AA4040SYSK TO-GRACE | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 6

Technical content

Features

z Single color. z Suitable for all SMT assembly and solder process. z Available on tape and reel. z Ideal for backlighting. z Package : 500pcs / reel. z Moisture sensitivity level : level 3. z RoHS compliant. Des cription The Supe r Bright Yellow device is made with AlGaInP (on GaAs substrate) light emitting diode chip. Packag e Dimensions Not es: 1. All dimensions are in millimeters (inches). 2. Tolerance is ±0.25(0.01") unless otherwise noted. 3. The specifications, characteristics and technical data described in the datasheet are subject to change without prior notice. 4. The device has a single mounting surface. The device must be mounted according to the specifications. 香港至恩科技有限公司 www.to-grace.com 公司授权代理销售LITE-ON:光耦，贴片LED灯等 进口原装，现货供应，价格优势，技术支持 电话：0755-83464948 传真：0755-83464076 A ll data sheet.com

SPEC NO: DSAL0885 REV NO: V.6B DATE: MAR/16/2015 PAGE: 2 OF 6 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: P.Cheng ERP: 1201006683 Handling Precautions Compare to epoxy encapsulant that is hard and brittle, silicone is softer and flexible. Although its characteristic significantly reduces thermal stress, it is more susceptible to damage by external mechanical force. As a result, special handling precautions need to be observed during assembly using silicone encapsulated LED products. Failure to comply might lead to damage and premature failure of the LED. 1. Handle the component along the side surfaces by using forceps or appropriate tools. 2. Do not directly touch or handle the silicone lens surface. It may damage the internal circuitry. 3. As silicone encapsulation is permeable to gases, some corrosive substances such as H2S might corrode silver plating of leadframe. Special care should be taken if an LED with silicone encapsulation is to be used near such substances. A ll data sheet.com

SPEC NO: DSAL0885 REV NO: V.6B DATE: MAR/16/2015 PAGE: 3 OF 6 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: P.Cheng ERP: 1201006683 Selection Guide Absolute Maximum Ratings at TA=25°C Electrical / Optical Characteristics at TA=25°C Note: 1. 1/10 Duty Cycle, 0.1ms Pulse Width. Part No. Dice Lens Type Viewing Angle [1] Min. Typ. 2 θ1/2 AA4040SYSK Super Bright Yellow (AlGaInP) Water Clear 120 250 120° Iv (mcd) [2] @ 20mA Symbol Parameter Device Typ. Max. Units Test Conditions λpeak Peak Wavelength Super Bright Yellow 590 nm I F=20mA λD [1] Dominant Wavelength Super Bright Yellow 590 nm I F=20mA Δλ1/2 Spectral Line Half-width Super Bright Yellow 20 nm I F=20mA C Capacitance Super Bright Yellow 20 pF V F=0V;f=1MHz VF [2] Forward Voltage Super Bright Yellow 2 2.5 V I F=20mA IR Reverse Current Super Bright Yellow 10 uA V R=5V Parameter Super Bright Yellow Units Power dissipation 75 mW DC Forward Current 30 mA Peak Forward Current [1] 175 mA Reverse Voltage 5 V Operating Temperature -40°C To +85°C Storage Temperature -40°C To +85°C Notes: 1. θ1/2 is the angle from optical centerline where the luminous intensity is 1/2 of the optical peak value. 2. Luminous intensity/ luminous Flux: +/-15%. 3. Luminous intensity value is traceable to the CIE127-2007 compliant national standards. Notes: 1. Wavelength: +/-1nm. 2. Forward Voltage: +/-0.1V. 3. Wavelength value is traceable to the CIE127-2007 compliant national standards. 4. Excess driving current and/or operating temperature higher than recommended conditions may result in severe light degradation or premature failure. A ll data sheet.com

SPEC NO: DSAL0885 REV NO: V.6B DATE: MAR/16/2015 PAGE: 4 OF 6 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: P.Cheng ERP: 1201006683 Super Bright Yellow AA4040SYSK A ll data sheet.com

SPEC NO: DSAL0885 REV NO: V.6B DATE: MAR/16/2015 PAGE: 5 OF 6 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: P.Cheng ERP: 1201006683 AA4040SYSK Reflow soldering is recommended and the soldering profile is shown below. Other soldering methods are not recommended as they might cause damage to the product. Recommended Soldering Pattern (Units : mm; Tolerance: ± 0.1) Reel Dimension Tape Dimensions (Units : mm) A ll data sheet.com

SPEC NO: DSAL0885 REV NO: V.6B DATE: MAR/16/2015 PAGE: 6 OF 6 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: P.Cheng ERP: 1201006683 PACKING & LABEL SPECIFICATIONS AA4040SYSK Terms and conditions for the usage of this document 1. The information included in this document reflects representative usage scenarios and is intended for technical reference only. 2. The part number, type, and specifications mentioned in this document are subject to future change and improvement without notice. Before production usage customer should refer to the latest datasheet for the updated specifications. 3. When using the products referenced in this document, please make sure the produc t is being operated within the environmental and electrical limits specified in the datasheet. If customer usage exceeds the specified limits, Kingbright will not be responsible for any subsequent issues. 4. The information in this document applies to typical usage in consumer electronics applicati ons. If customer's application ha s special reliability requirements or have life-threatening liabilities, such as automotive or m edical usage, please consult with Kingbright representative for further assistance. 5. The contents and information of this document may not be reproduced or re-transmitted without permission by Kingbright. 6. All design applications should refer to Kingbright application notes available at http://www.KingbrightUSA.com/ApplicationNotes A ll data sheet.com