DATASHEET SEARCH SITE | WWW.ALLDATASHEET.COM
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 8
Technical content
Aeroflex’s ACT8512 is a radia tion tolerant, 48 channel multiple xer MCM (multi-chip module) with electrostatic discharge (ESD) protection on all channel inputs. The ACT8512 has been specifically designed to meet exposure to radiation environments. The multiplexer is available in a 96 lead High Temperature Co-F ired Ceramic (HTCC) Quad Flatpack (CQFP). It is guaranteed operational from -55°C to +125°C. Available screened in accordance with MIL-PRF-38534, the ACT8512 is ideal for demanding military and space applications. ORGANIZATION AND APPLICATION The ACT8512 consists of six 16 channel multiplexers arranged as shown in the Block Diagram. The ACT8512 design is inherently radiation tolerant. The ACT8512 consists of forty-eight (48) channels addressable by bus A 0~A3 in three 16 channel blocks, each block enabled separately. Each block connects th e addressed channel to two outputs, "Output" and "Current". This technique enable s selecting and reading a remote resistive sensor without the MUX resistance being part of the measurement. For grounded sensors, this is done by passing current to the sensor by means of the "Current" pin and reading the resultant voltage (proportional to the sensor resistance) at the "Output" pin. ACT8512 48-Channel Analog Multiplexer Module Radiation Tolerant & ESD Protected
FEATURES
❑ 48 channels provided by six 16-channel multiplexers ❑ Radiation performance - Total dose: 150 krads(Si), Dose rate = 50 - 300 rads(Si)/s - SEU: Immune up to 90 MeV-cm 2/mg - SEL: Immune by process design ❑ Full military temperature range ❑ Low power consumption < 90mW ❑ One address bus (A0-3) and three enable lines afford flexible organization ❑ All channel inputs protected by ±20V nominal transorbs ❑ Fast access time < 500ns typical ❑ Break-Before-Make switching ❑ High analog input impedance (power on or off) ❑ Designed for aerospace and high reliability space applications ❑ Packaging – Hermetic ceramic - 96 leads, 1.32"Sq x 0.20"Ht quad flat pack - Typical Weight 15 grams ❑ DSCC 5962-09203 SMD pending www.aeroflex.com/mux Standard Products November 14, 2008 Note: Aeroflex Plainview does not currently have a DSCC certified Radiation Hardened Assurance Program.
SCD8512 Rev D 11/14/08 Aeroflex Plainview ACT8512 48 – CHANNEL ANALOG MUX BLOCK DIAGRAM CH 0 CH 15 EN 0-15 CH 16 CH 31 EN 16-31 CURRENT 16-31 OUTPUT 32-47 CURRENT 32-47 OUTPUT 16-31 CURRENT 0-15 CH 32 CH 47 EN 32-47 MUX 3 MUX 5 MUX 6 MUX 4 1616 VR VR VR +VEE -VEE VREF GND OUTPUT 0-15 MUX 2MUX 1
