74ALVC164245 PHILIPS | Alldatasheet
Document overview
- Manufacturer or author: Provided By www.digicamel.com(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 19
Technical content
- General description The 74ALVC164245 is a high-performance, low-power, low-voltage, Si-gate CMOS device, superior to most advanced CMOS compatible TTL families. The 74ALVC164245 is a 16-bit (dual octal) dual supply translating transceiver featuring non-inverting 3-state bus compatible outputs in both send and receive directions. It is designed to interface between a 3 V and 5 V bus in a mixed 3 V and 5 V supply environment. This device can be used as two 8-bit transceivers or one 16-bit transceiver. The direction control inputs (1DIR and 2DIR) determine the direction of the data flow. nDIR (active HIGH) enables data from nA ports to nB ports. nDIR (active LOW) enables data from nB ports to nA ports. The output enable inputs (1 OE and 2OE), when HIGH, disable both nA and nB ports by placing them in a high-impedance OFF-state. The nB ports interface with the 5 V bus. The nA ports interface with the 3 V bus. In suspend mode, when one of the supply voltages is zero, there will be no current flow from the non-zero supply towards the zero supply. The A-outputs must be set 3-state and the voltage on the A-bus must be smaller than V diode (typical 0.7 V). VCCB ≥ VCCA (except in suspend mode). 2. Features ■ 5 V tolerant inputs/outputs for interfacing with 5 V logic ■ Wide supply voltage range: ◆ 3 V port (VCCA ): 1.5 V to 3.6 V ◆ 5 V port (VCCB ): 1.5 V to 5.5 V. ■ CMOS low power consumption ■ Direct interface with TTL levels ■ Control inputs voltage range from 2.7 V to 5.5 V ■ Inputs accept voltages up to 5.5 V ■ High-impedance outputs when VCCA or VCCB = 0 V ■ Complies with JEDEC standard JESD8-B/JESD36 ■ ESD protection: ◆ HBM EIA/JESD22-A114-B exceeds 2000 V ◆ MM EIA/JESD22-A115-A exceeds 200 V. ■ Specified from−40 °C to +85°C and −40 °C to +125°C. 74ALVC164245 16-bit dual supply translating transciever; 3-state Rev. 02 — 1 June 2004 Product data sheet
9397 750 13248 © Koninklijke Philips Electronics N.V. 2004. All rights reserved. Product data sheet Rev. 02 — 1 June 2004 2 of 19 Philips Semiconductors 74ALVC164245 16-bit dual supply translating transceiver; 3-state 3. Quick reference data [1] C PD is used to determine the dynamic power dissipation (PD inµW). PD = CPD × VCC 2 × fi× N +Σ(CL × VCC 2 × fo) where: fi = input frequency in MHz; fo = output frequency in MHz; C L = output load capacitance in pF; VCC = supply voltage in Volts; N = total load switching outputs; Σ(C L × VCC 2 × fo) = sum of the outputs. [2] The condition is VI = GND to VCC . 4. Ordering information Table 1: Quick reference data GND = 0 V; Tamb = 25°C; tr = tf≤ 2.5 ns. Symbol Parameter Conditions Min Typ Max Unit tPHL , tPLH propagation delay nAn to nBn C L = 50 pF; VCCB = 4.5 V to 5.5 V; VCCA = 3.0 V to 3.6 V - 2.9 - ns propagation delay nBn to nAn C L = 50 pF; VCCB = 4.5 V to 5.5 V; VCCA = 3.0 V to 3.6 V - 2.5 - ns propagation delay nAn to nBn C L = 50 pF; VCCB = 3.0 V to 3.6 V; VCCA = 2.3 V to 2.7 V - 3.3 - ns propagation delay nBn to nAn C L = 50 pF; VCCB = 3.0 V to 3.6 V; VCCA = 2.3 V to 2.7 V - 3.0 - ns C I input capacitance - 4.0 - pF C I/O input/output capacitance A and B port - 5.0 - pF C PD power dissipation capacitance 5 V port: nAn to nBn V CCB =5V ;V CCA = 3.3 V [1][2] outputs enabled - 30 - pF outputs disabled - 15 - pF power dissipation capacitance 3 V port: nBn to nA V CCB =5V ;V CCA = 3.3 V [1][2] outputs enabled - 40 - pF outputs disabled - 5 - pF Table 2: Ordering information Type number Temperature range Package Name Description Version 74ALVC164245DGG −40 °C to +125°C TSSOP48 plastic thin shrink small outline package; 48 leads; body width 6.1 mm SOT362-1 74ALVC164245DL −40 °C to +125°C SSOP48 plastic shrink small outline package; 48 leads; body width 7.5 mm SOT370-1
9397 750 13248 © Koninklijke Philips Electronics N.V. 2004. All rights reserved. Product data sheet Rev. 02 — 1 June 2004 3 of 19 Philips Semiconductors 74ALVC164245 16-bit dual supply translating transceiver; 3-state 5. Functional diagram Fig 1. Logic symbol. 1DIR 1B0 1B1 1B2 1B3 1B4 1B5 1B6 1B7 2B0 2B1 2B2 2B3 2B4 2B5 2B6 2B7 1A0 1A1 1A2 1A3 1A4 1A5 1A6 1A7 2A0 2A1 2A2 2A3 2A4 2A5 2A6 2A7 1OE 2DIR 2OE 001aaa789
9397 750 13248 © Koninklijke Philips Electronics N.V. 2004. All rights reserved. Product data sheet Rev. 02 — 1 June 2004 4 of 19 Philips Semiconductors 74ALVC164245 16-bit dual supply translating transceiver; 3-state Fig 2. IEC logic symbol. 3EN1[BA] 6EN1[BA] 3EN2[AB] 6EN2[AB] 1A0 2A1 2A0 2A2 2A3 2A4 2A5 2A6 2A7 2B1 2B2 2B3 2B4 2B5 2B6 2B7 1OE 1DIR 001aaa790 1A1 1A2 1A3 1A4 1A5 1A6 1A7 1B0 2B0 1B1 1B2 1B3 1B4 1B5 1B6 1B7 2OE 2DIR
9397 750 13248 © Koninklijke Philips Electronics N.V. 2004. All rights reserved. Product data sheet Rev. 02 — 1 June 2004 5 of 19 Philips Semiconductors 74ALVC164245 16-bit dual supply translating transceiver; 3-state 6. Pinning information
6.1 Pinning
6.2 Pin description
Fig 3. Pin configuration (T)SSOP48. 164245 1DIR 1OE 1B0 1A0 1B1 1A1 GND GND 1B2 1A2 1B3 1A3 V CCB VCCA 1B4 1A4 1B5 1A5 GND GND 1B6 1A6 1B7 1A7 2B0 2A0 2B1 2A1 GND V CC 2B2 2A4 2B3 2A3 V CCB VCCA 2B4 2A4 2B5 2A5 GND GND 2B6 2A6 2B7 2A7 2DIR 2OE 001aab037 Table 3: Pin description Symbol Pin Description 1DIR 1 direction control input 1B0 2 data input/output 1B1 3 data input/output GND 4, 10, 15, 21, 28, 34, 39, 45 ground (0 V) 1B2 5 data input/output 1B3 6 data input/output V CCB 7, 18 supply voltage (5 V bus) 1B4 8 data input/output 1B5 9 data input/output 1B6 11 data input/output 1B7 12 data input/output
9397 750 13248 © Koninklijke Philips Electronics N.V. 2004. All rights reserved. Product data sheet Rev. 02 — 1 June 2004 6 of 19 Philips Semiconductors 74ALVC164245 16-bit dual supply translating transceiver; 3-state 2B0 13 data input/output 2B1 14 data input/output 2B2 16 data input/output 2B3 17 data input/output 2B4 19 data input/output 2B5 20 data input/output 2B6 22 data input/output 2B7 23 data input/output 2DIR 24 direction control input OE 25 output enable input (active LOW) 2A7 26 data input/output 2A6 27 data input/output 2A5 29 data input/output 2A4 30 data input/output V CCA 31, 42 supply voltage (3 V bus) 2A3 32 data input/output 2A2 33 data input/output 2A1 35 data input/output 2A0 36 data input/output 1A7 37 data input/output 1A6 38 data input/output 1A5 40 data input/output 1A4 41 data input/output 1A3 43 data input/output 1A2 44 data input/output 1A1 46 data input/output 1A0 47 data input/output OE 48 output enable input (active LOW) n.c. - not connected Table 3: Pin description …continued Symbol Pin Description
