AE362 RFHIC | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 5

Technical content

(Preliminary) ▪ Tel : 82-31-250-5011 ▪ All specifications may change without notice. ▪ rfsales@rfhic.com ▪ Version 0.3 Product Features Application

  • 50 ~ 6000MHz
  • GaAs E-pHEMT MMIC
  • Higher linearity
  • Low Noise Figure
  • High Max input power
  • SOT-89 SMD Type package
  • Higher productivity
  • Lower manufacturing cost
  • Pb Free / RoHS Standard
  • Cellular, GSM
  • PCS, W-CDMA
  • Wibro, WiMax

Description

AE362 is a drive or pre-drive amplifier designed in a low cost SOT-89 package. This MMIC is based on Gallium Arsenide Enhancement Mode pHEMT which shows low current and high IP3. It is designed as driver devices for infr astructure equipment in the 50~6000MHz Wirele ss technologies such as Cellular, GSM, PCS, W-CDMA, Wibro, WiMax System. The data in this spec sheet is valid only for 50 ohm application. Specifications PARAMETER UNIT MIN TYP MAX Remark Frequency Range MHz 50 ~ 6000 Gain dB 15.5 Input Return Loss dB -13 Output Return Loss dB -12 Output IP3 dBm 29 32 1dB Compression Point dBm 18 21 W-CDMA Power (4FA) dBm 8.5 Noise Figure dB 1.3 1.8 DC Current mA 45 Supply V oltage V 4.5 Absolute Minimum and Maximum Ratings PARAMETER UNIT MIN TYP MAX Device V oltage V +5 +6 Operating Temperature ℃ -40 +85 Storage Temperature ℃ -40 +150 NOTE 1. Test conditions unless otherwise noted. Freq=1900~2200MHz, Vdd=+4.5V , Ta=25 ,℃ 50Ω system 2. OIP3 measured with 2 tones at an output power of +0dBm/tone separated by 1MHz 3. Test Model 1, 64DPCH, 3.84MHz BW, @±5MHz and ±10MHz offset Package : SOT-89

(Preliminary) ▪ Tel : 82-31-250-5011 ▪ All specifications may change without notice. ▪ rfsales@rfhic.com ▪ Version 0.3 -20 -10 -30 Freq(GHz) Gain(dB) S-parameter ◎ Application Circuit: 800MHz ~ 900MHz, 50ohm System ◎ Typical RF Performance: VDD=4.5V , IDS=45mA, TA=25℃, 50ohm System Noise Figure vs Frequency 0.0 0.5 1.0 1.5 2.0 2.5 3.0 800 820 840 860 880 900 Freq(MHz) OIP3 vs Frequency 26.0 28.0 30.0 32.0 34.0 36.0 800 820 840 860 880 900 Freq(MHz) P1dB vs Frequency 14.0 16.0 18.0 20.0 22.0 24.0 800 820 840 860 880 900 Freq(MHz) S21 S11 S22

(Preliminary) ▪ Tel : 82-31-250-5011 ▪ All specifications may change without notice. ▪ rfsales@rfhic.com ▪ Version 0.3 ◎ Application Circuit: 1900MHz ~ 2200MHz, 50ohm System ◎ Typical RF Performance: VDD=4.5V , IDS=45mA, TA=25℃, 50ohm System Noise Figure vs Frequency 0.00 0.50 1.00 1.50 2.00 2.50 3.00 1900 1940 1980 2020 2060 2100 2140 2180 Freq(MHz) -20 -10 -30 freq, GHz S-parameter S21 S11 S22 OIP3 vs Frequency 26.0 28.0 30.0 32.0 34.0 36.0 1900 1940 1980 2020 2060 2100 2140 2180 Freq(MHz) P1dB vs Frequency 14.0 16.0 18.0 20.0 22.0 24.0 1900 1940 1980 2020 2060 2100 2140 2180 Freq(MHz)

(Preliminary) ▪ Tel : 82-31-250-5011 ▪ All specifications may change without notice. ▪ rfsales@rfhic.com ▪ Version 0.3 ◎ Application Circuit: 2400MHz ~ 2600MHz, 50ohm System ◎ Typical RF Performance: VDD=4.5V , IDS=45mA, TA=25℃, 50ohm System -20 -10 -30 freq, GHz S - parameter S21 S11 S22 Noise Figure vs Frequency 0.0 0.5 1.0 1.5 2.0 2.5 3.0 2400 2440 2480 2520 2560 2600 Freq(MHz) OIP3 vs Frequency 26.0 28.0 30.0 32.0 34.0 36.0 2400 2440 2480 2520 2560 2600 Freq(MHz) P1dB vs Frequency 14.0 16.0 18.0 20.0 22.0 24.0 2400 2440 2480 2520 2560 2600 Freq(MHz)

(Preliminary) ▪ Tel : 82-31-250-5011 ▪ All specifications may change without notice. ▪ rfsales@rfhic.com ▪ Version 0.3 For a safe use in all situations, it is recommended to ha ve proper ESD control techniques while the device is being handled. Here are some recommended precautions; - Person at a workbench should be earthed via a wrist strap and a resistor. - All mains-powered equipment should be connected to the mains via an earth-leakage switch. - Equipment cases should be grounded. - Relative humidity should be maintained between 40% and 50%. - An ionizer is recommended. - Keep static materials, such as plastic envelopes and plastic trays etc. away from the workbench PCB Pad Layout Recommended Mounting Configuration ESD Protection Dimensions Pin No Function

1 Input

2 Ground

3 Output/Bias

4 Ground

Mounting Configuration Notes 1.Ground / thermal via holes are critical for the proper performance of this device. 2. Add as much copper as possible to inner and outer layers near the part to ensure optimal thermal performance. 3. Mounting screws can be added near the part to fasten the board to a heatsink. Ensure that the ground / thermal via hole regi on contacts the heatsink. 4. Do not put solder mask on the backside of the PCB in the region where the board contacts the heatsink. 5. RF trace width depends upon the PCB material and construction. 6. Use 1 oz. Copper minimum. 7. All dimensions are in millimeters. RFHIC Corporation (RFHIC) reserves the right to make changes to any products herein or to discontinue any product at any time w ithout notice. RFHIC do not assume any liability for the suitability of its products for any particular purpose, and disclaims any and all liability, inclu ding without limitation consequential or incidental damages. The product specifications herein expressed ha ve been carefully checked and are assumed to be reliable. How ever, RFHIC disclaims liability for inaccuracies and strongly recommends buyers to verify that the information they are using is current before placing purchase orders. RFHIC products are not intended for use in life support equipment or application where malfunction of the product can be expected to result in personal injury or death. Buyer uses or sells such products for any such unintended or unauthorized application, buyer shall indemnify, protect and hold RFHIC and its directors, officers, stockholders, employees, representatives and distributors harmless ag ainst any and all claims arising out of such use. RFHIC’s liability under or arisin g out of damages, claims of whatsoever kind and nature which RFHIC products could cause shall be limited in amount to the net purchase price of the products sold to buyer by RFHIC.