DATASHEET SEARCH SITE | WWW.ALLDATASHEET.COM

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 7

Technical content

Features

 50 Ω all RF ports  Integrated directional coupler, -17 dB coupling factor, > 14 dB directivity  Integrated power detector  High Tx – Rx switch isolation  3 to 4.2V supply  Small size: 3.2 x 3.2 x 0.6 mm  Stable under all loads or conditions  Gain of 28dB  Meets 802.11a/n emission mask requirements @ 15dBm  Meets FCC 15.205 emission requirements @ 15dBm  EVM < -31.5dB at 15dBm, < -35dB at 12dBm  Idd < 105mA @ 15dBm Pout  PAE(PA) > 20% @Pout (ANT) = 15dBm  Only 1 external component required

Applications

 Portable WiFi applications  WiFi Access points Package Diagram (Bottom View) Attention: Observe precautions for handling electrostatic sensitive devices. ESD Machine Model = 50 V ESD Human Body Model = 200 V Refer to Avago Application Note A004R: Electrostatic Discharge, Damage and Control. GND TX PAEN GND SW1 CPLR RX VBIAS VDD SW0 GND BIAS NETWORK GND ANT GND GND BOTTOM VIEW 0.30 0.30 3.20 3.201.60 1.60 VBIAS PAEN TX GND GND ANT GND VDD SW0 GND GND SW1 CPLR RX

Table 1. Minimum and Maximum Ratings Table 2. Operating Range

Table 3. RF Electrical Characteristics

85 Pout = 12 dBm

14 Pout = 12 dBm

Table 4. Control Logic Truth Table

Table 5. Pin Description:

1 VDD 2 GND

3 VBIAS 4 GND

5 VREF 6 GND

7 PAEN 8 GND

9 SW0 10 GND

11 SW2 12 GND

13 SW1 14 GND

Table 6. Typical Test Conditions:

1 GND

3 PAEN

4 GND

5 VBIAS

6 VDD

7 SW0

Device Orientation & Pin 1 Location In Tape Marking Specifi cation “6” = Device Code “F” = Manufacturing code “WW” = Build of Work Week “YY” = Build of Year “XXXX” = Last 4 Digits of Assembly Lot Number Note: Package marking provides Orientation and Identifi cation USER FEED DIRECTION TOP VIEW END VIEW USER FEED DIRECTION COVER TAPE CARRIER TAPE REEL AVAGO 6FWWYY XXXX AVAGO 6FWWYY XXXX AVAGO 6FWWYY XXXX AVAGO 6FWWYY XXXX Tape Dimensions Ao: 3.60 Bo: 3.60 Ko: 0.95 Pitch: 8.00 Width: 12.00 Notes: 1. Ao & Bo measured at 0.3 mm above base of pocket. 2. 10 pitches cumulative tol. ±0.2 mm. 3. ( ) Reference dimensions only.

Reel Dimensions (13 inch) Detail ‘X’ Recycle Symbol See Detail ‘X’ Embossed Line X2 90.0mm Length Lines 147.0mm away from center point ESD Label (See Below) FRONT BACK Detail ‘Y’ (Slot Hole) FRONT VIEW BACK VIEW Recycle Symbol Embossed ‘M’ 5.0mm Height Slot 10.0±0.5(2x) Slot 5.0±0.5***(1x) Detail ‘Y’ 30.4* Max Ø100.0±0.5 Ø331.5 Max 1.0 4.0 Detail ‘X’ +0.5 2.2±0.5 Ø20.2 (Min) Ø13.1 -0.2 25.4±1.0* 25.65±1.75**

For product information and a complete list of distributors, please go to our web site: www.avagotech.com Avago, Avago Technologies, and the A logo are trademarks of Avago Technologies in the United States and other countries. Data subject to change. Copyright © 2005-2012 Avago Technologies. All rights reserved. AV02-3812EN - September 20, 2012 Refl ow Profi le Recommendations Typical SMT Refl ow Profi le for Maximum Temperature = 260 +0/-5° C Profi le Feature Sn-Pb Solder Pb-Free Solder Average ramp-up rate (TL to TP) 3°C/sec max 3°C/sec max Preheat – Temperature Min (Tsmin) – Temperature Max (Tsmax) – Time (min to max) (ts) 100° C 150° C 60-120 sec 150° C 200° C 60-120 sec Tsmax to TL – Ramp-up Rate 3°C/sec max Time maintained above: – Temperature (TL) – Time (TL) 183° C 60-150 sec 217° C 60-150 sec Peak temperature (Tp) 240 +0/-5° C 260 +0/-5° C Time within 5° C of actual Peak Temperature (tp) 10-30 sec 20-40 sec Ramp-down Rate 6°C/sec max 6°C/sec max Time 25° C to Peak Temperature 6 min max. 8 min max. Time Temperature Tp TL tp tL t 25° C to Peak Ramp-up ts Tsmin Ramp-down Preheat Critical Zone TL to Tp Tsmax

Ordering Information

Part Number No. of Devices Container AFEM-S106-TR1G 3000 13” Reel AFEM-S106-BLKG 100 Antistatic Bag