9397 750 13248 © Koninklijke Philips Electronics N.V. 2004. All rights reserved. Product data sheet Rev. 02 — 1 June 2004 7 of 19 Philips Semiconductors 74ALVC164245 16-bit dual supply translating transceiver; 3-state 7. Functional description
7.1 Function table
[1] H = HIGH voltage level; L = LOW voltage level; X = don’t care; Z = high-impedance OFF-state. 8. Limiting values [1] The performance capability of a high-performance integrated circuit in conjunction with its thermal environment can create junction temperatures which are detrimental to reliability. The maximum junction temperature of this integrated circuit should not exceed 150°C. [2] The input and output voltage ratings may be exceeded if the input and output current ratings are observed. [3] For (T)SSOP48 packages: above 60°C the value of P tot derates linearly with 5.5 mW/K. Table 4: Function table[1] Inputs Outputs nOE nDIR nAn nBn L L A = B inputs L H inputs B = A HXZZ Table 5: Limiting values In accordance with the Absolute Maximum Rating System (IEC 60134). Voltages are referenced to GND (ground = 0 V). SeeTable note1. Symbol Parameter Conditions Min Max Unit VCCB supply voltage B port VCCB ≥ VCCA −0.5 +6.0 V VCCA supply voltage A port VCCB ≥ VCCA −0.5 +4.6 V IIK input diode current VI<0V - −50 mA VI input voltage [2] −0.5 +6.0 V VI/O input voltage range for I/Os −0.5 V CC + 0.5 V IOK output diode current VO >V CC or VO <0V - ±50 mA VO output voltage output HIGH or LOW state [2] −0.5 V CC + 0.5 V output 3-state [2] −0.5 +6.0 V IO output source or sink current VO =0Vt oV CC - ±50 mA ICC , IGND VCC or GND current - ±100 mA Tstg storage temperature −65 +150 °C Ptot power dissipation SSOP and TSSOP package Tamb = −40 °C to +125°C [3] - 500 mW
9397 750 13248 © Koninklijke Philips Electronics N.V. 2004. All rights reserved. Product data sheet Rev. 02 — 1 June 2004 8 of 19 Philips Semiconductors 74ALVC164245 16-bit dual supply translating transceiver; 3-state 9. Recommended operating conditions 10. Static characteristics Table 6: Recommended operating conditions Symbol Parameter Conditions Min Typ Max Unit VCCB supply voltage B port VCCB ≥ VCCA maximum speed performance 2.7 - 5.5 V low-voltage applications 1.5 - 5.5 V VCCA supply voltage A port VCCB ≥ VCCA maximum speed performance 2.7 - 3.6 V low-voltage applications 1.5 - 3.6 V VI input voltage control inputs 0 - 5.5 V VI/O input voltage A port 0 - V CCA V B port 0 - V CCB V VO output voltage A port 0 - V CCA V B port 0 - V CCB V Tamb operating ambient temperature −40 - +125 °C t r, tf input rise and fall times VCCA = 2.7 V to 3.0 V 0 - 20 ns/V VCCA = 3.0 V to 3.6 V 0 - 10 ns/V VCCB = 3.0 V to 4.5 V 0 - 20 ns/V VCCB = 4.5 V to 5.5 V 0 - 10 ns/V Table 7: Static characteristics At recommended operating conditions; voltages are referenced to GND (ground = 0 V). Symbol Parameter Conditions Min Typ Max Unit Tamb = −40 °C to +85°C [1] VIH HIGH-level input voltage B port V CCB = 3.0 V to 5.5 V [2] 2.0 - - V A port V CCA = 3.0 V to 3.6 V 2.0 - - V VCCA = 2.3 V to 2.7 V [2] 1.7 - - V VIL LOW-level input voltage B port V CCB = 4.5 V to 5.5 V [2] - - 0.8 V VCCB = 3.0 V to 3.6 V [2] - - 0.7 V A port V CCA = 3.0 V to 3.6 V - - 0.8 V VCCA = 2.3 V to 2.7 V [2] - - 0.7 V
