AD274 RFHIC | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 6

Technical content

Korean Facilities : 82-31-250-5078 / rfsales@rfhic.com All specifications may change without notice US Facility : 919-677-8780 / sales@rfhicusa.com 1 / 6 Version 1.0 Product Features Applications

  • 2-Way Splitter
  • 30MHz-1200MHz
  • Small size (3X3 mm)
  • QFN SMD Type package
  • Higher productivity
  • Lower manufacturing cost
  • -57dBc CSO 135 Channels @ +15dBmV/ch
  • -62dBc CTB 135 Channels @ +15dBmV/ch
  • -66dBc XMD 135 Channels @ +15dBmV/ch
  • 3.5dB Typical Noise Figure
  • 75ohm input and outputs
  • Multi Tuner Set-Top Boxes
  • Home Gateways
  • FTTx (G-PON, GE-PON)

Description

AD274 is designed as low cost Active Divider for many applications including FTTH, CATV System. This MMIC is based on Gallium Arsenide Enhancement Mode pHEMT which shows low current draw and very low noise. The data in this spec sheet is valid only for 75ohm application. Electrical Specifications PARAMETER UNIT MIN TYP MAX Typ Frequency MHz 30 ~ 1000 - Gain dB 4.5 5.5 - 4 Gain Flatness dB 1.4 2 1.6 Input Return Loss dB - -16 - -12 Output Return Loss dB - -20 - -20 IN&OUT Port Isolation dB - -30 - -30 OUT&OUT Port Isolation dB - -20 - -20 Output IP3 dBm 22 26 - 18 1dB Compression Point dBm 8 12 - 8 Noise Figure dB - 3.5 4.5 3.3 CSO 50 ~ 870MHz 135 channel@ Input Power +15dBmV/ch dBc - -57 - -51 CTB dBc - -62 - -58 XMOD dBc - -66 - -56 DC Current mA - 110 - 75 Supply Voltage V 5 3.3 Note 1. Test conditions unless otherwise noted. Test Freq = 500MHz, T=25℃, Vdd=5V , 75Ω system 2. OIP3 measured with 2 tones at an output power of +0dBm/tone separated by 1MHz, Test Freq = 500MHz Absolute Maximum Ratings PARAMETER UNIT MIN TYP MAX Device Voltage VDC - 5 5.5 Operating Case Temperature ℃ -40 - 85 Storage Temperature ℃ -40 - 150 ESD Human Body Model - - Class 1A - Moisture sensitivity Level - - MSL1 - Junction temperature ℃ - 120 180 Thermal Resistance (Rth) ℃/W - 70 - Package Type : QFN 3X3

Korean Facilities : 82-31-250-5078 / rfsales@rfhic.com All specifications may change without notice US Facility : 919-677-8780 / sales@rfhicusa.com 2 / 6 Version 1.0 Application Circuit @ 50 ~ 1000MHz, Vdd = +5V , 75ohm System S-Parameter Isolation Noise Figure

Korean Facilities : 82-31-250-5078 / rfsales@rfhic.com All specifications may change without notice US Facility : 919-677-8780 / sales@rfhicusa.com 3 / 6 Version 1.0 Application Circuit @ 50 ~ 1000MHz, +3.3V , 75ohm System S-Parameter Isolation Noise Figure

Korean Facilities : 82-31-250-5078 / rfsales@rfhic.com All specifications may change without notice US Facility : 919-677-8780 / sales@rfhicusa.com 4 / 6 Version 1.0 Multi-Tone Test : 135CH_FLAT@Input Power +15dBmV/Ch, Sdd=+5V Level : Input +15dBmV Tilt : 135CH FRQ XMOD CTB RAW CTB COR N-FLR CSU RAW CSU COR CSU FRQ CSL RAW CSL COR CSL FRQ Multi-Tone Test : 135CH_FLAT@Input Power +15dBmV/Ch, Vdd = +3.3V Level : Input +15dBmV Tilt : 135CH_FLAT FRQ XMOD CTB RAW CTB COR N-FLR CSU RAW CSU COR CSU FRQ CSL RAW CSL COR CSL FRQ

Korean Facilities : 82-31-250-5078 / rfsales@rfhic.com All specifications may change without notice US Facility : 919-677-8780 / sales@rfhicusa.com 5 / 6 Version 1.0 * U n i t : m m [ i n c h ] | T o l e r a n c e : ±0.2[.008] ▲ T o p V i e w ▲ S i d e V i e w ▲ Bottom View Pin Description Pin No Function Pin No Function Pin No Function Pin No Function

1 NC 5 Bias/Port1 9 Output-1 13 NC

2 GND 6 NC 10 GND 14 NC

3 GND 7 Port2 11 GND 15 NC

4 Input 8 NC 12 Output-2 16 NC

  • Mounting Configuration Notes 1. Ground / thermal via holes are critical for the proper performance of this device. 2. Add as much copper as possible to inner and outer layers near the part to ensure optimal thermal performance. 3. Mounting screws can be added near the part to fasten the board to a heatsink. Ensure that the ground / thermal via hole region contacts the heatsink. 4. Do not put solder mask on the backside of the PCB in the region where the board contacts the heatsink. 5. RF trace width depends upon the PCB material and construction. 6. Use 1 oz. Copper minimum.

Korean Facilities : 82-31-250-5078 / rfsales@rfhic.com All specifications may change without notice US Facility : 919-677-8780 / sales@rfhicusa.com 6 / 6 Version 1.0

Revision History

Part Number Release Date Version Modification Data Sheet Status AD274 2013.02.20 1.0 - - AD274 2013.01.08 0.2 Change by a new dimension form Preliminary AD274 2012.09.10 0.1 Change by a new document form Preliminary RFHIC Corporation reserves the right to make changes to any products herein or to discontinue any product at any time without notice. While product specifications have been thoroughly examined for reliability, RFHIC Corporation strongly recommends buyers to verify that the information they are using is accurate before ordering. RFHIC Corporation does not assume any liability for the suitability of its products for any particular purpose, and disclaims any and all liability, including wi thout limitation consequential or incidental damages. RFHIC products are not intended for use in life support equipment or application where malfunction of the product can be expected to result in personal injury or death. Buyer uses or sells such products for any such unintended or unauthorized application, buyer shall indemnify, protect and hold RFHIC Corporation and its directors, officers, stockholders, employees, representatives and distributors harmless against any and all claims arising out of such unauthorized use. Sales, inquiries and support should be directed to the local authorized geographic distributor for RFHIC Corporation. For customers in the US, please contact the US Sales Team at 919- 677-8780. For all other inquiries, please contact the International Sales Team at 82-31-250-5078.