SCD8512 Rev D 11/14/08 Aeroflex Plainview ABSOLUTE MAXIMUM RATINGS 1/ Parameter Range Units Case Operating Temperature Range -55 to +125 °C Storage Temperature Range -65 to +150 °C Supply Voltage EE (Pin 44) -VEE (Pin 46) VREF (Pin 48) +20 -20 +7.5 V V V Digital Input Overvoltage V EN (Pins 5, 91, 92), VA (Pins 1, 3, 93, 95) <VREF +0.5 >GND -0.5 V V Analog Input Over Voltage VS ±18V V Notes: 1/ All measurements are made with respect to ground. NOTICE: Stresses above those listed under "Absolute Maximums Rating" may cause permanent damage to the device. These are stress rating only; functional operation beyond the "Operation Conditions" is not recommended and extended exposure beyond the "Operation Conditions" may affect device reliability. RECOMMENDED OPERATING CONDITIONS 1/ Symbol Parameter Typical Units +VEE +15V Power Supply Voltage +15.0 V -VEE -15V Power Supply Voltage -15.0 V VREF Reference Voltage +5.00 V VAL Logic Low Level +0.8 V VAH Logic High Level +4.0 V Notes: 1/ Power Supply turn-on sequence shall be as follows: -VEE, VREF, followed by +VEE. DC ELECTRICAL PERFORMANCE CHARACTERISTICS 1/ (Tc = -55°C to +125°C, -VEE = -15V, VREF = +5.0V, +VEE = +15V - Unless otherwise specified) Parameter Symbol Conditions Min Max Units Supply Current +I EE VEN(0-47) = VA(0-3) = 0 0 3 mA -IEE -3 0 mA +ISBY V EN(0-47) = 4V, VA(0-3) = 0 7/0 3 m A -ISBY -3 0 mA Address Input Current I AL(0-3) V A = 0V -6 6 μA IAH(0-3) V A = 5V -6 6 μA Enable Input Current I ENL(0-15) V EN(0-15) = 0V -2 2 μA IENH(0-15) V EN(0-15) = 5V -2 2 μA IENL(16-31) V EN(16-31) = 0V -2 2 μA IENH(16-31) V EN(16-31) = 5V -2 2 μA IENL(32-47) V EN(32-47) = 0V -2 2 μA IENH(32-47) V EN(32-47) = 5V -2 2 μA
SCD8512 Rev D 11/14/08 Aeroflex Plainview Positive Input Leakage Current CH0-CH47 ISOFFOUTPUT VIN = +10V, VEN = 4V, output and all unused MUX inputs under test = -10V 2/ 3/ -100 +1000 nA +ISOFFCURRENT -100 +1000 nA Negative Input Leakage Current CH0-CH47 -ISOFFOUTPUT VIN = -10V, VEN = 4V, output and all unused MUX inputs under test = +10V 2/, 3/ -100 +1000 nA -ISOFFCURRENT -100 +1000 nA Output Leakage Current OUTPUTS (pins 25, 70 & 68) CURRENTS (pins 67 & 69) DOFFOUTPUT VOUT = +10V, VEN = 4V, output and all unused MUX inputs under test = -10V 3/, 4/ -100 +100 nA +IDOFFCURRENT -100 +100 nA Output Leakage Current OUTPUTS (pins 25, 70 & 68) CURRENTS (pins 67 & 69) DOFFOUTPUT VOUT = -10V, VEN = 4V, output and all unused MUX inputs under test = +10V 3/, 4/ -100 +100 nA -IDOFFCURRENT -100 +100 nA Input Clamped Voltage CH0 - CH47 +VCLMP VEN = 4V, all unused MUX inputs under test are open. 3/ +25°C +125°C -55°C 18.0 18.0 17.5 23.0 23.5 22.5 V V V Input Clamped Voltage CH0 - CH47 CLMP +25°C +125°C -55°C -23.0 -23.5 -22.5 -18.0 -18.0 -17.5 V V V Switch ON Resistance OUTPUTS (pins 25, 70 & 68) RDS(ON)(0-47)A VIN = +15V, VEN = 0.8V, IOUT = -1mA 2/, 3/, 5/ 200 1000 Ω RDS(ON)(0-47)B VIN = +5V, VEN = 0.8V, IOUT = -1mA 2/, 3/, 5/ 200 1500 Ω RDS(ON)(0-47)C VIN = -5V, VEN = 0.8V, IOUT = +1mA 2/, 3/, 5/ 200 2500 Ω Switch ON Resistance CURRENTS (pins 26, 67 & 69) RDS(ON)(0-47)A VIN = +15V, VEN = 0.8V, IOUT = -1mA 2/, 3/, 5/ 200 1000 Ω RDS(ON)(0-47)B VIN = +5V, VEN = 0.8V, IOUT = -1mA 2/, 3/, 5/ 200 1500 Ω RDS(ON)(0-47)C VIN = -5V, VEN = 0.8V, IOUT = +1mA 2/, 3/, 5/ 200 2500 Ω Notes: 1/ Measure inputs sequentially. Ground all unused inputs of the device under test. VA is the applied input voltage to the address lines A(0-3). 