9397 750 13248 © Koninklijke Philips Electronics N.V. 2004. All rights reserved. Product data sheet Rev. 02 — 1 June 2004 9 of 19 Philips Semiconductors 74ALVC164245 16-bit dual supply translating transceiver; 3-state VOH HIGH-level output voltage B port V I=V IH or VIL IO = −24 mA; VCCB = 4.5 V V CCB − 0.8 - - V IO = −12 mA; VCCB = 4.5 V V CCB − 0.5 - - V IO = −18 mA; VCCB = 3.0 V V CCB − 0.8 - - V IO = −100 µA; VCCB = 3.0 V V CCB − 0.2 VCCB -V A port V I=V IH or VIL IO = −24 mA; VCCA = 3.0 V V CCA − 0.7 - - V IO = −100 µA; VCCA = 3.0 V V CCA − 0.2 - - V IO = −12 mA; VCCA = 2.7 V V CCA − 0.5 - - V IO = −8 mA; VCCA = 2.3 V V CCA − 0.6 - - V IO = −100 µA; VCCA = 2.3 V V CCA − 0.2 VCCA -V VOL LOW-level output voltage B port V I=V IH or VIL IO = 24 mA; VCCB = 4.5 V - - 0.55 V IO = 12 mA; VCCB = 4.5 V - - 0.40 V IO = 100µA; VCCB = 4.5 V - - 0.20 V IO = 18 mA; VCCB = 3.0 V - - 0.55 V IO = 100µA; VCCB = 3.0 V - - 0.20 V A port V I=V IH or VIL IO = 24 mA; VCCA = 3.0 V - - 0.55 V IO = 100µA; VCCA = 3.0 V - - 0.20 V IO = 12 mA; VCCA = 2.7 V - - 0.40 V IO = 12 mA; VCCA = 2.3 V - - 0.60 V IO = 100µA; VCCA = 2.3 V - - 0.20 V ILI input leakage current VI= 5.5 V or GND - ±0.1 ±5 µA IOZ 3-state output OFF-state current VI=V IH or VIL; VO =V CC or GND [3] - ±0.1 ±10 µA ICC quiescent supply current VI=V CC or GND; IO = 0 A - 0.1 40 µA ΔICC additional quiescent supply current per control pin V I=V CC − 0.6 V; IO =0A [4] - 5 500 µA C I input capacitance - 4.0 - pF C I/O input/output capacitance A and B port - 5.0 - pF Tamb = −40 °C to +125°C VIH HIGH-level input voltage B port V CCB = 3.0 V to 5.5 V [2] 2.0 - - V A port V CCA = 3.0 V to 3.6 V 2.0 - - V VCCA = 2.3 V to 2.7 V [2] 1.7 - - V Table 7: Static characteristics …continued At recommended operating conditions; voltages are referenced to GND (ground = 0 V). Symbol Parameter Conditions Min Typ Max Unit
9397 750 13248 © Koninklijke Philips Electronics N.V. 2004. All rights reserved. Product data sheet Rev. 02 — 1 June 2004 10 of 19 Philips Semiconductors 74ALVC164245 16-bit dual supply translating transceiver; 3-state [1] All typical values are measured at VCCB = 5.0 V, VCCA = 3.3 V and Tamb =2 5°C. [2] If VCCA < 2.7 V, the switching levels at all inputs are not TTL compatible. [3] For transceivers, the parameter IOZ includes the input leakage current. VIL LOW-level input voltage B port V CCB = 4.5 V to 5.5 V [2] - - 0.8 V VCCB = 3.0 V to 3.6 V [2] - - 0.7 V A port V CCA = 3.0 V to 3.6 V - - 0.8 V VCCA = 2.3 V to 2.7 V [2] - - 0.7 V VOH HIGH-level output voltage B port V I=V IH or VIL IO = −24 mA; VCCB = 4.5 V V CCB − 1.2 - - V IO = −12 mA; VCCB = 4.5 V V CCB − 0.8 - - V IO = −18 mA; VCCB = 3.0 V V CCB − 1.0 - - V IO = −100 µA; VCCB = 3.0 V V CCB − 0.3 VCCB -V A port V I=V IH or VIL IO = −24 mA; VCCA = 3.0 V V CCA − 1.0 - - V IO = −100 µA; VCCA = 3.0 V V CCA − 0.3 - - V IO = −12 mA; VCCA = 2.7 V V CCA − 0.8 - - V IO = −8 mA; VCCA = 2.3 V V CCA − 0.6 - - V IO = −100 µA; VCCA = 2.3 V V CCA − 0.3 VCCA -V VOL LOW-level output voltage B port V I=V IH or VIL IO = 24 mA; VCCB = 4.5 V - - 0.60 V IO = 12 mA; VCCB = 4.5 V - - 0.80 V IO = 100µA; VCCB = 4.5 V - - 0.30 V IO = 18 mA; VCCB = 3.0 V - - 0.80 V IO = 100µA; VCCB = 3.0 V - - 0.30 V A port V I=V IH or VIL IO = 24 mA; VCCA = 3.0 V - - 0.80 V IO = 100µA; VCCA = 3.0 V - - 0.30 V IO = 12 mA; VCCA = 2.7 V - - 0.60 V IO = 12 mA; VCCA = 2.3 V - - 0.60 V IO = 100µA; VCCA = 2.3 V - - 0.20 V ILI input leakage current VI= 5.5 V or GND - ±0.1 ±10 µA IOZ 3-state output OFF-state current VI=V IH or VIL; VO =V CC or GND [3] - ±0.1 ±20 µA ICC quiescent supply current VI=V CC or GND; IO = 0 A - 0.1 80 µA ΔICC additional quiescent supply current per control pin V I=V CC − 0.6 V; IO =0A [4] - 5 5000 µA Table 7: Static characteristics …continued At recommended operating conditions; voltages are referenced to GND (ground = 0 V). Symbol Parameter Conditions Min Typ Max Unit
