ACT11013

74AC11013 PHILIPS | Alldatasheet

Document overview

• Manufacturer or author: Provided By www.digicamel.com(FREE DATASHEET DOWNLOAD SITE)
• PDF pages: 5

Technical content

Philips Components—Signetics AC1 1 01 3: Product Specification ECN No. 00730 October 17, 1980 ACT11013: Objective Specification Dual 4-input NAND Schmitt-trigger ACL Products FEATURES QUICK REFERENCE DATA _ + Output capability: +24 mA CONDITIONS TYPICAL SYMBOL} PARAMETER Tam = 25°C; GND = 0V; UNIT + CMOS (AC) and TTL (ACT) voltage Veo = 50V ac level inputs + 509 incident wave switching teu | Propagation delay Cy = 50pF 43 ns tou | A.B, C,DtoY + Center-pin Veg and ground configu- Power dissipati —— ration to minimize high-speed switch- capacitance-per gate | = *MHziC.=S0pF =| 29 pF in apa 1 eee: $81 Input capacitance | Viz OV or Veo = + Ioc category: Per Jedec JC40.2 / DESCRIPTION : — The 74AC/ACT11013 high-performance Note: _ . a a CMOS devices combine very high 1. Opp is used to determine the dynamic power dissipation (P,, in »W) speed and high output drive compa- Py = Spy x Veg xf, + Z (CL x Veg" x fo) where: rable to the most advanced TTL fami- {| = input frequency in MHz, C, = output load capacitance in pF, lies. fo = output frequency in MHz, Vg = supply voltage in V, (Cx Veg? x fo) = The 74AC/ACT1 1013 provides two Z(G, Veg" fo) = sum of outputs separate 4-input NAND gate functions which are capable of transforming ORDERING INFORMATION — slowly changing input signals into PACKAGES TEMPERATURE RANGE ORDER CODE sharply defined, jitter-free output sig- 14-pin plastic DIP 7 oy 74AC11013N nals. In addition, they have greater (00mil-wide) ~A40°C to +85°C 74ACT11013N noise margin than conventional NAND ta-pin ola _ -pin plastic SO 5 7 74AC11013D gates. (150mil-wide) ; ~A0°C to +85°C 74ACT110130 PIN CONFIGURATION __ LOGIC SYMBOL LOGIC SYMBOL (IEEE/IEC) Nand D Packages | 218 2 18 (4} 14) NC 118 47 1 — 1A [2] 13) 1¢ 13°10 3 13 vo fia} 10 21D | 12 no [4] 171] Vee 30 2A 10 i VG [70] 24 9 2B Pa ° |

20 Ca [ 3) 28 7 2 5 Ps |

2c [a ne 6 20 2 ' | ee a ee

Philips Components—Signetics ACL Products AC11013: Product Specification, ACT 11013: Objective Specification Dual 4-input NAND Schmitt-trigger 74AC/ACT11013 PIN DESCRIPTION _ FUNCTION TABLE PINNUMBER | SYMBOL | NAME AND FUNCTION _ INPUTS OUTPUT ; 19 | 18-28 } Data inputs Hj} H | HHL L 1¢-2C | Data inputs Li x}|x]x H 88 |e | Datsuns KL x 4 [a | eno | Grong (ov) ixix]xie H in Positive supply voltage | RECOMMENDED OPERATING CONDITIONS syBoL PARAMETER 74AC11013 74ACT11013 Unt NOTE: 1. No electrical or switching characteristics are specified at Voc < 3V. Operation between 2V and 3V is not recommended, but within that range, a device output will maintain a previously established logic state. ABSOLUTE MAXIMUM RATINGS! SYMBOL PARAMETER TEST CONDITIONS RATING UNIT : ee hk DC input diode current mA a v ; . oe ox f mA or | De ovedeinenen J MorVoo Tm Vv DC output source or Vo ud, [te | sink current per output pin = Oe Nec #50 mA or mA Low _| OC groundeuren ee ono ground curren Storage temperature “65 to 150 °c Power dissipation per package Above 70°C; derate linearly by &mW/K mW Prot Power dissipation per package i Plastic surface mount (SO) Above 70°C; derate linearly by @mW/K mW | NOTES: 1. Stresses beyond those listed may cause permanent damage to the device. These are stress ratings only and functional operation of the device at these or any other conditions beyond those indicated under "recommended operating conditions” is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. 2. The input and output voltage ratings may be exceeded if the input and output current ratings are observed. October 17, 1990 28