2/ VIN is the applied input voltage to the input channels CH0-CH47. 3/ VEN is the applied input voltage to the enable lines En(0-15), En(16-31) and En(32-47). 4/ VOUT is the applied input voltage to the output lines OUTPUT(0-15), OUTPUT(16-31), OUTPUT(32-47), CURRENT(0-15) , CURRENT(16-31) and CURRENT(32-47). 5/ Negative current is the current flowing out of each of the MUX pins. Positive current is the current flowing into each MUX pin. 6/ The ACT8512 cannot be operated with analog inputs from -15 to -5 volts. 7/ Not tested, guaranteed to the specified limits. SWITCHING CHARACTERISTICS (Tc = -55°C to +125°C, -VEE = -15V, VREF = +5.0V, +VEE = +15V -- Unless otherwise specified) Parameter Symbol Conditions Min Max Units Switching Test MUX tAHL RL = 10KΩ, CL = 50pF 10 1000 ns tALH 10 1000 ns tONEN RL = 1KΩ, CL = 50pF 10 1000 ns tOFFEN 10 1000 ns DC ELECTRICAL PERFORMANCE CHARACTERISTICS 1/ (continued) (Tc = -55°C to +125°C, -VEE = -15V, VREF = +5.0V, +VEE = +15V - Unless otherwise specified) Parameter Symbol Conditions Min Max Units
SCD8512 Rev D 11/14/08 Aeroflex Plainview TRUTH TABLE (CH0 – CH15) A3 A2 A1 A0 EN(0-15) "ON" CHANNEL 1 / XXXX H N O N E LLLL L C H 0 LLLH L C H 1 LLHL L C H 2 LLH H L C H 3 LHLL L C H 4 LHLH L C H 5 LHHL L C H 6 LHHH L C H 7 HLLL L C H 8 HLLH L C H 9 HLHL L C H 1 0 HLHH L C H 1 1 H H L L L CH12 H H L H L CH13 HHHL L C H 1 4 HHHH L C H 1 5 1/ Between CH0-15 and OUTPUT (0-15) and CURRENT (0-15). TRUTH TABLE (CH16 – CH31) A3 A2 A1 A0 EN(16-31) "ON" CHANNEL 1 / XXXX H N O N E LLLL L C H 1 6 LLLH L C H 1 7 L L H L L CH18 L L H H L CH19 L H L L L CH20 LHLH L C H 2 1 L H H L L CH22 LHHH L C H 2 3 HLLL L C H 2 4 H L L H L CH25 HLHL L C H 2 6 H L H H L CH27 H H L L L CH28 H H L H L CH29 HHHL L C H 3 0 HHHH L C H 3 1 1/ Between CH16-31 and OUTPUT (16-31) and CURRENT (16-31). TRUTH TABLE (CH32 – CH47) A3 A2 A1 A0 EN(32-47) "ON" CHANNEL 1 / XXXX H N O N E LLLL L C H 3 2 LLLH L C H 3 3 L L H L L CH34 L L H H L CH35 L H L L L CH36 LHLH L C H 3 7 L H H L L CH38 LHHH L C H 3 9 HLLL L C H 4 0 H L L H L CH41 HLHL L C H 4 2 H L H H L CH43 H H L L L CH44 H H L H L CH45 HHHL L C H 4 6 HHHH L C H 4 7 1/ Between CH32-47 and OUTPUT (32-47) and CURRENT (32-47)
SCD8512 Rev D 11/14/08 Aeroflex Plainview ACT8512 SWITCHING DIAGRAMS 4.0V 50% ~3V to 12.5V 50% tOFFENtONEN Definition of tONEN and tOFFEN 0.8V 50% 50% 4.0V 0.8V 50% 11.6V MIN 11.6V MIN 4.0VAddress Lines tAHL 50% NOTE: f = 10KHz, Duty cycle = 50%. (A0 - A3) MUX Output MUX Output MUX Output Address Lines (A0 - A3) EN Lines tALH Definition of tAHL Definition of tALH 0.8V