9397 750 13248 © Koninklijke Philips Electronics N.V. 2004. All rights reserved. Product data sheet Rev. 02 — 1 June 2004 11 of 19 Philips Semiconductors 74ALVC164245 16-bit dual supply translating transceiver; 3-state 11. Dynamic characteristics Table 8: Dynamic characteristics GND = 0 V; tr = tf≤ 2.5 ns; CL = 50 pF; seeFigure6. Symbol Parameter Conditions Min Typ Max Unit Tamb =−40 °C to +85°C [1] tPHL , tPLH propagation delay nAn to nBn see Figure4 propagation delay nBn to nAn see Figure4 tPZH , tPZL 3-state output enable time nOE to nBn see Figure5 3-state output enable time nOE to nAn see Figure5 tPHZ , tPLZ 3-state output disable time nOE to nBn see Figure5 3-state output disable time nOE to nAn see Figure5 C PD power dissipation capacitance 5 V port: nAn to nBn V CCB = 5 V; VCCA = 3.3 V [2][3] outputs enabled - 30 - pF outputs disabled - 15 - pF power dissipation capacitance 3 V port: nBn to nA V CCB = 5 V; VCCA = 3.3 V [2][3] outputs enabled - 40 - pF outputs disabled - 5 - pF
9397 750 13248 © Koninklijke Philips Electronics N.V. 2004. All rights reserved. Product data sheet Rev. 02 — 1 June 2004 12 of 19 Philips Semiconductors 74ALVC164245 16-bit dual supply translating transceiver; 3-state [1] All typical values are measured at nominal voltage for VCCB and VCCA and at Tamb =2 5°C. [2] C PD is used to determine the dynamic power dissipation (PD inµW). PD = CPD × VCC 2 × fi× N +Σ(CL × VCC 2 × fo) where: fi = input frequency in MHz; fo = output frequency in MHz; C L = output load capacitance in pF; VCC = supply voltage in Volts; N = total load switching outputs; Σ(C L × VCC 2 × fo) = sum of the outputs. [3] The condition is VI = GND to VCC . Tamb =−40 °C to +125°C tPHL , tPLH propagation delay nAn to nBn see Figure4 propagation delay nBn to nAn see Figure4 tPZH , tPZL 3-state output enable time nOE to nBn see Figure5 3-state output enable time nOE to nAn see Figure5 tPHZ , tPLZ 3-state output disable time nOE to nBn see Figure5 3-state output disable time nOE to nAn see Figure5 Table 8: Dynamic characteristics …continued GND = 0 V; tr = tf≤ 2.5 ns; CL = 50 pF; seeFigure6. Symbol Parameter Conditions Min Typ Max Unit
9397 750 13248 © Koninklijke Philips Electronics N.V. 2004. All rights reserved. Product data sheet Rev. 02 — 1 June 2004 13 of 19 Philips Semiconductors 74ALVC164245 16-bit dual supply translating transceiver; 3-state 12. AC waveforms Measurement points are given inTable9. VOL and VOH are typical output voltage drop that occur with the output load. Fig 4. Input (nAn, nBn) to output (nBn, nAn) propagation delays. Table 9: Measurement points Direction Supply voltage Input Output VCCA VCCB VI VM VM Measurement points are given inTable10. VOL and VOH are typical output voltage drop that occur with output load. Fig 5. 3-state enable and disable times. 001aaa792 nAn, nBn input nBn, nAn output tPHL tPLH GND VI VM VM VOH VOL 001aaa793 tPLZ tPHZ outputs disabled outputs enabled VY VX outputs enabled Qn output LOW-to-OFF OFF-to-LOW Qn output HIGH-to-OFF OFF-to-HIGH nOE input VI VOL VOH VCC VM VM GND GND tPZL tPZH VM VM
