ACPL-072L-000E AVAGO | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 11
Technical content
Features
- Dual voltage operation (3.3V and 5V)
- Allow level shifting functionality
- Support high Speed datarate of 25 MBd
- Wide Temperature operation
- CMOS output and buffer input
- Compatible with CMOS and TTL logic level
- Lower power consumption with 3.3V supply
- Good AC performance with lower pulse width distortion
- Lead-free option available Specifications
- 3.3V and 5V CMOS Compatibility
- High Speed: DC to 25 MBd
- 6ns max. Pulse Width Distortion
- 40 ns max. Prop. Delay
- 20 ns max. Prop. Delay Skew
- 10 kV/ms min. Common Mode Rejection
- -40 °C to 105 °C Temperature Range
- Safety and Regulatory Approvals: UL Recognised - 5000Vrms for 1 min. per UL1577 for ACPL-772L for option 020 - 3750Vrms for 1 min. per UL1577 for ACPL-072L CSA Component Acceptance Notice #5 IEC/EN/DIN EN 60747-5-2 – VIORM = 630 Vpeak for ACPL-772L Option 060 – VIORM = 560 Vpeak for ACPL-072L Option 060
Applications
- Digital Fieldbus Isolation: DeviceNet, Profibus, SDS
- Multiplexed Data Transmission
- General Instrument and Data Acquisition
- Computer Peripheral interface
- Microprocessor System Interface SHIELD **VDD1 VI NC* GND 1 VDD2** VO GND 2 NC* IO LED1 CAUTION: It is advised that normal static precautions be taken in handling and assembly of this component to prevent damage and/or degradation, which may be induced by ESD. Lead (Pb) Free RoHS 6 fully compliant RoHS 6 fully compliant options available; -xxxE denotes a lead-free product * Pin 3 is the anode of the internal LED and must be left unconnected for guaranteed datasheet performance. Pin 7 is not connected internally. ** A 0.1uF bypass capacitor must be connected between pins 1 and 4, and 5 and 8. TRUTH TABLE (POSITIVE LOGIC) VI, INPUT LED1 VO, OUTPUT H OFF H L ON L
Ordering Information
ACPL-072L and ACPL-772L are UL Recognized with 3750 Vrms for 1 minute per UL1577. Part number Option Package Surface Mount Gull Wing Tape & Reel UL 5000 Vrms/ 1 Minute rating IEC/EN/DIN EN 60747- 5-2 Quantity RoHS Compliant Non RoHS Compliant ACPL-772L -000E - 300mil DIP-8 50 per tube -300E - X X 50 per tube -500E - X X X 1000 per reel -020E - X 50 per tube -320E - X X X 50 per tube -520E - X X X X 1000 per reel -060E - X 50 per tube -360E - X X X 50 per tube -560E - X X X X 1000 per reel ACPL-072L -000E No option SO-8 X 100 per tube -500E -500 X X 1500 per reel -060E -060 X X 100 per tube -560E -560 X X X 1500 per reel To order, choose a part number from the part number column and combine with the desired option from the option column to form an order entry. Example 1: ACPL-772L-560E to order product of Gull Wing Surface Mount package in Tape and Reel packaging with IEC/EN/DIN EN 60747-5-2 Safety Approval in RoHS compliant. Example 2: ACPL-072L to order product of Small Outline SO-8 package in tube packaging and non RoHS compliant. Option datasheets are available. Contact your Avago sales representative or authorized distributor for information. Device Selection Guide 8-Pin DIP (300 Mil) Small Outline SO-8 ACPL-772L ACPL-072L
