AD6C332 SOLIDSTATE | Alldatasheet
Document overview
- Manufacturer or author: Provided By alldatasheet.com(free datasheet download site)
- PDF pages: 5
Technical content
1 Form B
The AD6C332 is a bi-directional, single-pole, single-throw, normally closed multipurpose solid-state relay. It is designed to replace electromechanical relays in general purpose switching applications. The relay consists of an integrated circuit that drives two rugged source-to-source depletion type DMOS transistors - optically coupled to a light emitting diode. The output MOS transistors are protected with free-wheeling diodes that can handle up to 5A of inrush current, making the relay ideal for switching lamps and highly inductive loads.
DESCRIPTION
OPTIONS/SUFFIXES* SCHEMATIC DIAGRAM ABSOLUTE MAXIMUM RATINGS* APPROVALS Low On-resistance (10 Ohms MAX)• Low input control power consumption (2.5mA TYP)• 200mA maximum continuous load current• High input-to-output isolation• Long life/high reliability• Reed relay replacement• Meter reading systems• Medical equipment• Battery monitoring• Multiplexers• Surface Mount Leadform Option• -S Tape and Reel Option• -TR NOTE: Suffixes listed above are not included in marking on device for part number identification. PARAMETER UNIT MIN TYP MAX Storage Temperature °C -55 125 Operating Temperature °C -40 85 Continuous Input Current mA 40 Transient Input Current mA 400 Reverse Input Control Voltage V 6 Output Power Dissipation mW 800 *The values indicated are absolute stress ratings. Functional operation of the device is not implied at these or any conditions in excess of those defined in electrical characteristics section of this document. Exposure to Absolute Ratings may cause permanent damage to the device and may adversely affect reliability. BABT CERTIFICATE #607836 BS EN 60950, BS EN 41003, BS EN 60065 CSA CERTIFICATE #LR111581-1• © 2004 Solid State Optronics • San José, CA Page 1 of 5 AD6C332 rev 1.40 (10/25/2004)
ELECTRICAL CHARACTERISTICS - 25°C PARAMETER UNIT MIN TYP MAX TEST CONDITIONS INPUT SPECIFICATIONS LED Forward Voltage V 1.2 1.5 If = 5mA LED Reverse Voltage V 61 2 Ir = 10uA Turn-On Current m 0.5 Io = 200mAA Turn-Off Current m 2.5 5A OUTPUT SPECIFICATIONS Blocking Voltage V 250 Io = 1uA Continuous Load Current m 200 If = 0mAA On-Resistance Ω 8 10 Io = 200mA Leakage Current µ 0.2 1 Vo = 250VA Output Capacitance p 25 Vo = 25V, f = 1.0MHzF Offset Voltage m 0.2 If = 0mAV COUPLED SPECIFICATIONS Isolation Voltage V 2500 T = 1 minute -H Suffix V 3750 T = 1 minute Turn-On Time m 0.8 2 If = 0mA, Io = 200mAs Turn-Off Time m 1 5 If = 5mA, Io = 200mAs Isolation Resistance G 100Ω Coupled Capacitance p 3F Contact Transient Ratio V 2000 7000 dV = 50V/ µ s © 2004 Solid State Optronics • San José, CA Page 2 of 5 AD6C332 rev 1.40 (10/25/2004)
Turn-Off Time (ms) Device Count AD6C332 Typical Turn-Off Time Distribution N = 100, Ambient Temperature = 25°C 6.5 7 7.5 8 8.5 9 9.5 10 O n-R esistance (ohms) Device Count AD6C332 Leakage Current (uA) Device Count Typical On-Resistance Distribution N = 100, Ambient Temperature = 25°C AD6C332 Typical Leakage Current Distribution N = 100, Ambient Temperature = 25°C 250 255 260 265 270 275 280 285 Blocking Voltage (V) Device Count AD6C332 100 150 200 250 -40 -20 0 20 40 60 80 Temperature (C) Load Current (mA) Typical Blocking Voltage Distribution N = 100, Ambient Temperature = 25°C AD6C332 Maximum Load Current vs. Temperature Turn-On Time (ms) Device Count AD6C332 Typical Turn-On Time Distribution N = 100, Ambient Temperature = 25°C © 2004 Solid State Optronics • San José, CA Page 3 of 5 AD6C332 rev 1.40 (10/25/2004)
6 PIN DUAL IN-LINE PACKAGE 6 PIN SURFACE MOUNT DEVICE
© 2004 Solid State Optronics • San José, CA Page 4 of 5 AD6C332 rev 1.40 (10/25/2004)
Solid State Optronics (SSO) makes no warranties or representations with regards to the completeness and accuracy of this document. SSO reserves the right to make changes to product description, specifications at any time without further notice. SSO shall not assume any liability arising out of the applicat ion or use of any product or circuit described herein. Neither ci rcuit patent licenses nor indemnity are expressed or implied. Except as specified in SSO's Standard Terms & Conditions, SSO disclaims liability for consequential or other damage, and we mak e no other warranty, expressed or implied, including merchantability and fitness for particular use. DISCLAIMER LIFE SUPPORT POLICY SSO does not authorize use of its devices in life support applications wherein failure or malfunction of a device may lead to personal injury or death. Users of SSO devices in life support applications assume all risks of su ch use and agree to indemnify SSO against any an d all damages resulting from such use. Life support devices are def ined as devices or systems which, (a) are intended for surgical im plant into the body, or (b) support or sustain life, and (c) whose failure to perf orm when used properly in accordance with instructions for u se can be reasonably expected to result in significant injury to the user, or (d) a critical component in any component of a life support device or system whose failure can be reasonably expected to c ause failure of the life support device or system, or to affect its safety or effe ctiveness. © 2004 Solid State Optronics • San José, CA Page 5 of 5 AD6C332 rev 1.40 (10/25/2004)