9397 750 13248 © Koninklijke Philips Electronics N.V. 2004. All rights reserved. Product data sheet Rev. 02 — 1 June 2004 14 of 19 Philips Semiconductors 74ALVC164245 16-bit dual supply translating transceiver; 3-state Table 10: Measurement points Direction Supply voltage Input Output VCCA VCCB VI VM VM VX VY Test data is given inTable11. Definitions for test circuits: R L = Load resistor. C L = Load capacitance including jig and probe capacitance. R T = Termination resistance should be equal to the output impedance Zo of the pulse generator. Fig 6. Load circuitry for switching times. VEXT VCC VI VO mna616 D.U.T. C LR T R L R L PULSE GENERATOR Table 11: Test data Direction Supply voltage Load VEXT VCCA VCCB C L R L tPLH , tPHL tPZH , tPHZ tPZL , tPLZ A port to B port 2.3 V to 2.7 V 2.7 V to 3.6 V 50 pF 500Ω open GND 2 × VCC A port to B port 2.7 V to 3.6 V 4.5 V to 5.5 V 50 pF 500Ω open GND 2 × VCC
9397 750 13248 © Koninklijke Philips Electronics N.V. 2004. All rights reserved. Product data sheet Rev. 02 — 1 June 2004 15 of 19 Philips Semiconductors 74ALVC164245 16-bit dual supply translating transceiver; 3-state 13. Package outline Fig 7. Package outline SSOP48. UNIT A 1 A 2 A 3 bp cD (1) E (1) eH E LL p QZ ywv q REFERENCESOUTLINE VERSION EUROPEAN PROJECTION ISSUE DATE IEC JEDEC JEITA mm 0.4 0.2 2.35 2.20 0.25 0.3 0.2 0.22 0.13 16.00 15.75 7.6 10.1 1.0 0.6 1.2 1.0 0.85 0.40 o o0.18 0.1 DIMENSIONS (mm are the original dimensions) Note 1. Plastic or metal protrusions of 0.25 mm maximum per side are not included. SOT370-1 99-12-27 03-02-19 (1) w M bp D H E E Z e c v M A X A y 48 25 MO-118 241 q AA 1 A 2 Lp Q detail X L (A )3 pin 1 index 0 5 10 mm scale SSOP48: plastic shrink small outline package; 48 leads; body width 7.5 mm SOT370-1 A max. 2.8
9397 750 13248 © Koninklijke Philips Electronics N.V. 2004. All rights reserved. Product data sheet Rev. 02 — 1 June 2004 16 of 19 Philips Semiconductors 74ALVC164245 16-bit dual supply translating transceiver; 3-state Fig 8. Package outline TSSOP48. UNIT A 1 A 2 A 3 bp cD (1) E (2) eH E LL p QZ ywv q REFERENCESOUTLINE VERSION EUROPEAN PROJECTION ISSUE DATE IEC JEDEC JEITA mm 0.15 0.05 0.2 0.1 o o0.1 DIMENSIONS (mm are the original dimensions). Notes 1. Plastic or metal protrusions of 0.15 mm maximum per side are not included. 2. Plastic interlead protrusions of 0.25 mm maximum per side are not included. SOT362-1 99-12-27 03-02-19 w M q AA 1 A 2 D Lp Q detail X E Z e c L X (A )3 0.25 12 4 48 25 y pin 1 index b H 1.05 0.85 0.28 0.17 0.2 0.1 12.6 12.4 6.2 6.0 0.5 1 0.258.3 7.9 0.50 0.35 0.8 0.40.080.8 0.4 p E v M A A TSSOP48: plastic thin shrink small outline package; 48 leads; body width 6.1 mm SOT362-1 A max. 1.2 0 2.5 5 mm scale MO-153
9397 750 13248 © Koninklijke Philips Electronics N.V. 2004. All rights reserved. Product data sheet Rev. 02 — 1 June 2004 17 of 19 Philips Semiconductors 74ALVC164245 16-bit dual supply translating transceiver; 3-state 14. Revision history Table 12: Revision history Document ID Release date Data sheet status Change notice Order number Supersedes 74ALVC164245_2 20040601 Product data - 9397 750 13248 74ALVC164245_1 Modifications:
- The format of this data sheet has been redesigned to comply with the current presentation and information standard of Philips Semiconductors.