ACPL-772L 8-Pin DIP Package 0.635 ± 0.25 (0.025 ± 0.010) 12 ° NOM. 9.65 ± 0.25 (0.380 ± 0.010) 0.635 ± 0.130 (0.025 ± 0.005) 7.62 ± 0.25 (0.300 ± 0.010) 5678 4321 9.65 ± 0.25 (0.380 ± 0.010) 6.350 ± 0.25 (0.250 ± 0.010) 1.016 (0.040) 1.27 (0.050) 10.9 (0.430) 2.0 (0.080) LAND PATTERN RECOMMENDATION 1.080 ± 0.320 (0.043 ± 0.013) 3.56 ± 0.13 (0.140 ± 0.005) 1.780 (0.070) MAX.1.19 (0.047) MAX. 2.54 (0.100) BSC DIMENSIONS IN MILLIMETERS (INCHES). LEAD COPLANARITY = 0.10 mm (0.004 INCHES). NOTE: FLOATING LEAD PROTRUSION IS 0.25 mm (10 mils) MAX. 0.254 + 0.076 - 0.051 (0.010 + 0.003) - 0.002) 9.65 ± 0.25 (0.380 ± 0.010) A XXXXV YYWW DATE CODE 1.080 ± 0.320 (0.043 ± 0.013) 2.54 ± 0.25 (0.100 ± 0.010) 0.51 (0.020) MIN. 0.65 (0.025) MAX. 4.70 (0.185) MAX. 2.92 (0.115) MIN. DIMENSIONS IN MILLIMETERS AND (INCHES). 5678 4321 5° TYP. 0.254 + 0.076 - 0.051 (0.010 + 0.003) - 0.002) 7.62 ± 0.25 (0.300 ± 0.010) 6.35 ± 0.25 (0.250 ± 0.010) TYPE NUMBER *OPTION 300 AND 500 NOT MARKED. NOTE: FLOATING LEAD PROTRUSION IS 0.25 mm (10 mils) MAX. OPTION 060 CODE* 3.56 ± 0.13 (0.140 ± 0.005)
ACPL-072L Small Outline SO-8 Package XXXV YWW 8 7 6 5 4321 5.994 ± 0.203 (0.236 ± 0.008) 3.937 ± 0.127 (0.155 ± 0.005) 0.406 ± 0.076 (0.050) BSC 5.080 ± 0.127 (0.200 ± 0.005) 3.175 ± 0.127 (0.060) 45 ° X 0.432 (0.017) 0.228 ± 0.025 (0.009 ± 0.001) TYPE NUMBER (LAST 3 DIGITS) DATE CODE 0.305 (0.012) MIN. TOTAL PACKAGE LENGTH (INCLUSIVE OF MOLD FLASH) DIMENSIONS IN MILLIMETERS (INCHES). LEAD COPLANARITY = 0.10 mm (0.004 INCHES) MAX. OPTION NUMBER 500 NOT MARKED. NOTE: FLOATING LEAD PROTRUSION IS 0.15 mm (6 mils) MAX. 0.203 ± 0.102 (0.008 ± 0.004) 7 ° PIN ONE 0 ~ 7 ° 7.49 (0.295) 1.9 (0.075) 0.64 (0.025) LAND PATTERN RECOMMENDATION
Both ACPL-072L and ACPL-772L are approved by the following organizations: Solder Reflow Temperature Profile Note: Non-halide flux should be used Recommended Pb-Free IR Profile Note: Non-halide flux should be used 217 ˚C RAMP-DOWN 6 ˚C/SEC. MAX. RAMP-UP 3 ˚C/SEC. MAX. 150 - 200 ˚C 260 +0/-5 ˚C t 25 ˚C to PEAK 60 to 150 SEC. 20-40 SEC. TIME WITHIN 5 ˚C of ACTUAL PEAK TEMPERATURE tp ts PREHEAT 60 to 180 SEC. tL T L T smax T smin T p TIME TEMPERATURE NO TES: THE TIME FROM 25 ˚C to PEAK TEMPERATURE = 8 MINUTES MAX. T smax = 200 ˚C, Tsmin = 150 ˚C TIME (SECONDS) TEMPERATURE (˚C)200 100 50 150100 200 250 300 SEC. 50 SEC. SEC. 160 ˚C 140 ˚C 150 ˚C PEAK TEMP. 245 ˚C PEAK TEMP. 240 ˚C PEAK TEMP. 230˚C SOLDERING TIME 200˚C PREHEATING TIME 150 ˚C, 90 + 30 SEC. 2.5˚ C ± 0.5˚C/SEC. TIGHT TYPICAL LOOSEROOM TEMPERATURE PREHEATING RATE 3˚C + 1 ˚C/- 0.5 ˚C/SEC. REFLOW HEATING RATE 2.5˚C ± 0.5 ˚C/SEC. IEC/EN/DIN EN 60747-5-2 Approved under: IEC 60747-5-2:1997 + A1:2002 EN 60747-5-2:2001 + A1:2002 DIN EN 60747-5-2 (VDE 0884 Teil 2):2003-01. (option 060 only) UL Approved under UL 1577, component recognition program up, File E55361. CSA Approved under CSA Component Acceptance Notice #5, File CA 88324.