SCD8512 Rev D 11/14/08 Aeroflex Plainview PIN NUMBERS & FUNCTIONS ACT8512 – 96 Leads Ceramic QUAD Flat Pack Pin # Function Pin # Function Pin # Function
1 A2 33 CH11 65 CH33
2 NC 34 GND 66 CH32
3 A3 35 CH12 67 Output I(32-47)
4 NC 36 GND 68 Output V(32-47)
5 EN 0-15 37 CH13 69 Output I(16-31)
6 NC 38 GND 70 Output V(16-31)
7 CH0 39 CH14 71 GND
8 GND 40 GND 72 GND
9 CH1 41 CH15 73 CH31
10 GND 42 GND 74 CH30
11 CH2 43 NC 75 CH29
12 GND 44 +VEE 76 CH28
13 CH3 45 NC 77 CH27
14 GND 46 -VEE 78 CH26
15 CH4 47 NC 79 CH25
16 GND 48 VREF 80 CH24
17 CH5 49 NC 81 CH23
18 GND 50 CASE GND 82 CH22
19 CH6 51 CH47 83 CH21
20 GND 52 CH46 84 CH20
21 CH7 53 CH45 85 CH19
22 GND 54 CH44 86 CH18
23 GND 55 CH43 87 CH17
24 GND 56 CH42 88 CH16
25 Output V(0-15) 57 CH41 89 GND
26 Output I(0-15) 58 CH40 90 GND
27 CH8 59 CH39 91 EN 32-47
28 GND 60 CH38 92 EN 16-31
29 CH9 61 CH37 93 A0
30 GND 62 CH36 94 NC
31 CH10 63 CH35 95 A1
32 GND 64 CH34 96 NC
NOTE: It is recommended that all "NC" or "no connect pin" be grounded. This eliminates or minimizes any ESD or static buildup.
PLAINVIEW, NEW YORK Toll Free: 800-THE-1553 Fax: 516-694-6715 SE AND MID-ATLANTIC Tel: 321-951-4164 Fax: 321-951-4254 INTERNATIONAL Tel: 805-778-9229 Fax: 805-778-1980 WEST COAST Tel: 949-362-2260 Fax: 949-362-2266 NORTHEAST Tel: 603-888-3975 Fax: 603-888-4585 CENTRAL Tel: 719-594-8017 Fax: 719-594-8468 www.aeroflex.com info-ams@aeroflex.com Aeroflex Microelectronic Solutions reserves the right to change at any time without notice the specifications, design, function, or form of its products described herein. All parameters must be validated for each customer's application by engineering. No liability is assumed as a result of use of this product. No patent licenses are implied. Our passion for performance is defined by three attributes represented by these three icons: solution-minded, performance-driven and customer-focused EXPORT CONTROL: EXPORT WARNING: This product is controlled for expor t under the International Traffic in Arms Regulations (ITAR). A license from the U.S. Department of State is required prior to the export of this product from the United States. Aeroflex’s military and space products are controlled for export under the International Traffic in Arms Regulations (ITAR) and may not be sold or proposed or offered for sale to certain countries. (See ITAR 126.1 for complete information.) 1.320 SQ Pin 85Pin 12 Pin 60Pin 37 Pin 13 Pin 36 Pin 61 Pin 84 Pin 1 FLAT PACKAGE OUTLINE MAX (23 Spaces at .050) Tol Non-Cum
4 Sides
.0165 ±.003 1.150 ±.005 .200 MAX (.400) Note: Outside ceramic tie bars not shown for clarity. Contact factory for details. .006 ±.001
ORDERING INFORMATION
Model Number Screening DSCC SMD # Package ACT8512-S Military Temperature, -55°C to +125°C, Screened in accordance with MIL-PRF-38534, Class K NA QUAD Flat Pack ACT8512-7 Commercial Fl ow, +25°C testing only ACT8512-201-1S In accordance with DSCC SMD 5962-0920301KXC