- Table2: VFBGA56 type added
- Table7: Values for Tamb = −40 °C to +125°C added
- Table8: Values for Tamb = −40 °C to +125°C added 74ALVC164245_1 19980826 Product specification - 9397 750 04564 -
Philips Semiconductors 74ALVC164245 16-bit dual supply translating transceiver; 3-state 9397 750 13248 © Koninklijke Philips Electronics N.V. 2004. All rights reserved. Product data sheet Rev. 02 — 1 June 2004 18 of 19 15. Data sheet status [1] Please consult the most recently issued data sheet before initiating or completing a design. [2] The product status of the device(s) described in this data sheet may have changed since this data sheet was published. The latest information is available on the Internet at URL http://www.semiconductors.philips.com. [3] For data sheets describing multiple type numbers, the highest-level product status determines the data sheet status. 16. Definitions Short-form specification —The data in a short-form specification is extracted from a full data sheet with the same type number and title. For detailed information see the relevant data sheet or data handbook. Limiting values definition — Limiting values given are in accordance with the Absolute Maximum Rating System (IEC 60134). Stress above one or more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation of the device at these or at any other conditions above those given in the Characteristics sections of the specification is not implied. Exposure to limiting values for extended periods may affect device reliability. Application information — Applications that are described herein for any of these products are for illustrative purposes only. Philips Semiconductors make no representation or warranty that such applications will be suitable for the specified use without further testing or modification. 17. Disclaimers Life support —These products are not designed for use in life support appliances, devices, or systems where malfunction of these products can reasonably be expected to result in personal injury. Philips Semiconductors customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Philips Semiconductors for any damages resulting from such application. Right to make changes —Philips Semiconductors reserves the right to make changes in the products - including circuits, standard cells, and/or software - described or contained herein in order to improve design and/or performance. When the product is in full production (status ‘Production’), relevant changes will be communicated via a Customer Product/Process Change Notification (CPCN). Philips Semiconductors assumes no responsibility or liability for the use of any of these products, conveys no license or title under any patent, copyright, or mask work right to these products, and makes no representations or warranties that these products are free from patent, copyright, or mask work right infringement, unless otherwise specified. 18. Contact information For additional information, please visit: http://www.semiconductors.philips.com For sales office addresses, send an email to: sales.addresses@www.semiconductors.philips.com Level Data sheet status[1] Product status[2][3] Definition I Objective data Development This data sheet contains data from the objective specification for product development. Philips Semiconductors reserves the right to change the specification in any manner without notice. II Preliminary data Qualification This data sheet contains data from the preliminary specification. Supplementary data will be published at a later date. Philips Semiconductors reserves the right to change the specification without notice, in order to improve the design and supply the best possible product. III Product data Production This data sheet contains data from the product specification. Philips Semiconductors reserves the right to make changes at any time in order to improve the design, manufacturing and supply. Relevant changes will be communicated via a Customer Product/Process Change Notification (CPCN).
© Koninklijke Philips Electronics N.V. 2004 All rights are reserved. Reproduction in whole or in part is prohibited without the prior written consent of the copyright owner. The information presented in this document does not form part of any quotation or contract, is believed to be accurate and reliable and may be changed without notice. No liability will be accepted by the publisher for any consequence of its use. Publication thereof does not convey nor imply any license under patent- or other industrial or intellectual property rights. Date of release: 1 June 2004 Document order number: 9397 750 13248 Published in The Netherlands Philips Semiconductors 74ALVC164245 16-bit dual supply translating transceiver; 3-state 19. Contents