operating range

Data Sheet - Rev 2.7 ALT6713

APPLICATION INFORMATION

To ensure proper performance, refer to all related Application Notes on the ANADIGICS web site: http://www.anadigics.com Shutdown Mode The power amplifier may be placed in a shutdown mode by applying logic low levels (see Operating Ranges table) to the VEN, VMODE1 and VMODE2 voltages. Bias Modes The power amplifier may be placed in either Low, Medium or High Bias modes by applying the Table 5: Bias Control appropriate logic level (see Operating Ranges table) to the VMODE pins. The Bias Control table below lists the recommended modes of operation for various applications. Three operating modes are recommended to optimize current consumption. High Bias/High Power operating mode is for POUT levels > 16 dBm. At ~16 dBm - 6 dBm, the PA could be switched to Medium Power Mode. For POUT levels < ~6 dBm, the PA could be switched to Low Power Mode for extremely low current consumption. APPLICATION POUT LEVELS BIAS MODE VEN VMODE1 VMODE2 VCC VBATT Low power Med power (Medium Bias Mode) > 6 dBm High power (High Bias Mode) > +16 dBm High +1.8 V 0 V 0 V 3.2 - 4.35 V > 3.2 V Shutdown - Shutdown 0 V 0 V 0 V 3.2 - 4.35 V > 3.2 V VEN VCC note 1 RFIN notes 1,2 OFF Sequence Referenced After 90% of Rise Time Referenced Before 10% of Fall Time ON Sequence On Sequence Start T_0N = 0µ T_0N+1µS T_0N+3µS Off Sequence Start T_0FF = 0µ T_0FF+2µST_0FF+3µS Vcontrols Venable/Vmode(s) Rise/Fall Max 1µS Defined at 10% to 90% of Min/Max Voltage Figure 3: Minimum Recommended ON/OFF Timing Sequence Notes: (1) Level may be changed after RF is ON. (2) RF OFF defined as Pin ≤ -30 dBm. (3) Simultaneous switching of V MODE and VEN is not recommended

Data Sheet - Rev 2.7 ALT6713 Figure 4: Evaluation Board Schematic 2.2 µF ceramic RF IN V BATT V MODE1 RF OUTRF IN GND V CC V EN CPL OUT V CC 33 pF V BATT V MODE 1 V EN CPL IN V MODE2 (N/C) 2.2 µF 0.1 µF GND at slug CPL IN 68 pF CPL OUT RF OUT 0.01 µF

Data Sheet - Rev 2.7 ALT6713 PCB AND STENCIL DESIGN GUIDELINEPCB AND STENCIL DESIGN GUIDELINE Figure 7: Recommended PCB Layout Information

ANADIGICS products are not intended for use in life support appliances, devices or systems. Use of an ANADIGICS product in any such application without written consent is prohibited. iMPOrTanT nOTiCE anaDigiCS, inc.

141 Mount Bethel Road

Warren, New Jersey 07059, U.S.A. Tel: +1 (908) 668-5000 Fax: +1 (908) 668-5132 URL: http://www.anadigics.com ANADIGICS, Inc. reserves the right to make changes to its products or to discontinue any product at any time without notice. The product specifications contained in Advanced Product Information sheets and Preliminary Data Sheets are subject to change prior to a product’s formal introduction. Information in Data Sheets have been carefully checked and are assumed to be reliable; however, ANADIGICS assumes no responsibilities for inaccuracies. ANADIGICS strongly urges customers to verify that the information they are using is current before placing orders. Data Sheet - Rev 2.7 ALT6713

ORDERING INFORMATION

DESCRIPTION COMPONENT PACKAGING ALT6713RM45Q7 -30 oC to +90 oC RoHS Compliant 10 Pin 3 mm x 3 mm x 1 mm Surface Mount Module Tape and Reel, 2500 pieces per Reel ALT6713RM45P9 -30 oC to +90 oC RoHS Compliant 10 Pin 3 mm x 3 mm x 1 mm Surface Mount Module Partial Tape and Reel