A800ERW MPD | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 2
Technical content
Key Features: 8W Output Power 2:1 Input Voltage Range 1,500 VDC Isolation -40ºC Operation Compact DIP Case Single & Dual Outputs 1.0 MH MTBF Industry Standard Pin-Out Lowest Cost!! A800ERW Low Cost, 8W DIP Wide Input Range DC/DC Con vert ers MicroPower Direct
292 Page Street
Stoughton, MA 02072 USA T: (781) 344-8226 F: (781) 344-8481 E: sales@micropowerdirect.com W: www.micropowerdirect.com RoHS Compliant Input Parameter Conditions Min. Typ. Max. Units Input Voltage Range 5 VDC Input 4.5 5.0 9.0 VDC12 VDC Input 9.0 12.0 18.0 24 VDC Input 18.0 24.0 36.0 48 VDC Input 36.0 48.0 75.0 Input Filter π (Pi) Filter Reverse Polarity Input Current 1.0 A Short Circuit Input Power 1,000 3,000 mW Output Parameter Conditions Min. Typ. Max. Units Output Voltage Accuracy ±2.0 % Output Voltage Balance Dual Output , Balanced Loads ±2.0 % Line Regulation Vin = Min to Max ±0.5 % Load Regulation, Single Output Iout = 25% to 100% ±0.5 % Load Regulation, Dual Output Iout = 25% to 100% ±2.0 % Ripple & Noise (20 MHz) (Note 1) 3.3 VDC, 5 VDC Output 80 mV P - P Ripple & Noise (20 MHz) All Other Outputs. 1 % P - P Output Power Protection 110 % Transient Recovery Time (Note 2) 50% Load Step Change 300 µSec Transient Response Deviation ±2.0 ±6.0 % Temperature Coeffi cient ±0.05 %/ ºC Output Short Circuit Continuous General Parameter Conditions Min. Typ. Max. Units Isolation Voltage 60 Seconds 1,500 VDC Isolation Resistance 500 VDC 1,000 MΩ Isolation Capacitance 100 kHz, 1V 380 pF Switching Frequency 300 kHz Environmental Parameter Conditions Min. Typ. Max. Units Operating Temperature Range Ambient -40 +25 +75 ºC Operating Temperature Range Case -40 +95 ºC Storage Temperature Range -40 +115 ºC Cooling Free Air Convection Humidity RH, Non-condensing 95 % Physical Case Material Non-Conductive Black Plastic (UL94-V0) Weight 0.56 Oz (16g) Reliability Specifi cations Parameter Conditions Min. Typ. Max. Units MTBF MIL HDBK 217F, 25ºC, Gnd Benign 1.0 MHours Absolute Maximum Ratings Parameter Conditions Min. Typ. Max. Units Input Voltage Surge (1 Sec) 5 VDC Input -0.7 16.0 VDC12 VDC Input -0.7 25.0 24 VDC Input -0.7 50.0 48 VDC Input -0.7 100.0 Lead Temperature 1.5 mm From Case For 10 Sec 260 ºC Internal Power Dissipation All Models 2,500 mW Caution: Exceeding Absolute Maximum Ratings may damage the module. These are not continuous operating ratings. Series A Budget Saver!!Electrical Specifi cations Specifi cations typical @ +25°C, nominal input voltage & rated output current, unless otherwise noted. Specifi cations subject to change without notice.
Mechanical Notes: All dimensions are typical in inch es (mm) Tolerance x.xx = ±0.01 (±0.25) Notes: 1. When measuring output ripple, it is recommended that an external 0.47 µF ceramic capacitor be placed from the +Vout pin to the -Vout pin for single output units and from each output to common for dual output units. For noise sensitive applications, the use of 3.3 µF capacitors will reduce the output ripple. 2. Transient recovery is measured to within a 1% error band for a load step change of 50% to 100%. 3. Operation at no-load will not damage these units. However, they may not meet all specifi cations. 4. Dual output units may be connected to provide a 10 VDC, 24 VDC or 30 VDC output. To do this, connect the load across the positive (+Vout) and negative (-Vout) outputs and fl oat the output common. 5. The converter should be connected to a low ac-impedance source. An input source with a highly inductive impedance may affect the stability of the con- verter. In applications where the converter output loading is high and input power is supplied over long lines, it may be necessary to use a capacitor on the input to insure start-up. In this case, it is recommended that a low ESR (ESR <1.0 Ω at 100 kHz) capacitor be mounted close to the converter. For 5V input units a 10 µF is recommended, for 12V input units, a 3.3 µF; and for 24V & 48V units a 2.2 µF. 6. It is recommended that a fuse be used on the input of a power supply for protection. See the table above for the correct rating. Model Number Input Output Effi ciency (%, Typ) Fuse Rating Slow-Blow (mA) Voltage (VDC) Current (mA) Refl ected Ripple Current (mA, Typ) Voltage (VDC) Current (mA, Max) Current (mA, Min)Nominal Range Full-Load No-Load Pin Single Dual Pin Single Dual 2, 3 -Vin -Vin 14 +Vout +Vout
9 No Pin Common 16 -Vout Common
11 NC -Vout 22, 23 +Vin +Vin
NC: No Connection Pin Connections MicroPower Direct www.micropowerdirect.com 292 Page Street, STE D, Stoughton, MA 02072 TEL: (781) 344-8226 FAX: (781) 344-8481 E-Mail: sales@micropowerdirect.com Derating Curve