Table 1. IEC/EN/DIN EN 60747-5-2 Insulation Characteristics*
- Isolation characteristics are guaranteed only within the safety maximum ratings which must be ensured by protective circuits in application.
Surface mount classification is class A in accordance with CECCOO802. DIN EN 60747-5-2, for a detailed description of Method a and Method b partial discharge test profiles. by means of protective circuits. Note: The surface mount classification is Class A in accordance with CECC 00802. Table 2. Insulation and Safety Related Specifications nals, shortest distance through air. nals, shortest distance path along body. between the emitter and detector. path along the surface of a printed circuit board between the solder fillets of the input and output leads must be considered. There are recommended techniques such as grooves and ribs which may be used on a printed circuit board to achieve desired creepage and clearances. Creepage and clearance distances will also change depending on factors such as pollution degree and insulation level.
Table 3. Absolute Maximum Ratings Table 4. Recommended Operating Conditions Table 5. Electrical Specifications Test conditions that are not specified can be anywhere within the recommended operating range. All typical specifications are at TA=+25°C , VDD1 = VDD2 = +3.3V.
Table 6. Switching Specifications Test conditions that are not specified can be anywhere within the recommended operating range. All typical specifications are at TA=+25°C, VDD1 = VDD2 = +3.3V. Table 7. Package Characteristics All typical specifications are at TA = 25°C.
- Absolute Maximum ambient operating temperature means the device will not be damaged if operated under these conditions. It does not
- The LED is ON when VI is low and OFF when VI is high.
- tPHL propagation delay is measured from the 50% level on the falling edge of the VI signal to the 50% level of the falling edge of the VO signal. tPLH
propagation delay is measured from the 50% level on the rising edge of the VI signal to the 50% level of the rising edge of the VO signal.
- The minimum pulse width is the shortest pulse width at which the specified pulse width distortion is guaranteed.
- The maximum data rate is the fastest data rate at which the specified pulse width distortion is guaranteed.
- PWD is defined as |tPHL - tPLH|. %PWD (percent pulse width distortion) is equal to the PWD divided by pulse width.
- tPSK is equal to the magnitude of the worst case difference in tPHL and/or tPLH that will be seen between units at any given temperature within the
recommended operating conditions.
Application Information
Bypassing and PC Board Layout The ACPL-x72L optocouplers are extremely easy to use. No external interface circuitry is required because ACPL- x72L uses high speed CMOS IC technology allowing CMOS logic to be connected directly to the inputs and outputs. As shown in Figure 7, the only external components required for proper operation are two bypass capacitors. Capacitor values should be between 0.01 mF and 0.1 mF. For each capacitor, the total lead length between both ends of the capacitor and power supply pins should not exceed 20mm. Figure 8 illustrates the recommended printed circuit board layout for ACPL-x72L. Figure 7. Recommended Circuit Diagram Figure 8. Recommended Printed Circuit Board Layout how quickly a logic signal propagates through a system. from high to low. Please see Figure 9. Figure 9. Signal plot shows how propagation delay is defined