Philips Components—Signetics ACL Products AC11013: Product Specification, ACT11013: Objective Specification Dual 4-input NAND Schmitt-trigger 74AC/ACT11013 DC ELECTRICAL CHARACTERISTICS SYMBOL PARAMETER TEST CONDITIONS: Veo UNIT v [ain [ax [in [ax | wi [ woe | hn [wo | beef] “| best eet toe {toe | Por testis] par |e | 0 | lsofes[vepestae[ P| Hysteresis [ssfos [te [os[ie[ea [iz] oa] feefoe| fe Peet tsofeey aap fp owesua [aspaa] [ee Paap ae | [ss[se> [sal pee] se] Vou | Bighlover “vt Low=~ma [30 [ase [eal | [fF [| vy OH | output voltage or Vig [ss [aoe] [aa [ase[ [ae] [ov=-7om' [ss | | [sas] TT [aes] | tse per pepo Vor | come “gt [ostama [so[ [36 | [04s / CL | output voltage oF Vy = ~ 'oL = [ss Pee [fea] a6 [| oa] Faster [sf Pps P| [1 [rtenage ere [Waveorano [ss] [maf poor] fas oon Dan referer [ese fel Tel [el fot lol One in 3.4V, on frees BE TDL el NOTES: 1. Not more than one output should be tested at a time, and the duration of the test should not exceed 10ms. 2. This is the increase in supply current for each input that is at one of the specified TTL voltage levels rather than OV oF Vc. October 17, 1990 29

Philips Components—Signetics ACL Products AC11013: Product Specification, ACT11013: Objective Specification nS Dual 4-input NAND Schmitt-trigger T4AC/ACT11013 AC ELECTRICAL CHARACTERISTICS AT 3.3V +0.3V ~ TAACTIO13 SYMBOL PARAMETER WAVEFORM Ty = 425°C Ton = ote UNIT Min | Typ | Max | Min | Max | foun Propagation delay 1 25 87 25 97 | tee nA, nB, nC, nD to n¥ 23 8.7 23 99 ns AC ELECTRICAL CHARACTERISTICS AT 5.0V +0.5V 74AC11013 a SYMBOL PARAMETER WAVEFORM | Tumb = 425°C too unit | | —— tou Propagation delay 1 2.0 4.2 64 | 20 7A | tout nA, nB, nC, nD tonY 20 44 69 2.0 7.8 ns | AC ELECTRICAL CHARACTERISTICS AT 5.0V +0.5V T4ACT11013 ~ f SYMBOL PARAMETER WAVEFORM Tan = +25°C Tan oe? UNIT | | | | Min Max | Min | Max tun Propagation delay _ ' 15 15 | tout | nA, nB, nC, nD to n¥ 15 115 | ns AC WAVEFORMS 'RA,nB, nC, nD INPUT Va tome ey n¥ OUTPUT Va | Waveform 1. Waveforms Showing the Input (nA, nB, nC, nD) to Output (nY) | Propagation Delays WAVEFORM CONDITIONS ~ Vin = GND to Voc, —_ Ac Vour = Vor 10 V Vu = 50% Veo ‘OUT for t0 Vou Vin= GND to .0V, ACT Vy = 50% Veo Vy = 1.5V October 17, 1990 30

Philips Components—Signetics ACL Products AC11013: Product Specification, ACT 11013: Objective Specification SEE EEE Dual 4-input NAND Schmitt-trigger 74AC/ACT11013 ee TEST CIRCUIT Vee R R oO Tt on tL Test Circuit DEFINITIONS | C= Load capacitance, 50pF; includes jig ! and probe capacitance RU = Load resistor, 5000 | Ry= Termination resistance should be \\ equal to Zour of pulse generators Input pulses: PRR < 10MHz | t=t)=Sns i October 17, 1980 31