A300RUI MPD | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 2

Technical content

/square6 4:1 Input Range /square6 3.5 kVDC I/O Isolation /square6 3W Output Power /square6 Single & Dual Outputs /square6 Tight Line/Load Regulation /square6 Low Cost Electrical Specifi cations Specifi cations typical @ +251C with nominal input voltage & rated output current, unless otherwise noted. Specifi cations subject to change without notice. Input Parameter Conditions Min. Typ. Max. Units Input Filter π (Pi) Filter Short Circuit Input Power 2,000 mW Output Parameter Conditions Min. Typ. Max. Units Output Voltage Accuracy !0.5 !1.0 % Output Voltage Balance Dual Output , Balanced Loads !0.5 !1.0 % Line Regulation Vin = Min to Max !0.2 !0.5 % Load Regulation Iout = 10% to 100% !0.2 !0.5 % Ripple & Noise (20 MHz) 60 mV P - P Output Power Protection 120 % Transient Recovery Time (Note 1) 25% Load Step Change 150 500 µSec Transient Response Deviation !2.0 % Temperature Coeffi cient !0.01 !0.02 %/1C Output Short Circuit Continuous General Parameter Conditions Min. Typ. Max. Units Isolation Voltage 60 Seconds 3,500 VDC Isolation Resistance 500 VDC 1,000 M Ω Isolation Capacitance 100 kHz, 1V 390 pF Leakage Current 1.0 mA Switching Frequency 300 kHz Environmental Parameter Conditions Min. Typ. Max. Units Operating Temperature Range -40 +85 1C Storage Temperature Range -40 +125 1C Cooling Free Air Convection Humidity RH, Non-condensing 90 % Physical Case Material Metal with Non-Conductive Base Weight 0.74 Oz (21g) Reliability Specifi cations Parameter Conditions Min. Typ. Max. Units MTBF MIL HDBK 217F, 251C, Gnd Benign 950 kHours Absolute Maximum Ratings Parameter Conditions Min. Typ. Max. Units Input Voltage Surge (1 Sec) 24 VDC Input -0.7 50.0 VDC48 VDC Input -0.7 100.0 Internal Power Dissipation All Models 2,500 mW Caution: Exceeding Absolute Maximum Ratings may damage the module. These are not continuous operating ratings. MicroPower Direct 3W, Ultra-Wide Input High Isolation DC/DC Converters A300RUI Series MicroPower Direct /square6 TEL: (781) 344-8226 /square6 FAX: (781) 344-8481 /square6 E-Mail: sales@micropowerdirect.com /square6 WEB: www/micropowerdirect.com

Notes: All dimensions are typical in inches (mm) Tolerance x.xx = !0.01 (!0.25) Pin 1 is marked by a “dot” or indentation on the top of the unit Model Number Input Output Effi ciency (%, Typ) Fuse Rating Slow-Blow (mA) Voltage (VDC) Current (mA) Refl ected Ripple Current (mA, Typ) Voltage (VDC) Current (mA, Max) Current (mA, Min)Nominal Range Full-Load No-Load A301RUI 24 9.0 - 36.0 166 12 5 5.0 600 60.0 75 1,000 A302RUI 24 9.0 - 36.0 158 12 5 12.0 250 25.0 79 1,000 A303RUI 24 9.0 - 36.0 158 12 5 15.0 200 20.0 79 1,000 A304RUI 24 9.0 - 36.0 166 12 5 !5.0 !300 !30.0 75 1,000 A305RUI 24 9.0 - 36.0 158 12 5 !12.0 !125 !12.0 79 1,000 A306RUI 24 9.0 - 36.0 158 12 5 !15.0 !100 !10.0 79 1,000 A311RUI 48 18.0 - 72.0 83 7 5 5.0 600 60.0 75 500 A312RUI 48 18.0 - 72.0 80 7 5 12.0 250 25.0 78 500 A313RUI 48 18.0 - 72.0 79 7 5 15.0 200 20.0 78 500 A314RUI 48 18.0 - 72.0 83 7 5 !5.0 !300 !30.0 76 500 A315RUI 48 18.0 - 72.0 80 7 5 !12.0 !125 !12.0 79 500 A316RUI 48 18.0 - 72.0 80 7 5 !15.0 !100 !10.0 79 500

232 Tosca Drive, Stoughton, MA 02072

www.micropowerdirect.com sales@micropowerdirect.com phone: (781) 344 - 8226 * fax: (781) 344 - 8481 Mechanical Dimensions MicroPower Direct Pin Single Dual 2, 3 -Vin -Vin

9 No Pin Common

11 NC -Vout

22, 23 +Vin +Vin NC: No Connection Pin Connections Single Output (µF Max) Dual Output (µF Max) 1,000 !220 Capacitive Load Notes: 1. Transient recovery is measured to within a 1% error band for a load step change of 75% tp 100%. 2. Dual output units may be connected to provide a 10V, 24V or 30V output. To do this connect the load across the positive (+Vout) and negative (-Vout) outputs and fl oat the output common. Output Power % Ambient Temperature ( C) -5%/ C1 Bottom 1.25 (31.8) 0.18 (4.6) 0.10 (2.54)

0.02 DIA

(0.5) 0.40 (10.2) 0.15 (3.8) Side 0.10 (2.54) 0.60 (15.2) 0.80 (20.3) Derating Curve